Electrical transport behavior of La0.67Ca0.33MnO3/Fe3O4 composites

The influence of Fe₃O₄ contents on the electrical transport properties (resistivity and ac susceptibility) of a series of composite samples of La_0.67Ca_0.33MnO₃/Fe₃O₄ is studied. Results show that the Fe₃O₄ phase not only shifts the intrinsic insulator-metal (I-M) transition temperature T_P1 to a lower temperature, but also causes a new I-M transition at a lower temperature T_P2 (T_P2<T_P1). On the basis of an analysis by scanning electron microscopy and X-ray diffraction, we suggest that the decrease of the I-M transition temperature and the formation of the new I-M transition are caused by the segregation of a new phases related to the Fe₃O₄ at grain boundaries or surfaces of the La_0.67Ca_0.33MnO₃ grains.     

Magnetoresistance and transport properties of different impurity doped La0.67Ca0.33MnO3 composite

An enhanced magnetoresistance and a two-fold effect result from impurity dopant were observed in composites of La_0.67Ca_0.33MnO₃/YSZ and La_0.67Ca_0.33MnO₃/Fe₃O₄. Where YSZ represents yttria-stabilized zirconia and the doping level of both YSZ and Fe₃O₄ is 1 mol%. Different electrical and magnetic transport properties, in particular a lower field magnetization behavior, were observed between pure La_0.67Ca_0.33MnO₃ and the impurity doped La_0.67Ca_0.33MnO₃ composites. Compared with pure La_0.67Ca_0.33MnO₃, a possible interpretation is presented by considering the influences of YSZ and Fe₃O₄ on the structure of grain boundaries and/or surfaces of La_0.67Ca_0.33MnO₃grains.     

Large room temperature magnetoresistance in YSZ doped La0.67Ba0.33MnO3 composite

The temperature dependence of the resistivity for composite samples of (1−x)La_0.67Ba_0.33MnO₃+xYSZ(LBMO/YSZ) with different YSZ doping level of x has been investigated in a magnetic field range of 0-7000 Oe, where the YSZ represents yttria-stabilized zirconia (8 mol% Y₂O₃+92 mol% ZrO₂). With increasing YSZ doping level, the range of 0-10%, the metal-insulator transition temperature (T_P) decreases. However, the resistivity, specially the low temperature resistivity, increases. Results also show that the YSZ doping level has an important effect on a low field magnetoresistance (LFMR). In the magnetic field of 7000 Oe, a room temperature magnetoresistance value of 20% was observed for the composite with a YSZ doping level of 2%, which is encouraging for potential application of CMR materials at room temperature and low field.     

Double-peak resistivity transport properties of La0.67Ca0.33MnO3 ceramics

Polycrystalline samples of La_0.67Ca_0.33MnO₃ were prepared by solid-state reactions by varying the pelletization force and the sintering temperature. Lowering the sintering temperature gave rise to smaller grains and increased the overall resistivity of the ceramic. Partial melting was observed in the ceramics sintered at higher temperatures (1400-1500 °C). Additionally, these ceramics showed two distinct resistivity peaks. The resistivity peak near the magnetic transition (T_C) was sharp, whereas the second peak was a broad one observed below T_C.     

Thickness dependence of electroresistance in La0.67Ca0.33MnO3 epitaxial films

The electroresistance (ER) of La_0.67Ca_0.33MnO₃ (LCMO) epitaxial thin films with different thicknesses was studied. For the 110 nm thick LCMO film, its ER shows a maximum at T_p, where the resistance shows a peak, and decreases to zero at lower temperatures. While for the 30 nm thick LCMO film, its ER is remarkable in a wide temperature range. Another interesting observation in this work is that the electric current can tune the magnetoresistance of the ultrathin LCMO thin film. The results were discussed by considering the coexistence of ferromagnetic metallic phase with the charge ordered phase, and the variation of the phase separation with film thickness and electric current. This work also demonstrates that electric current can tune the magnetoresistance of the manganites, which is helpful for their applications.     

Twin-microstructure enhanced magnetoresistance in La0.67Ba0.33MnO3 oxides

The grain growth dependence of microstructure and its effects on magnetic and transport properties are studied in the polycrystalline La_0.67Ba_0.33MnO₃ oxides. It is found that a lateral growth manner along a certain direction and a concentric terrace pattern along three orthogonal axes occur in the samples sintered at 1573 and 1673 K, respectively. Lamella-like twin microstructure forms in the concentric terrace growth pattern and the magnetoresistance properties can be enhanced by the twin microstructure. It suggests that the twin-boundaries in twin-grains may possibly induce spin-dependent scattering of electrons that is field reduced, or spin-polarized tunneling of electrons that is field enhanced, thus strengthening the effect of grain boundaries.     

Enhancing low-field magnetoresistance of La0.67Ca0.33MnO3 films deposited on anodized aluminium-oxide membranes

In this paper we report a new method to fabricate nanostructured films, La0.67Ca0.33MnO3 （LCMO） nanostructured films have been fabricated by using pulsed electron beam deposition （PED） on anodized aluminium oxide （AAO） membranes, The magnetic and electronic transport properties are investigated by using the Quantum Design physics properties measurement system （PPMS） and magnetic properties measurement system （MPMS）. The resistance peak temperature （Tp） is about 85 K and the Curie temperature （To） is about 250 K for the LCMO film on an AAO membrane with a pore diameter of 20nm. Large magnetoresistance ratio （MR） is observed near Tp. The MR is as high as 85% under 1 T magnetic field. The great enhancement of MR at low magnetic fields could be attributed to the lattice distortion and the grain boundary that are induced by the nanopores on the AAO membrane.     

Magnetotransport properties of La0.67Ca0.33MnO3//La0.67Sr0.33MnO3 bilayers

The perovskite bilayers La0.67Ca0.33MnO3 （LCMO） （100 nm） / La0.67Sr0.33MnO3（LSMO） （100 nm） and LSMO （100 nm） / LCMO （100 nm） are fabricated by a facing-target sputtering technique. Their transport and magnetic properties are investigated. It is found that the transport properties between them are different obviously due to distinguishable structures, and the different lattice strains in both films result in the difference of metal-to-insulator transition. Only single-step magnetization loop appears in our bilayers from 5K to 320K, and the coercive force of LSMO/LCMO varies irregularly with a minimum ～ 2387A/m which is lower than that of LCMO and LSMO single layer films. The behaviour is explained by some magnetic coupling.     

Large enhancement of room temperature magnetoresistance in Ag-added La0.67(Ca0.65Ba0.35)0.33MnO3

The electrical and magnetoresistant properties of La_0.67(Ca_0.65Ba_0.35)_0.33MnO₃/Ag_x (abbreviated by LCBMO/Ag_x) have been studied. The results show that Ag addition causes a decrease of resistivity dramatically and especially induces a large enhancement of room temperature magnetoresistance (MR). The room temperature MR ratio for x=0.27 sample in 10 kOe magnetic field is 41%, almost 20 times larger than that for x=0 sample. This enhancement is related to that the Curie temperature (T_c) of the sample is near room temperature, as well as the significant reduction of resistivity. The good fits of experimental results for x=0.27 sample to Brillouin function indicate that the MR behavior in the Ag added LCBMO is induced by the spin-dependent hopping of the electrons between the spin clusters, which is an intrinsic property of the CMR materials.     

Enhancement of magnetoresistances at room temperature in YSZ doping La0.67Sr0.33MnO3 system

The temperature dependence of the resistance of composite samples (1−x)La_0.67Sr_0.33MnO₃+xYSZ with different YSZ doping level x was investigated at magnetic fields 0-3 T, where YSZ represents yttria-stabilized zirconia. Results show that the YSZ dopant does not only adjust the metal-insulator transition temperature, but also increases the magnetoresistance effect. With increase of YSZ doping level for the range of x<2%, the metal-insulator transition temperature values T_P of the composites decrease, but T_P increases with increase of x further for the range of x>2%. Meanwhile, in the YSZ-doped composites, a broad metal-insulator transition temperature region was found at zero and low magnetic field, which results in an obvious enhanced magnetoresistance in the temperature range 10-350 K. Specially, a larger magnetoresistance value was observed at room temperature at 3 T, which is encouraging with regard to the potential application of magnetoresistance materials.     

Preparation and study of silver added La0.67Ca0.33MnO3 film

La_0.67Ca_0.33MnO₃ (LCMO) and Ag admixed La_0.67Ca_0.33MnO₃ (Ag-LCMO) polycrystalline films have been prepared on SrTiO₃ single crystal (100) substrates by ultrasonic spray pyrolysis technique. These films are characterized using XRD, SEM, and temperature dependence of resistivity (ρ-T) and ac susceptibility (χ-T). The films are having cubic structure with lattice parameters as 3.890 and 3.885 Å for LCMO and Ag-LCMO films, respectively. The peek in ρ-T curve (T_p) and the ferromagnetic transition temperature (T_C) for the Ag-LCMO film is higher than that of LCMO film. The stability of both the films was tested by repeated measurements of its characteristics over a period of one week after several thermal cycling from room temperature to 77 K. In the LCMO film, the peak in the ρ-T curve (T_p) is found to shift towards lower value and conduction noise of the film increases in the subsequent measurements. In the case of Ag-LCMO the value of T_p, T_C and conduction noise of the film did not change even after several measurements. Silver segregating at the grain boundaries in Ag-LCMO polycrystalline film seems to be responsible for improving the characteristics of Ag-LCMO films.     

Hydrogen annealing effects on polycrystalline La0.67Ba0.33MnO3 compound

Upon annealing polycrystalline La_0.67Ba_0.33MnO₃ bulk samples in flowing 95%Ar:5%H₂ mixed gas at 700 °C for different time, the insulator–metal transition temperature, _TP$T_{\mathrm{P}}$ and the amplitude of AC magnetic susceptibility were decreased first, then increased, finally decreased again. While the resistivity was increased monotonically. This anomalous behavior was explained by the combinational effects of oxygen loss and Ba ion vacancies caused by the segregation of Ba ion related impurity phase.     

Electric current-induced giant electroresistance in epitaxial La0.67Sr0.33MnO3 thin films

The electronic transport behavior of La_0.67Sr_0.33MnO₃ epitaxial thin films with different thicknesses has been investigated under various applied DC currents. The 20 and 70 nm thick films show a giant negative electroresistance (ER). In contrast, the films with 100 nm thickness show unusual giant positive ER, which can reach 30% with the current density of 1.8×10⁸ A/cm² at room temperature. It is interesting that the electric current can also change the magnetoresistance of the films. The results were explained by considering the spin polarized current induced increase of ferromagnetic metallic phase and current-induced lattice distortion via electron wind force under high current density.     

Revival of metastable behavior in phase separated La0.5Ca0.5MnO3+δ

The La_xCa_1−xMnO_3+δ compositions close to charge ordering (x∼0.5) show a gradual relaxation from a metallic/ferromagnetic state to an insulating/antiferromagnetic state with thermal cycling. Here, we report on the magnetic relaxation in the metastable state and also the revival of the metastable state (in a relaxed sample) due to high temperature thermal treatment. We also show the changes in the magnetization and the thermoelectric power as the revived metastable state is cycled. We find that the changes in the thermoelectric power extend well into the region above the charge ordering temperatures. This suggests that the micro-structural changes accompanying the thermal cycling leave their imprint in the paramagnetic insulating state as well.     

Response of the capacitance of a planar La0.67Ca0.33MnO3/SrTiO3/La0.67Ca0.33MnO3 heterostructure to an electric field

Manganite film electrodes were integrated with a spacer layer of strontium titanate to produce an epitaxial La_0.67Ca_0.33MnO₃/(1000 nm)SrTiO₃/La_0.67Ca_0.33MnO₃ (LCMO/STO/LCMO) heterostructure by laser ablation. At T = 300 K, the mechanical stresses in the STO layer relaxed to a considerable extent, while the LCMO electrodes were found to be under biaxial lateral tensile strain, with the lattice unit cell of the top electrode distorted considerably stronger (a _∥/a _⊥ ≈ 1.026) than that of the bottom electrode (≈1.008) (a _∥ and a _⊥ are the unit cell parameters in the substrate plane and along the normal to its surface, respectively). The reciprocal of the capacitance C of the plane-parallel LCMO/STO/LCMO film capacitors thus formed increased almost linearly with increasing temperature T in the range 50–250 K. At T < 100 K, the capacitance C decreased by approximately 50% in an electric field E = 40 kV/cm. After the electric field E was varied as 0 → + 100 kV/cm → 0, the capacitance C decreased by approximately 3% and the maximum in the C(E, T > 200 K) dependence shifted by approximately 9 kV/cm with respect to the point E = 0.     

Epitaxial growth La0.67Ca0.33MnO3 thin film by radio frequency sputtering method

Perfect epitaxial growth of La_0.67Ca_0.33MnO₃ (LCMO) thin film has been achieved on (1 0 0) LaAlO₃ (LAO) single crystal substrate by radio frequency sputtering method. X-ray diffraction (XRD) and electron diffraction analysis indicates that La_0.67Ca_0.33MnO₃ film grows epitaxially on LaAlO₃ along [1 0 0] direction of the substrate. The resistivity variation with temperature of the film shows a sharp metal to semiconductor transition peak around 253 K, which is close to that of the target. The magnetoresistance (MR) also reveals high quality epitaxy film characteristic at low temperatures and near the metal to semiconductor transition temperature.     

Pico-second photoelectric characteristic in manganite oxide La0.67Ca0.33MnO3 films

Ultrafast photoelectric characteristic has been observed in La_0.67Ca_0.33MnO₃ films on tilted SrTiO₃ substrates. A pico-second (ps) open-circuit photovoltage of the perovskite manganese oxide films has been obtained when the films were irradiated by a 1.064μm laser pulse of 25 ps duration. The rise time and full width at half-maximum of the photovoltage pulse are ～300 ps and ～700 ps, respectively. The photovoltaic sensitivity was as large as ～500 mV/mJ.     

Direct measurement of the magnetocaloric effect in La0.67Ca0.33MnO3

Polycrystalline perovskite La_0.67Ca_0.33MnO₃ was synthesized by a sol–gel method. Its adiabatic temperature change ΔT_ad induced by a magnetic field change was measured directly. At 268 K, near its Curie temperature T_C, ΔT_ad of La_0.67Ca_0.33MnO₃ induced by a magnetic field change of 2.02 T reaches 2.4 K. The latent heat Q and magnetic entropy change −ΔS_M induced by a magnetic field change were calculated from the temperature dependence of ΔT_ad and zero-field heat capacity C_p. The maximum values of Q and −ΔS_M in La_0.67Ca_0.33MnO₃ induced by a magnetic field change of 2.02 T are 1.85 J g⁻¹ and 6.9 J kg⁻¹ K⁻¹, respectively. The former is larger than the phase transition latent heat of heating or cooling, which is about 1.70 J g⁻¹.     

Magnetic field dependence of conductance and conduction noise of an artificial grain boundary junction in a La0.67Ba0.33MnO3 epitaxial thin film

A single artificial grain boundary in La_0.67Ba_0.33MnO₃ (LBMO) thin film has been prepared by depositing the film on a bicrystal substrate using laser ablation technique. We investigated the magnetic field dependence of magnetoresistance and conductance-voltage characteristics of the grain boundary at 77 K. A decrease of nonlinearity of current-voltage characteristics was observed upon application of magnetic field. The results are explained by assuming the presence of two different types of parallel conducting channels (metallic and highly resistive) across the grain boundary. The analysis of the results reveals that the application of magnetic field suppresses magnetic disorders at the grain boundary region and increases metallic conduction channels across the grain boundary. The temperature dependence of the conduction noise of the bicrystal grain boundary was measured at 0 and 1.5 kG magnetic field and compared with a microbridge on the LBMO film having no grain boundary. The presence of the grain boundary was found to enhance noise by one order of magnitude. The noise of a bicrystal grain boundary showed a decrease in the presence of 1.5 kG magnetic field for T<210 K. This decrease of noise confirms that the application of a magnetic field induces more metallic channels across the grain boundary.     

Anomalous paramagnetic behavior in the paramagnetic phase of La2/3−xYxCa1/3MnO3 studied through EPR and its relation to colossal magnetoresistance

Electron paramagnetic resonance on La_2/3−xY_xCa_1/3MnO₃ in the paramagnetic (PM) regime is presented for 0≤x≤0.133. The resonance linewidth (ΔH_pp) decreases with cooling, reaches the minimum at T_min, and then anomalously increases with further cooling toward T_c. Our analysis on ΔH_pp(T) below T_min shows that the anomalous PM behavior below T_min is due to the appearance of a ferromagnetic (FM) phase within the PM matrix caused by the applied magnetic fields. The correlation between the anomalous PM and the colossal magnetoresistance is discussed. We argue that both are caused by the phase segregation in which the compound is phase-separated into a mixture of FM and PM regions.