Ultrathin nickel oxide films grown on Ag(0 0 1): a study by XPS, LEIS and LEED intensity analysis

The structure of a nickel oxide film 2 ML thick has been investigated by LEED intensity analysis. The NiO film was prepared by evaporating Ni in presence of O₂ at a pressure in the 10⁻⁶ mbar range. The growth of the oxide film was followed by XPS, LEIS and LEED. In the early stages of deposition, the film shows a (2 × 1) superstructure in LEED. After deposition of 2 ML of NiO, a sharp (1 × 1) LEED pattern is observed. The intensity versus electron energy curves of the LEED spots were measured for this NiO(1 × 1) film and analysed by means of the tensor LEED method. A good level of agreement of the experimental LEED intensities with those calculated for a pseudomorphic NiO(0 0 1) film was obtained. We found that oxygen atoms at the oxide-substrate interface are on-top silver atoms. The interlayer distance in the oxide does not differ significantly from that in bulk NiO(0 0 1), within the accuracy of the analysis. An outward displacement (0.05 ± 0.05 Å) of oxygen atoms with respect to nickel atoms was found at the oxide film surface. The interlayer distance at the silver-nickel oxide interface is 2.43 ± 0.05 Å.     

The Fe/ZnO(0 0 0 1) interface: Formation and thermal stability

The room temperature growth mode and the interface reaction of Fe films on single crystalline ZnO(0 0 0 1) substrates prepared in ultra high vacuum (UHV) has been investigated by means of X-ray photoelectron and Auger electron spectroscopy (XPS, AES), low energy electron diffraction (LEED) and low energy ion scattering spectroscopy (LEIS). The results show that Fe grows in the pseudo layer-by-layer mode. At ambient temperature the deposited Fe film reduces the underlying ZnO single crystal resulting in FeO at the interface and metallic Zn, which partially diffuses into the remaining Fe overlayer. Annealing leads to a stepwise oxidation of the Fe to FeO (670 K) and Fe₂O₃ (820 K). The Fe₂O₃ mixes with the substrate resulting in two (1 1 1) oriented textures of a spinel phase found by electron backscatter diffraction analysis (EBSD). Fe-based spin-injection may play a vital role for ZnO-based spintronic devices.     

Initial stages of iron silicide formation on the Si(1 0 0)2 × 1 surface

The initial stages of iron silicide growth on the Si(1 0 0)2 × 1 surface during solid-phase synthesis were investigated by photoelectron spectroscopy using synchrotron radiation. The experiments were made on iron films of 1-50 monolayer (ML) thickness in the temperature range from room temperature to 750 °С. Our results support the existence of three stages in the Fe deposition on Si(1 0 0) at room temperature, which include formation of the Fe-Si solid solution, Fe₃Si silicide and an iron film. The critical Fe dose necessary for the solid solution to be transformed to the silicide is found to be 5 ML. The solid-phase reaction was found to depend on the deposited metal dose. At 5 ML, the reaction begins at 60 °С, and the solid-phase synthesis leads to the formation of only metastable silicides (FeSi with the CsCl-type structure, γ-FeSi₂ and α-FeSi₂). A specific feature of this process is Si segregation on the silicide films. At a thickness of 15 ML and more, we observed only stable phases, namely, Fe₃Si, ε-FeSi and β-FeSi₂.     

The surface structure of Fe3O4(1 1 1) films as studied by CO adsorption

We have studied adsorption of CO on Fe₃O₄(1 1 1) films grown on a Pt(1 1 1) substrate by temperature programmed desorption (TPD), infrared reflection absorption spectroscopy (IRAS) and high resolution electron energy loss spectroscopy (HREELS). Three adsorption states are observed, from which CO desorbs at ∼110, 180, and 230 K. CO adsorbed in these states exhibits stretching frequencies at ∼2115-2140, 2080 and 2207 cm⁻¹, respectively. The adsorption results are discussed in terms of different structural models previously reported. We suggest that the Fe₃O₄(1 1 1) surface is terminated by 1/2 ML of iron, with an outermost 1/4 ML consisting of octahedral Fe²⁺ cations situated above an 1/4 ML of tetrahedral Fe³⁺ ions, in agreement with previous theoretical calculations. The most strongly bound CO is assigned to adsorption to Fe³⁺ cations present on the step edges.     

Ab-initio investigation of Ni(Fe)/ZrO2(0 0 1) and Ni-Fe/ZrO2(0 0 1) interfaces

The atomic and electronic structures of Me/ZrO₂(0 0 1) interfaces, where Me is Ni, Fe or a Ni-Fe alloy, are investigated by the plane wave pseudopotential method within density-functional theory. The work of separation of metal films from oxide substrate for the O- and Zr-terminated Me/ZrO₂(0 0 1) interfaces is calculated. High adhesion at both Me/(ZrO₂)_O and Me/(ZrO₂)_Zr interfaces is found. The effect of oxygen vacancies on the adhesion at the metal-ceramic interfaces is also investigated. It is shown that Ni(Fe)-O interaction at the O-terminated interface weakens in the presence of interfacial oxygen vacancies. At interfaces with Ni-Fe alloys the adhesion depends strongly on the composition of the interfacial layers and their magnetic properties.     

FeO(1 1 1) formation by exposure of Fe(1 1 0) to atomic and molecular oxygen

The growth, structure, and morphology of ultrathin iron oxide layers formed on a Fe(1 1 0) single crystal surface are investigated by Auger electron spectroscopy, low energy electron diffraction, and grazing ion scattering. For Fe oxidation by atomic instead of molecular oxygen, the gas exposure can be reduced by almost two orders of magnitude because surface sticking and dissociation are not limiting the growth process. A well-ordered FeO(1 1 1) film with low defect density is only obtained with atomic oxygen. Compared to the bulk, the FeO lattice is laterally compressed by about 5-6% resulting in an in-plane oxygen (Fe) nearest-neighbor distance of 2.87 Å. Independent of the preparation method, long-range structural order is poor if the oxide film thickness is increased to 3-5 layers. This is attributed to the relatively large lattice mismatch between FeO(1 1 1) and Fe(1 1 0).     

Growth and oxidation of a Ni3Al alloy on Ni(1 0 0)

The growth and oxidation of a thin film of Ni₃Al grown on Ni(1 0 0) were studied using Auger electron spectroscopy (AES), low energy electron diffraction (LEED), and high resolution electron energy loss spectroscopy (EELS). At 300 K, a 12 Å thick layer of aluminium was deposited on a Ni(1 0 0) surface and subsequently annealed to 1150 K resulting in a thin film of Ni₃Al which grows with the (1 0 0) plane parallel to the (1 0 0) surface of the substrate. Oxidation at 300 K of Ni₃Al/Ni(1 0 0) until saturation leads to the growth of an aluminium oxide layer consisting of different alumina phases. By annealing up to 1000 K, a well ordered film of the Al₂O₃ film is formed which exhibits in the EEL spectra Fuchs-Kliewer phonons at 420, 640 and 880 cm⁻¹. The LEED pattern of the oxide shows a twelvefold ring structure. This LEED pattern is explained by two domains with hexagonal structure which are rotated by 90° with respect to each other. The lattice constant of the hexagonal structure amounts to ∼2.87 Å. The EELS data and the LEED pattern suggest that the γ^′-Al₂O₃ phase is formed which grows with the (1 1 1) plane parallel to the Ni(1 0 0) surface.     

Formation and hydrogenation of p(2 × 2)-N on Pt(1 1 1)

The formation of a well-ordered p(2 × 2) overlayer of atomic nitrogen on the Pt(1 1 1) surface and its reaction with hydrogen were characterized with reflection absorption infrared spectroscopy (RAIRS), temperature programmed desorption (TPD), low energy electron diffraction (LEED), Auger electron spectroscopy (AES), and X-ray photoelectron spectroscopy (XPS). The p(2 × 2)-N overlayer is formed by exposure of ammonia to a surface at 85 K that is covered with 0.44 monolayer (ML) of molecular oxygen and then heating to 400 K. The reaction between ammonia and oxygen produces water, which desorbs below 400 K. The only desorption product observed above 400 K is molecular nitrogen, which has a peak desorption temperature of 453 K. The absence of oxygen after the 400 K anneal is confirmed with AES. Although atomic nitrogen can also be produced on the surface through the reaction of ammonia with an atomic, rather than molecular, oxygen overlayer at a saturation coverage of 0.25 ML, the yield of surface nitrogen is significantly less, as indicated by the N₂ TPD peak area. Atomic nitrogen readily reacts with hydrogen to produce the NH species, which is characterized with RAIRS by an intense and narrow (FWHM ∼ 4 cm⁻¹) peak at 3322 cm⁻¹. The areas of the H₂ TPD peak associated with NH dissociation and the XPS N 1s peak associated with the NH species indicate that not all of the surface N atoms can be converted to NH by the methods used here.     

Alloy formation of Co/Ni/Pt(1 1 1)

The initial growth and alloy formation of ultrathin Co films deposited on 1 ML Ni/Pt(1 1 1) were investigated by Auger electron spectroscopy (AES), low energy electron diffraction (LEED), and ultraviolet photoelectron spectroscopy (UPS). A sequence of samples of d_Co Co/1 ML Ni/Pt(1 1 1) (d_Co = 1, 2, and 3 ML) were prepared at room temperature, and then heated up to investigate the diffusion process. The Co and Ni atoms intermix at lower annealing temperature, and Co-Ni intermixing layer diffuses into the Pt substrate to form Ni-Co-Pt alloys at higher annealing temperature. The diffusion temperatures are Co coverage dependent. The evolution of UPS with annealing temperatures also shows the formation of surface alloys. Some interesting LEED patterns of 1 ML Co/1 ML Ni/Pt(1 1 1) show the formation of ordered alloys at different annealing temperature ranges. Further studies in the Curie temperature and concentration analysis, show that the ordered alloys corresponding to different LEED patterns are Ni_xCo_1−xPt and Ni_xCo_1−xPt₃. The relationship between the interface structure and magnetic properties was investigated.     

Spin-engineering in the Co75Fe25/Cu(1 1 0) system

We present results on the growth and magnetic anisotropies of Co₇₅Fe₂₅ films grown on a Cu(1 1 0) single crystal. Angular dependent MOKE measurements show a thickness dependent, in-plane rotation of the easy axis of magnetisation of up to 60° from the [0 0 1] direction (towards [−1 1 0]). For a film thickness of 5 ML, just greater than that required for the onset of ferromagnetism, uniaxial anisotropy is observed with the easy axis along the [0 0 1] direction. As the film thickness increases this is seen to rotate in-plane towards the [−1 1 0] direction as the contribution from the cubic anisotropy constant grows. At a film thickness of 9 ML there is predominantly cubic anisotropy and at 10 ML the easy axis is rotated to 150° with respect to the [1 −1 0] axis, where it is stabilised.     

Growth of Ce on Rh(1 1 1)

We have studied the growth of cerium films on Rh(1 1 1) using STM (scanning tunneling microscopy), LEED (low energy electron diffraction), XPS (X-ray photoelectron spectroscopy) and AES (Auger electron spectroscopy). Measurements of the Ce films after room temperature deposition showed that Ce is initially forming nanoclusters in the low coverage regime. These clusters consist of 12 Ce atoms and have the shape of pinwheels. At a coverage of 0.25 ML (monolayer, ML) an adatom layer with a (2 × 2) superstructure is observed. Above 0.4 ML, Rh is diffusing through pinholes into the film, forming an unstructured mixed layer. Annealing at 250 °C leads to the formation of ordered Ce-Rh compounds based on the bulk compound CeRh₃. At a coverage of 0.1 ML, small ordered (2 × 2) surface alloy domains are observed. The exchanged Rh atoms form additional alloy islands situated on the pure Rh(1 1 1) surface, showing the same (2 × 2) superstructure as the surface alloy. At a coverage of 0.25 ML, the surface is completely covered by the surface alloy and alloy islands. The (2 × 2) structure is equivalent to a (1 1 1)-plane of CeRh₃, contracted by 6%. Annealing a 1 ML thick Ce layer leads to a flat surface consisting of different rotational domains of CeRh₃(1 0 0). The Rh needed for alloy formation comes from 50 Å deep pits in the substrate. Finally we show that LEIS (low energy ion scattering) is not suitable for the characterization of Ce and CeRh films due to strong effects of neutralization.     

Reduction of FeO/Pt(1 1 1) thin films by exposure to atomic hydrogen

Using scanning tunneling microscopy (STM), X-ray photoemission spectroscopy (XPS) and density functional theory (DFT) calculations we have studied the reduction of ultra-thin films of FeO(1 1 1) grown on Pt(1 1 1) after exposure to atomic hydrogen at room temperature. A number of new ordered, partly-reduced FeO_x structures are identified and as a general trend we reveal that all the reduced FeO_x structures incorporate 2-fold coordinated Fe atoms as opposed to the original 3-fold coordinated Fe atoms in the FeO film. We find that when all the Fe atoms are 2-fold O-coordinated the FeO_x surface structure is resistant to further reduction at room temperature. We observe that water easily dissociates on the most heavily reduced FeO_x, structure in contrast to the initially inert FeO film, and reveal that it is possible to partially re-oxidize the FeO_x film by heating the surface slightly in the presence of water.     

A route to continuous ultra-thin cerium oxide films on Cu(1 1 1)

The growth and morphology of ultra-thin CeO₂(1 1 1) films on a Cu(1 1 1) substrate were investigated by means of low energy electron diffraction (LEED) and scanning tunneling microscopy (STM). The films were grown by physical vapor deposition of cerium in an oxygen atmosphere at different sample temperatures. The preparation procedure is based on a modification of a previous method suggested by Matolin and co-workers [1], involving growth at elevated temperature (520 K). Here, LEED shows good long range ordering with a “(1.5 × 1.5)” superstructure, but STM reveals a three-dimensional growth mode (Vollmer-Weber) with formation of a closed film only at larger thickness. Using a kinetically limited growth process by reactive deposition at low sample temperatures (100 K) and subsequent annealing, we show that closed layers of ceria with atomically flat terraces can be prepared even in the regime of ultra-thin films (1.5 ML). Closed and atomically flat ceria films of larger thickness (3 ML) are obtained by applying a multistep preparation procedure, in which successive ceria layers are homoepitaxially grown on this initial film. The resulting overlayers show strong similarities with the morphology of CeO₂(1 1 1) single crystal surfaces, suggesting the possibility to model bulk ceria by thin film systems.     

Herringbone and triangular patterns of dislocations in Ag, Au, and AgAu alloy films on Ru(0 0 0 1)

We have studied the dislocation structures that occur in films of Ag, Au, and Ag_0.5Au_0.5 alloy on a Ru(0 0 0 1) substrate. Monolayer (ML) films form herringbone phases while films two or more layers thick contain triangular patterns of dislocations. We use scanning tunneling microscopy (STM) and low-energy electron diffraction (LEED) to determine how the film composition affects the structure and periodicity of these ordered structures. One layer of Ag forms two different herringbone phases depending on the exact Ag coverage and temperature. Low-energy electron microscopy (LEEM) establishes that a reversible, first-order phase transition occurs between these two phases at a certain temperature. We critically compare our 1 ML Ag structures to conflicting results from an X-ray scattering study [H. Zajonz et al., Phys. Rev. B 67 (2003) 155417]. Unlike Ag, the herringbone phases of Au and AgAu alloy are independent of the exact film coverage. For two layer films in all three systems, none of the dislocations in the triangular networks thread into the second film layer. In all three systems, the in-plane atomic spacing of the second film layer is nearly the same as in the bulk. Film composition does, however, affect the details of the two layer structures. Ag and Au films form interconnected networks of dislocations, which we refer to as “trigons.” In 2 ML AgAu alloy, the dislocations form a different triangular network that shares features of both trigon and moiré structures. Yet another well-ordered structure, with square symmetry, forms at the boundaries of translational trigon domains in 2 ML Ag films but not in Au films.     

Growth of ultra-thin cerium oxide layers on Cu(1 1 1)

The reactive vacuum deposition of CeO₂ on Cu(1 1 1) surface in oxygen atmosphere provides high quality epitaxial ceria overlayers. We report the growth characteristics of Ce oxide, the structures, and the temperature stability of the oxide phases as investigated by low-energy electron diffraction (LEED) and X-ray photoelectron spectroscopy. We find that Ce oxide on the Cu(1 1 1) grows initially in the form of islands giving sharp hexagonal LEED pattern of the CeO₂(1 1 1) structure corresponding to the (1.5 × 1.5) structure. The CeO₂-Cu(1 1 1) films exhibited mixed valence states and temperature dependent CeO₂-Ce₂O₃ transition above 900 K due to the vacuum annealing. The transition progressed more rapidly at the surface, probably by formation of oxygen vacancies.     

Oxidation of Pt(1 0 0)-hex-R0.7° by gas-phase oxygen atoms

We utilized temperature programmed desorption (TPD), X-ray photoelectron spectroscopy (XPS), electron energy loss spectroscopy (ELS), and low energy electron diffraction (LEED) to investigate the oxidation of Pt(1 0 0)-hex-R0.7° at 450 K. Using an oxygen atom beam, we generated atomic oxygen coverages as high as 3.6 ML (monolayers) on Pt(1 0 0) in ultrahigh vacuum (UHV), almost 6 times the maximum coverage obtainable by dissociatively adsorbing O₂. The results show that oxidation occurs through the development of several chemisorbed phases prior to oxide growth above about 1 ML. A weakly bound oxygen state that populates as the coverage increases from approximately 0.50 ML to 1 ML appears to serve as a necessary precursor to Pt oxide growth. We find that increasing the coverage above about 1 ML causes Pt oxide particle growth and significant surface disordering. Decomposition of the Pt oxide particles produces explosive O₂ desorption characterized by a shift of the primary TPD feature to higher temperatures and a dramatic increase in the maximum desorption rate with increasing coverage. Based on thermodynamic considerations, we show that the thermal stability of the surface Pt oxide on Pt single crystal surfaces significantly exceeds that of bulk PtO₂. Furthermore, we attribute the high stability and the acceleratory decomposition rates of the surface oxide to large kinetic barriers that must be overcome during oxide formation and decomposition. Lastly, we present evidence that structurally similar oxides develop on both Pt(1 1 1) and Pt(1 0 0), therefore concluding that the properties of the surface Pt oxide are largely insensitive to the initial structure of the Pt single crystal surface.     

Growth of epitaxial thin Pd(1 1 1) films on Pt(1 1 1) and oxygen-terminated FeO(1 1 1) surfaces

Thin Pd films (1-10 monolayers, ML) were deposited at 35 K on a Pt(1 1 1) single crystal and on an oxygen-terminated FeO(1 1 1) monolayer supported on Pt(1 1 1). Low energy electron diffraction, Auger electron spectroscopy, and Kr and CO temperature programmed desorption techniques were used to investigate the annealing induced changes in the film surface morphology. For growth on Pt(1 1 1), the films order upon annealing to 500 K and form epitaxial Pd(1 1 1). Further annealing above 900 K results in Pd diffusion into the Pt(1 1 1) bulk and Pt-Pd alloy formation. Chemisorption of CO shows that even the first ordered monolayer of Pd on Pt(1 1 1) has adsorption properties identical to bulk Pd(1 1 1). Similar experiments conducted on FeO(1 1 1) indicate that 500 K annealing of a 10 ML thick Pd deposit also yields ordered Pd(1 1 1). In contrast, annealing of 1 and 3 ML thick Pd films did not result in formation of continuous Pd(1 1 1). We speculate that for these thinner films Pd diffuses underneath the FeO(1 1 1).     

Growth and alloy formation of ultrathin Ni films on Co/Pt(1 1 1)

Low-energy electron diffraction (LEED) and Auger electron spectroscopy (AES) were used to study the growth and the structural evolution of Ni/Co/Pt(1 1 1) following high-temperature annealing. From the oscillation of the specular beam of the LEED and Auger uptake curve, we concluded that the growth mode of thin Ni films on 1 ML Co/Pt(1 1 1) is at least 2 ML layer-by-layer growth before three-dimensional island growth begins. The alloy formation of Ni/1 ML Co/Pt(1 1 1) was analyzed by AES. The temperature for the intermixing of Ni and Co layers in the upper interface without diffusing into the bulk of Pt is independent of the thickness of Ni when a Co buffer is one atomic monolayer. After the temperature was increased, formations of Ni-Co-Pt alloy, Ni-Pt alloy and Co-Pt alloy were observed. The temperature required for the Ni-Co intermixing layer to diffuse into Pt bulk increases with the thickness of Ni. The interlayer distance as a function of annealing temperature for 1 ML Ni/1 ML Co/Pt(1 1 1) was calculated from the I-V LEED. The evolution of LEED patterns was also observed at different annealing temperatures.     

Pt interactions with annealed and chemically-etched Nb-doped SrTiO3(0 0 1) surfaces: Metal/oxide surface chemical effects on band bending behavior

XPS and LEED have been used to characterize the interaction of sputter-deposited Pt (maximum coverage <5 ML) with Nb-doped SrTiO₃(0 0 1) surfaces prepared either by annealing in O₂ and then UHV, or by chemical-etching in aqua regia. The annealed surface exhibits an ordered (1 × 1) LEED pattern, with additional diffraction spots and streaks indicating the presence of oxygen vacancies. Increasing Pt coverage results in the decrease of the observed Pt(4f_7/2) binding energy and the uniform shift of the Sr(3d), Ti(2p) and O(1s) levels to smaller binding energies, as expected for Pt cluster growth and surface-to-Pt charge donation on an n-type semiconductor. The etched surface is disordered, and exhibits a hydroxylated surface with a contaminant C film of ∼23 ? average thickness. Pt deposition on the etched surface results in an immediate decrease in the intensity of the OH feature in the O(1s) spectrum, and a uniform shift of the Sr(3d), Ti(2p) and O(1s) levels to larger binding energies with increasing Pt coverage. The observed Pt(4f_7/2) binding energy on the etched surface (∼72 eV) is independent of Pt coverage, and indicates substantial electronic charge donation from the Pt to surface hydroxyl species. The observation of band bending towards higher binding energies upon Pt deposition (behavior normally associated with p-type semiconductors) demonstrates that sub-monolayer quantities of adsorbates can alter metal/oxide interfacial charge transfer and reverse the direction of band bending, with important consequences for Schottky barrier heights and device applications.     

Methanol adsorption on a CeO2(1 1 1)/Cu(1 1 1) thin film model catalyst

Adsorption and desorption of methanol on a CeO₂(1 1 1)/Cu(1 1 1) thin film surface was investigated by XPS and soft X-ray synchrotron radiation PES. Resonance PES was used to determine the occupancy of the Ce 4f states with high sensitivity. Methanol adsorbed at 110 K formed adsorbate multilayers, which were partially desorbed at 140 K. Low temperature desorption was accompanied by formation of chemisorbed methoxy groups. Methanol strongly reduced cerium oxide by forming hydroxyl groups at first, which with increasing temperature was followed by creation of oxygen vacancies in the topmost cerium oxide layer due to water desorption. Dissociative methanol adsorption and creation of oxygen vacancies was observed as a Ce⁴⁺ → Ce³⁺ transition and an increase of the Ce 4f electronic state occupancy.