一价铜改性ZSM-5催化剂及其催化碳烟氧化反应性能研究

采用固态离子交换法制备了系列一价铜改性的ZSM-5催化剂,结合多种表征手段,研究了一价铜改性对碳烟氧化反应催化活性的影响。结果表明,采用固态离子交换法可以制备出高负载量的一价铜改性Cu/ZSM-5分子筛催化剂,而不会破坏ZSM-5分子筛原有微孔结构;随催化剂中一价铜比例的增加,低温还原峰和高温还原峰均向低温段移动,且低温还原峰面积增加。改性催化剂对碳烟氧化反应的催化活性随改性元素比例变化先增加后降低;当铜改性比例超过11%后,铜物种的分散性及催化剂对碳烟氧化反应的催化活性均恶化。同时研究还发现,反应气氛中通入NO可以改善催化剂对碳烟氧化反应的催化效果。     

Pd/MWCNTs(多壁碳纳米管)催化剂的制备及其Heck反应催化活性

以浓硝酸处理后的多壁碳纳米管(MWCNTs)为载体,通过微波辅助法简单而快速地制备了高度分散、粒径均一的Pd/MWCNTs催化剂。利用XRD、HRTEM、XPS等手段对催化剂进行了表征。考察了Pd/MWCNTs催化剂对Heck反应的催化活性,并优化了反应温度、碱的种类和用量等反应条件。结果表明,Pd/MWCNTs在Heck反应中具有良好的催化活性。     

氧化铈气凝胶担载氧化铜催化剂的TPR研究

 采用程序升温还原研究了氧化铈气凝胶担载氧化铜催化剂的还原行为,并与其对一氧化碳氧化反应的催化活性进行了关联．发现此类催化剂中存在两种类型的氧化铜,即体相氧化铜和分散于载体表面的氧化铜,且后者中的部分氧化铜还原后易被氧化．随着此易被氧化的铜含量的增加,催化剂对一氧化碳氧化反应的催化活性升高,表明此种类型的铜为催化剂的活性组分．     

溶剂热法制备磷掺杂碳纳米管作为氧气还原和氧气析出反应双功能电催化剂的研究

对氧气还原(ORR)和氧气析出(OER)反应都具有催化活性的双功能催化剂在金属-空气电池中起着关键作用.本文通过溶剂热反应,一步原位合成了磷掺杂碳纳米管(P-CNT).旋转环盘电极测试表明磷掺杂能够明显提高碳纳米管的催化活性,P-CNT在碱性电解质中对ORR和OER都具有优异的催化活性.P-CNT对ORR的催化还原为近4电子反应,可与商业催化剂Pt/C(20 wt%)相比;而其对OER的催化活性则高于Pt/C(20 wt%).此外,P-CNT的长期稳定性优于Pt/C(20 wt%).P-CNT对ORR和OER的高催化活性和稳定性主要归因于磷对碳的掺杂以及磷与碳间强的化学键合.     

碳纳米管/杂多酸/聚吡咯复合催化剂的制备及催化烯烃环氧化性能

以磷钼酸(PMo)、吡咯(Py)和碳纳米管(CNTs)为原料,通过原位聚合方法制备了PPy-PMo@CNTs复合材料.采用傅里叶变换红外光谱(FTIR)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)等手段对材料进行了结构表征.结果表明,磷钼酸和聚吡咯被引入到碳纳米管载体上,且聚吡咯在碳纳米管表面形成了一层薄层.N2吸附-脱附测试结果表明,PPy-PMo@CNTs为介孔材料.将以乙腈为溶剂,过氧化氢为氧化剂的烯烃环氧化反应作为模型反应,考察了催化剂PPy-PMo@CNTs的催化活性.结果表明,在60℃,反应底物为1 mmol,催化剂投量为10 mg的条件下,该催化剂表现出较好的催化活性.中断和循环实验结果表明,催化剂具有较好的稳定性,在相同的反应条件下经过5次循环后,环辛烯的转化率依然保持在约65%.     

海藻酸铜负载CuTIPP催化羟化苯酚的研究

将四(对异丙基苯基)铜卟啉(CuTIPP)分散于海藻酸钠胶珠中,通过与铜离子水溶液反应制得海藻酸铜—CuTIPP胶珠。以双氧水为氧化剂,风干的胶珠为催化剂,对苯酚的催化羟化反应进行了探究。实验结果表明:负载CuTIPP的海藻酸铜催化剂催化活性要高于海藻酸铜催化剂,苯二酚的产率相对于海藻酸铜提高了9%,苯酚转化率达到了40.2%,苯二酚邻、对比接近4∶5。     

甲醇水蒸气重整制氢的高效碳纳米管改性Cu/ZnO/Al2O3催化剂

以碳纳米管为助剂,制备用于甲醇水蒸气重整制氢的新型高效Cu/ZnO/Al₂O₃催化剂,并与传统Cu/ZnO/Al₂O₃催化剂在相同条件下的催化性能进行了比较.结果表明,添加适量碳纳米管可显著提高催化剂的低温催化活性和选择性,在大幅度提高产氢速率的同时有效降低了重整产气中CO的含量.SEM和XRD分析证实适量碳纳米管的添加有效促进了Cu/ZnO/Al₂O₃催化剂结构特性的改善,有利于活性铜物种的分散,从而显著提高了催化剂的低温催化性能.     

合成甲醇的催化剂Rh-ZnO/MWNTs的研究

研究新型的由多壁碳纳米管(MWNTs)负载的， ZnO助催的铑基甲醇合成催化剂. 当铑含量达到4％(w)时，催化剂具有较高的比表面积(99.6 m2•g－1), 催化剂的反应活化能为68.8 kJ•mol－1.在563 K, 1 MPa下，催化剂的最高催化活性和甲醇选择性分别为411.4 mg/gcat.•h和96.7％. TEM、TPR和TPD等表征结果显示，碳纳米管能增加Rh在催化剂表面的分散度，提高催化剂的还原温度并能增加氢物种的吸附量，这些结果将有助于更好地了解催化剂中各组分间的协同作用和催化活性中心本质.     

吡咯氮配位单原子铜催化剂的电催化二氧化碳还原性能

采用温度控制的浸渍-热解法, 合成了以碳纳米管为载体的一系列铜单原子催化剂. 扩展X射线吸收精细结构(EXAFS)分析表明, 催化剂中的单原子铜位点分别由吡啶氮和吡咯氮配位. 电催化性能测试表明, 所制备催化剂可用于电催化二氧化碳生成一氧化碳, 由吡啶氮配位的铜单原子催化剂的反应选择性较差, 而由吡咯氮配位的铜单原子催化剂则具有更强的活性, CO法拉第效率在-0.70 V(vs. RHE)时可达到96.3%; 吡咯氮配位的铜单原子中心对于析氢反应具有更好的抑制效果.     

乙二胺功能化处理CNTs对NiB/CNTs催化剂性能的影响

用乙二胺功能化处理碳纳米管,增强其亲水性,有利于非晶态合金在碳纳米管负载.用化学还原法制备NiB/CNTs非晶态合金,以苯加氢探针为反应考察催化剂的活性,利用XRD、ICP、BET、TEM、TPR、TPD等方法对催化剂进行表征,结果表明乙二胺功能化处理,CNTs比表面积增大,镍的负载量增多,镍硼颗粒细化,从而提高了非晶态NiB/CNTs的催化活性,增强了其抗硫性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.