Control of stereospecificity in the radical polymerization of N‐methyl‐N‐(2‐pyridyl)acrylamide by conformational switching of the monomer with protonation

Radical polymerization of N‐methyl‐N‐(2‐pyridyl)acrylamide (MPyAAm) was carried out in dichloromethane at low temperatures in the presence of trifluoroacetic acid (TFA). The m dyad contents of the polymers obtained at 0 °C increased linearly from 37 to 60% with an increase in the [TFA]₀/[MPyAAm]₀ ratio from 1 to 5. Nuclear magnetic resonance (NMR) analysis of MPyAAm–TFA mixtures in dichloromethane‐d₂ revealed that the favorable conformation in terms of the pyridyl group to the carbonyl group in MPyAAm switched from s‐trans to s‐cis by protonation. The results suggest that controlling the conformation of MPyAAm resulted in control of the stereospecificity in radical polymerization of the monomer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Hydrogen‐bond‐assisted stereocontrol in the radical polymerization of N‐isopropylacrylamide with primary alkyl phosphate: The effect of the chain length of the straight ester group

The radical polymerizations of N‐isopropylacrylamide (NIPAAm) were carried out in toluene at low temperatures in the presence of phosphoric acid esters such as trimethyl phosphate, triethyl phosphate (TEP), tri‐n‐propyl phosphate, and tri‐n‐butyl phosphate (TBP). Syndiotactically rich poly(NIPAAm)s were obtained from ?60 to 0 °C, and TEP provided the highest syndiotacticity (racemo dyad = 65%) at ?40 °C. On the other hand, lowering the temperature reversed the stereoselectivity of the propagation reaction so that isotactically rich poly(NIPAAm)s were obtained at ?80 °C. In particular, TBP exhibited the most isotactic specificity (meso dyad = 57%). Job's plots for NIPAAm–TBP mixtures revealed that NIPAAm and TBP formed a 1:1 complex at 0 °C and a predominantly 1:2 complex at ?80 °C through a hydrogen‐bonding interaction. Therefore, the stereospecificity of NIPAAm polymerization should depend on the stoichiometry of the hydrogen‐bond‐assisted complex. Thus, the mechanism for this polymerization system was discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 50–62, 2005     

Hydrogen‐bond‐assisted syndiotactic‐specific radical polymerizations of N‐alkylacrylamides: The effect of the N‐substituents on the stereospecificities and unusual large hysteresis in the phase‐transition behavior of aqueous solution of syndiotactic poly(N‐n‐propylacrylamide)

The radical polymerizations of N‐alkylacrylamides, such as N‐methyl‐(NMAAm), N‐n‐propyl‐(NNPAAm), N‐benzyl‐(NBnAAm), and N‐(1‐phenylethyl)acrylamides (NPhEAAm), at low temperatures were investigated in the absence or presence of hexamethylphosphoramide (HMPA) and 3‐methyl‐3‐pentanol (3Me3PenOH), which induced the syndiotactic specificities in the radical polymerization of N‐isopropylacrylamide (NIPAAm). In the absence of the syndiotactic‐specificity inducers, the syndiotacticities of the obtained polymers gradually increased as the bulkiness of the N‐substituents increased. Both HMPA and 3Me3PenOH induced the syndiotactic specificities in the NNPAAm polymerizations as well as in the NIPAAm polymerizations. The addition of 3Me3PenOH into the polymerizations of NMAAm significantly induced the syndiotactic specificities, whereas the tacticities of the obtained polymers were hardly affected by adding HMPA. In the polymerizations of bulkier monomers, such as NBnAAm and NPhEAAm, HMPA worked as the syndiotactic specificity inducer at higher temperatures, whereas 3Me3PenOH hardly influenced the stereospecificity, regardless of the temperatures. The phase‐transition behaviors of the aqueous solutions of poly(NNPAAm)s were also investigated. It appeared that the poly (NNPAAm) with racemo dyad content of 70% exhibited unusual large hysteresis between the heating and cooling processes. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4575–4583, 2008     

Stereospecific radical polymerization of N‐tert‐butoxycarbonylacrylamide in the presence of fluorinated alcohols

Radical polymerization of N‐tert‐butoxycarbonylacrylamide (NBocAAm) in toluene at low temperatures in the presence of the fluorinated alcohols, 2,2,2‐trifluoroethanol, 1,1,1,3,3,3‐hexafluoro‐2‐propanol, and nonafluoro‐tert‐butanol, afforded atactic, heterotactic, and syndiotactic polymers, respectively. NMR analysis revealed that the fluorinated alcohols formed hydrogen bonding‐assisted complexes with NBocAAm, with different structures. The difference in the structures of the complexes was responsible for the differences in the induced stereospecificities. Based on the structures of the complexes between NBocAAm and the fluorinated alcohols, mechanisms for the three kinds of stereospecific radical polymerizations are proposed. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Syndiotactic‐specific radical polymerization of N,N‐dimethylacrylamide in the presence of tartrates: A proposed mechanism for the polymerization

Radical polymerization of N,N‐dimethylacrylamide (DMAAm) was investigated in the presence of tartrates, such as diethyl L ‐tartrate, diisopropyl L ‐tartrate, and di‐n‐butyl L ‐tartrate, in toluene at low temperatures. Syndiotactic polymers were obtained in the presence of tartrates, whereas isotactic polymers were obtained in the absence of tartrates. The syndiotactic‐specificity increased with increasing amount of tartrates and with decreasing polymerization temperature. NMR analysis suggested that DMAAm and tartrates formed a 1:1 complex through double hydrogen bonding. A mechanism for the syndiotactic‐specific radical polymerization of DMAAm is proposed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1192–1203, 2009     

Syndiotactic‐ and heterotactic‐specific radical polymerizations of N‐n‐propyl‐α‐fluoroacrylamide and phase‐transition behaviors of aqueous solutions of poly(N‐n‐propyl‐α‐fluoroacrylamide)

Radical polymerization of N‐n‐propyl‐α‐fluoroacrylamide (NNPFAAm) was investigated in several solvents at low temperatures in the presence or absence of Lewis bases, Lewis acids, alkyl alcohols, silyl alcohols, or fluorinated alcohols. Different effects of solvents and additives on stereospecificity were observed in the radical polymerizations of NNPFAAm and its hydrocarbon analogs such as N‐isopropylacrylamide (NIPAAm) and N‐n‐propylacrylamide (NNPAAm); for instance, syndiotactic (and heterotactic) specificities were induced in radical polymerization of NNPFAAm in polar solvents (and in toluene in the presence of alkyl and silyl alcohols), whereas isotactic (and syndiotactic) specificities were induced in radical polymerizations of the hydrocarbon analogs under the corresponding conditions. In contrast, heterotactic specificity induced by fluorinated alcohols was further enhanced in radical polymerization of NNPFAAm. The effects of stereoregularity on the phase‐transition behaviors of aqueous solutions of poly(NNPFAAm) were also investigated. Different tendencies in stereoregularity were observed in aqueous solutions of poly(NNPFAAm)s from those in solutions of the hydrocarbon analogs such as poly(NIPAAm) and poly (NNPAAm). The polymerization behavior of NNPFAAm and the phase‐transition behavior of aqueous poly(NNPFAAm) are discussed based on possible fluorine–fluorine repulsion between the monomer and propagating chain‐end, and neighboring monomeric units. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Hydrogen‐bond‐assisted stereocontrol in the radical polymerization of N‐isopropylacrylamide with secondary alkyl phosphate: The effect of the bulkiness of the ester group

The radical polymerization of N‐isopropylacrylamide (NIPAAm) in toluene at low temperatures was investigated in the presence of triisopropyl phosphate (TiPP). The addition of TiPP induced a syndiotactic specificity that was enhanced by the polymerization temperature being lowered, whereas atactic polymers were obtained in the absence of TiPP, regardless of the temperature. Syndiotactic‐rich poly(NIPAAm) with a racemo dyad content of 65% was obtained at ?60 °C with a fourfold amount of TiPP, but almost atactic poly(NIPAAm)s were obtained by the temperature being lowered to ?80 °C. This result contrasted with the result in the presence of primary alkyl phosphates, such as tri‐n‐propyl phosphate: the stereospecificity varied from syndiotactic to isotactic as the polymerization temperature was lowered. NMR analysis at ?80 °C revealed that TiPP predominantly formed a 1:1 complex with NIPAAm, although primary alkyl phosphates preferentially formed a 1:2 complex with NIPAAm. Thus, it was concluded that a slight increase in the bulkiness of the added phosphates influenced the stoichiometry of the NIPAAm–phosphate complex at lower temperatures, and consequently a drastic change in the effect on the stereospecificity of NIPAAm polymerization was observed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3899–3908, 2005     

Heterotactic‐specific radical polymerization of N‐isopropylacrylamide and phase transition behavior of aqueous solution of heterotactic poly(N‐isopropylacrylamide)

Radical polymerization of N‐isopropylacrylamide (NIPAAm) in toluene at low temperatures, in the presence of fluorinated‐alcohols, produced heterotactic polymer comprising an alternating sequence of meso and racemo dyads. The heterotacticity reached 70% in triads when polymerization was carried out at ?40 °C using nonafluoro‐tert‐butanol as the added alcohol. NMR analysis revealed that formation of a 1:1 complex of NIPAAm and fluorinated‐alcohol through C?O···H? O hydrogen bonding induces the heterotactic specificity. A mechanism for the heterotactic‐specific polymerization is proposed. Examination of the phase transition behavior of aqueous solutions of heterotactic poly(NIPAAm) revealed that the hysteresis of the phase transition between the heating and cooling cycles depended on the average length of meso dyads in poly(NIPAAm). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2539–2550, 2009     

Atom transfer radical polymerization initiated by N‐bromosuccinimide

N‐Bromosuccinimide (NBS) was used as the initiator in the atom transfer radical polymerizations of styrene (St) and methyl methacrylate (MMA). The NBS/CuBr/bipyridine (bpy) system shows good controllability for both polymerizations and yields polymers with polydispersity indexes ranging from 1.18 to 1.25 for St and 1.14 to 1.41 for MMA, depending on the conditions used. The end‐group analysis of poly(MMA) and polystyrene indicated the polymerization is initiated by the succinimidyl radicals formed from the redox reaction of NBS with CuBr/bpy. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5811–5816, 2004     

Simultaneous control of the stereospecificity and molecular weight in the ruthenium‐catalyzed living radical polymerization of methyl and 2‐hydroxyethyl methacrylates and sequential synthesis of stereoblock polymers

The stereospecific living radical polymerizations of methyl methacrylate (MMA) and 2‐hydroxyethyl methacrylate (HEMA) were achieved with a combination of ruthenium‐catalyzed living radical and solvent‐mediated stereospecific radical polymerizations. Among a series of ruthenium complexes [RuCl₂(PPh₃)₃, Ru(Ind)Cl(PPh₃)₂, and RuCp*Cl(PPh₃)₂], Cp*–ruthenium afforded poly(methyl methacrylate) with highly controlled molecular weights [weight‐average molecular weight/number‐average molecular weight (M_w/M_n) = 1.08] and high syndiotacticity (r = 88%) in a fluoroalcohol such as (CF₃)₂C(Ph)OH at 0 °C. On the other hand, a hydroxy‐functionalized monomer, HEMA, was polymerized with RuCp*Cl(PPh₃)₂ in N,N‐dimethylformamide and N,N‐dimethylacetamide (DMA) to give syndiotactic polymers (r = 87–88%) with controlled molecular weights (M_w/M_n = 1.12–1.16). This was the first example of the syndiospecific living radical polymerization of HEMA. A fluoroalcohol [(CF₃)₂C(Ph)OH], which induced the syndiospecific radical polymerization of MMA, reduced the syndiospecificity in the HEMA polymerization to result in more or less atactic polymers (mm/mr/rr = 7.2/40.9/51.9%) with controlled molecular weights in the presence of RuCp*Cl(PPh₃)₂ at 80 °C. A successive living radical polymerization of HEMA in two solvents, first DMA followed by (CF₃)₂C(Ph)OH, resulted in stereoblock poly(2‐hydroxyethyl methacrylate) with syndiotactic–atactic segments. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3609–3615, 2006     

Atom transfer radical polymerization through N‐chlorosulfonamides

Controlled polymerizations of vinyl monomers such as methyl methacrylate and styrene are achieved using N‐chloro,N‐propyl‐p‐toluenesulfonamide (NCPT) together with a cuprous bromide/hexahexyl triethylenetetramine (CuBr/H‐TETA) complex. Although N‐halosulfonamides are known to decompose radically to give free chlorine, NCPT alone (without a cuprous complex) does not initiate any polymerization even in prolonged reaction times. Instead these add to the double bonds to give 2‐chloroethylsulfonamides. In the present polymerization system a good chlorine donator (NCPT) is combined with an organic soluble complex (CuBr/H‐TETA) to perform atom transfer radical polymerizations (ATRPs) in homogenous conditions. The linear proportionality of the molecular weights to the conversions and straight lines observed in ln(M₀/M) (where M₀ and M are the monomer contents at the beginning and at any time, respectively) versus time plots indicate typical controlled polymerization characteristics. The use of freshly prepared NCPT is advisable due to its slow and spontaneous decomposition when standing at room temperatures. Because of their easy preparation, N‐chlorosulfonamides can be used and are preferred instead of special halogen compounds commonly used in copper mediated ATRP. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2691–2695, 2001     

Stereocontrol during the free‐radical polymerization of methacrylamides in the presence of Lewis acids

The effects of Lewis acids, that is, rare earth metal trifluoromethanesulfonates, on the free‐radical polymerization of N‐methylmethacrylamide (MMAM), N‐isopropylmethacrylamide (IPMAM), N‐tert‐butylmethacrylamide (tBMAM), N‐phenylmethacrylamide (PMAM), and methacrylamide were examined under various conditions. A catalytic amount of Yb(OSO₂CF₃)₃ significantly affected the stereochemistry during the radical polymerization. Polymerization solvents strongly influenced the effect of the Lewis acids. Methanol was the best solvent for increasing the isotactic specificity during the polymerization of MMAM and IPMAM, whereas tetrahydrofuran was more effective for the tBMAM and PMAM polymerizations. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1027–1033, 2003     

End‐group fidelity in nitroxide‐mediated living free‐radical polymerizations

In this study, new nitroxides based on the 2,2,5‐trimethyl‐4‐phenyl‐3‐azahexane‐3‐oxy skeleton were used to examine chain‐end control during the preparation of polystyrene and poly(t‐butyl acrylate) under living free‐radical conditions. Alkoxyamine‐based initiators with a chromophore attached to either the initiating fragment or the mediating nitroxide fragment were prepared, and the extent of the incorporation of the chromophores at either the initiating end or the propagating chain end was determined. In contrast to 2,2,6,6‐tetramethyl piperidinoxy (TEMPO), the incorporation of the initiating and terminating fragment into the polymer chain was extremely high. For both poly(t‐butyl acrylate) and polystyrene with molecular weights less than or equal to 70,000, incorporations at the initiating end of greater than 97% were observed. At the terminating chain end, incorporations of greater than 95% were obtained for molecular weights less than or equal to 50,000. The level of incorporation tended to decrease slightly at higher molecular weights because of the loss of the alkoxyamine propagating unit, which had important consequences for block copolymer formation. These results clearly show that these new α‐H nitroxides could control the polymerization of vinyl monomers such as styrene and t‐butyl acrylate to an extremely high degree, comparable to anionic and atom transfer radical polymerization procedures. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4749–4763, 2000     

Synthesis of bio‐based poly(N‐phenylitaconimide) by atom transfer radical polymerization

Poly(N‐phenylitaconimide) (polyPhII) was prepared using initiators for continuous activator regeneration atom transfer radical polymerization of PhII using FeBr₃ complexes as catalysts. Conversion reached 69% in 24 h, yielding polyPhII with a number average molecular weight M_n = 11,900 and a molecular weight distribution M_w/M_n = 1.52. Copolymerizations of PhII with styrene at various molar ratios were performed providing a range of polyPhII‐copolySt polymers. When the copolymerization was carried out with higher [St]₀ > [PhII]₀ ratio, a one‐pot synthesis of poly(St‐alt‐PhII)‐b‐polySt was achieved. The thermal properties of the obtained copolymers were studied by differential scanning calorimetry. PolyPhII prepared by ATRP showed high glass transition temperature (T_g) of 216 °C and the poly(St‐alt‐PhII)‐b‐polySt exhibited two T_gs, at 162 and 104 °C, corresponding to a poly(St‐alt‐PhII) and polySt segments, respectively. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 822–827     

Rapid additive‐free TEMPO‐mediated stable free radical polymerizations of styrene

The stable free radical polymerization (SFRP) of styrene, initiated with benzoyl peroxide in the presence of TEMPO, under bulk conditions, is demonstrated to proceed rapidly without the need for any rate enhancing additives such as camphorsulfonic acid, 2‐fluoro‐1‐methyl pyridinium p‐toluenesulfonate, or acetic anhydride. Monomer conversions as high as 70% can be achieved in 5 h or less while maintaining polydispersity indexes of 1.15. These results stand in stark contrast to earlier reactions that required 70 h to achieve similar conversions. This study demonstrates that the single largest factor governing the rates of polymerization is the molar concentration of excess TEMPO remaining in solution after initiation. A reduction in the TEMPO to BPO ratio is required when large amounts of BPO are used to target low molecular weight polystyrenes. However, when a lower molar amount of BPO is used to obtain high molecular weight polystyrenes, a higher TEMPO to BPO ratio is required. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5487–5493, 2007     

Radical polymerization of novel N‐substituted‐N‐vinylformamide derivatives with bulky chiral substitutents

A series of novel N‐substituted‐N‐vinylformamides were synthesized, and the effect of bulky substituents on their radical polymerizability and polymer structure were investigated. N‐(p‐Methoxybenzyl)‐N‐vinylformamide ( 3 ) and N‐cyclohexylmethyl‐N‐vinylformamide ( 4 ) generated polymers, while it was known that their N‐vinylacetamide derivatives did not. ¹H NMR and ¹³C NMR analyses of poly( 3 ), however, revealed almost no difference among the various polymerization conditions, implying that the substituent bulkiness did not influence the polymer structures. On the other hand, the chiral polymers, which were obtained by the radical polymerization of N‐(S)‐2‐methylbutyl‐N‐vinylformamide ((S)‐ 5 ) and N‐(S)‐2,3‐dihydroxypropyl‐N‐vinylformamide ((S)‐ 7 ) at 0 °C, showed sharper spectral patterns than those obtained at higher polymerization temperatures. Furthermore, the intensities of their positive cotton effects on circular dichroism increased when the polymerization temperature was low, suggesting that the substituent bulkiness of (S)‐ 5 and (S)‐ 7 influenced the polymer structures, such as their stereoregularity and regioregularity. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012