High-temperature thermoelectric properties of Ca3Co4O9+δ with Eu substitution

We have prepared polycrystalline Ca_3−xEu_xCo₄O_9+δ (x=0, 0.15, 0.3 and 0.45) samples using a sol-gel process followed by SPS sintering and investigated the Eu substitution effects on their high-temperature thermoelectric properties. With the Eu substitution, both the electrical resistivity and thermopower increase monotonously. This could be attributed to the decrease of hole concentrations by substitution of trivalent Eu³⁺ for divalent Ca²⁺. The Eu substituted samples (x=0.15, x=0.3) have lower thermal conductivity than Ca₃Co₄O_9+δ due to their lower electronic and lattice thermal conductivity. The dimensionless figure of merit ZT reaches 0.3 at 1000 K for the sample of Ca_2.7Eu_0.3Co₄O_9+δ.     

Co-reduction synthesis of new LnxSb2−xS3 (Ln: Nd, Lu, Ho) nanomaterials and investigation of their physical properties

New Ln_xSb_2−xS₃ (Ln: Lu³⁺, Ho³⁺, Nd³⁺)-based nanomaterials were synthesized by a co-reduction method. Powder XRD patterns indicate that the Ln_xSb_2−xS₃ crystals (Ln=Lu³⁺, Ho³⁺, x=0.00−0.1 and Ln=Nd³⁺, x=0.00−0.08) are isostructural with Sb₂S₃. SEM images show that doping of Lu³⁺ and Ho³⁺ ions in the lattice of Sb₂S₃ results in nanorods while that in Nd³⁺ leads to nanoflowers. UV-vis absorption and emission spectroscopy reveal mainly electronic transitions of the Ln³⁺ ions in case of Ho³⁺ and Nd³⁺ doped nanomaterials. Emission spectra show intense transitions from excited to ground state of Ln³⁺. Emission spectra of doped materials, in addition to the characteristic red emission peaks of Sb₂S₃, show other emission bands originating from f-f transitions of the Ho³⁺ ions. TGA curves indicated that Sb₂S₃ has the highest thermal stability. The electrical conductance of Ln-doped Sb₂S₃ is higher than undoped Sb₂S₃, and increase with temperature.     

Ho3+掺杂对ZnO薄膜的微观结构和磁性的影响

研究Ho³⁺掺杂对氧化锌半导体材料的微结构和磁学性质影响. 利用热蒸发技术制备了一系列沉积在Si(100)衬底的Zn_1-xHo_xO(x=0.0、0.04、0.05）薄膜. X射线光谱、表面形貌以及磁性的实验结果表明,Ho³⁺掺杂对ZnO薄膜材料的性能影响很大. X射线衍射图显示峰位出现高角度转变并且趋向于(101)取向,在ZnO晶格显示Ho³⁺置换. 扫描电子显微镜和能谱仪对薄膜的表面形貌以及化学     

Influence of co-doping different rare earth ions on CaGa2S4: Eu, RE(RE=Ln) phosphors

Photoluminescent phosphors CaGa₂S₄: Eu²⁺, RE³⁺ (RE³⁺ including all rare earth ions except for Sc³⁺, Pm³⁺, Eu³⁺ and Lu³⁺) were prepared by sintering at high temperature in a reductive atmosphere, and their luminescent properties were studied intensively. The influences of co-doping rare earth ions on their luminescent properties were also investigated. No remarkable differences were found from excitation spectra of co-doped phosphors CaGa₂S₄: Eu²⁺, RE³⁺ in contrast with that of phosphor CaGa₂S₄: Eu²⁺, but there were a few differences in emission spectra of Ce³⁺, Pr³⁺ or Ho³⁺ co-doped phosphors. Phosphors CaGa₂S₄: Eu²⁺, RE³⁺ (RE=Ce, Pr, Gd, Tb, Ho and Y) had persistent afterglow, and very short afterglow was shown for Nd³⁺ or Er³⁺ co-doped phosphors, but no long afterglow appeared when auxiliary activator was La³⁺, Sm³⁺, Dy³⁺, Tm³⁺ or Yb³⁺. Among the phosphors with long-lasting phosphorescence, in our experiments, CaGa₂S₄: Eu²⁺, Ho³⁺ had the longest and the highest brightness long yellow afterglow. Thermo-luminescence of all co-doped phosphors was measured to find the answer of different influences from different rare earth auxiliary activators.     

Critical current density and flux pinning in La2−xPrxCa2x Ba2Cu4+2xOz (x=0.1-0.5) superconductors

Polycrystalline La_2−xPr_xCa_2xBa₂Cu_4+2xO_z (LPCaBCO) compounds with x=0.1-0.5 were synthesized by solid-state reaction method and studied by room temperature X-ray diffraction, dc resistivity, dc magnetization and iodometry. The superconducting transition temperatures in these tetragonal triple perovskite compounds increases from 32 to 62 K (T_c^onset values) with increasing dopant concentration. The mixing of rare earth La³⁺ and Pr^3+/4+ ions at rare earth site (La³⁺) along with substitution of divalent Ca²⁺ results in the shrinkage of unit cell volume. The contraction of unit cell volume due to larger ion being substituted by smaller ions, gives rise to creation of pinning centres in the unit cell leading to increase in critical current density and flux pinning.     

The effect of Er doping on the spin reorientation transition in Ho1−xErxAl2

The magnetothermal properties of pseudo binary Ho_1−xEr_xAl₂ alloys have been investigated by heat capacity measurements. Two anomalies are observed in the heat capacity of HoAl₂. A sharp peak at 20 K represents the first order spin reorientation transition, and a second order anomaly occurs in the vicinity of the ferromagnetic transition at 32 K. As Ho is partially replaced by Er in Ho_1−xEr_xAl₂ the sharpness of the first order heat capacity peak diminishes with increasing Er concentration, while the temperature of this transition remains practically unaffected. The second order ferromagnetic transition shifts to higher temperature region with increasing Er concentration. The observed behaviors are explained considering the geometry of 4f charge densities of Ho³⁺ and Er³⁺ and the easy magnetization directions of HoAl₂ and ErAl₂.     

Effect of holmium substitution for the improvement of multiferroic properties of BiFeO3

This paper reports on multiferroic properties of Ho substituted BiFeO₃ (Bi_1−xHo_xFeO₃) ceramics. It is observed that for x=0.15, a prominent ferroelectric loop is seen at 300 K even if the system remains in rhombohedral (R3c) phase without appearance of any observable impurity phases. A well shaped M-H loop is observed at 10 K for x=0.15. However it showed ferromagnetism, confirming the contribution of Ho³⁺ towards enhancement of ferromagnetic properties of BiFeO₃ at 300 K. Suppression of impurity phases of pure BiFeO₃ bulk ceramic favors the reduction of mobile oxygen vacancies and reduces leakage current, due to which ferroelectric properties of BiFeO₃ is enhanced. We argue that Ho substitution at Bi site is likely to suppress the spiral spin modulation and at the same time increase the canting angle, which favors enhanced multiferroic properties. XRD, SEM, magnetization, polarization and chemical bonding analysis measurements were carried out to explain the multiferroic behavior.     

Effects of Cr doping in bilayered manganite LaSr2Mn2O7: Resistivity, thermoelectric power, and thermal conductivity

Systematic studies of resistivity, thermoelectric power, and thermal conductivity have been performed on polycrystalline bilayered manganites LaSr₂Mn_2−xCr_xO₇ (0≤x≤0.2). It is found that the temperature dependence of both Seebeck coefficient S(T) and resistivity ρ(T) in the high temperature region follows the small polaron transport mechanism for all the samples. But in the low temperature region, variable-range-hopping (VRH) model matches the experimental data better. In addition, the maximum of absolute S(T) at low temperatures is gradually suppressed for the sample with Cr-doping level of x>0.04, implying that a new FM order probably arises. With decreasing the temperatures further, S(T) has a sign change and becomes positive for the sample with Cr-doping level of x>0.04, indicating that there may occur a variation of the type of charge carrier. As to thermal conduction κ(T), the low-temperature peak is suppressed due to Cr-doping. The variation of κ(T) is analyzed based on the combined effect due to the suppression of local Mn³⁺O₆ Jahn-Teller (JT) lattice distortion because of the substitution of Cr³⁺ ions for Mn³⁺ ions, which results in the increase in thermal conduction, and the introduction of the disorder due to Cr-doping, which contributes to the decrease in thermal conduction.     

Electrochemical luminescence of Mg1−xCaxIn2O4:Er electrodes

Improvement for electrochemical luminescence (ECL) property of MgIn₂O₄ is attempted by partial exchange of Mg²⁺ ion in MgIn₂O₄ to Ca²⁺ ion. Mg_1−xCa_xIn₂O₄ solid solution was obtained in the region 0<x<0.4. Efficiency for ECL per unit current for Mg_1−xCa_xIn₂O₄:Er³⁺ increased with the increase in the ratio of Ca²⁺ ion, and showed a peak at x=0.25 and then decreased steeply. ECL efficiency for other rare-earth ion-(RE:Sm, Eu, Ho) doped Mg_1−xCa_xIn₂O₄ also increased comparing with those for MgIn₂O₄:RE. This Ca²⁺ addition effect on the ECL efficiency seems to be caused by the improvement of the efficiency for the impact activation.     

The effect of Mn substitution on thermoelectric properties of Ca3MnxCo4−xO9 at low temperatures

The effects of partial substitution of Mn for Co on the thermoelectric properties of Ca₃Mn_xCo_4−xO₉ (x=0, 0.03, 0.9), prepared by sol-gel process, were investigated at the temperatures from 380 K down to 5 K. The results indicate that the substitution of Mn for Co results in increase in thermopower at temperatures >∼80 K, and substantial (23-31% at 300 K) decrease in lattice thermal conductivity in the whole temperature range investigated. The temperature behavior of ZT suggests that Ca₃Mn_xCo_4−xO₉ with light Mn substitution would be a promising candidate for high-temperature thermoelectric applications.     

Charge order melting and magnetic transition in Nd0.5(1+x)Ca0.5(1−x)Mn(1−x)CrxO3 system

The magnetic property of double doped manganite Nd_0.5(1+x)Ca_0.5(1−x)Mn_(1−x)Cr_xO₃ with a fixed ratio of Mn³⁺:Mn⁴⁺=1:1 has been investigated. For the undoped sample, it undergoes one transition from charge disordering to charge ordering (CO) associated with paramagnetic (PM)-antiferromagnetic (AFM) phase transition at T<250 K. The long range AFM ordering seems to form at 35 K, rather than previously reported 150 K. At low temperature, an asymmetrical M-H hysteresis loop occurs due to weak AFM coupling. For the doped samples, the substitution of Cr³⁺ for Mn³⁺ ions causes the increase of magnetization and the rise of T_c. As the Cr³⁺ concentration increases, the CO domain gradually becomes smaller and the CO melting process emerges. At low temperature, the FM superexchange interaction between Mn³⁺ and Cr³⁺ ions causes a magnetic upturn, namely, the second FM phase transition.     

Charge transfer excitation of the Nd3+, Sm3+, Dy3+, Ho3+, Er3+ and Tm3+ emission in CaGa2S4

The excitation spectra of the Nd³⁺, Sm³⁺, Dy³⁺, Ho³⁺, Er³⁺ and Tm³⁺ emission in the sodium-compensated CaGa₂S₄ host lattice, a sulfide with wide band gap, contain an intense band below the absorption edge. Comparison of the energy of its maximum with thermodynamic data and correlations to Jørgensen's refined spin-pairing theory predictions allow one to ascribe this band to a charge transfer transition ending onto 4f orbitals. The irregular variation within the rare earth series contrasts with the monotonic variation of the absorption edge in stoichiometric rare earth sulfides (e.g. NaLnS₂), associated with interband transitions.     

Double metal-insulator peaks and effect of Sm substitution on magnetic and transport properties of hole-doped La0.85Ag0.15MnO3

La_0.85−xSm_xAg_0.15MnO₃ (x=0−0.2) ceramics were prepared using the conventional solid-state synthesis method to investigate the effect of Sm³⁺ substitution on magnetic and electrical transport properties. Magnetic susceptibility versus temperature measurements showed all samples exhibit ferromagnetic to paramagnetic transition with Curie temperature, T_c decreasing from 283 K (x=0) to 164 K (x=0.2) with increasing Sm³⁺. The observed slope in susceptibility, χ′ versus temperature curves below T_c indicates the possible presence of FM and AFM phases in the metallic region. In addition, a deviation from the Curie-Weiss law above T_c in 1/χ′ versus T curves indicates the existence of a Griffith's phase in the x=0.05−0.2 samples due to the Sm³⁺ ion substitution. The Griffith temperature, T_G was found to decrease from 295 K (x=0.05) to 229 K (x=0.2). Electrical resistivity measurements of the samples in zero field showed transition from metallic behavior to insulating behavior as the temperature was increased. For x=0, two metal-insulator, MI transition peaks were observed at T_p1=282 K and at T_p2=250 K. Both peaks shifted to lower temperatures with the increase in Sm³⁺. The relative resistivity of the first peak to the second peak decreases with increasing Sm³⁺ for x>0.05 while at x=0.2 the T_p1 peak was strongly suppressed. Magnetoresistance, MR was observed to weaken with Sm³⁺ substitution. The metallic region of the ρ(T) curve of the x=0−0.15 samples was fitted to the model of electron-electron and electron-magnon scattering while the insulating region was fitted to the variable range hopping, VRH model. The resistivity behavior indicated that the substitution of Sm³⁺ weakened the double exchange process and enhanced the Jahn-Teller effect. Our results indicated that the T_p1 peak is strongly related to the double-exchange mechanism while the T_p2 peak is suggested to originate from magnetic inhomogeneity.     

Superconductivity in CoSr2(Y1−xCax)Cu2O7+δ

The roles of aliovalent Ca^II-for-Y^III substitution and high-pressure-oxygen annealing in the process of ‘superconducterizing’ the Co-based layered copper oxide, CoSr₂(Y_1−xCa_x)Cu₂O_7+δ (Co-1212), were investigated. The as-air-synthesized samples up to x=0.4 were found essentially oxygen stoichiometric (−0.03≤δ≤0.00). These samples, however, were not superconducting, suggesting that the holes created by the divalent-for-trivalent cation substitution are trapped on Co in the charge reservoir. Ultra-high-pressure heat treatment carried out at 5 GPa and 500 °C for 30 min in the presence of Ag₂O₂ as an excess oxygen source induced bulk superconductivity in these samples. The highest T_c was obtained for the high-oxygen-pressure treated x=0.3 sample at ∼40 K.     

The correlation between structure and magnetic properties in the manganites La0.7Ca0.3−xTexMnO3 (0≤x≤0.15)

The effect of Te-doping at La-site on structural, magnetic and transport properties in the manganites La_0.7Ca_0.3−xTe_xMnO₃ (0≤x≤0.15) has been investigated. All samples show an orthorhombic structure (O′-Pbnm) at room temperature. It shows that the Mn-O-Mn bond angle decreases and the Mn-O bond length increases with the increase in the Te content. All samples exhibit an insulator-metal (I-M) transition and the resistivity increases with the increase in the Te-doping level. Additionally, the Curie temperature T_c decreases and the transition becomes broader with increasing Te-doping level, in contrast, the magnetization of Te-doping samples at low temperatures decrease with increasing x as x≤0.10 and then increase with further increasing x to 0.15. The results are discussed in terms of Jahn-Teller (JT) vibrational anisotropy Q₃/Q₂ and the opening of the new DE channel between Mn²⁺-O-Mn³⁺ due to the introduction of Mn²⁺ ions because of the substitution of Te⁴⁺ ions for Ca²⁺ ions.     

Yb3+敏化的Er3+/Ho3+共掺碲酸盐玻璃的上转换发光研究

用高温熔融法制备了系列Er³⁺/Yb³⁺共掺，Ho³⁺/Yb³⁺共掺，和Er³⁺/Yb³⁺/Ho³⁺三掺碲酸盐玻璃，在975nm激光抽运下三种掺杂玻璃中都出现了较强的绿光和红光上转换.研究了Yb³⁺离子对Er³⁺和Ho³⁺离子上转换发光强度的影响以及Yb³⁺→Er关键词： 3+/Yb³⁺/Ho³⁺共掺')" href="#">Er³⁺/Yb³⁺/Ho³⁺共掺 碲酸盐玻璃 光谱性质 上转换     

Effect of indium addition on the structure and magnetic properties of YIG

In this work we report the structure and magnetic properties of a series of single-phase indium-substituted yttrium iron garnet (In-YIG) nanoparticles with nominal composition of Y₃In_xFe_5−xO₁₂ (x=0.1, 0.2, 0.3 and 0.4) prepared by conventional mixed oxide route. Based on XRD results, the lattice parameters of the samples increased with increase in In³⁺ content due to its larger ionic radius. Mössbauer results confirmed the substitution of In³⁺ for Fe³⁺ in [a] site of YIG structure. Further, the magnitudes of the magnetic hyperfine field (MHF) were seen to reduce due to indium substitution. Moreover, a rising trend was observed for saturation magnetization (M_S) of the samples with x>0.2 owing to the substitution of non-magnetic In³⁺ for Fe³⁺. However, the observed initial drop of M_S for the sample with x=0.2 compared to that with x=0.1 is possibly attributed to the dominance of spin canting over the net magnetization rise caused by In³⁺ in [a] sites.     

Synthesis and up-conversion luminescence properties of Ho3+, Yb3+ co-doped BaLa2ZnO5

Up-conversion phosphors BaLa₂ZnO₅ co-doped with Ho³⁺/Yb³⁺ were synthesized by high temperature solid-state reaction method. The phase composition of the phosphors was characterized by X-ray diffraction (XRD). The structure of BaLa₂ZnO₅: 0.75% Ho/15% Yb phosphor was refined by the Rietveld method and results showed the decreased unit cell parameters and cell volume after doping Ho³⁺ and Yb³⁺, indicating Ho³⁺ and Yb³⁺ have successfully replaced La³⁺. Under the excitation of 980 nm diode laser, the strong green and weak red up-conversion emissions centered at 548 nm, 664 nm and 758 nm were observed, which originating from ⁵S₂, ⁵F₂→⁵I₈, ⁵F₄→⁵I₈ and ⁵S₂, ⁵F₂→⁵I₇ transitions of Ho³⁺ ions, respectively. The optimum doping concentrations of Ho³⁺ and Yb³⁺ were determined to be 0.75% and 15%, and the corresponding Commission International de L'Eclairage (CIE) coordinates are calculated to be x=0.298 and y=0.692. The related UC mechanism of Ho³⁺/Yb³⁺ co-doped BaLa₂ZnO₅ depending on pump power was studied in detail. The results indicate that BaLa₂ZnO₅: Ho³⁺/Yb³⁺ can be an effective candidate for up-conversion yellowish-green light emitter.     

Effect of Mn-site vacancies on the magnetic entropy change and the Curie temperature of La0.67Ca0.33Mn1−xO3 perovskite

Single-phase polycrystalline samples of La_0.67Ca_0.33Mn_1−xO₃ (x=0.00, 0.02, 0.04, 0.06) have been prepared using the sol-gel method. The structure, magnetocaloric properties and the Curie temperature of the samples with different Mn vacancy concentrations have been investigated. The experimental results show that vacancy doping at the Mn-sites has a significant influence on the magnetic properties of La_0.67Ca_0.33Mn_1−xO₃. The Curie temperature decreases monotonically with increasing the Mn-site vacancy concentration x. A remarkable enhancement of the magnetic entropy change has been obtained in the La_0.67Ca_0.33Mn_0.98O₃ sample. The entropy change reaches |ΔS_M|=3.10 J kg⁻¹ K⁻¹ at its Curie temperature (264 K) under an applied magnetic field H=10 kOe, which is almost the same value as that of pure Gd.     

Dielectric properties of lanthanum-doped CaCu3Ti4O12 synthesized by semi-wet route

Effect of La³⁺ doping at Ca²⁺ site in CaCu₃Ti₄O₁₂ has been examined. Compositions with x=0.10, 0.20 and 0.30 were synthesized in the system Ca_(1−3x/2)La_xCu₃Ti₄O₁₂ by semi-wet method. Powder X-ray diffraction confirmed the formation of monophasic compounds. The structure remains cubic similar to CaCu₃Ti₄O₁₂. Lattice parameter increases slightly with increasing La³⁺ concentration. Microstructure has been studied using scanning electron microscopy (SEM). Average grain size is in the range 2-4 μm for various compositions. Energy-dispersive spectrometer (EDS) studies confirm the stoichiometry of the synthesized materials. Dielectric constant, dielectric loss and conductivity of the samples decrease with increasing lanthanum concentrations.