Van der Pauw resistivity measurements on evaporated thin films of cadmium arsenide, Cd3As2

Cadmium arsenide is a II-V semiconductor, exhibiting n-type intrinsic conductivity with high mobility and narrow bandgap. It is deposited by thermal evaporation, and has shown the Schottky and Poole-Frenkel effects at high electric fields, but requires further electrical characterisation. This has now been extended to low-field van der Pauw lateral resistivity measurements on films of thickness up to 1.5 μm. Resistivity was observed to decrease with increasing film thickness up to 0.5 μm from about 3 × 10⁻³ Ω m to 10⁻⁵ Ω m, where the crystalline granular size increases with film thickness. This decrease in resistivity was attributed to a decrease in grain boundary scattering and increased mobility. Substrate temperature during deposition also influenced the resistivity, which decreased from around 10⁻⁴ Ω m to (10⁻⁵ to 10⁻⁶) Ω m for an increase in substrate deposition temperature from 300 K to 423 K. This behaviour appears to result from varying grain sizes and ratios of crystalline to amorphous material. Resistivity decreased with deposition rate, reaching a minimum value at about 1.5 nm s⁻¹, before slowly increasing again at higher rates. It was concluded that this resulted from a dependence of the film stoichiometry on deposition rate. The dependence of resistivity on temperature indicates that intercrystalline barriers dominate the conductivity at higher temperatures, with a hopping conduction process at low temperatures.     

Electron emission characteristics of Al-AlN granular films

An electron conduction emitter of Al-AlN granular films was proposed for surface conduction electron emission device in this paper. The Al-AlN granular films with thickness of 30 nm were prepared between two co-planar electrodes with gap of 10 μm by magnetron sputtering. After electroforming the Al-AlN granular films, the films’ structure could be recovered by applying the periodic device voltage (V_f). Stable and uniform electron emission was observed with turn-on voltage of 5.3 V and threshold voltage of 9 V. The emitter emission current (I_e) of 4.84 μA for 36 cells was obtained with the anode voltage of 2.5 kV and the device voltage of 12 V. In addition, Fowler-Nordheim plots for I_e-V_f properties showed that the electron emission mechanism should be field emission.     

A kinetic study of the thermal decomposition process of potassium metabisulfite: Estimation of distributed reactivity model

The thermal decomposition kinetics of potassium metabisulfite was studied by thermogravimetric (TG) and differential thermogravimetric (DTG) techniques using non-isothermal experiments. The apparent activation energy (E_a) is determined using the differential (Friedman) isoconversional method. The results of the Friedman's isoconversional analysis of the TG data suggests that the investigated decomposition process follows a single-step reaction and the observed apparent activation energy was determined as 122.4±2.1 kJ mol⁻¹. A kinetic rate equation was derived for the decomposition process of potassium metabisulfite with contracting area model, f(α)=2(1−α)^1/2, which is established using the Malek's kinetic procedure. The value of pre-exponential factor (A) is also evaluated and was found to be A=1.37×10¹² min⁻¹. By applying the Miura's procedure the distributed reactivity model (DRM) for investigated decomposition process was established. From the dependence α versus E_a, the experimental distribution curve of apparent activation energies, f(E_a), was estimated. By applying the non-linear least-squares analysis, it was found that the Gaussian distribution model (with distribution parameters E₀=121.3 kJ mol⁻¹ and σ=1.5 kJ mol⁻¹) represents the best reactivity model for describing the investigated process. Using the Miura's method, the A values were estimated at five different heating rates and the average A values are plotted against E_a. The linear relationship between the A and E_a values was established (compensation effect). Also, it was concluded that the E_a values calculated by the Friedman's method and estimated distribution curve, f(E_a), are correct even in the case when the investigated decomposition process occurs through the single-step reaction mechanism.     

Calculation of the surface energy of bcc transition metals by using the second nearest-neighbor modified embedded atom method

The surface energies for 24 surfaces of all bcc transition metals Fe, Cr, Mo, W, V, Nb and Ta have been calculated by using the second nearest-neighbor modified embedded atom method. The results show that, for all bcc transition metals, the order among three low-index surface energies E_(1 1 0) < E_(1 0 0) < E_(1 1 1) is in agreement with experimental results and E_(1 1 0) is also the lowest surface energy for various surfaces. So that from surface energy minimization, the (1 1 0) texture should be favorable in the bcc films. This is also consistent with experimental results. The surface energy for the other surfaces increases linearly with increasing angle between the surfaces (h k l) and (1 1 0). Therefore, a deviation of a surface orientation from (1 1 0) can be used to estimate the relative values of the surface energy.     

Characterization of defects introduced in Sb doped Ge by 3 keV Ar sputtering using deep level transient spectroscopy (DLTS) and Laplace-DLTS (LDLTS)

We have used deep level transient spectroscopy (DLTS), and Laplace-DLTS to investigate the defects created in antimony doped germanium (Ge) by sputtering with 3 keV Ar ions. Hole traps at E_V+0.09 eV and E_V+0.31 eV and an electron trap at E_C−0.38 eV (E-center) were observed soon after the sputtering process. Room temperature annealing of the irradiated samples over a period of a month revealed a hole trap at E_V+0.26 eV. Above room temperature annealing studies revealed new hole traps at E_V+0.27 eV, E_V+0.30 eV and E_V+0.40 eV.     

Thermoelectric power and phase transition of polycrystalline As2Te3 under pressure

The pressure dependence of the thermoelectric power of monoclinic As₂Te₃ is measured up to 10 GPa using a Mao-Bell diamond anvil cell. The thermoelectric power never reaches an absolute value greater than the ambient pressure value of 242 μV/K. Evidence of a phase transition is present between 6 and 8 GPa where the thermoelectric power reaches an absolute value of 225 μV/K after passing through a minimum of S≈75 μV/K. X-ray diffraction experiments confirm that the resulting structure is β-As₂Te₃, which is isostructural with Bi₂Te₃ and Sb₂Te₃.     

Observation by ICLAS VeCSEL technique, and rotational analysis, of the ΔvGeH=5 stretching vibrational overtone of H3GeD

The fourth GeH stretching overtone band of monoisotopic H₃⁷⁰GeD at 9877 cm⁻¹ has been recorded by ICLAS VeCSEL technique with a path length equivalent to 26 km. The (500 A₁/E) band has been observed and rotationally analyzed up to J^′=18. The band was shown to be essentially unperturbed except some high J states. The assigned transitions were fitted, with σ(Fit) ca. 6.5 × 10⁻³ cm⁻¹. While eight refined parameters were needed up to J^′_max=14, six quartic centrifugal distortion constants were refined in addition for the larger body of 829 data with J^′_max=18. The (500 A₁/E) parameters of H₃⁷⁰GeD perfectly fulfill the theoretical relations valid at the local mode limit, and they fit into the series for other (n00 A₁/E) levels (n=2, 3, 6, 7, and 8). A transition moment ratio M(A₁):M(E)=0.25 was found to be in best agreement with the observed spectrum, only high J (J^′?13) transitions being evidently sensitive to this ratio.     

Electronic structure and magnetic properties of the compound CeCuIn

Magnetization, magnetic susceptibility, electrical resistivity, thermoelectric power and X-ray photoemission measurements were performed on a polycrystalline sample of CeCuIn. This compound crystallizes in a hexagonal structure of the ZrNiAl type. The magnetic data indicate that CeCuIn remains paramagnetic down to 1.9 K with a paramagnetic Curie temperature of −13 K and an effective magnetic moment equal to 2.5 μ_B. The electrical resistivity has metallic character, yet in the entire temperature range studied here, it is a strongly nonlinear function of temperature. The temperature dependence of the thermoelectric power is dominated by a small positive maximum near 76 K and a deep negative minimum at about 16 K. Above 150 K the thermopower exhibits a Mott's type behavior. The positive sign of the Seebeck coefficient in this temperature region indicates that the holes are dominant charge and heat carriers. The structure of Ce 3d_5/2 and Ce 3d_3/2 XPS spectra has been interpreted in terms of the Gunnarsson-Schönhammer theory. Three final-state contributions f⁰, f¹ and f² are clearly observed, which exhibit a spin-orbit splitting Δ_SO≈18.7 eV. The appearance of the 3d⁹f⁰ component is a clear evidence of the intermediate valence behavior of Ce. From the intensity ratio I(f⁰)/[I(f⁰)+I(f¹)+I(f²)] the 4f-occupation number is estimated to be 0.95. In turn, the ratio I(f²)/[I(f¹)+I(f²)]=0.08 yields a measure of the hybridization energy that is equal to 45 meV.     

Eigenvalues, eigenfunctions, and surface states in finite periodic systems

Using a simple approach that requires neither the Bloch functions nor the reciprocal lattice, new, compact, and rigorous analytical formulas are derived for an accurate evaluation of resonant energies, resonant states, energy eigenvalues and eigenfunctions of open and bounded n-cell periodic systems with arbitrary 1D potential shapes, provided the single cell transfer matrix is given. These formulas are applied to obtain the energy spectra and wave functions of a number of simple but representative open and bounded superlattices. We solve the fine structure in bands and exhibit unambiguously that the true eigenfunctions do no not fulfill the periodicity property |Ψ_μ,ν (z + l_c)|² = |Ψ_μ,ν (z)|², with l_c the single cell length. We show that the well known surface states and surface energy levels come out naturally. We analyze the surface repulsion effect and calculate exactly the surface energy levels for different potential discontinuities an the ends.     

New observation and analysis of the E(4)Σ state in NaLi

Polarization labeling spectroscopy is applied to study the excited E(4)¹Σ⁺ state of NaLi in the energy range 25 850-27 750 cm⁻¹ above the bottom of the ground state. The potential curve of the E state is constructed using the Inverted Perturbation Approach method.     

The CΠu state of Na2 revisited: A comprehensive study by polarization labeling spectroscopy technique

This paper contains the analysis of the C(2)¹Π_u state of Na₂ molecule based on a large data set (3030 lines) obtained from a polarization labeling spectroscopy experiment on the transition. The energies of rovibrational levels in the C state, spanning a wide range of v (0 ? v ? 43) and J (12 ? J ? 100) quantum numbers, are fitted to a Dunham polynomial expansion and also to a numerical potential curve constructed by the inverted perturbation approach (IPA) method.     

DC conductivity of silver vanadium tellurite glasses

The mixed electronic-ionic conduction in 0.5[xAg₂O-(1−x)V₂O₅]-0.5TeO₂ glasses with x=0.1-0.8 has been investigated over a wide temperature range (70-425 K). The mechanism of dc conductivity changes from predominantly electronic to ionic within the 30?mol% Ag₂O?40 range; it is correlated with the underlying change in glass structure. The temperature dependence of electronic conductivity has been analyzed quantitatively to determine the applicability of various models of conduction in amorphous semiconducting glasses. At high temperature, T>θ_D/2 (where θ_D is the Debye temperature) the electronic dc conductivity is due to non-adiabatic small polaron hopping of electrons for 0.1?x?0.5. The density of states at Fermi level is estimated to be N(E_F)≈10¹⁹-10²⁰ eV⁻¹ cm⁻³. The carrier density is of the order of 10¹⁹ cm⁻³, with mobility ≈2.3×10⁻⁷-8.6×10⁻⁹ cm² V⁻¹ s⁻¹ at 300 K. The electronic dc conductivity within the whole range of temperature is best described in terms of Triberis-Friedman percolation model. For 0.6?x?0.8, the predominantly ionic dc conductivity is described well by the Anderson-Stuart model.     

Electrical properties of KTiOPO4 single crystal in the temperature range from −100 °C to 100 °C

The electrical property of a KTiOPO₄ single crystal was studied by means of a dielectric spectroscopy method in the temperature range from −100 to 100 °C. Dielectric dispersion began at a temperature, T_S=−80 °C. It is believed that this dielectric dispersion is related to the ionic hopping conduction, which arises mainly from the jumping of K⁺ ions. The activation energy concerned with hopping conduction is E_a∼0.20 eV above T_S. T_S=−80 °C can be the minimum temperature for the hopping K⁺ ion.     

Electrical and electromechanical properties of lead-potassium-yttrium-niobate ceramics—piezoelectric applications

Tungsten bronze (TB)-type oxide ceramic Pb_0.74K_0.13Y_0.13Nb₂O₆ (PKYN) has been synthesized by the standard solid state reaction method. Single phase formation, orthorhombic crystal structure was confirmed by X-ray diffraction (XRD). The substitution of Y³⁺ in Pb_0.74K_0.52Nb₂O₆ (PKN) decreased the unit cell volume and T_C=260 °C. PKYN exhibited the remnant polarization, P_r=8.5 μC/cm², and coercive field, E_c=28.71 kV/cm. Electrical spectroscopy studies were carried out over the temperature (35-595 °C) and frequency (45 Hz-5 MHz) ranges, and the charge carrier phenomenon, grain-grain boundary contribution and non-Debye-type relaxation were analyzed. The relaxation species are immobile charges in low temperature and oxygen vacancies at higher temperature. The theoretical values computed using the relations, ε′=ε_∞+sin(n(T)π/2)(a(T)/ε₀)(ω^n(T)−1); σ(ω)=σ_dc+Aωⁿ are fitted with the experimental one. The n and A parameters suggested that the charge carrier's couple with the soft mode and become mobile at T_C. The activation enthalpy, H_m=0.38 eV, has been estimated from the hopping frequency relation ω_p=ω_e exp(−H_m/k_BT). The piezoelectric constants K_t=35.4%, d₃₃=69×10⁻¹² C/N, d₃₁=−32×10⁻³ mV/N, S₁₁^E=17.8 pm²/N, etc., achieved in PKYN indicate the material is interesting for transducer applications. The activation energies from different formalisms confirmed the ionic-type conduction.     

Multifractal analysis of ITO thin films prepared by electron beam deposition method

In this work, we developed the multifractality and its formalism to investigate the surface topographies of ITO thin films prepared by electron beam deposition method for various annealing temperatures from their atomic force microscopy (AFM) images. Multifractal analysis shows that the spectrum width, Δα (Δα = α_max − α_min), of the multifractal spectra, f(α), can be used to characterize the surface roughness of the ITO films quantitatively. Also, it is found that the f(α) shapes of the as-deposited and annealed films remained left hooked (that is Δf = f(α_min) − f(α_max) > 0), and falls within the range 0.149-0.677 depending upon the annealing temperatures.     

The peculiarities of the low-energy ion scattering by polycrystal targets

In the present work, experimental and computer simulation studies of low-energy (E₀ = 80-500 eV) Cs⁺ ions scattering on Ta, W, Re target surfaces and K⁺ ions scattering on Ti, V, Cr target surfaces have been performed for more accurate definition of mechanism of scattering, with a purpose of evaluation of an opportunity of use of slow ions scattering as a tool of surface layers analysis. The choice of the targets was based on the fact that the ratios of atomic masses of target atoms and ions μ = m₂/m₁ were almost the same for all cases considered and greater than 1 (direct mass ratio) however, the difference of binding energies of target atoms in the cases of Cs⁺ and K⁺ scattering was almost twice as much. It has been noticed that the dependencies of the relative energy retained by scattering ions at the maximum of energy distribution versus the initial energy E_m/E₀ (E₀) have a similar shape in all cases. The relative energy retained by scattering ions increases while the initial energy of incidence ions decreases. The curves are placed above each other relative to the binding energies of target atoms, to show what this says about the influence of binding energy on a process of scattering of low-energy ions. The correlation between value of energy change maintained by an ion for different values of E₀ in the case of scattering by targets with different masses of atoms and its binding energies is experimentally established. The contrary behavior of the E_m/E₀ (E₀) dependencies concerning the target atom binding energy quantity E_b for cases with direct (μ > 1) and inverse (μ < 1) mass ratio of colliding particles is established. The comparison of experimental energy distributions with calculated histograms shows that the binary collision approximation cannot elucidate the abnormally great shift in the maxima of relative energy distributions towards greater energy retained by scattering ions.     

Thermoelectric properties of the Bi2−xYxRu2O7 (x=0-2) pyrochlores

Electrical conductivity and Seebeck coefficient for the Bi_2−xY_xRu₂O₇ pyrochlores with x=0.0,0.5,1.0,1.5,2.0 were measured in the temperature range of 473-1073 K in air. With increasing Bi content, the temperature dependence of the electrical conductivity changed from semiconducting to metallic. The signs of the Seebeck coefficient were positive in the measured temperature range for all the samples, indicating that the major carriers were holes. The temperature dependence of the Seebeck coefficient for the Y₂Ru₂O₇ indicated the thermal activation-type behavior of the holes, while that for the Bi_2−xY_xRu₂O₇ with x=0.0-1.5 indicated the itinerant behavior of the holes. The change in the conduction behavior from semiconductor to metal with increasing Bi content is consistent with the increase in the overlap between the Ru4d t_2g and O2p orbitals, but the mixing of Bi6s, 6p states at E_F may not be ruled out. The thermoelectric power factors for the Bi_2−xY_xRu₂O₇ with x=1.5 and 2.0 were lower than 10⁻⁵ W m⁻¹ K⁻² and those with x=0.0,0.5,1.0 were around 1-3×10⁻⁵ W m⁻¹ K⁻².     

Effect of sulfur additive on density of localized states in nanostructures chalcogenide Se95−xSxZn5 thin films

This paper reports the measurement of space charge limited conduction (SCLC) on the fabricated thin films of Se_95−xS_xZn₅ (0.2≤x≤10) in temperature range 313–353 K for the first time. At high electric fields (E∼10⁴ V/cm), the current could be fitted into the theory of space charge limited conduction, in case of uniform distribution of localized states in mobility gap. The homogeneity and surface morphology of thin films were assessed by scanning electron microscopy. The crystalline nature of the thin films was confirmed by powder XRD and the crystallite size was calculated using Scherer's formula. The crystallite size and density of localized states were found to increase with the increase of sulfur concentration. DC conductivity and activation energy were calculated and found to decrease and increase respectively, with the increase of sulfur concentration.     

Effect of kink-rounding barriers on step edge fluctuations

The effect that an additional energy barrier E_kr for step adatoms moving around kinks has on equilibrium step edge fluctuations is explored using scaling arguments and kinetic Monte Carlo simulations. When mass transport is through step edge diffusion, the time correlation function of the step fluctuations behaves as C(t)=A(T)t^1/4. At low temperatures the prefactor A(T) shows Arrhenius behavior with an activation energy (E_det+3?)/4 if E_kr<? and (E_det+E_kr+2?)/4 if E_kr>?, where ? is the kink energy and E_det is the barrier for detachment of a step adatom from a kink. We point out that the assumption of an Einstein relation for step edge diffusion has lead to an incorrect interpretation of step fluctuation experiments, and explain why such a relation does not hold. The theory is applied to experimental results on Pt(1 1 1) and Cu(1 0 0).