Stress dependence of growth mode change of epitaxial layered cobaltite γ-Na0.7CoO2

We report stress dependence of growth characteristics of epitaxial γ-Na_0.7CoO₂ films on various substrates deposited by pulsed laser deposition method. On the sapphire substrate, the γ-Na_0.7CoO₂ thin film exhibits spiral surface growth with multi-terraces and highly crystallized texture. For the γ-Na_0.7CoO₂ thin film grown on the (1 1 1) SrTiO₃ substrate, the nano-islands of ∼30 nm diameter on the hexagonal grains are observed. These islands indicate that the growth mode changes from step-flow growth mode to Stranski-Krastanow (SK) growth mode. On the (1 1 1) MgO substrate, the large grains formed by excess adatoms covering an aperture between hexagonal grains are observed. These experimental demonstrations and controllability could provide opportunities of strain effects of Na_xCoO₂, physical properties of thin films, and growth dynamics of heterogeneous epitaxial thin films.     

Crystallization and surface morphology of Au/SiO2 thin films following furnace and flame annealing

A crystallization and surface evolution study of Au thin film on SiO₂ substrates following annealing at different temperatures above the eutectic point of the Au/Si system are reported. Samples were prepared by conventional evaporation of gold in a high vacuum (10⁻⁷ mbar) environment on substrates at room temperature. Thermal treatments were performed by both furnace and flame annealing techniques. Au thin films can be crystallized on SiO₂ substrates by both furnace and flame annealing. Annealing arranges the Au crystallites in the (1 1 1) plane direction and changes the morphology of the surface. Both, slow and rapid annealing result in a good background in the XRD spectra and hence clean and complete crystallization which depends more on the temperature than on the time of annealing. The epitaxial temperature for the Au/SiO₂ system decreases in the range of 350-400 °C. Furnace and flame annealing also form crystallized gold islands over the Au/SiO₂ surface. Relaxation at high temperatures of the strained Au layer, obtained after deposition, should be responsible for the initial stages of clusters formation. Gold nucleation sites may be formed at disordered points on the surface and they become islands when the temperature and time of annealing are increased. The growth rate of crystallites is highest around 360 °C. Above this temperature, the layer melts and gold diffuses from the substrate to the nucleation sites to increase the distance between islands and modify their shapes. Well above the eutectic temperature, the relaxed islands have hexagonally shaped borders. The mean crystallite diameters grow up to a maximum mean size of around 90 nm. The free activation energy for grain boundary migration above 360 °C is 0.2 eV. Therefore the type of the silicon substrate changes the mechanism of diffusion and growth of crystallites during annealing of the Au/Si system. Epitaxial Au(1 1 1) layers without formation of islands can be prepared by furnace annealing in the range of 300-310 °C and by flame annealing of a few seconds and up to 0.5 min.     

Scanning tunnelling microscopy studies of growth morphology in highly epitaxial c-axis oriented Pt thin film on (0 0 1) SrTiO3

A noble metal Pt thin film was successfully grown on (0 0 1) SrTiO₃ substrate by using a DC-sputtering technique. The surface morphology and growth features of the as-grown Pt films were investigated by scanning tunnelling microscopy. Growth conditions, such as pre-sputtering, deposition ambience, and oxygen ratio are found to greatly affect the orientation, the crystallinity, and the epitaxial behavior of Pt films on (0 0 1) SrTiO₃. Single-crystalline Pt films have been achieved by introducing a few percentage oxygen into the sputtering ambient. The in-plane-relationship of the c-axis oriented Pt thin films on (0 0 1) SrTiO₃ was determined to be (0 0 1)_Pt∥(0 0 1)_SrTiO3 and [0 0 1]_Pt∥[0 0 1]_SrTiO3. Oxygen in the sputtering ambient was found to be a key factor to achieve the epitaxial Pt films.     

A comparative study of fibre-textured and epitaxial Nb-doped Pb(Zr0.53Ti0.47)O3 thin films on different substrates

Fibre-textured and epitaxial Nb-doped Pb(Zr_0.53Ti_0.47)O₃ (PNZT) thin films were grown on the different substrates by a sol-gel process. The [1 0 0]- and [1 1 1]-fibre-textured polycrystalline PNZT films were obtained on platinized silicon substrates by introducing PbO and TiO₂ seeding layers, while the [0 0 1]- and [1 1 1]-oriented epitaxial PNZT films were formed directly on Nb-doped SrTiO₃ (Nb:STO) single-crystal substrates with (1 0 0) and (1 1 1) surfaces, respectively. The preferential orientation and phase structure of the fibre-textured and epitaxial PNZT films, as well as their influences on the electrical properties were investigated. Higher remnant polarization (P_r) and piezoelectric coefficient (d₃₃) were obtained for the epitaxial PNZT films on Nb:STO substrates than that for the fibre-textured ones on platinized silicon substrates. For both fibre-textured and epitaxial cases, the PNZT films with [1 0 0]/[0 0 1] orientations show higher piezoelectric responses than [1 1 1]-oriented ones, whereas better ferroelectric properties can be obtained in the latter. The intrinsic and extrinsic contributions were discussed to explain the difference in electrical properties for differently oriented fibre-textured and epitaxial PNZT films on different substrates.     

Influence of epitaxial growth on phase competition in Pr0.5Sr0.5MnO3 films

A series of Pr_0.5Sr_0.5MnO₃ (PSMO) films with various thickness were epitaxially grown on substrates of (0 0 1)-oriented (LaAlO₃)_0.3(SrAl_0.5Ta_0.5O₃)_0.7 (LSAT), LaAlO₃ (LAO) and SrTiO₃ (STO), and (0 1 1)-oriented STO using pulse laser deposition. Influence of epitaxial growth on phase competition was investigated. A ferromagnetic metal to antiferromagnetic insulator (FMM-AFI) transition upon cooling is present in both largely compressed situations deposited on LAO (0 0 1) and tensile cases deposited on STO (0 0 1) but absent in little strained films grown on LSAT (0 0 1), indicating that the antiferromagnetic insulating state is favored by strains. On the other hand, the 400 nm films deposited on (0 1 1)-oriented STO as well as LAO substrates show FMM-AFI transition. These results reveal that both the orientation of epitaxial growth and substrate-induced strain affect the FMM-AFI transition.     

Epitaxial C60 thin films on Bi(0 0 0 1)

We have used the Bi(0 0 0 1)/Si(1 1 1) template to grow highly ordered C₆₀ epitaxial thin films and analyzed them using scanning tunneling microscopy and low-energy electron microscopy. The in situ low-energy electron microscope investigations show that the initial nucleation of the C₆₀ islands on the surface takes place at surface defects, such as domain boundaries and multiple steps. The in-plane lattice parameters of this C₆₀ film turns out to be the same as that of the bulk fcc(1 1 1) C₆₀. The line-on-line epitaxial structure is realized in spite of a weak interaction between the C₆₀ molecules and Bi(0 0 0 1) surface, while scanning tunneling spectroscopy indicates that there is a negligible charge transfer between the molecules and the surface.     

Growth of β-FeSi2 thin film on textured silicon substrate for solar cell application

(2 0 2)/(2 2 0)-oriented epitaxial β-FeSi₂ thin films were deposited on textured Si (1 0 0) substrate by magnetron sputtering. The influences of thickness and annealing temperature on the β-FeSi₂ crystallization were studied to find the optimal condition. The results of surface morphology and optical property measurements showed that the inverted pyramid array in the surface of β-FeSi₂ thin films could reduce the surface reflection of β-FeSi₂. In dark condition, the β-FeSi₂/textured-Si heterojunction showed diode property with rectifying ratio of 2.89 × 10⁵ and built-in potential of 0.58 V. These results indicated the potential application of textured Si substrate in β-FeSi₂ solar cells.     

Microstructure of epitaxial SrRuO3 thin films on MgO substrates

SrRuO₃ thin films have been grown on singular (1 0 0) MgO substrates using pulsed laser deposition (PLD) in 30 Pa oxygen ambient and at a temperature of 400-700 °C. Ex situ reflection high-energy electron diffraction (RHEED) as well as X-ray diffraction (XRD) θ/2θ scan indicated that the films deposited above 650 °C were well crystallized though they had a rough surface as shown by atom force microscopy (AFM). XRD Φ scans revealed that these films were composed of all three different types of orientation domains, which was further confirmed by the RHEED patterns. The heteroepitaxial relationship between SrRuO₃ and MgO was found to be [1 1 0] SRO//[1 0 0] MgO and 45°-rotated cube-on-cube [0 0 1] SRO//[1 0 0] MgO. These domain structures and surface morphology are similar to that of ever-reported SrRuO₃ thin films deposited on the (0 0 1) LaAlO₃ substrates, and different from those deposited on (0 0 1) SrTiO₃ substrates that have an atomically flat surface and are composed of only the [1 1 0]-type domains. The reason for this difference was ascribed to the effect of lattice mismatch across the film/substrate interface. The room temperature resistivity of SrRuO₃ films fabricated at 700 °C was 300 μΩ cm. Therefore, epitaxial SrRuO₃ films on MgO substrate could serve as a promising candidate of electrode materials for the fabrication of ferroelectric or dielectric films.     

The interplay between molecular orientation, film morphology and luminescence properties of tetracene thin films on epitaxial AlOx/Ni3Al(1 1 1)

We report a systematic study of the interplay between molecular orientation, film morphology and luminescence properties of tetracene thin films on epitaxial alumina films on Ni₃Al(1 1 1), employing high resolution electron energy loss spectroscopy (HREELS), X-ray photoelectron spectroscopy (XPS), low energy electron diffraction (LEED), and photoluminescence spectroscopy (PL). If deposited at low temperatures, tetracene forms laterally disordered and compact films in which at least the first monolayer is oriented parallel to the substrate. For thicknesses in the range of 10 Å or below, these as-deposited films show no luminescence, while thicker films exhibit weak luminescence from higher layers. On annealing to 210 K, tetracene films dewet the AlO_x/Ni₃Al(1 1 1) surface and transform into an island morphology. At the same time, molecules tend to re-orient into a more upright configuration. In this island configuration, even thin films show luminescence. We can thus conclude that in spite of the insulating nature of the surface, the interaction of flat-lying tetracene molecules with AlO_x/Ni₃Al(1 1 1) is strong enough to provide at least one efficient non-radiative decay channel.     

Thickness-dependent surface morphology of La0.9Sr0.1MnO3 ultrathin films

La_0.9Sr_0.1MnO₃ (LSMO) ultrathin films with various thickness (in the range of 5-50 unit cells) are grown on (0 0 1) substrates of the single-crystal SrTi_0.99Nb_0.01O₃ by laser molecular-beam epitaxy (laser-MBE), and the surface morphology of these films were measured by scanning tunneling microscopy (STM). STM images of LSMO ultrathin film surface reveal that surface morphology becomes more flat with increasing film thickness. This study highlights the important effect of strain caused by the lattice mismatch between substrates and ultrathin films. And the results should be useful to the investigations on growing manganite perovskite materials.     

The ferroelectric and ferromagnetic characterization of CoFe2O4/Pb(Mg1/3Nb2/3)O3-PbTiO3 multilayered thin films

The multiferroic (PMN-PT/CFO)_n (n = 1,2) multilayered thin films have been prepared on SiO₂/Si(1 0 0) substrate with LNO as buffer layer via a rf magnetron sputtering method. The structure and surface morphology of multilayered thin films were determined by X-ray diffraction (XRD) and atom force microscopy (AFM), respectively. The smooth, dense and crack-free surface shows the excellent crystal quality with root-mean-square (RMS) roughness only 2.9 nm, and average grain size of CFO thin films on the surface is about 44 nm. The influence of the thin films thickness size, periodicity n and crystallite orientation on their properties including ferroelectric, ferromagnetic properties in the (PMN-PT/CFO)_n multilayered thin films were investigated. For multilayered thin films with n = 1 and n = 2, the remanent polarization Pr are 17.9 μC/cm² and 9.9 μC/cm²; the coercivity H_c are 1044 Oe and 660 Oe, respectively. In addition, the relative mechanism are also discussed.     

Epitaxial growth of InN on nearly lattice-matched (Mn,Zn)Fe2O4

We have grown InN films on nearly lattice-matched (Mn,Zn)Fe₂O₄ (111) substrates at low temperatures by pulsed laser deposition (PLD) and investigated their structural properties. InN films grown at substrate temperatures above 400 °C show poor crystallinity, and their in-plane epitaxial relationship is [10-10]InN//[11-2](Mn,Zn)Fe₂O₄, which means that their lattice mismatch is quite large (11%). By contrast, high quality InN films with flat surfaces can be grown at growth temperatures lower than 150 °C with the ideal in-plane epitaxial relationship of [11-20]InN//[11-2](Mn,Zn)Fe₂O₄, which produces lattice mismatches of as low as 2.0%. X-ray reflectivity measurements have revealed that the thickness of the interfacial layer between the InN and the substrates is reduced from 14 to 8.4 nm when the growth temperature is decreased from 400 °C to room temperature. This suppression of the interface reactions by reducing the growth temperature is probably responsible for the improvement in crystalline quality. These results indicate that the use of (Mn,Zn)Fe₂O₄ (111) substrates at low growth temperatures allows us to achieve nearly lattice matched epitaxial growth of InN.     

Influence of the laser wavelength on the epitaxial growth and electrical properties of La0.8Sr0.2MnO3 films grown by excimer laser-assisted MOD

Epitaxial La_1−xSr_xMnO₃ (LSMO) films were prepared by excimer laser-assisted metal organic deposition (ELAMOD) at a low temperature using ArF, KrF, and XeCl excimer lasers. Cross-section transmission electron microscopy (XTEM) observations confirmed the epitaxial growth and homogeneity of the LSMO film on a SrTiO₃ (STO) substrate, which was prepared using ArF, KrF, and XeCl excimer lasers. It was found that uniform epitaxial films could be grown at 500 °C by laser irradiation. When an XeCl laser was used, an epitaxial film was formed on the STO substrate at a fluence range from 80 to 140 mJ/cm² of the laser fluence for the epitaxial growth of LSMO film on STO substrate was changed. When the LaAlO₃ (LAO) substrate was used, an epitaxial film was only obtained by ArF laser irradiation, and no epitaxial film was obtained using the KrF and XeCl lasers. When the back of the amorphous LSMO film on an LAO substrate was irradiated using a KrF laser, no epitaxial film formed. Based on the effect of the wavelength and substrate material on the epitaxial growth, formation of the epitaxial film would be found to be photo thermal reaction and photochemical reaction. The maximum temperature coefficient of resistance (TCR) of the epitaxial La_0.8Sr_0.2MnO₃ film on an STO substrate grown using an XeCl laser is 4.0%/K at 275 K. XeCl lasers that deliver stabilized pulse energies can be used to prepare LSMO films with good a TCR.     

Morphology and growth modes of metal-oxides deposited on SrTiO3

Classical molecular dynamics simulations are used to examine the growth of SrO and TiO₂ thin films on SrTiO₃ (STO). In particular, the simulations consider the deposition of SrO and TiO₂ molecules at incident energies of 0.1, 0.5, and 1.0 eV/atom onto the (0 0 1) surface of STO. The role of surface termination layer (SrO vs. TiO₂) is analyzed. In the case of SrO deposition, smooth, ordered films are produced for all incident energies considered and for both surface terminations. By contrast, in the case of TiO₂ deposition, three-dimensional islands are formed under all conditions. These predictions are in good agreement with experimental data. Importantly, the simulations explain why these differing morphologies are produced for SrO and TiO₂ deposition.     

Electrical behavior of BaZr0.1Ti0.9O3 and BaZr0.2Ti0.8O3 thin films

BaZr_0.1Ti_0.9O₃ and BaZr_0.2Ti_0.8O₃ (BZT) thin films were deposited on Pt/Ti/LaAlO₃ (1 0 0) substrates by radio-frequency magnetron sputtering, respectively. The films were further annealed at 800 °C for 30 min in oxygen. X-ray diffraction θ-2θ and Φ-scans showed that BaZr_0.1Ti_0.9O₃ films displayed a highly (h 0 0) preferred orientation and a good cube-on-cube epitaxial growth on the LaAlO₃ (1 0 0) substrate, while there are no obvious preferential orientation in BaZr_0.2Ti_0.8O₃ thin films. The BaZr_0.1Ti_0.9O₃ films possess larger grain size, higher dielectric constant, larger tunability, larger remanent polarization and coercive electric field than that of BaZr_0.2Ti_0.8O₃ films. Whereas, BaZr_0.1Ti_0.9O₃ films have larger dielectric losses and leakage current density. The results suggest that Zr⁴⁺ ion can decrease dielectric constant and restrain non-linearity. Moreover, the enhancement in dielectric properties of BaZr_0.1Ti_0.9O₃ films may be attributed to (1 0 0) preferred orientation.     

Solid phase epitaxy of Ge films on CaF2/Si(1 1 1)

At room temperature deposited Ge films (thickness < 3 nm) homogeneously wet CaF₂/Si(1 1 1). The films are crystalline but exhibit granular structure. The grain size decreases with increasing film thickness. The quality of the homogeneous films is improved by annealing up to 200 °C. Ge films break up into islands if higher annealing temperatures are used as demonstrated combining spot profile analysis low energy electron diffraction (SPA-LEED) with auger electron spectroscopy (AES). Annealing up to 600 °C reduces the lateral size of the Ge islands while the surface fraction covered by Ge islands is constant. The CaF₂ film is decomposed if higher annealing temperatures are used. This effect is probably due to the formation of GeF_x complexes which desorb at these temperatures.     

Structural evolution and epitaxial stabilisation of pulsed laser deposited Sm0.55Nd0.45NiO3 solid solution nanostructured films on undoped Si (1 0 0) and NdGaO3 substrates

We report on the effects of substrate, ambient oxygen pressure and deposition time on the crystal structure, and morphology of Sm_0.55Nd_0.45NiO₃ solid solution nanostructured films synthesized by pulsed-laser deposition. In each film the structure was found to be consistent with a perovskite structure with preferential planes growth and reveals a strong orientation along the orthorhombic (2 1 0) plane of the perovskite subcell for the film deposited on NdGaO₃ where highly crystalline films were obtained within 15 min deposition time with a low surface roughness of 8.79 nm. Similar structure is observed on Si (1 0 0) substrate only at O₂ pressure of 0.4 mbar. The surface morphology of the different samples shows a net dense film structure with several droplets population. The nano-scaled droplets are in general spherical in shape; a detailed analysis indicates that the laser ablation of this nickelate family is governed to a certain extent by a heat transfer phenomenon.     

Epitaxial growth of Ba8Ga16Ge30 clathrate film on Si substrate by RF helicon magnetron sputtering with evaluation on thermoelectric properties

Epitaxial Ba₈Ga₁₆Ge₃₀ clathrate thin films were successfully grown on Si substrate by using helicon magnetron sputtering. The (1 0 0) lattice of Ba₈Ga₁₆Ge₃₀ was identified grown on four Si(2 0 0) lattices in small mismatch (0.1%). Both the color of samples and XRD results suggest 600 °C is the optimal substrate temperature for the growth of high quality Ba-Ga-Ge clathrate film on Si substrates. High Seebeck coefficients and electrical resistivities for the deposited clathrate thin films in comparison with those of bulk are obtained. The high crystal quality and thermionic effects in heterostructures may contribute to the larger Seebeck coefficients, while the increasing of interface scattering for electrons probably is the reason for large electrical resistivities. Although the thermoelectric (TE) results are not ideal as designed, our results are significant due to the first successful work on epitaxial growth of Ba₈Ga₁₆Ge₃₀ clathrate thin films on Si substrate with large Seebeck coefficient.     

Epitaxial growth of Au and Pt on Fe3O4(1 1 1) surface

We have studied the epitaxial growth of Au and Pt layers on Fe₃O₄(1 1 1) as a function of the deposition temperature and thickness. The layers were deposited by UHV sputtering and the structural properties were investigated by reflection high energy electron diffraction (RHEED), X-ray experiments and transmission electron microscopy (TEM). The epitaxial growth of both metals was obtained whatever the deposition conditions but the wetting is however different for the two metals. Comparison between the coverage ratios of Au and Pt is correlated with their surface and interfaces energies. The optimum conditions to achieve a 2D flat epitaxial metallic layer are determined.     

Epitaxial growth and structural characterization of Pb(Fe1/2Nb1/2)O3 thin films

We have grown lead iron niobate thin films with composition Pb(Fe_1/2Nb_1/2)O₃ (PFN) on (0 0 1) SrTiO₃ substrates by pulsed laser deposition. The influence of the deposition conditions on the phase purity was studied. Due to similar thermodynamic stability spaces, a pyrochlore phase often coexists with the PFN perovskite phase. By optimizing the kinetic parameters, we succeeded in identifying a deposition window which resulted in epitaxial perovskite-phase PFN thin films with no identifiable trace of impurity phases appearing in the X-ray diffractograms. PFN films having thicknesses between 20 and 200 nm were smooth and epitaxially oriented with the substrate and as demonstrated by RHEED streaks which were aligned with the substrate axes. X-ray diffraction showed that the films were completely c-axis oriented and of excellent crystalline quality with low mosaicity (X-ray rocking curve FWHM?0.09°). The surface roughness of thin films was also investigated by atomic force microscopy. The root-mean-square roughness varies between 0.9 nm for 50-nm-thick films to 16 nm for 100-nm-thick films. We also observe a correlation between grain size, surface roughness and film thickness.