Extraordinary transport behavior of gases in isothermally annealed poly(4‐methyl‐1‐pentene) membranes

Poly(4‐methyl‐1‐pentene) (PMP) membranes were modified through isothermal annealing to investigate the change of their crystalline structure and rigid and mobile amorphous fractions (RAF and MAF), assuming a three‐phase model, affected the gas transport behavior. The crystalline structure was characterized by wide‐angle X‐ray diffraction (WAXD) and small‐angle X‐ray scattering (SAXS) techniques, and the free volume properties were analyzed by positron annihilation lifetime spectroscopy. Compared with the pristine membrane, the annealed membranes show higher crystallinity; the crystals undergo partial structural change from form III to form I. The lamellar crystal thickness, rigid amorphous fraction thickness, and long period in the lamellar stacks increase with crystallinity. The annealed PMP membranes exhibit higher permeability due to the increase in larger size free volumes in MAF and higher selectivity due to the increase in smaller size free volumes in RAF, respectively. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2368–2376     

Blends of poly(3‐hydroxybutyrate)/4,4′‐thiodiphenol and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/ 4,4′‐thiodiphenol: Specific interaction and properties

The specific interaction between poly(3‐hydroxybutyrate) [P(3HB)] and 4,4′‐thiodiphenol (TDP) and between poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) and TDP was investigated by Fourier transform infrared (FTIR) spectroscopy. Interassociated hydrogen bonds were found between the polyester chains and the TDP molecules in the binary blends. The fractions of associated carbonyl groups, F_b 's, in the blends first increased and then decreased as the TDP content increased. The thermal and dynamic mechanical properties of P(3HB)–TDP and PHBV–TDP blends were investigated by differential scanning calorimetry and dynamic mechanical thermal analysis, respectively. Thermal analysis revealed that the P(3HB)–TDP blends possessed eutectic phase behavior. Furthermore, it was found that the thermal and dynamic mechanical properties of P(3HB) and PHBV were greatly modified through blending with TDP. Environmental degradability in river water was evaluated by a biochemical oxygen demand tester, and it was clarified that TDP lowered the degradation rate of P(3HB). The results suggest that TDP is effective in modifying the physical properties as well as the biodegradability of polyesters. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2891–2900, 2000     

Polyurethanes from polyols obtained by ADMET polymerization of a castor oil‐based diene: Characterization and shape memory properties

The acyclic diene metathesis polymerization (ADMET) of 1,3‐di‐10‐undecenoxy‐2‐propanol, a castor oil based diene, is reported. 10‐Undecenol was used as renewable comonomer to end‐cap polymer chains and limit the molecular weight. The poly ols obtained in this way were reacted with 4,4′‐methylenebis(phenylisocyanate) (MDI) to yield a series of amorphous and semicrystalline polyurethane networks. The thermal stability and the thermomechanical and mechanical properties of these thermosets have been studied and showed good shape memory properties for the semicrystalline polymer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Effect of orientation on the free volume and oxygen transport of a polypropylene copolymer

The effect of uniaxial orientation on the free‐volume and oxygen‐transport properties of a propylene copolymer with 4.5 wt % ethylene was examined. The free‐volume hole size and hole density were measured with positron annihilation lifetime spectroscopy. Subsequently, the free‐volume characteristics were correlated with the oxygen‐transport properties. Orientation had only a small effect on the total amount of free volume: a small increase in the hole density was offset by a small decrease in the hole size. As a result, the oxygen solubility and amorphous‐phase density were unchanged by orientation. However, a pronounced decrease in the oxygen diffusivity when the draw ratio exceeded 6 indicated a change in the dynamic free volume. This was attributed to an increasing number of taut tie chains, which retarded oxygen diffusion. The reduced amorphous chain mobility was also manifest in the increased glass‐transition temperature, decreased bulk thermal expansivity, and decreased expansivity of free‐volume holes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1230–1243, 2005     

Transformation of isotactic polypropylene droplets from the mesophase into the α‐phase

The structural transformation of homogeneously nucleated metastable mesophase of polypropylene (PP) particles was investigated in this study. We demonstrated the formation of heterogeneity‐free mesophase by slow cooling of the droplets unlike mesophase formation by quenching of the PP melt, which contained large number of bulk nuclei. Submicron size PP droplets were produced by thermal break up of PP and polystyrene layered film assembly. When cooled from melt, the PP droplets crystallized into mesophase at 44 °C revealing granular morphology. Subsequent heating thermogram of the PP particles showed a broad exotherm, which was attributed to the transformation of mesophase into α‐phase. This transformation was investigated during heating by annealing the PP particles at different temperatures. Annealed PP particles were analyzed by means of thermal, morphological and structural properties measurements. Results revealed a two step process for the transformation process. In the first step, the internal rearrangement of PP chains, as against melting and recrystallization of the mesophase, was observed. Since granular morphology was not affected significantly up to 120 °C, it was suggested that translational and rotational motions of PP helices produced ordered α‐phase. In the second step, increment in grain size distribution was observed, when the droplets were annealed at 140 °C. The results were attributed to enhanced chain mobility and merging of the grain boundaries. Annealing at 160 °C revealed the formation of short lamellar structures. Crystal thickening, melting and recrystallization of α‐phase were suggested at high temperature annealing. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Lamellar morphology and equilibrium melting temperature of syndiotactic polystyrene in β‐crystalline form

Lamellar morphology and thickness of syndiotactic polystyrene (sPS) samples melt‐crystallized at various temperatures were probed using transmission electron microscopy (TEM) and small‐angle X‐ray scattering (SAXS). In addition, the melting temperature and enthalpy of the crystallized samples were characterized with differential scanning calorimetry. Under appropriate thermal treatments, all the samples investigated in this study were crystallized into β′ crystal modification, as revealed by wide‐angle X‐ray diffraction. From the SAXS intensity profiles, a scattering peak (or shoulder) associated with lamellar features as well as the presence of anomalous scattering at the zero‐scattering vector were evidently observed. The peculiar zero‐angle scattering was successfully described by the Debye–Bueche model, and subtraction of its contribution from the raw intensity profiles was carried out to deduce the intensity profile merely associated with the lamellar feature. The lamellar thickness obtained from Lorentz‐corrected intensity profiles in this manner agrees with that measured from the TEM images, provided that the two‐phase model is applied. On the basis of the Gibbs–Thomson equation, the modest estimations of equilibrium melting temperature and the surface free energy of the fold lamellar surface are 292.7 ± 2.7 °C and 20.2 ± 2.6 erg/cm², respectively, when lamellar thicknesses measured by TEM are applied. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1626–1636, 2002     

The brittle–ductile transition induced by thermal ageing of toluene cast poly(2,6‐dimethyl‐1,4‐phenylene oxide) as observed by interfacial friction

The interfacial shear stress of toluene cast poly(2,6‐dimethyl‐1,4‐phenylene oxide) films has been studied as a function of annealing temperature. The surface topography of these films was studied by scanning probe microscopy following a single sliding pass. Casting from toluene results in a semicrystalline film with a rigid amorphous phase and containing a small amount of residual solvent that exhibits a higher interfacial shear stress than a high temperature annealed solvent‐free amorphous film. Films containing small amounts of toluene exhibit a wear pattern consisting of ripples oriented perpendicular to the sliding direction following a single sliding pass. These results support the notion that the interfacial shear stress is a function of the shear yield stress, and, that during sliding friction tensile stresses must form at the polymer surface. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1637–1643, 2009     

Initial lamellar thickness dependency of recrystallization behavior of poly(4‐methyl‐1‐pentene)

The isothermal crystallization and subsequent melting process in semicrystalline poly(4‐methyl‐1‐pentene) were investigated via temperature‐dependent small‐ and wide‐angle X‐ray scattering and Flash DSC techniques. In a phase diagram of inversed crystalline lamellar thickness and temperature, the crystallization and melting lines can be described by two linear dependencies of different slopes and different limiting temperatures at infinite lamellar thickness. Upon subsequent heating, recrystallization lines with different slopes were observed for samples with different lamellar thickness, indicating changes in surface free energy difference between stabilized crystallites and mesomorphic phase. The surface free energy of native crystallites with extended‐chain conformation decreased with increasing lamellar thickness due to a more ordered surface region and less chain ends which changes cooperatively with mesomorphic phase. The surface free energy of stabilized crystallites remained unchanged for all lamellar thickness. Therefore, the recrystallization lines with different slopes are consequences of changes in surface free energy of mesomorphic phase. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 219–224     

Elevation of the glass transition temperature in flexible‐chain semicrystalline polymers

In the idealized two‐phase model of a semicrystalline polymer, the amorphous intercrystalline layers are considered to have the same properties as the fully‐amorphous polymer. In reality, these thin intercrystalline layers can be substantially influenced by the presence of the crystals, as individual polymer molecules traverse both crystalline and amorphous phases. In polymers with rigid backbone units, such as poly(etheretherketone), PEEK, previous work has shown this coupling to be particularly severe; the glass transition temperature (T_g) can be elevated by tens of degrees celsius, with the magnitude of the elevation correlating directly with the thinness of the amorphous layer. However, this connection has not been explored for flexible‐chain polymers, such as those formed from vinyl‐type monomers. Here, we examine T_g in both isotactic polystyrene (iPS) and syndiotactic polystyrene (sPS), crystallized under conditions that produce a range of amorphous layer thicknesses. T_g is indeed shown to be elevated relative to fully‐amorphous iPS and sPS, by an amount that correlates with the thinness of the amorphous layer; the magnitude of the effect is severalfold less than that in PEEK, consistent with the minimum lengths of polymer chain required to make a fold in the different cases. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1198–1204, 2007     

Novel etching phenomena in poly(3‐hydroxy butyrate) and poly(oxymethylene) spherulites

Poly‐3‐hydroxy butyrate has been etched and studied under scanning and transmission electron microscopes. It displays three of the following unusual features: (1) spherulites develop in a loose spiral rather than radial structure, which appears to reflect the chiral nature of the polymer; (2) in the banded spherulitic structure, lamellae oriented flat‐on to the surface are etched more deeply in relation to edge‐on lamellae; and (3) material crystallized at high temperature is less resistant to etching than that crystallized at low temperature, whereas the most rapid rate of etching appears to be where growth occurred at an intermediate temperature where the growth rate was at its maximum. The second and third phenomena are contrary to what is found in polymers such as polyethylene and polyethylene terephthalate and are attributed to excess free volume in the material located between the main lamellar bundles. Polyoxymethylene also displays the same unusual relationship of etching rate with crystallization temperature. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 124–133, 2002     

Synthesis and characterizations of hemiditactic homopolymers derived of poly(3‐allyl‐3‐methylmalic acid): An example of a new class of polymer's ditacticity

A number of works have been focused on the study of polymers microtacticity and the probability of iso‐, syndio‐, and atactic arrangement of monomers such as polypropylene and poly(methacrylic esters) before the 1980s. This type of study was fewer in the last four decades despite the importance of stereochemical knowledge of macromolecules in the biomedical field. NMR analysis was the invaluable tool for the study of stereochemistry. This work detailed the synthesis and the physicochemical and microtacticity characterizations of new semicrystalline and amorphous polyesters, poly(3‐allyl‐3‐methylmalic acid) (PAlMMLA) derivatives which are part of the poly(malic acid) family. This polymer is biodegradable and biocompatible. It can also be chemically modified for a possible combination with bioactive molecules. It can be synthesized from chiral product leading a stereoregular and semicrystalline structure. In the case of a racemic starting product, the obtained macromolecular structure is amorphous. Semi‐crystalline polyester presented a highly diisotactic structure. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2408–2418     

Free volume and oxygen transport in cold‐drawn polyesters

Poly(ethylene terephthalate) (PET), poly(ethylene terephthalate‐co‐4,4′‐bibenzoate) (PETBB55), and poly(ethylene 2,6‐naphthalate) (PEN) were cold‐drawn to achieve uniform extension without crystallization or stress whitening, and oxygen transport properties were studied at temperatures from 10 to 40 °C. Correlation of oxygen solubility and polymer specific volume made it possible to consider the oriented polyester as a one‐phase densified glass. Orientation was viewed as decreasing the amount of excess‐hole free volume and bringing the nonequilibrium polymer glass closer to the equilibrium condition. Between 10 and 40 °C, the amount of excess‐hole free volume in PET decreased as the polymer approached the glass transition temperature. In contrast, temperature changes in this range had little effect on the excess‐hole free volume in PETBB55 and PEN, which were well below their glass transition temperature. Gas diffusion was viewed as discrete jumps of the oxygen molecule between holes of excess‐free volume. The jump length was extracted from the activation energy for diffusion according to a channel‐formation model. The result agreed well with the hole spacing estimated from a simple lattice model using the hole density reported in the literature. Extending the lattice model to estimate the mean excess‐free volume hole radius from the fractional free volume resulted in good correlation with the hole radius obtained from positron annihilation lifetime spectroscopy. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 493–504, 2004     

Studies on poly(ε‐caprolactone)/thiodiphenol blends: The specific interaction and the thermal and dynamic mechanical properties

The effects of several low molecular weight compounds with hydroxyl groups on the physical properties of poly(ε‐caprolactone) (PCL) were investigated by Fourier transform infrared (FTIR) spectroscopy and high‐resolution solid‐state ¹³C NMR. PCL and 4,4′‐thiodiphenol (TDP) interact through strong intermolecular hydrogen bonds and form hydrogen‐bonded networks in the blends at an appropriate TDP content. The thermal and dynamic mechanical properties of PCL/TDP blends were investigated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis, respectively. The melting point of PCL decreased, whereas both the glass‐transition temperature and the loss tangent tan δ of the blend increased with an increase in TDP content. The addition of 40 wt % TDP changed PCL from a semicrystalline polymer in the pure state to a fully amorphous elastomer. The molecules of TDP lost their crystallizability in the blends with TDP contents not greater than 40 wt %. In addition to TDP, three other PCL blend systems with low molecular weight additives containing two hydroxyl groups, 1,4‐dihydroxybenzene, 1,4‐di‐(2‐hydroxyethoxy) benzene, and 1,6‐hexanediol, were also investigated with FTIR and DSC, and the effects of the chemical structure of the additives on the morphology and thermal properties are discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1848–1859, 2000     

Impact of average free‐volume element size on transport in stereoisomers of polynorbornene. I. Properties at 35 °C

This article demonstrates that transport of gases through glassy polymers is significantly influenced not only by the absolute amount but also by the distribution of free volume. Two stereoisomers of polynorbornene with nearly equivalent total free volume, but markedly different average free‐volume sizes, were evaluated. The free‐volume element size was probed with positron annihilation lifetime spectroscopy, wide‐angle X‐ray scattering, gas sorption, and molecular modeling. The permeation, sorption, and diffusion of light gases were measured in each stereoisomer at 35 °C. All analytical techniques indicated that one isomer (labeled as Architecture II) had a larger average free‐volume element size but fewer elements. This isomer also had a very slightly higher bulk density (1.000 vs 0.992 g/cm³ for the other stereoisomer). Architecture II also had gas sorption and diffusion coefficients that were two to three times those of the less dense counterpart. These differences have been attributed to differences in the free‐volume element size available within the polymer matrix. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2185–2199, 2003     

Thermal and infrared spectroscopic studies on hydrogen‐bonding interactions between poly‐(ε‐caprolactone) and some dihydric phenols

The effects of three dihydric phenols on the thermal properties of poly‐(ε‐caprolactone) (PCL) were investigated by DSC. The thermal properties of PCL were found to be greatly modified by the addition of 4,4′‐dihydroxydiphenyl ether (DHDPE). When the content of DHDPE reached 40%, PCL that was a semicrystalline polymer in the pure state changed to a fully amorphous elastomer. Fourier transform infrared (FTIR) spectroscopy was also applied to investigate the specific interaction between PCL and DHDPE. The formations of intermolecular hydrogen bonds between the carbonyl groups of PCL and the hydroxyl groups of DHDPE were discovered. By applying the Beer–Lambert law and a curve‐fitting program, the fractions of hydrogen‐bonded carbonyl groups were quantitatively analyzed. Although one DHDPE molecule had the potentiality to form two hydrogen bonds with PCL chains, the values of the fraction of the hydroxyl group involved in the intermolecular hydrogen bond were so little that from a statistical point of view, the formation of two hydrogen bonds was very difficult for every DHDPE molecule. Both DSC and FTIR revealed that 4,4′‐dihydroxydiphenyl methane and 4,4′‐dihydroxyphenyl had the ability to form hydrogen bonds with PCL, which were strongly affected by the polarity of the group linking two hydroxyphenyls and the flexibility of the molecular chain. The stronger the polarity of the group and the better the flexibility of molecular chain, the more tendencies dihydric phenol had to form intermolecular hydrogen bonds with PCL. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2108–2117, 2001     

Crystallization and morphology of poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) blends. III. Crystallization and phase diagram by differential scanning calorimetry

The crystallization of poly(vinylidene fluoride) (PVDF)/poly(3‐hydroxybutyrate) (PHB) blends was studied with differential scanning calorimetry, from which the phase diagram was derived. Strong miscibility was underlined by the large negative Flory–Huggins interaction parameter (?0.25). The crystallization of the blend components differed remarkably. Whereas PVDF always crystallized in the surroundings of a homogeneous melt, PHB crystallized in a volume that was confined by the already existing PVDF spherulites, partly in their surroundings and partly inside. Under isothermal conditions, PVDF usually crystallized regularly in three dimensions with predominant quench‐induced athermal nucleation. The Avrami exponent for PVDF dendritic spherulitic growth was, however, distinctly smaller than that for compact growth, and this revealed the two‐dimensional lamellar growth inside. This deviation from ideal Avrami behavior was caused by the development of compositional inhomogeneities as PVDF crystallization proceeded, and this decelerated the kinetics. PHB crystallized three‐dimensionally with mixed thermal and athermal nucleation outside the PVDF spherulites. Inside the PVDF spherulites, PHB crystallization proceeded in a fibrillar fashion with thermal nucleation; the growth front followed the amorphous paths inside the dendritic PVDF spherulites. The crystallization was faster than that in the melt of uncrystallized PVDF. Solid PVDF acts possibly heterogeneously nucleating, accelerating PHB crystallization. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 287–295, 2005     

Poly(1,4‐cyclohexylenedimethylene 1,4‐cyclohexanedicarboxylate): Influence of stereochemistry of 1,4‐cyclohexylene units on the thermal properties

A series of poly(1,4‐cyclohexylenedimethylene 1,4‐cyclohexanedicarboxylate) (PCCD) samples, characterized by different cis/trans ratio of the 1,4‐cyclohexanedicarbonyl unit, have been synthesized and analyzed by thermogravimetry (TGA), calorimetry (DSC), and X‐ray diffraction (WAXD). The thermal stability results are good and are not affected by the stereochemistry of the 1,4‐cyclohexylene units. On the other hand, the thermal transitions are notably influenced by the cis/trans content. With the increment of the trans content the polymer changes from completely amorphous to semicrystalline material. T_g, T_m, and crystallinity increase. These results suggest that the trans configuration induces a better chain packing and higher symmetry, improving the crystallizability of the samples. The effect of the molecular structure on the thermal properties is analyzed by using a statistical approach. From the effective correlations found between stereochemistry of the C₆ rings and transition temperatures it is possible to extrapolate that the configuration of 1,4‐cyclohexylene ring deriving from 1,4‐cyclohexanedicarboxylic acid or dimethyl 1,4‐cyclohexanedicarboxylate results to be the main element responsible for the thermal properties. This is due to the high rigidity of the 1,4‐cyclohexanedicarbonyl unit with respect to 1,4‐cyclohexanedimethyleneoxy unit, deriving from the diol. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 619–630, 2008     

Poly‐2‐oxazoline‐derived polyurethanes: A versatile synthetic approach to renewable polyurethane thermosets

2‐Nonyl‐2‐oxazoline and 2‐(9‐decenyl)‐2‐oxazoline have been copolymerized in different proportions by cationic ring‐opening polymerization to obtain a series of random linear copolymers with tailored molecular weight and double bond functionality in the side chains. Thiol‐ene addition of 2‐mercaptoethanol has been used to produce a set of polyoxazoline–polyols under mild conditions and with quantitative double bond transformation. The polyols obtained in this way were reacted with methylene‐bis(phenylisocyanate) to yield a series of amorphous and semicrystalline polyurethane networks. The thermal stability and the thermomechanical properties of these thermosets have been studied and related with the structure of the parent polyols. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Deformation in lamellar and crystalline structures: in situ simultaneous small‐angle X‐ray scattering and wide‐angle X‐ray diffraction measurements on polyethylene terephthalate fibers

Changes in the lamellar and crystalline structures were followed as a function of applied stress to understand the influence of the interactions between the crystalline and amorphous domains on the fiber properties. We observed a reversible transformation from a structure giving a four‐point small‐angle pattern to a structure giving a two‐point pattern; these structures corresponded to the lamellae with oblique and normal lamellar surfaces, respectively. The characteristics of these two structures such as the stack diameter, stack height, and tilt angle were different and were determined by the processing conditions and did not change when the fiber was elastically deformed. The structure giving a two‐point pattern was probably the load‐carrying lamellar entity in these fibers. The diameter of the lamellar stacks, tilt angle of the lamellae, and the strain in the lamellar spacing appeared to have the most influence on properties such as tenacity and dimensional stability. The long‐spacing strain, which is about the same as the fiber strain, determined the modulus at low elongation as well as ultimate elongation. These indicate that the lamellar stacks have at least as much influence as the interfibrillar chains on fiber properties. Structural features that determine the performance in semicrystalline polymers were investigated by analyzing four generations of polyethylene terephthalate fibers. Some of the fiber properties correlate with changes in the crystalline domains such as the crystalline orientation, size, and unit cell dimensions. Fibers in which the crystalline strain was large because of their strong linkages to the amorphous chains, and better load transfer, had the highest modulus and lowest ultimate elongation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1538–1553, 2003     

Effects of amorphous poly(3‐hexylthiophene) on active‐layer structure and solar cells performance

A key challenge to the development of polymer‐based organic solar cells is the issue of long‐term stability, which is mainly caused by the unstable time‐dependent morphology of active layers. In this study, poly(3‐hexylthiophene) (P3HT)/[6,6]‐phenyl C60‐butyric acid methyl ester (PCBM) blend is used as a model system to demonstrate that the long‐term stability of power conversion efficiency can be significantly improved by the addition of a small amount of amorphous regiorandom P3HT into semicrystalline regioregular one. The optical properties measured by UV–vis absorption and photoluminescence reveal that regiorandom P3HT can intimately mix with PCBM and prevent the segregation of PCBM. In addition, X‐ray scattering techniques were adopted to evidence the retardation of phase separation between P3HT and PCBM when regiorandom P3HT is added, which is further confirmed by optical microscopy that shows a reduction of large PCBM crystals after annealing at high temperature in the presence of regiorandom P3HT. The improvement of the long‐term stability is attributed to the capability of amorphous P3HT to be thermodynamically miscible with PCBM, which allows the active layer to form a more stable structure that evolves slower and hence decelerates the device decay. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 975–985