Catalytic synthesis and photoluminescence of needle-shaped 3C-SiC nanowires

Needle-shaped 3C-SiC nanowires were grown from commercially available SiC powders in a thermal evaporation process with iron as catalyst. A strong broad photoluminescence peak located around 450 nm was observed at room temperature, which may be ascribed to quantum size effects of nanomaterials. Needle-shaped 3C-SiC nanowires may have great potential applications such as blue-green light-emitting diodes and display devices.     

Hydrothermal synthesis and photoluminescence of the monophosphate LaPO4:Eu(5%)

Hexagonal LaPO₄·nH₂O and monoclinic LaPO₄ doped with Eu³⁺ powder phosphors were prepared through hydrothermal reaction, respectively, at 100 °C and 200 °C under fine control of the acidity in the starting materials based on lanthanide oxides and phosphoric acid. X-ray diffraction, infrared spectroscopy, thermogravimetric analysis, thermal treatment, scanning electron microscopy and fluorescence spectroscopy have been used to characterize these materials. The structural, morphological, and luminescent changes of the products due to the heating temperature are studied. The effect of the thermal treatment on the colorimetric characteristic of the red emission of the Eu³⁺ was investigated. The Commission Internationale de L’Eclairage (CIE) chromatic coordinates, dominant wavelength, and colour purity were determined, discussed and compared to other products like Eu³⁺-doped zinc aluminate (ZnAl₂O₄) and yttrium oxide (Y₂O₃).     

Luminescence studies on nitride quaternary alloys double quantum wells

We present theoretical photoluminescence (PL) spectra of undoped and p-doped Al_xIn_1−x−yGa_yN/Al_XIn_1−X−YGa_YN double quantum wells (DQWs). The calculations were performed within the k.p method by means of solving a full eight-band Kane Hamiltonian together with the Poisson equation in a plane wave representation, including exchange-correlation effects within the local density approximation. Strain effects due to the lattice mismatch are also taken into account. We show the calculated PL spectra, analyzing the blue and red-shifts in energy as one varies the spike and the well widths, as well as the acceptor doping concentration. We found a transition between a regime of isolated quantum wells and that of interacting DQWs. Since there are few studies of optical properties of quantum wells based on nitride quaternary alloys, the results reported here will provide guidelines for the interpretation of forthcoming experiments.     

Initial study on the structure and photoluminescence properties of SiC films doped with Al

SiC films doped with aluminum (Al) were prepared by the rf-magnetron sputtering technique on p-Si substrates with a composite target of a single crystalline SiC containing several Al pieces on the surface. The as-deposited films were annealed in the temperature range of 400-800 °C under nitrogen ambient. The thin films have been characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The results show that the introduction of Al into films hinders crystalline formation process. And with the increase of annealing temperature, more Si particles are formed in the films, which strongly affect the optical absorption properties. The photoluminescence (PL) spectra of the samples show two peaks at 370 nm and 412 nm. The intensities of the PL peaks are evidently improved after Al doped. We attribute the origin of the two PL peaks to a kind of Si-related defect centres. The obtained results are expected to have important applications in modern optoelectronic devices.     

Novel ultraviolet photoluminescence of ZnO/ZnGa2O4 composite layers

ZnO/ZnGa₂O₄ composite layers were synthesized by simple thermal oxidation of ZnS substrates with gallium in the air. The continuous-wave and time-resolved photoluminescence measurements for the composites were performed at room temperature. It is found that the visible deep level emission from ZnO in ZnO/ZnGa₂O₄ composite layer was almost suppressed. In addition, the UV emission with long lifetime was also observed in comparison with that of pure ZnO layer without ZnGa₂O₄.     

The structure and photoluminescence properties of Cr-doped SiC films

Cr-doped SiC films are prepared by the RF-magnetron sputtering technique on Si substrates with a composite target of a single-crystalline SiC containing several Cr pieces on the surface. The as-deposited films are annealed in the temperature of 1000 °C under nitrogen ambient. The structure of the samples has been characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and Raman scattering measurement. The results show that the SiC crystal is formed and that majority of Cr doped in the SiC resulted in the formation of the C clusters. Then the photoluminescence (PL) spectra of the samples are observed in the visible range at room temperature. The optical properties of the samples have also been discussed briefly. We attribute the origin of the 412-nm PL band to a kind of C cluster center.     

On photoluminescence properties of a-Si:H-based structures

Non-Gaussian photoluminescence peaks observed in a-Si:H-based structures at 6 K are interpreted as a consequence of the presence of different phases in material. Thin films of amorphous silicon deposited on glass substrate have been analyzed.The main aims of the contribution are (i) analysis of numerical data obtained by fitting procedure and (ii) formulation of corresponding conclusions in terms of structural properties of sample. Spectrum of a-Si:H-based samples can be interpreted as superposition of photoluminescence signals arising from two domains with different degrees of structural disordering. By our knowledge this result corresponds to real situation from view of structural properties of amorphous hydrogenated silicon. Under certain circumstances, decomposition of photoluminescence spectrum can give information of geometrical structure of sample.     

Room temperature synthesis and characterization of NaEuF4 nanorods and Na5Eu9F32 nanospheres

A simple solution-based route was used to selectively synthesize two ternary metal fluoride NaEuF₄ nanorods with hexagonal structure and Na₅Eu₉F₃₂ nanospheres with cubic structure at room temperature. It is found that NaEuF₄ nanorods can be transformed into Na₅Eu₉F₃₂ nanospheres with the increasing the reaction time in the presence of excessive NaF. The luminescence properties of these two metal fluorides were investigated and the possible formation mechanism was discussed.     

Photoluminescence properties of nitrogen-doped ZnO films deposited on ZnO single crystal substrates by the plasma-assisted reactive evaporation method

Photoluminescence (PL) spectra of nitrogen-doped ZnO films (ZnO:N films) grown epitaxially on n-type ZnO single crystal substrates by using the plasma-assisted reactive evaporation method were measured at 5 K. In PL spectra, free exciton emission at about 3.375 eV was very strong and emissions at 3.334 and 3.31 eV were observed. These two emissions are discussed in this paper. The nitrogen concentration in ZnO:N films measured by secondary ion mass spectroscopy was 10^19-20 cm⁻³. Current-voltage characteristics of the junction consisting of an n-type ZnO single crystal substrate and ZnO:N film showed good rectification. Also, ultraviolet radiation and visible light were emitted from this junction under a forward bias at room temperature. It is therefore thought that ZnO:N films have good crystallinity and that doped nitrogen atoms play a role as acceptors in ZnO:N films to form a good pn junction. From these phenomena and the excitation intensity dependency of PL spectra, emissions at 3.334 and 3.31 eV were assigned to neutral acceptor-bound exciton (A⁰X) emission and a donor-acceptor pair (DAP) emission due to doped nitrogen, respectively.     

Atomic layer deposition coating of ZnO shell for GaN-ZnO core-sheath heteronanowires

We have synthesized GaN-core/ZnO-shell nanowires and investigated effects of the ZnO coating. The X-ray diffraction pattern showed that as-synthesized samples are composed of GaN and ZnO. Transmission electron microscopy indicated that the deposited ZnO shell layer is poly-crystalline. The photoluminescence (PL) spectrum of GaN has been changed by the ZnO coating, where emission bands centered at roughly 1.9 eV, 2.5 eV, and 3.3 eV were newly added to the emissions from core GaN nanowires. We found that overall PL intensity has been significantly increased by coating the ZnO shell layers.     

Fabrication and characterization of Au/SiO2 nanocomposite films

Au/SiO₂ nanocomposite films were prepared by radio frequency sputtering technique and annealing. The above nanocomposite films were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and atomic force microscopy (AFM). The surface of the nanocomposite films was uniform with the particle diameter of 100-300 nm. The size of Au crystallites increased on increasing annealing time. The luminescent behavior of the nanocomposite films was characterized by photoluminescence (PL) with different excitation wavelengths. Two emission peaks at around 525 nm and 560 nm were observed with the excitation wavelength at 325 nm. An intensive emission peak at around 325 nm was observed with the excitation wavelength at 250 nm, which is related to the defective structure of the amorphous SiO₂ layer because of oxygen deficiency, and could be applied to many fields, such as ultraviolet laser and ultraviolet detector.     

Structural and optical properties of a-Si1−xCx:H films synthesized by dc magnetron sputtering technique

Hydrogenated amorphous SiC films (a-Si_1−xC_x:H) were prepared by dc magnetron sputtering technique on p-type Si(1 0 0) and corning 9075 substrates at low temperature, by using 32 sprigs of silicon carbide (6H-SiC). The deposited a-Si_1−xC_x:H film was realized under a mixture of argon and hydrogen gases. The a-Si_1−xC_x:H films have been investigated by scanning electronic microscopy equipped with an EDS system (SEM-EDS), X-ray diffraction (XRD), secondary ions mass spectrometry (SIMS), Fourier transform infrared spectroscopy (FTIR), UV-vis-IR spectrophotometry, and photoluminescence (PL). XRD results showed that the deposited film was amorphous with a structure as a-Si_0.80C_0.20:H corresponding to 20 at.% carbon. The photoluminescence response of the samples was observed in the visible range at room temperature with two peaks centred at 463 nm (2.68 eV) and 542 nm (2.29 eV). In addition, the dependence of photoluminescence behaviour on film thickness for a certain carbon composition in hydrogenated amorphous SiC films (a-Si_1−xC_x:H) has been investigated.     

Soft X-ray fluorescence and photoluminescence of Si nanocrystals embedded in SiO2

We have used ion-beam mixing to form Si nano-crystals in SiO₂ and SiO₂/Si multilayers, and applied photoluminescence and soft-X-ray emission spectroscopy to study the nanoparticles. Ion-beam mixing followed by heat treatment at 1100 °C for 2 h forms the Si nanocrystals. The ion-beam-mixed sample shows higher PL intensity than that of a Si-implanted SiO₂ film. Photon and electron-excited Si L_2,3 X-ray emission measurements were carried out to confirm the formation of Si nanocrystal in SiO₂ matrix after ion-beam mixing and heat treatment. It is found that Si L_2,3 X-ray emission spectra of ion-beam-mixed Si monolayers in heat-treated SiO₂ films lead to noticeable changes in the spectroscopic fine structure. Received: 20 November 1999 / Accepted: 17 April 2000 / Published online: 5 October 2000     

Investigation of porous silicon carbide as a new material for environmental and optoelectronic applications

In this paper, we present an experimental study on the chemical and electrochemical etching of silicon carbide (SiC) in different HF-based solutions and its application in different fields, such as optoelectronics (photodiode) and environment (gas sensors). The thin SiC films have been grown by pulsed laser deposition method. Different oxidant reagents have been explored. It has been shown that the morphology of the surface evolves with the etching conditions (oxidant, concentration, temperature, etc.). A new chemical polishing solution of polycrystalline 6H-SiC based on HF:Na₂O₂ solution has been developed. Moreover, an electrochemical etching method has been carried out to form a porous SiC layer on both polycrystalline and thin SiC films. The PL results show that the porous polycrystalline 6H-SiC and porous thin SiC films exhibited an intense blue luminescence and a green-blue luminescence centred at 2.82 eV (430 nm) and 2.20 eV (560 nm), respectively. Different device structures based on both prepared samples have been investigated as photodiode and gas sensors.     

Dominant ultraviolet-blue photoluminescence of ZnO embedded into synthetic opal

The temperature-dependent photoluminescence (PL) characteristics of zinc oxide (ZnO) embedded into the voids of synthetic opal were studied. ZnO was infiltrated into opal from aqueous solution with zinc nitrate precursor followed by thermal annealing. The PL spectra of the ZnO powder exhibit very high and broad emission peaks in the green region due to crystal defects, such as oxygen vacancies and zinc ion interstitials. In contrast to the PL spectra of ZnO powder, nanocrystals of ZnO embedded into the voids of FCC packed opal matrix exhibit dominant ultraviolet (UV)-blue and rapidly decreasing green PL emissions with decreasing temperature. The temperature-dependent PL characteristics show that the green band suppression in the ZnO nanocrystals is due to the influence of photonic crystal. The infiltration of nanoparticles into synthetic opal may be used for the fabrication of polycrystalline ZnO with dominant UV-blue PL. These results indicate that the luminescent materials embedded into photonic crystal may be promising for the fabrication of the RGB pixels in full-color displays.     

Electronic structure of solid C48N12 aza-fullerene

I report electronic structures and the cohesive energy for face-centered-cubic (fcc) solid C₄₈N₁₂ using generalized-gradient density-functional theory. The full vibrational spectrum of the C₄₈N₁₂ cluster is calculated within the harmonic approximation at the B3LYP/6-31G* level of theory. The results show that fcc is energetically preferred and a more stable crystal form than body-centered-cubic (bcc). C₄₈N₁₂ clusters are found to condense by a weak (0.29 eV) van der Waals force. The band gap of fcc C₄₈N₁₂ is calculated to be 1.3 eV at the GGA-PW91 level, whereas the HOMO-LUMO gap is calculated to be 2.74 eV using B3LYP/6-31G*.     

Microstructure related photoluminescence in a-CNx films deposited by reactive rf magnetron sputtering

We investigated the photoluminescence (PL) properties of carbon nitride films (CN_x) deposited by rf magnetron sputtering and compared them to their microstructure depending on the target self-bias. While many of the data are compatible with ‘a-C:H like’ PL properties the observed variation of the PL efficiency η with respect to the target bias cannot be easily explained by the standard models. It is suggested that the observed variation of η is rather dominated by a change in microstructure which depends on the bombardment intensity during growth than by the concentration of non-radiative centres.     

Excitonic polaron and phonon assisted photoluminescence of ZnO nanowires

The coupling strength of the radiative transition of hexagonal ZnO nanowires to the longitudinal optic (LO) phonon polarization field is deduced from temperature dependent photoluminescence spectra. An excitonic polaron formation is discussed to explain why the interaction of free excitons with LO phonons in ZnO nanowires is much stronger than that of bound excitons with LO phonons. The strong exciton-phonon coupling in ZnO nanowires affects not only the Haung-Ray S factor but also the FXA-1LO phonon energy spacing, which can be explained by the excitonic polaron formation.     

A combined approach to fabricating Si nanocrystals with high photoluminescence intensity

This work demonstrates that by combining three methods with different mechanisms to enhance the photoluminescence (PL) intensity of Si nanocrystals embedded in SiO₂ (or Si-nc:SiO₂), a promising material for developing Si light sources, a very high PL intensity can be achieved. A 30-layered sample of Si-nc:SiO₂/SiO₂ was prepared by alternatively evaporating SiO and SiO₂ onto a Si(1 0 0) substrate followed by thermal annealing at 1100 °C. This multilayered sample possessed a fairly high PL efficiency of 14% as measured by Greenham's method, which was 44 times that of a single-layered one for the same amount of excess Si content. Based on this multilayered sample, treatments of CeF₃ doping and hydrogen passivation were subsequently applied, and a high PL intensity which was 167 times that of a single-layered one for the same amount of excess Si content was achieved.