Continuous dynamic-gravimetric preparation of calibration gas mixtures for air pollution measurements

 The preparation of calibration gas mixtures for air pollution measurements by the dynamic-gravimetric method was investigated using sulphur dioxide in nitrogen as a model. The target mole fraction was 200×10^–9 mol/mol, with the option of also getting smaller mole fractions. Thermal mass flow meters calibrated with reference mass flows were used to measure the dilution gas flow (nitrogen). The relative standard uncertainty of the dilution gas flows between 10 mg/s (approx. 500 ml/min) and 40 mg/s (approx. 2000 ml/min) was 0.15%. The mass flow of the target component measured as the permeation rate was determined via the quasi-continuous observation of the loss in the permeation tube mass during the measuring time. A magnetic coupling system and an adapted microbalance were used for this purpose. The results presented show permeation rates measured over the lifetime of a tubular permeation source. The measurement cycles took between 3 days and 7 h at least. The relative standard uncertainty of the mixture composition did not exceed 2%. First comparisons with gas mixtures prepared by the static-gravimetric method show compatibility. The applicability of the system is not restricted to the SO₂/N₂ mixture. It can also be used for preparing other gas mixtures in this field of application. Received: 26 April 2000 / Accepted: 12 September 2000     

Sensitive and selective determination of mercury by differential pulse stripping voltammetry after accumulation of mercury vapour on a gold plated graphite electrode

 A selective and sensitive method is proposed for the determination of mercury by anodic stripping voltammetry after its preconcentration from the gas phase. Mercury from the sample solution is reduced to elemental Hg by SnCl₂ and volatilized by the bubbles of a carrier gas. The gas containing mercury vapour is dried and passed through a capillary onto a gold coated graphite electrode. An anodic stripping voltammogram is recorded from 0.1 mol/l HClO₄+3×10^-3 mol/l HCl solution. The calibration curve is linear from 1×10^-9 to 4×10^-8 mol/l Hg(NO₃)₂. The absolute detection limit is 0.46 ng Hg. The relative standard deviations for 4×10^-9 mol/l and 2×10^-8 mol/l Hg(NO₃)₂ are 9.8% and 6.1%, respectively (n=5). Received: 18 December 1995/Revised: 16 April 1996/Accepted: 20 April 1996     

Spectrophotometric flow injection determination of trace iodide in table salt and laver through the reaction of iodate with 3,5-Br2-PADAP and thiocyanate

A new simple, rapid and sensitive spectrophotometric flow injection method for the determination of trace iodide is described based on an ion associate of iodate (IO₃ ^–) with 2- (3,5-dibromo-2-pyridylazo)-5-diethylamino-phenol (3,5-Br₂-PADAP) and thiocyanate (SCN^–). In a strongly acidic medium, this unstable violet product was formed with an absorption maximum at 605 nm. Flow injection is an ideal method to reproducibly monitor the transient signal. Various parameters were optimized using the Super Modified Controlled Weighted Centroid Simplex Method (SMCWC). Under the optimum experimental conditions, iodide could be determined in the range of 1.00 × 10^–6 and 2.4 × 10^–5 mol l^–1. The correlation coefficient of the calibration curve is 0.9991. With a sampling frequency of 80 h^–1, the detection limit for iodide is 5.0 × 10^–7 mol l^–1. The proposed method has been applied to the determination of trace iodide after oxidizing I^– in table salt or laver to IO₃ ^–. In addition, the mechanisms of the ion association reaction was studied. Received: 15 August 1996 / Revised: 10 October 1996 / Accepted: 16 October 1996     

A study of HPLC separation and spectrophotometric and voltammetric detection of 4′-substituted derivatives of 3-carboxy-4-hydroxy-6-acetylaminoazobenzene

 Optimised conditions have been found for the separation of 3-carboxy-4-hydroxy-6-acetylaminoazo-benzene derivatives substituted in the position 4′ (4′-R-CHAAB, where R=–H, –CH₃, –OCH₃, –Cl, –COCH₃, –NO₂ and –NHCOCH₃) using reversed phase HPLC with a C18 chemically bonded stationary phase. Suitable mobile phases are mixtures of 0.01 mol/L NaH₂PO₄ at pH 4 with methanol (1+1), 0.01 mol/L NaH₂PO₄ at pH 2 with acetonitrile (1+1) or 1% aqueous acetic acid with methanol (4+6). UV photometry is the most universal detection technique and yields limits of detection around 10^-6 mol/L. Direct anodic voltammetry on a glassy carbon fibre array detector yields lower limits of detection for –COCH₃ derivatives and higher limits of detection for –NO₂ and –NHCOCH₃ derivatives. When the analytes are chemically reduced using zinc powder in acetic acid, the voltammetric detection has limits of detection one order of magnitude lower than those obtained UV photometrically. Received: 27 June 1996/Revised: 25 October 1996/Accepted: 3 November 1996     

Continuous Monitoring of Sulfur Dioxide with a Gas Permeation Denuder-Based System

 This study describes a continuous flow procedure for monitoring atmospheric sulfur dioxide using a planar gas permeation denuder (GPD) and a fiber optic spectrometer. When gaseous samples are directed through a GPD which consists of a gas-permeable membrane of poly(vinylidene) difluoride and two perspex blocks with engraved channels of mirror image, the fraction of sulfur dioxide passing the membrane is absorbed in a flowing stream of 5.0×10⁻⁴ mol L⁻¹ 5,5′-dithiobis(2,2′-dinitrobenzoic acid) (DTNB) in 0.025 mol L⁻¹ phosphate buffer of pH 7.0, and reacts with DTNB to yield a yellow product. This product is monitored spectrophotometrically at 410 nm with a miniature charge-coupled device (CCD) fiber optic spectrometer. The analytical range of sulfur dioxide is easily adjusted via the flow rate of DTNB solution, normally from 200 ppb to 94 ppm (v/v). The procedure is hardly interfered with by coexisting metal and non-metal species, except for hydrogen sulfide in the atmosphere. The error caused by hydrogen sulfide at a sulfur dioxide level (in ppm) of 2% is less than ±10%. With the proposed procedure, the result for a mimetic air sample is very close to that of the ultraviolet fluorescence method. Correspondence: College of Chemistry and Molecular Engineering, Peking University, Beijing 100871, China. e-mail: yli@chem.pku.edu.cn Received August 12, 2002; accepted November 9, 2002     

Solubility of sulphur dioxide in aqueous electrolyte solutions at higher ionic strengths—Chloride and bromide containing systems

The absorption of sulphur dioxide in chloride and bromide containing electrolyte solutions was measured up to ionic strengths of 5 mol/dm³. The thermodynamic equilibrium of the gas phase and the liquid phase was characterized by UV spectroscopy. UV spectra analysis gave strong evidence for SO₂X⁻ complexes existing in the solutions. Consequently, these compounds were implemented in the reaction scheme for absorption.     

Oxygen permeation and stability of Zr0.8Y0.2O0.9‒La0.8Sr0.2CrO3-δ dual-phase composite

A tubular membrane made of Zr_0.8Y_0.2O_1.9 (60 vol%) and was prepared by a standard ceramic process. Oxygen permeation through the membrane tube was examined by exposing its outer shell to air and sweeping its inner wall with pure helium or CO balanced with helium. An oxygen flux of 9.2×10⁻⁹ mol cm⁻² s⁻¹ was measured at 950°C under air/He gradient, and a larger flux of 3.2×10⁻⁸ mol cm⁻² s⁻¹ at 930°C under air/CO gradient. The membrane tube was found to exhibit excellent stability under highly reducing atmosphere and elevated temperatures. The oxygen permeation rate is likely to be increased through the modification of the surface and reduction of the membrane thickness.     

Poly(3,4-ethylenedioxythiophene)-modified nafion membrane for direct methanol fuel cells

Membranes Nafion 117 are modified with poly(3,4-ethylenedioxythiophene) (PEDT) by chemical polymerization of EDT with H₂O₂ or FeCl₃ as the oxidants in a two-compartment cell. Depending on the oxidant and polymerization conditions, PEDT is deposited either as a thin film on the membrane surface or inside the Nafion membrane depending on whether FeCl₃ or H₂O₂ is used as the oxidant. The decrease in the ionic conductivity and methanol permeability is studied as a function of the polymerization time. A linear dependence is found with H₂O₂ and a t ^−1/2 dependence, with FeCl₃. The contributions of PEDT and Nafion to the overall conductivity of the composite membranes are separated by impedance measurements. The modified membranes (FeCl₃) are also tested in direct methanol fuel cells (DMFC). The methanol permeation through the membranes is measured by operating the fuel cell in an electrolysis mode. The influence of the modified membranes on the DMFC current-voltage characteristics is studied with 2 M CH₃OH and O₂ at 1.2 bar_abs and 80°C. Membrane electrode assemblies (MEAs) are prepared by hot pressing the modified membrane between two commercial gas diffusion electrodes with 1 mg cm⁻² of Pt loading. A decrease of the methanol permeation of 25% is observed at MEA with the modified membrane (1 h polymerization time), compared with that of MEA with a Nafion membrane. However, the overall DMFC performance decreases in the same relation: a maximal power density of 36 W cm⁻² is measured at MEA with a PEDT-modified membrane compared with 45 W cm⁻² for MEA with a Nafion membrane. Published in Russian in Elektrokhimiya, 2006, Vol. 42, No. 11, pp. 1330–1339. Based on the report delivered at the 8th International Frumkin Symposium “Kinetics of the Electrode Processes,” October 18–22, 2005, Moscow. The text was submitted by the authors in English.     

A flow analysis system with an amperometric detector for the determination of hydrogen sulphide in waters

 A flow analysis system with an amperometric H₂S detector and a gas extraction unit as well as an integrated coulometric calibration unit is described, which allows an on-line determination of hydrogen sulphide in aquatic samples. By variation of different parameters (e.g. flow rate, gas injection volume, pH of solution) a wide dynamic working range of concentrations from 1 μmol/l H₂S to 750 μmol/l is accessible. The sampling rate is about 36 samples h⁻¹ using an average flow rate of 1.78 ml/min and a gas injection volume of 28 μl. The measuring system is designed as a portable device. In combination with the polyethylene-tube of a PTFE-underwater pump field-measurements on board are possible. Received: 16 February 1995/Revised: 5 April 1995/Accepted: 11 April 1995 Acknowledgements. This work was supported by the Bundesminister für Forschung und Technologie under the project “DYSMON II” (03F0123D) and by the Fonds der Chemischen Industrie zur F?rderung von Chemie und Biologischer Chemie. Correspondence to: P. Jeroschewski     

Spectrophotometric determination of trimethoprim by oxidation in drug formulations

A spectrophotometric determination of trimethoprim is described based on the reaction of its amine group with persulfate which acts as a strong oxidizing agent in alkaline media. The reaction produces a stable yellow colored compound after heating in a boiling water bath for 30 min. At λ_max 355 nm, Beer’s law is obeyed in the concentration range 10–60 μg ml^–1 with a molar absorptivity of 2.7 × 10³ l mol^–1cm^–1. The method is applied to formulations with sulfamethoxazole. Received: 30 July 1996 / Revised: 16 October 1996 / Accepted: 22 October 1996     

A simple laboratory generator for low concentrations of sulphur dioxide

The generator is based on permeation of sulphur dioxide through silicone rubber tubes immersed in a buffered, thermostated solution of sodium hydrogensulphite. The generator contains three (or more) permeation tubes of different lengths immersed simultaneously in the generation solution. The tubes can be connected stepwise to the carrier gas source, so that three (or more) different concentrations of SO₂ in the carrier gas can be obtained from a single solution. The tested generator produced 1.25–25.4 ng s^?1 SO₂, depending on the hydrogensulphite concentration in the solution. Long-term stability was tested for the production of 10.49 ng s^?1 over 50 h; the relative standard deviation was 1.57%. The experimental conditions affecting the production of SO₂ are discussed. An equation is derived for estimating the SO₂ production for various solution compositions and surface areas of the permeation tubes.     

Novel dissolution procedure using a mixture of manganese dioxide and hydrochloric acid for the matrix-independent determination of gold

 A mixture of manganese dioxide and hydrochloric acid has been used for the accurate and precise determination of gold in various gold-bearing matrices. Results of intermethod comparison studies, F-test on variances, Mann-Whitney U-test, Spearman rank correlation and regression analyses are presented. The recommended method can be applied to a quality control programme and for the evaluation of reference materials. Various standard reference materials (SRM) of diverse matrices have been examined to check the validity of the method and the results were found to be in very good agreement with the certified data. Sample decomposition is straight forward [1–10 g sample (roasted at 600–700 °C)+5 g of MnO₂+30 mL of 2 mol/L HCl]. Gold is coprecipitated with potassium tellurite using tin (II) chloride solution. The precipitate is extracted into toluene and finally stripped back into aqua-regia solution for final nebulization into an air-acetylene flame for atomic absorption spectrophotometry. The method is very simple and easily adaptable, and more convenient than conventional methods involving aqua regia or a hydrobromic acid-bromine water mixture. Received: 23 October 1995/Revised: 18 March 1996/Accepted: 23 March 1996     

Anodic stripping voltammetric determination of total lead, copper and selenium in whole blood and blood serum

A two-step procedure including appropriate wet-digestions, separation of selenium from interfering ions such as heavy metal ions with pentyl alcohol and anodic stripping voltammetric (ASV) determination of Pb²⁺, Cu²⁺ and SeO₃ ^2– is developed. The elements in digested whole blood and serum sample solutions were determined by using a standard addition method. 1 × 10^–9 mol/L SeO^2– ₃, Cu²⁺ and Pb²⁺ were successfully determined with relative standard deviations of approximately 1–2% (n = 6–8). Received: 19 August 1996 / Revised: 24 February 1997 / Accepted: 28 February 1997     

Sensitive and selective determination of mercury by differential pulse stripping voltammetry after accumulation of mercury vapour on a gold plated graphite electrode

A selective and sensitive method is proposed for the determination of mercury by anodic stripping voltammetry after its preconcentration from the gas phase. Mercury from the sample solution is reduced to elemental Hg by SnCl₂ and volatilized by the bubbles of a carrier gas. The gas containing mercury vapour is dried and passed through a capillary onto a gold coated graphite electrode. An anodic stripping voltam-mogram is recorded from 0.1 mol/1 HClO₄ + 3 × 10⁻³ mol/1 HCl solution. The calibration curve is linear from 1 × 10⁻⁹ to 4 × 10⁻⁸ mol/1 Hg(NO₃)₂. The absolute detection limit is 0.46 ng Hg. The relative standard deviations for 4 × 10⁻⁹ mol/1 and 2 × 10⁻⁸ mol/1 Hg(NO₃)₂ are 9.8% and 6.1%, respectively n = 5).     

Sensitive determination of nucleotides and polynucleotides based on the fluorescence quenching of the Tb3+-Tiron complex

 A sensitive method using fluorescence quenching for the determination of nucleotides (ATP, ADP, AMP, CTP, UTP) and polynucleotides[poly(A), poly(I), poly(U)] is proposed. It is based on the ability of nucleotides and polynucleotides to inhibit the formation of a strongly fluorescent complex of Tb³⁺ ion with Tiron. The possibilities of spectrofluorimetric measurements of these systems were studied under optimal conditions (pH 6.9 in hexamethylene tetramine-HCl buffer, 1.2×10^-6 mol/L of Tb³⁺, 4.0×10^-6 mol/L of Tiron, λ_ex=317 nm, λ_em=546 nm). The results showed that the Tb³⁺-Tiron complex could be used as a fluorescence test for the phosphate moieties of nucleotides and polynucleotides. The detection limits are 0.3, 1.2, 3.7, 0.2, 0.3, 1.1, 0.6 and 0.9 ng/mL for ATP, ADP, AMP, CTP, UTP, poly(A), poly(I), and poly(U), respectively. The relative standard deviations (6 replicates) are within 4.0% in the middle of the linear range. The fluorescence quenching mechanism of these systems is also discussed. Received: 16 July 1996 / Revised: 13 November 1996 / Accepted: 13 November 1996     

Solvent extraction of rare-earth metals with bis(2-ethylhexyl)phosphinic acid

 The extraction behavior of tervalent rare-earth metals (Ln) using a heptane solution containing bis(2-ethylhexyl)phosphinic acid (PIA-8, HR) from 0.1 mol/dm³ sodium perchlorate media was studied. The pH_0.5 values and separation factors obtained were compared among the metals. The stoichiometry of the extracted species and the extraction constants for the present aqueous/heptane system were determined by slope analysis. It is demonstrated that the rare-earth metals were extracted as monomers LnR₃⋅mHR (m=3, 4, 5 or 6), and the extracted species could be stripped into a relatively low concentrated hydrochloric acid. PIA-8 was found to be the most selective extractant for the mutual separation of rare-earth metals among the other phosphinic acids reported. Received: 27 February 1996/Revised: 13 May 1996/Accepted: 21 May 1996     

MFI纳米片沉积层气相转化制备超薄b轴取向沸石膜

利用乙二胺-水蒸汽进行气相转化(VPT)制备超薄、取向MFI沸石膜,通过将MFI纳米片沉积层转化为致密的沸石膜,实现了膜厚度的有效控制。扫描电子显微镜和X射线衍射表明,制备的沸石膜膜厚度约为280 nm,具有高度b轴取向的致密结构。丁烷异构体双组分分离测试结果表明,在333 K下,等物质的量的正丁烷/异丁烷混合物的正丁烷渗透速率和分离因子分别为1.5×10^-7 mol·m^-2·s^-1·Pa^-1和14.8。Na₂SiO₃作为低聚硅源在MFI沸石纳米片二次生长过程中能够提供硅源和碱度,通过在胺类蒸汽中实现MFI沸石纳米片间的融合生长,进一步提高了膜的取向度和致密性。     

Determination of nicotinamide (NA) using its polarographic catalytic wave in the presence of KIO3

Nicotinamide (NA) yields a polarographic catalytic wave with a peak potential –1.38 V (vs. SCE) in 0.1 mol/L HAc-NaAc (pH 4.7)/4 × 10^–3 mol/L KIO₃ buffer solution. The sensitivity of the catalytic wave increased in one order of magnitude as compared to that of the responding reduction wave without KIO₃. Based on this observation, a new method for the determination of NA was recommended. The second order derivative peak current was proportional to the NA concentration in the range of 5 × 10^–8 – 6 × 10^–7 mol/L. 0.11-fold vitamin B₁, 0.13-fold B₂, 0.14-fold B₆ and 8-fold nicotinic acid amounts do not interfere the determination of 1 × 10^–6 mol/L NA. The proposed method was used to determine the NA content in multivitamin tablets, with good agreement to the declared amount. Received: 25 October 1999 / Revised: 28 March 2000 / /Accepted: 31 March 2000     

Cathodic stripping voltammetric determination of selenium(IV) at a thin-film mercury electrode in a thiocyanate-containing electrolyte

The well-known method for the determination of selenium(IV), which is based on the cathodic stripping voltammetry of copper(I) selenide, has been adapted for application at the thin-film mercury electrode on glassy carbon (TFME). Insufficient reproducibility and sensitivity have been overcome by using a 0.1 mol/L HClO₄ electrolyte solution containing 0.02 mol/L thiocyanate ions. Thiocyanate ions have been found to increase the peak height of the selenium response and shift it to more positive potentials. This behaviour is explained by an adsorption of SCN^– at the interface glassy carbon/Cu₂Se and its action as an electron transfer catalyst between glassy carbon and copper(I) selenide. A 3σ-detection limit of 75 ng/L Se^(IV) has been achieved. The relative standard deviation is 5.2% at 5 μg/L selenium(IV). The influence of cadmium(II), arsenic(III), zinc(II), iron(III) and lead(II) ions on the selenium response has been studied. In case of lead ions, a new signal occurred at more negative potentials than the reduction of Cu₂Se. This signal, which is probably due to the reduction of PbSe, can also be used for the determination of selenium(IV). Received: 13 November 1996 / Revised: 19 December 1996 / Accepted: 24 December 1996     

MFI纳米片沉积层气相转化制备超薄b轴取向沸石膜

利用乙二胺-水蒸汽进行气相转化（VPT）制备超薄、取向MFI沸石膜,通过将MFI纳米片沉积层转化为致密的沸石膜,实现了膜厚度的有效控制。扫描电子显微镜和X射线衍射表明,制备的沸石膜膜厚度约为280 nm,具有高度b轴取向的致密结构。丁烷异构体双组分分离测试结果表明,在333 K下,等物质的量的正丁烷/异丁烷混合物的正丁烷渗透速率和分离因子分别为1.5×10^-7 mol·m^-2·s^-1·Pa^-1和14.8。Na₂SiO₃作为低聚硅源在MFI沸石纳米片二次生长过程中能够提供硅源和碱度,通过在胺类蒸汽中实现MFI沸石纳米片间的融合生长,进一步提高了膜的取向度和致密性。