TiO2@CdS core–shell nanorods films: Fabrication and dramatically enhanced photoelectrochemical properties

In this paper, we prepared TiO₂@CdS core–shell nanorods films electrodes using a simple and low-cost chemical bath deposition method. The core–shell nanorods films electrodes were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and UV–vis spectrometry techniques. After applying these TiO₂@CdS core–shell nanorods electrodes in photovoltaic cells, we found that the photocurrent was dramatically enhanced, comparing with those of bare TiO₂ nanorods and CdS films electrodes. Moreover, TiO₂@CdS core–shell nanorods film electrode showed better cell performance than CdS nanoparticles deposited TiO₂ nanoparticles (P25) film electrode. A photocurrent of 1.31 mA/cm², a fill factor of 0.43, an open circuit photovoltage of 0.44 V, and a conversion efficiency of 0.8% were obtained under an illumination of 32 mW/cm², when the CdS nanoparticles deposited on TiO₂ nanorods film for about 20 min. The maximum quantum efficiency of 5.0% was obtained at an incident wavelength of 500 nm. We believe that TiO₂@CdS core–shell heterostructured nanorods are excellent candidates for studying some fundamental aspects on charge separation and transfer in the fields of photovoltaic cells and photocatalysis.     

Room temperature synthesis of CdS nanoparticle-decorated TiO2 nanotube arrays by electrodeposition with improved visible-light photoelectrochemical properties

Controllable CdS nanoparticles (NPs) decorated on TiO₂ nanotube arrays (NTAs) were prepared via electrodeposition in DMSO solution at room temperature, aiming to improve the photoelectrochemical properties of TiO₂ NTA electrode in visible-light region. By tuning the concentrations of sulfur and Cd^2 + as well as the deposition time, CdS NPs with different sizes can be controllably synthesized at room temperature. Excellent photocurrent response and incident photo to current conversion efficiency were achieved with smaller CdS NPs with optimal reactant concentrations and deposition time, which can be attributed to highly efficient charge separation and high dispersion of CdS NPs on both inner and outer surfaces of TiO₂ nanotubes.     

CdSe/TiO2 nanocrystalline solar cells

CdSe sensitized TiO₂ nanocrystalline solar cells were made with the participation of silicotungstic acid (STA) during the deposition of CdSe, the resulting Voc and Isc were 0.23 V cm^-2 and 10 mA cm^-2, respectively. The doping, time and microporous membrane effects were also discussed.     

The performance of coupled (CdS:CdSe) quantum dot-sensitized TiO2 nanofibrous solar cells

Highly porous networks and reduced grain boundaries with one-dimensional (1-D) nanofibrous morphology offer enhanced charge transport in solar cells applications. Quantum dot (QDs) decorated TiO₂ nanofibrous electrodes, unlike organic dye sensitizers, can yield multiple carrier generations due to the quantum confinement effect. This paper describes the first attempt to combine these two novel approaches, in which CdS (～18 nm) and CdSe (～8 nm) QDs are sensitized onto electrospun TiO₂ nanofibrous (diameter ～80–100 nm) electrodes. The photovoltaic performances of single (CdS and CdSe) and coupled (CdS/CdSe) QDs-sensitized TiO₂ fibrous electrodes are demonstrated in sandwich-type solar cells using polysulfide electrolyte. The observed difficulties in charge injection and lesser spectral coverage of single QDs-sensitizers are solved by coupling (CdS:CdSe) two QDs-sensitizers, resulting in a enhanced open-circuit voltage (0.64 V) with 2.69% efficiency. These results suggest the versatility of fibrous electrodes in QDs-sensitized solar cell applications.     

Spectral broadening in quantum dots-sensitized photoelectrochemical solar cells based on CdSe and Mg-doped CdSe nanocrystals

In order to absorb a broad spectrum in visible region, a co-sensitized TiO₂ electrode was prepared by CdSe and Mg-doped CdSe quantum dots (Q dots). The power conversion efficiency of the co-sensitized Q dots photoelectrochemical solar cells (PECs) showed 1.03% under air mass 1.5 condition (I = 100 mW/cm²), which is higher than that of individual Q dots-sensitized PECs. The incident-photon-to-current conversion efficiency of the co-sensitized PECs showed absorption peaks at 541 and 578 nm corresponding to the two Q dots and displayed a broad spectral response over the entire visible spectrum in the 500–600 nm wavelength domains.     

Effects of electron beam irradiation on the photoelectrochemical properties of TiO2 film for DSSCs

TiO₂ has been widely utilized for various industrial applications such as photochemical cells, photocatalysts, and electrochromic devices. The crystallinity and morphology of TiO₂ films play a significant role in determining the overall efficiency of dye-sensitized solar cells (DSSCs). In this study, the preparation of nanostructured TiO₂ films by electron beam irradiation and their characterization were investigated for the application of DSSCs. TiO₂ films were exposed to 20–100 kGy of electron beam irradiation using 1.14 MeV energy acceleration with a 7.46 mA beam current and 10 kGy/pass dose rates. These samples were characterized using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), and X-ray photoelectron spectroscopy (XPS) analysis. After irradiation, each TiO₂ film was tested as a DSSC. At low doses of electron beam irradiation (20 kGy), the energy conversion efficiency of the film was approximately 4.0% under illumination of simulated sunlight with AM 1.5 G (100 mW/cm²). We found that electron beam irradiation resulted in surface modification of the TiO₂ films, which could explain the observed increase in the conversion efficiency in irradiated versus non-irradiated films.     

Photocatalytic activity of nitrogen and copper doped TiO2 nanoparticles prepared by microwave-assisted sol-gel process

Cu and N-doped TiO₂ photocatalysts were synthesized from titanium (IV) isopropoxide via a microwave-assisted sol-gel method. The synthesized materials were characterized by X-ray diffraction, UV-vis diffuse reflectance, photoluminescence (PL) spectroscopy, SEM, TEM, FT-IR, Raman spectroscopy, photocurrent measurement technique, and nitrogen adsorption–desorption isotherms. Raman spectra and XRD showed an anatase phase structure. The SEM and TEM images revealed the formation of an almost spheroid mono disperse TiO₂ with particle sizes in the range of 9-17 nm. Analysis of N₂ isotherm measurements showed that all investigated TiO₂ samples have mesoporous structures with high surface areas. The optical absorption edge for the doped TiO₂ was significantly shifted to the visible light region. The photocurrent and photocatalytic activity of pure and doped TiO₂ were evaluated with the degradation of methyl orange (MO) and methylene blue (MB) solution under both UV and visible light illumination. The doped TiO₂ nanoparticles exhibit higher catalytic activity under each of visible light and UV irradiation in contrast to pure TiO₂. The photocatalytic activity and photocurrent ability of TiO₂ have been enhanced by doping of the titania in the following order: (Cu, N) - codoped TiO₂ > N-doped TiO₂ > Cu-doped TiO₂ > TiO₂. COD result for (Cu, N)-codoped TiO₂ reveals ∼92% mineralization of the MO dye on six h of visible light irradiation.     

Photocurrent generated on a carotenoid-sensitized TiO2 nanocrystalline mesoporous electrode

Photocurrent was observed upon monochromatic illumination of an ITO electrode coated with a TiO₂ nanocrystalline mesoporous membrane with carotenoid 8′-apo-β-caroten-8′-oic acid (ACOA) deposited as a sensitizer (illuminated area 0.25 cm²) and immersed in an aqueous 10 mM hydroquinone (H₂Q), 0.1 M NaH₂PO₄ solution (pH = 7.4) purged with argon, using a platinum flag counter electrode (area 3.3 cm²) and a SCE reference electrode. The carotenoid-sensitized short-circuit photocurrent reached 4.6 μA/cm² upon a 40 μW/cm² incident light beam at 426 nm, with an IPCE (%, incident monochromatic photon-to-photocurrent conversion efficiency) as high as 34%. The short-circuit photocurrent was stable during 1 h of continuous illumination with only a 10% decrease. An open-circuit voltage of 0.15 V was obtained (upon 426 nm, 40 μW/cm² illumination) which remained at a constant value for hours. The observed open-circuit voltage is close to the theoretical value (0.22 V) expected in such a system. The action spectrum resembled the absorption spectrum of ACOA bound on the TiO₂ membrane with a maximum near 426 nm. No decay of the ACOA on the TiO₂ surface was observed after 12 h, presumably because of rapid regeneration of ACOA from ACOA⁺ at the surface by electron transfer from H₂Q.     

Effect of water content of ethylene glycol as electrolyte for synthesis of ordered titania nanotubes

Anodization of Ti using fluoride containing polyhydric alcohols such as ethylene glycol or glycerol as electrolyte results in ordered arrays of TiO₂ nanotubes with a smooth surface and a very high aspect ratio. However, the reproducibility of the result is affected by many experimental parameters, notably the water content. In this investigation, anodizations of Ti foil in anhydrous ethylene glycol +0.2 wt% NH₄F solution (EG solution) with 0–1.0 wt% water additions were carried out at 20 V for 45 min in a dry-argon filled controlled-atmosphere glove box. It was observed that a minimum amount of 0.18 wt% of water addition was required to form a well ordered TiO₂ nanotubular arrays. When the anhydrous EG solution was reused for third time, ordered arrays of nanotubes started to form. When the water addition to the EG solution was more than 0.5 wt%, formation of ridges was observed on the nanotubes. XPS results showed presence of un-anodized Ti element in the anhydrous condition and presence of organic and (NH₄)₂TiF₆ type compounds in all the anodized samples in addition to the regular TiO₂ phase. The results underline the influence of water content and local pH condition to form the ordered nanotubular arrays.     

Visible LED light photoelectrochemical sensor for detection of L-Dopa based on oxygen reduction on TiO2 sensitized with iron phthalocyanine

The present work describes the development of a new strategy to photoelectrochemical detection of L-Dopa at low potential based on oxygen reduction on TiO₂ sensitized with iron phthalocyanine (FePc/TiO₂). The FePc/TiO₂ composite shows a photocurrent 10-fold higher than that of pure TiO₂ nanoparticles and it was 4-fold higher than that of FePc exploiting visible light. The band gaps of pure TiO₂ nanoparticles, FePc and FePc/TiO₂, calculated according to the Kubelka–Munk equation, were 3.22 eV, 3.11 eV and 2.82 eV, respectively. The FePc/TiO₂ composite showed a low charge transfer resistance in comparison to the photoelectrode modified with FePc or TiO₂. Under optimized conditions, the photoelectrochemical sensor shows a linear response range from 20 up to 190 μmol L^− 1 with a sensitivity of 31.8 μA L mmol^− 1 and limit of detection of 1.5 μmol L^− 1 for the detection of L-Dopa.     

Highly efficient CdSe quantum-dot-sensitized TiO2 photoelectrodes for solar cell applications

With 4.2 nm quantum-dots (QDs) as seeds on TiO₂ film, a highly efficient TiO₂ photoelectrode was prepared by a seed-growing process using chemical bath deposition technique, followed by a covering process with ZnS layer, and a post-sintering process at 400 °C. The assembled solar cells presented IPCE peak values of 73% and power conversion efficiency of 3.21% under AM 1.5 G irradiation.     

The Preparation of Dye Sensitized Solar Cell (DSSC) from TiO2 and Tamarillo Extract

Energy crisis is what being faced by every country today. Many efforts have been devoted to overcome the problems. One of several offered solutions is to develop solar cells (SCs) since solar energy is abundant and free to use. Especially in a tropical country like Indonesia, solar energy is available a whole year with quite high power 450 mWcm^-2. Several types of SCs, especially silicon-based, have been mass-produced and applied in our daily life. Silicon-based SC has high efficiency yet has high price. Dye Sensitized Solar Cell is an inexpensive type of SC. The natural ingredients could be utilized as dyes for DSSC. In this research, tamarillo extract was employed as the dye for TiO₂-based DSSC. TiO₂ powder was spin-coated on top of Fluorine- Doped Tin Oxide (FTO) conductive glass and calcined at 550 ̊C, 650 ̊C and 750 ̊C each for 60 and 120 min. Scanning ElectronMicroscope (SEM) and X-Ray Diffractometer (XRD) were used to characterize the morphology and structure of the material. Brunauer-Emmet-Teller (BET) analysis was utilized to measure the material active surface area. As the result, the sample calcined at 650 ̊C for 60 minutes showed the highest electrical performance of 542.5 mV and 0.356 mAcm^-2 which corresponded to an SC efficiency of 0.043%. This result was supported by the BET analysis showing the sample calcined at 650 ̊C for 60 min had the largest active surface area of 9.3 m²g^-1. A large active surface area enabled more dye and electrolyte to be stored inside the material so that photon adsorptions from solar energy became more effective and resulting in higher efficiency. Despite of the small efficiency, this work demonstrated the opportunities of tamarillo and TiO₂ to be applied as a DSSC.     

The improved photocatalytic properties of P-type NiO loaded porous TiO2 sheets prepared via freeze tape-casting

For the interest of the practical application, porous TiO₂ sheets were prepared by a novel freeze tape-casting method, in order to improve the photocatalytic activities of these TiO₂ sheets, p-type NiO was loaded by chemical solution deposition. The samples were characterized by a series of physical means, including XRD, SEM, EDS, XPS, ICP-OES, and UV-vis spectroscopy. The photocatalytic activities of the samples were evaluated by the degradation of methyl orange solution. The results showed that the photocatalytic activity of the TiO₂ sheet was greatly enhanced by the NiO loading, and the photocatalytic efficiency increased with increasing the NiO loading, the extraordinary performance for the NiO-loaded sample with 0.1 M precursor dipped was related to its unique morphology. The sample annealed at 600 °C showed the better photocatalytic activity than the sample annealed at 400 °C and 800 °C. The improvement of the photocatalytic activity was attributed to the formation of p–n junctures at the interface of the NiO/TiO₂, which facilitates the photoinduced electron/hole pairs' separation by the inner electric field, thus leading to the higher photocatalytic activities for the NiO-loaded TiO₂ sheets.     

Doping level effect on visible-light irradiation W-doped TiO2–anatase photocatalysts for Congo red photodegradation

A series of W-modified TiO₂ (W–TiO₂) photocatalysts were synthesized by a simple sol–gel method. The new photocatalysts were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–vis-diffuse reflectance spectroscopy (DRS), and Brunauer, Emmett and Teller (BET) surface area analyzer. The photoactivity of the W–TiO₂ photocatalysts was evaluated by the photocatalytic oxidation of Congo red (CR) dye. It was found that the average size of the prepared photocatalysts is 10 nm. Moreover, they have high surface areas (∼ 216 m² g⁻¹) and their light-absorption extends to the visible region compared to pure TiO₂. The effects of W-loading and of the calcination temperature of the prepared photocatalysts on their photocatalytic activity were also studied. The obtained results show that the W_0.5–TiO₂ photocatalyst calcined at 350 °C is much highly photoactive than non-doped or highly doped TiO₂. The enhanced photocatalytic activity of the weakly doped TiO₂ may be attributed to the increase in the charge separation efficiency and the presence of surface acidity on the W_0.5–TiO₂ photocatalyst.     

TiO2 nanotube arrays fabricated by anodization in different electrolytes for biosensing

Titania nanotube arrays were fabricated by anodic oxidation of titanium foil in different electrolytes. The morphology, crystallinity and composition of the as-prepared nanotube arrays were studied by XRD, SEM and EDX. Electrochemical impedance spectroscopy (EIS) was employed to investigate their electrical conductivity and capacitance. Titania nanotube arrays co-adsorbed with horseradish peroxidase (HRP) and thionine chloride (Th) were studied for their sensitivity to hydrogen peroxide by means of cyclic voltammetric and galvanostatic measurements. The experiments showed that TiO₂ nanotube arrays possessed appreciably different sensitivities to H₂O₂ due to their different conductivity. Further experiments revealed that TiO₂ nanotubes have noticeably different ability of adsorbing HRP and Th, and the best sensitivity was achieved when the density of HRP is the highest. The TiO₂ nanotube arrays fabricated in potassium fluoride solution demonstrated the best sensitivity on hydrogen peroxide in the range of 10⁻⁵–3 × 10⁻³ M at pH 6.7 and at a potential of −600 mV (vs. Ag/AgCl).     

Modification of photocatalytic TiO2 thin films by electron beam irradiation

Noble metal-modified TiO₂ films were prepared by electron beam deposition of Pt, Pd, Au and Ag on the surface of TiO₂ films with diameters ranging from <1 nm to 500 nm. The morphology of the films was characterized by X-ray diffractometry (XRD), field emission scanning electron microscope (FMSEM) and transmission electron microscope (TEM). The photocatalytic capability of the films were tested and compared by degradation of methyl orange (MO) in aqueous solutions under both UV and visible light illumination.     

Photoelectrochemical solar cell properties of heteropolytungstic acid-incorporated TiO2 nanodisc thin films

Thin film of heteropolytungstic acid (HPA)-incorporated TiO₂ nanodisc was fabricated, and its photovoltaic performances were observed as a function of irradiation wavelength from 400 nm to 750 nm. Its incident photon-to-current efficiency (IPCE) was determined to be 18.6% around 500 nm, with energy conversion efficiency of 6.9%, which were observed to be further enhanced to 23% and 9%, respectively, by adsorption of ruthenium or porphyrin dyes. Complementary electron transports from both HPA and dyes to TiO₂ nanodisc seems to avoid most of the backward electron or hole transfer reactions to enhance the photoelectrochemical efficiencies of dye-sensitized solar cells.     

Co-sensitization of vertically aligned TiO2 nanotubes with two different sizes of CdSe quantum dots for broad spectrum

In order to absorb a broad spectrum in the visible region, vertically aligned TiO₂ nanotubes (TONTs) were co-sensitized by two different sizes of CdSe quantum dots (Q dots). The power conversion efficiency of co-sensitized Q dots solar cells showed 1.20%. The co-sensitization of Q dots showed higher performance than the single size sensitization. The incident photon-to-current conversion efficiency of co-sensitized TONTs electrode showed two absorption peaks at 520 and 550 nm demonstrating the sensitization of Q dots with two different sizes. This efficiency enhanced charge harvesting efficiency over the entire visible spectrum, particularly the 500–600 nm wavelength domains.     

Enhanced electrochemical performance of carbon-coated TiO2 nanobarbed fibers as anode material for lithium-ion batteries

We report the electrochemical performance of carbon-coated TiO₂ nanobarbed fibers (TiO₂@C NBFs) as anode material for lithium-ion batteries. The TiO₂@C NBFs are composed of TiO₂ nanorods grown on TiO₂ nanofibers as a core, coated with a carbon shell. These nanostructures form a conductive network showing high capacity and C-rate performance due to fast lithium-ion diffusion and effective electron transfer. The TiO₂@C NBFs show a specific reversible capacity of approximately 170 mAh g^− 1 after 200 cycles at a 0.5 A g^− 1 current density, and exhibit a discharge rate capability of 4 A g^− 1 while retaining a capacity of about 70 mAh g^− 1. The uniformly coated amorphous carbon layer plays an important role to improve the electrical conductivity during the lithiation–delithiation process.     

Tio2@Sn core–shell nanotubes for fast and high density Li-ion storage material

TiO₂@Sn core–shell nanotube material prepared by thermal decomposition of SnCl₄ on TiO₂ nanotubes at 300 °C has been demonstrated superior Li-ion storage capability of 176 mA h/g even at high current rate of 4000 mA/g (charge and discharge of all TiO₂ within 5 min) in spite of using low carbon content (5 wt%). This value corresponds to volumetric energy densities of 317 mA h/cm³, and its value was 3.5-fold larger than that of the bare TiO₂ nanotubes.