Influence of boron on the initial stages of Si molecular beam epitaxy on Si(1 1 1) studied by reflection high-energy electron diffraction

The influence of boron as a function of coverage on molecular beam epitaxial Si growth on Si(1 1 1) surface was systematically studied by reflection high-energy electron diffraction. At boron coverage above 0.3 monolayer regular oscillations occur with a period typically for two-bilayers, whereas at lower boron coverage a transient behaviour with irregular intensity oscillations was observed in the initial growth stages. This behaviour can be attributed to a superposition of a bilayer and a two-bilayer dominated growth mode. The appearance of these two growth modes is discussed in terms of an initial surface defect-induced nucleation of bilayer-high Si islands and the formation of two-bilayers-high Si islands on top of the van der Waals like boron-covered surface, respectively. We suggest that these surface defects are of intrinsic nature, and their number only depends on the amount of boron at the surface. The oscillations become regular during further Si deposition with a bilayer period, indicating a diminishing influence of the layer/substrate interface on the growth processes.     

The epitaxial sexiphenyl (0 0 1) monolayer on TiO2(1 1 0): A grazing incidence X-ray diffraction study

A para-sexiphenyl monolayer of near up-right standing molecules (nominal thickness of 30 Å) is investigated in-situ by X-ray diffraction using synchrotron radiation and ex-situ by atomic force microscopy. A terrace like morphology is observed, the step height between the terraces is approximately one molecular length. The monolayer terraces, larger than 20 μm in size, are extended along the [0 0 1] direction of the TiO₂(1 1 0) substrate i.e. along the Ti-O rows of the reconstructed substrate surface. The structure of the monolayer and its epitaxial relationship to the substrate is determined by grazing incidence X-ray diffraction. Extremely sharp diffraction peaks reveal high crystalline order within the monolayer, which was found to have the bulk structure of sexiphenyl. The monolayer terraces are epitaxially oriented with the (0 0 1) plane parallel to the substrate surface (out-of-plane order). Four epitaxial relationships are observed. This in-plane alignment is determined by the arrangement of the terminal phenyl rings of the sexiphenyl molecules parallel to the oxygen rows of the substrate.     

Crystal growth of SrTiO3 films on H-terminated Si(1 1 1) with SrO buffer layers

Growth of epitaxial SrTiO₃ (STO) films has been examined on H-terminated Si(1 1 1) with SrO buffer layers. The epitaxial SrO buffer layers have reduced stress on H-terminated Si substrates. On the SrO buffer layers, the STO films grow epitaxially with triple domains at low temperature. Each STO domain has equivalent epitaxial relationship to SrO buffer layers, STO(1 1 0)∥SrO(1 1 1) and .     

Characterization of bicrystalline epitaxial LaNiO3 films fabricated on MgO (1 0 0) substrates by pulsed laser deposition

A series of metallic LaNiO₃ (LNO) thin films were deposited on MgO (1 0 0) substrates by pulsed laser deposition (PLD) under the oxygen pressure of 20 Pa at different substrate temperatures from 450 to 750 °C. X-ray diffraction (XRD) was used to characterize the crystal structure of LNO films. θ-2θ scans of XRD indicate that LNO film deposited at a substrate temperature of 700 °C has a high orientation of (l l 0). At other substrate temperatures, the LNO films have mixed phases of (l l 0) and (l 0 0). Furthermore, pole figure measurements show that LNO thin films, with the bicrystalline structure, were epitaxially deposited on MgO (1 0 0) substrates in the mode of LNO (1 1 0)//MgO (1 0 0) at 700 °C. Reflection high-energy electric diffraction (RHEED) and atomic force microscopy (AFM) were also performed to investigate the microstructure of LNO films with the high (l l 0) orientation. RHEED patterns clearly confirm this epitaxial relationship. An atomically smooth surface of LNO films at 700 °C was obtained. In addition, bicrystalline epitaxial LNO films, fabricated at 700 °C, present a excellent conductivity with a lower electrical resistivity of 300 μ Ω cm. Thus, the obtained results indicate that bicystalline epitaxial LNO films could serve as a promising candidate of electrode materials for the fabrication of ferroelectric or dielectric films.     

Variety of iron silicides grown on Si(0 0 1) surfaces by solid phase epitaxy: Schematic phase diagram

We systematically studied the formation of various iron-silicide phases, grown on Si(0 0 1) surfaces by solid phase epitaxy, with scanning tunneling microscopy, low-energy electron diffraction and reflection high-energy electron diffraction. We found and studied the phases of c(2 × 2) islands, rectangle-like islands, elongated islands, layered islands, dome-like islands, eddy and cracked structures, and small clusters. A schematic phase diagram of these phases is successfully summarized against iron coverage at room temperature and subsequent annealing temperature.     

X-ray multiple diffraction in the characterization of TiNO and TiO2 thin films grown on Si(0 0 1)

TiO₂ and TiN_xO_y thin films grown by low pressure metal-organic chemical vapor deposition (LP-MOCVD) on top of Si(0 0 1) substrate were characterized by X-ray multiple diffraction. X-ray reflectivity analysis of TiO₂[1 1 0] and TiNO[1 0 0] polycrystalline layers allowed to determine the growth rate (−80 Å/min) of TiO₂ and (−40 Å/min) of TiNO films. X-ray multiple diffraction through the Renninger scans, i.e., ?-scans for (0 0 2)Si substrate primary reflection is used as a non-conventional method to obtain the substrate lattice parameter distortion due to the thin film conventional deposition, from where the information on film strain type is obtained.     

Growth and annealing of zinc-blende CdSe thin films on GaAs (0 0 1) by molecular beam epitaxy

CdSe thin films have been grown on GaAs (0 0 1) substrates by molecular beam epitaxy (MBE). The effects of substrate temperature and annealing treatment on the structural properties of CdSe layers were investigated. The growth rate slightly decreases due to the accelerated desorption of Cd from CdSe surface with an increase in the temperature. The sample grown at 260 °C shows a polycrystalline structure with rough surface. As the temperature increases over 300 °C, crystalline CdSe (0 0 1) epilayers with zinc-blende structure are achieved and the structural quality is improved remarkably. The epilayer grown at 340 °C displays the narrowest full-width at half-maximum (FWHM) from (0 0 4) reflection in double-crystal X-ray rocking curve (DCXRC) and the smallest root-mean-square (RMS) roughness of 0.816 nm. Additionally, samples fabricated at 320 °C were annealed in air for 30 min to study the films’ thermal stability. X-ray diffraction (XRD) results indicate that the zinc-blende structure remains unchanged when the annealing temperature is elevated to 460 °C, meaning a good thermal stability of the cubic CdSe epilayers.     

Solid phase epitaxy of Ge films on CaF2/Si(1 1 1)

At room temperature deposited Ge films (thickness < 3 nm) homogeneously wet CaF₂/Si(1 1 1). The films are crystalline but exhibit granular structure. The grain size decreases with increasing film thickness. The quality of the homogeneous films is improved by annealing up to 200 °C. Ge films break up into islands if higher annealing temperatures are used as demonstrated combining spot profile analysis low energy electron diffraction (SPA-LEED) with auger electron spectroscopy (AES). Annealing up to 600 °C reduces the lateral size of the Ge islands while the surface fraction covered by Ge islands is constant. The CaF₂ film is decomposed if higher annealing temperatures are used. This effect is probably due to the formation of GeF_x complexes which desorb at these temperatures.     

Thin PTCDA films on Si(0 0 1): 1. Growth mode

We have studied the interface and thin film formation of the organic molecular semiconductor 3,4,9,10 perylene tetracarboxylic dianhydride (PTCDA) on clean and on hydrogen passivated Si(0 0 1) surfaces. The studies were made by means of high resolution X-ray photoelectron spectroscopy (HRXPS), near edge X-ray absorption fine structure (NEXAFS), low energy electron diffraction (LEED), and atomic force microscopy (AFM). On the passivated surface the LEED pattern is somewhat diffuse but reveals that the molecules grow in several ordered domains with equivalent orientations to the substrate. NEXAFS shows that the molecules are lying flat on the substrate. The Si 2p XPS line shape is not affected when the film is deposited so it can be concluded that the interaction at the interface between PTCDA and the substrate is weak. The evolution of the film formation appears to be homogeneous for the first monolayer with a nearly complete coverage of flat lying molecules based on the XPS attenuation. For layer thickness of 0.5-2 monolayers (ML) the molecules start to form islands, attracting the molecules in between, leaving the substrate partly uncovered. For thicker films there is a Stranski-Krastanov growth mode with thick islands and a monolayer thick film in between. For the clean surface the ordering of the film is much lower and angle resolved photoelectron spectroscopy (ARPES) of the molecular orbitals have only a small dependence of the emission angle. NEXAFS shows that the molecules do not lie flat on the surface and also reveal a chemical interaction at the interface.     

Si nucleation on Si(1 1 1)-7 × 7: From cluster pairs to 2D islands

Nucleation of 2D islands in Si/Si(1 1 1)-7 × 7 molecular beam epitaxy is studied using scanning tunneling microscopy (STM). A detailed analysis of the population of small amorphous clusters coexisting on the surface with epitaxial 2D islands has been performed. It is shown that small clusters tend to form pairs. The pairs serve as precursors for 2D islands as confirmed by direct STM observations of the smallest 2D islands covering two adjacent half-unit cells of the 7 × 7 reconstruction. It is proved with scaling arguments that the critical nucleus for 2D island formation consists not only of the pair itself, but also includes additional adatoms not belonging to the stable clusters.     

Adsorption dynamics of CO2 on Cu(1 1 0): A molecular beam study

Molecular beam scattering measurements have been conducted to examine the adsorption dynamics of CO₂ on Cu(1 1 0). The initial adsorption probability, S₀, decreases exponentially from 0.43 ± 0.03 to a value close to the detection limit (∼0.03) within the impact energy range of E_i = (0.12-1.30) eV. S₀ is independent of the adsorption temperature, T_s, and the impact angle, α_i, i.e., the adsorption is non-activated and total energy scaling is obeyed. The coverage, Θ, dependent adsorption probability, S(Θ), agrees with precursor-assisted adsorption dynamics (Kisliuk type) above T_s ∼ 91 K. However, below that temperature adsorbate-assisted adsorption (S increases with Θ) has been observed. That effect is most distinct at large E_i and low T_s. The S(Θ) data have been modeled by Monte Carlo simulations. No indications of CO₂ dissociation were obtained from Auger Electron Spectroscopy or the molecular beam scattering data.     

Hydroxylated α-Al2O3 (0 0 0 1) surfaces and metal/α-Al2O3 (0 0 0 1) interfaces

X-ray photoelectron spectroscopy was applied to study the hydroxylation of α-Al₂O₃ (0 0 0 1) surfaces and the stability of surface OH groups. The evolution of interfacial chemistry of the α-Al₂O₃ (0 0 0 1) surfaces and metal/α-Al₂O₃ (0 0 0 1) interfaces are well illustrated via modifications of the surface O1s spectra. Clean hydroxylated surfaces are obtained through water- and oxygen plasma treatment at room temperature. The surface OH groups of the hydroxylated surface are very sensitive to electron beam illumination, Ar⁺ sputtering, UHV heating, and adsorption of reactive metals. The transformation of a hydroxylated surface to an Al-terminated surface occurs by high temperature annealing or Al deposition.     

CO2 dissociation on Ni(2 1 1)

The direct and H-mediated dissociation of CO₂ on Ni(2 1 1) were investigated at the level of density functional theory. Although formate (HCOO) formation via CO₂ hydrogenation was widely reported for CO₂ adsorption on metal surfaces, it is found that on Ni(2 1 1) HCOO dissociation into CHO and O is much difficult, while direct dissociation of adsorbed CO₂ into CO and O is more favorable. It is also found that the degree of electron transfer from surface to adsorbed CO₂ correlates with the elongation of C-O bond lengths and the reduction of the CO₂ dissociation barrier.     

Characterization of single-crystalline In2O3 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

Epitaxial In₂O₃ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates by metalorganic chemical vapor deposition (MOCVD). The films were deposited at different substrate temperatures (450-750 °C). The film deposited at 650 °C has the best crystalline quality, and observation of the interface area shows a clear cube-on-cube epitaxial relationship of In₂O₃(1 0 0)||YSZ(1 0 0) with In₂O₃[0 0 1]||YSZ[0 0 1]. The Hall mobility of the single-crystalline In₂O₃ film deposited at 650 °C is as high as 66.5 cm² V⁻¹ s⁻¹ with carrier concentration of 1.5 × 10¹⁹ cm⁻³ and resistivity of 6.3 × 10⁻³ Ω cm. The absolute average transmittance of the obtained films in the visible range exceeds 95%.     

Formation of highly textured (1 1 1) Bi2O3 films by anodization of electrodeposited bismuth films

Highly textured bismuth oxide (Bi₂O₃) thin films have been prepared using anodic oxidation of electrodeposited bismuth films onto stainless steel substrates. The Bi₂O₃ films were uniform and adherent to substrate. The Bi₂O₃ films were characterized for their structural and electrical properties by means of X-ray diffraction (XRD), electrical resistivity and dielectric measurement techniques. The X-ray diffraction pattern showed that Bi₂O₃ films are highly textured along (1 1 1) plane. The room temperature electrical resistivity of the Bi₂O₃ films was 10⁵ Ω cm. Dielectric measurement revealed normal oxide behavior with frequency.     

CO2 adsorption on the bimetallic Zn-on-Cu(1 1 0) system

Adsorption probability measurements (molecular beam scattering) have been conducted to examine the adsorption dynamics (i.e. the gas-surface energy transfer processes) of CO₂ adsorption on the Zn-on-Cu(1 1 0) bimetallic system. The results indicate surface alloy formation, which is in agreement with prior studies. Depositing Zn at 300 K on Cu(1 1 0), above the condensation temperature of CO₂, leads to a “blocking” of CO₂ adsorption sites by Zn which is incorporated in the Cu(1 1 0) surface. This apparent site blocking effect indicates a lowering of the CO₂ binding energy on the alloyed surface as compared with the clean Cu(1 1 0) support. The Zn coverage has been calibrated by Auger electron spectroscopy and thermal desorption spectroscopy.     

The interaction of ultrathin Cr layers with SrTiO3(1 0 0)

The growth of ultrathin Cr overlayers on SrTiO₃(1 0 0) was studied by X-ray photoelectron spectroscopy, scanning tunneling microscopy, and transmission electron microscopy. It is found that the metal-oxide interaction strongly depends on the deposition temperature. At T < 600 °C, the interfaces are atomically sharp. Local charge transfer happens between the interfacial Cr adatoms and the topmost substrate atoms. The binding energy shift of Cr 2p is dominated by the final state effects. In case of T > 600 °C, bulk diffusion of oxygen in the oxide substrate may occur, which results in a redox reaction and the formation of new reaction phases at the interfaces. In this temperature regime, the binding energy shift of Cr 2p is mainly controlled by the initial state effects.     

CO2 adsorption on Cr(1 1 0) and Cr2O3(0 0 0 1)/Cr(1 1 0)

We attempt to correlate qualitatively the surface structure with the chemical activity for a metal surface, Cr(1 1 0), and one of its surface oxides, Cr₂O₃(0 0 0 1)/Cr(1 1 0). The kinetics and dynamics of CO₂ adsorption have been studied by low energy electron diffraction (LEED), Aug er electron spectroscopy (AES), and thermal desorption spectroscopy (TDS), as well as adsorption probability measurements conducted for impact energies of E_i = 0.1-1.1 eV and adsorption temperatures of T_s = 92-135 K. The Cr(1 1 0) surface is characterized by a square shaped LEED pattern, contamination free Cr AES, and a single dominant TDS peak (binding energy E_d = 33.3 kJ/mol, first order pre-exponential 1 × 10¹³ s⁻¹). The oxide exhibits a hexagonal shaped LEED pattern, Cr AES with an additional O-line, and two TDS peaks (E_d = 39.5 and 30.5 kJ/mol). The initial adsorption probability, S₀, is independent of T_s for both systems and decreases exponentially from 0.69 to 0.22 for Cr(1 1 0) with increasing E_i, with S₀ smaller by ∼0.15 for the surface oxide. The coverage dependence of the adsorption probability, S(Θ), at low E_i is approx. independent of coverage (Kisliuk-shape) and increases initially at large E_i with coverage (adsorbate-assisted adsorption). CO₂ physisorbs on both systems and the adsorption is non-activated and precursor mediated. Monte Carlo simulations (MCS) have been used to parameterize the beam scattering data. The coverage dependence of E_d has been obtained by means of a Redhead analysis of the TDS curves.     

Band offsets at the epitaxial anatase TiO2/n-SrTiO3(0 0 1) interface

We have used high-energy resolution X-ray photoelectron spectroscopy to measure valence band offsets at the epitaxial anatase TiO₂(0 0 1)/n-SrTiO₃(0 0 1) heterojunction prepared by molecular beam epitaxy. The valence band offsets range between −0.06 ± 0.05 and +0.16 ± 0.05 eV for anatase thicknesses between 1 and 8 monolayers and three different methods of substrate surface preparation, with no systematic dependence on film thickness. The conduction band offset (CBO) varies over a comparable range by virtue of the fact that anatase and SrTiO₃ exhibit the same bandgap (∼3.2 eV). In contrast, density functional theory predicts the VBO to be +0.55 eV. The lack of agreement between theory and experiment suggests that either some unknown factor in the interface structure or composition excluded from the modeling is influencing the band offset, or that density functional theory cannot accurately calculate band offsets in these oxide materials. The small experimental band offsets have important implications for the use of this interface for fundamental investigations of surface photocatalysis. Neither electrons nor holes are likely to become trapped in the substrate and thus be unable to participate in surface photocatalytic processes.     

Molecular dynamics study on surface structure and surface energy of rutile TiO2 (1 1 0)

The formula for surface energy was modified in accordance with the slab model of molecular dynamics (MDs) simulations, and MD simulations were performed to investigate the relaxed structure and surface energy of perfect and pit rutile TiO₂(1 1 0). Simulation results indicate that the slab with a surface more than four layers away from the fixed layer expresses well the surface characteristics of rutile TiO₂ (1 1 0) surface; and the surface energy of perfect rutile TiO₂ (1 1 0) surface converges to 1.801±0.001 J m⁻². The study on perfect and pit slab models proves the effectiveness of the modified formula for surface energy. Moreover, the surface energy of pit surface is higher than that of perfect surface and exhibits an upper-concave parabolic increase and a step-like increase with increasing the number of units deleted along [0 0 1] and [1 1 0], respectively. Therefore, in order to obtain a higher surface energy, the direction along which atoms are cut out should be chosen in accordance with the pit sizes: [] direction for a small pit size and [0 0 1] direction for a big pit size; or alternatively the odd units of atoms along [1 1 0] direction are removed.