Photovoltaic characteristics of dye-sensitized surface-modified nanocrystalline SnO2 solar cells

Zinc-modified nanocrystalline SnO₂ electrodes are prepared by chemical treatment of the commercial SnO₂ colloid with zinc acetate and their thickness effects on photovoltaic characteristics are investigated. Open-circuit voltage (V_oc) and fill factor increase with increasing zinc concentration, while short-circuit photocurrent (J_sc) decreases. The normalized incident photon-to-current conversion efficiency (IPCE) shows that increase of zinc concentration utilizes long wavelength light. Concerning the conversion efficiency, optimal concentration within the present experiment is found to be 10 mol.% Zn²⁺ with respect to Sn⁴⁺. As increasing thickness of the films based on 10 mol.% zinc-modified SnO₂ ranging from 0.76 to 8.12 μm, J_sc increases, reaches maximum and then decreases without change in V_oc. The highest conversion efficiency of about 3.4% is achieved under 1 sun of AM 1.5 irradiation for the ∼6.3 μm-thick 10 mol.% zinc-modified SnO₂ film with J_sc of 9.09 mA/cm², V_oc 600 mV and fill factor 62%.     

Photophysical and photochemical studies of thifensulfuron-methyl herbicide in aqueous solution

The photophysical and photochemical studies of a sulfonylurea herbicide, thifensulfuron-methyl (THM), have been investigated in a buffered aqueous solution. In the first part, the influence of pH on the spectroscopic properties was studied. This allowed the determination of the ground and excited state acidity constants, pK_a = 4 and 4.4, respectively, thus exhibiting the potential existence of a photoinduced protonation in the singlet state. In the second part, the photolysis kinetics was studied at different pH and varying oxygen concentrations, using an HPK 125 W lamp and followed up by the identification of photoproducts formed under continuous photo-irradiation. The kinetics results suggest that the photolysis process is faster in acidic (k = 3 × 10^?4 s^?1) than in basic medium (k = 9.8 × 10^?5 s^?1). The photolysis products were identified by high performance liquid chromatography HPLC-DAD, HPLC–MS and HPLC–MS–MS. In order to obtain a better understanding of the photodegradation mechanism, a laser flash photolysis study was performed. By comparing the quenching rate constant (k_q = 9.64 × 10⁸ mol^?1 l s^?1) obtained from triplet state quenching by molecular oxygen and from the Stern–Volmer relation (k_q = 0.41 × 10⁸ mol^?1 l s^?1), the role of the singlet state in the photodegradation process was demonstrated. The photoproducts originating from both singlet and triplet excited states have been identified and hypothetical photodegradation pathways of the thifensulfuron-methyl in aqueous solution are proposed.     

Facile synthesis of thick ordered mesoporous TiO2 film for dye-sensitized solar cell use

Crack-free thick ordered mesoporous TiO₂ films with excellent optical quality have been synthesized by combination of “Doctor Blade” technique and a two-step evaporation induced self-assembly (EISA) method. By employing the as-synthesized mesoporous film with the thickness of 7 μm as the photoanode in dye-sensitized solar cell (DSC), a solar conversion efficiency of 6.53% has been obtained at 30 mW cm⁻² light intensity.     

Evaluation of Schiff bases of 2,5-dimercapto-1,3,4-thiadiazole as photostabilizer for poly(methyl methacrylate)

The photostabilization of poly(methyl methacrylate) (PMMA) films by Schiff bases of 2,5-dimercapto-1,3,4-thiadiazole compounds was investigated. The PMMA films containing concentration of complexes 0.5% by weight were produced by the casting method from chloroform solvent. The photostabilization activities of these compounds were determined by monitoring the hydroxyl index with irradiation time. The changes in viscosity average molecular weight of PMMA with irradiation time were also tracked (using benzene as a solvent). The quantum yield of the chain scission (Φ_cs) of these complexes in PMMA films was evaluated and found to range between 4.19 × 10^?5 and 8.75 × 10^?5. Results obtained showed that the rate of photostabilization of PMMA in the presence of the additive followed the trend:[1] > [2] > [3] > [4] > [5].According to the experimental results obtained, several mechanisms were suggested depending on the structure of the additive. Among them, UV absorption, peroxide decomposer, and radical scavenger for photostabilizer mechanisms were suggested.     

On the structural and magnetoelectrical characterization of epitaxial SrRuO3 thin films grown on (001) SrTiO3 substrates

High-quality epitaxial thin films of the ferromagnetic metallic oxide SrRuO₃ (SRO) were fabricated by dc-sputtering at high oxygen pressure and their structural and magnetoelectrical properties were carefully studied. The films featured a Curie temperature T_C ～ 160 K and a magnetic moment of ～0.7 μ_B per Ru ion. The temperature dependent magnetization could be well described by the scaling relation M(T) ∝ (T_C ? T)^β with a critical exponent β = 0.53 over the entire ferromagnetic temperature range. A negative magnetoresistance, MR, on the order of a few percent was found up to room temperature. MR showed a maximum of ～4% right at T_C where a kink structure of the resistivity, ρ, at zero field was flattened out on magnetic field application. This ρ contribution could be related to scattering due to orientational disorder of the Ru magnetic moments which become aligned by an external magnetic field. In addition, an equally strong MR effect, related to localization phenomena, could be observed at lower temperature. Particularly, the second MR peak at ～35 K might be related to a Fermi-liquid to non-Fermi-liquid crossover. A scaling behavior dρ/dT ∝ |T ? T_C|^α was observed only above T_C. Here, values for the exponent α ≈ ?0.4 and α ≈ ?1.4 were obtained in zero field and in a field of 9 T, respectively. The commonly observed ρ minimum, appearing at low temperatures (～3 K in the present case), is correlated with the structural disorder of the SRO films and is believed to have its origin in quantum corrections to the conductivity (QCC).     

Polyaniline nanotubes for impedimetric triglyceride detection

Polyaniline nanotubes (PANI-NT) based film electrophoretically deposited onto indium–tin–oxide (ITO) coated glass plate has been utilized for covalent immobilization of lipase (LIP), via glutaraldehyde (Glu), for triglyceride detection using impedimetric technique. It is shown that fatty acid molecules produced during triglyceride hydrolysis result in change in charge transfer resistance (R_CT) of PANI-NT film with varying triglyceride concentration. LIP/Glu/PANI-NT/ITO bioelectrode has linearity as 25–300 mg dL^?1, sensitivity as 2.59 × 10^?3 KΩ^?1 mg^?1 dL, response time as 20 s and regression coefficient as 0.99. A low value of apparent Michaelis–Menten constant (～0.62 mM) indicates high enzyme affinity to tributyrin. The LIP/Glu/PANI-NT/ITO bioelectrode has been utilized to estimate triglyceride in serum samples.     

Evolution of microstructure and crack pattern in NiO thin films under 200 MeV Au ion irradiation

NiO thin films grown on Si (100) substrate by electron beam evaporation method and sintered at 700 °C were irradiated with 200 MeV Au¹⁵⁺ ions. The fcc structure of the sintered films was retained up to the highest fluence (1×10¹³ ions cm^?2) of irradiation. However the microstructure of the pristine film underwent a considerable modification with increasing ion fluence. 200 MeV Au ion irradiation led to compressive stress generation in NiO medium. The diameter of the stressed region created by 200 MeV Au ions along the ion path was estimated from the variation of stress with ion fluence and found to be ～11.6 nm. The film surface started cracking when irradiated at and above the fluence of 3×10¹² ions cm^?2. Ratio of the fractal dimension of the cracked surface obtained at 200 MeV and 120 MeV (Mallick et al., 2010a) Au ions was compared with the ratio of the radii of ion tracks calculated based on Coulomb explosion and thermal spike models. This comparison indicated applicability of thermal spike model for crack formation.     

Investigation of O7+ swift heavy ion irradiation on molybdenum doped indium oxide thin films

Molybdenum (0.5 at%) doped indium oxide thin films deposited by spray pyrolysis technique were irradiated by 100 MeV O⁷⁺ ions with different fluences of 5×10¹¹, 1×10¹² and 1×10¹³ ions/cm². Intensity of (222) peak of the pristine film was decreased with increase in the ion fluence. Films irradiated with the maximum ion fluence of 1×10¹³ ions/cm² showed a fraction of amorphous nature. The surface microstructures on the surface of the film showed that increase in ion fluence decreases the grain size. Mobility of the pristine molybdenum doped indium oxide films was decreased from ～122 to 48 cm²/V s with increasing ion fluence. Among the irradiated films the film irradiated with the ion fluence of 5×10¹¹ ions/cm² showed relatively low resistivity of 6.7×10^?4 Ω cm with the mobility of 75 cm²/V s. The average transmittance of the as-deposited IMO film is decreased from 89% to 81% due to irradiation with the fluence of 5×10¹¹ ions/cm².     

Fast formation of thick and transparent titania nanotubular films from sputtered Ti

Ti films sputtered on transparent fluorine-doped tin oxide glass substrates were anodized in fluoride-containing organic electrolyte in the presence of H₂O. In this work, anodic TiO₂ nanotubes (ATNs) as long as 9.2 ± 0.3 μm were obtained with high growth rate of 0.64 ± 0.3 μm min^?1. We demonstrated the optimum anodization conditions for ATN growth on foreign substrates, were within the range of 0.3–0.5% (wt) NH₄F, with 3–5% (vol) H₂O at 60 V. XPS and ICP-MS were utilized to elucidate the increase of thickness and volume expansion obtained from the sputtered Ti film to their ATN forms. The ATN films exhibited excellent uniformity and adhesion to the substrates.     

A study on solution deposited CuSCN thin films: Structural,electrochemical, optical properties

A cost-effective successive ionic layer adsorption and reaction (SILAR) method was used to deposit copper (I) thiocyanate (CuSCN) thin films on glass and steel substrates for this study. The deposited thin films were characterized for their structural, morphological, optical and electrochemical properties using X-ray diffraction (XRD), scanning electron microscopy (SEM), UV–visible spectroscopy and VersaSTAT potentiostat. A direct band gap of 3.88 eV and 3.6 eV with film thickness of 0.7 μm and 0.9 μm was obtained at 20 and 30 deposition cycles respectively. The band gap, microstrain, dislocation density and crystal size were observed to be thickness dependent. The specific capacitance of the CuSCN thin film electrode at 20 mV/s was 760 F g⁻¹ for deposition 20 cycles and 729 F g⁻¹ for deposition 30 cycles.     

Fe-doped SnO2 transparent semi-conducting thin films deposited by spray pyrolysis technique: Thermoelectric and p-type conductivity properties

In this paper, we report structural, electrical, optical, and especially thermoelectrical characterization of iron (Fe) doped tin oxide films, which have been deposited by spray pyrolysis technique. The doping level has changed from 0 to 10 wt% in solution ([Fe]/[Sn] = 0–40 at% in solution). The thermoelectric response versus temperature difference has exhibited a nonlinear behavior, and the Seebeck coefficient has been calculated from its slope in temperature range of 300–500 K. The Hall effect and thermoelectric measurements have shown p-type conductivity in SnO₂:Fe films with [Fe]/[Sn] ≥ 7.8 at%. In doping levels lower than 7.8 at%, SnO₂:Fe films have been n-type with a negative thermoelectric coefficient. The Seebeck coefficient for SnO₂:Fe films with 7.8 at% doping level has been obtained to be as high as +1850 μV/K. The analysis of as-deposited samples with thicknesses ～350 nm by X-ray diffraction (XRD) and scanning electron microscopy (SEM) has shown polycrystalline structure with clear characteristic peak of SnO₂ cassiterite phase in all films. The optical transparency (T%) of SnO₂:Fe films in visible spectra decreases from 90% to 75% and electrical resistivity (ρ) increases from 1.2 × 10^?2 to 3 × 10³ Ω cm for Fe-doping in the range 0–40 at%.     

Fabrication of a large area cathode-supported thin electrolyte film for solid oxide fuel cells via tape casting and co-sintering techniques

A large area cathode-supported electrolyte film, comprising porous (La_0.8Sr_0.2)_0.95MnO₃ (LSM95) cathode substrate, LSM95/Zr_0.89Sc_0.1Ce_0.01O_2?x (SSZ) cathode active layer, and SSZ electrolyte, has been successfully fabricated by tape casting and co-sintering techniques. The interface reaction between cathode and electrolyte was inhibited by using A-site deficient LSM. A dense enough SSZ thin film with a thickness of ～26 μm was obtained at 1250 °C. By using Pt as anode, the obtained single cell reached the maximum power density of 0.54 W cm^?2 at 800 °C in O₂/humidified H₂, with open circuit voltage (OCV) value of 1.08 V.     

High contrast ratio and fast switching polymeric electrochromic films based on water-dispersible polyaniline-poly(4-styrenesulfonate) nanoparticles

We prepared polyaniline-poly(4-styrenesulfonate) nanoparticles (PANI/PSS-NPs) by chemical oxidation polymerization in aqueous solution. We investigated the potential of the PANI/PSS-NPs to be used as an anode electrode for electrochromic devices and the effect of Li⁺ insertion (or deinsertion) kinetics and diffusion of Li⁺. A uniform electrochromic layer of PANI/PSS-NPs with a size of ca. 28 nm could be obtained by a solution process, specifically spin coating. The PANI/PSS-NPs film has a high Li⁺ diffusion coefficient (～7.7 × 10^?9 cm² s^?1) and low charge transfer resistance (～99 Ω), which result in its having a fast electrochromic response time (coloring time <1.7 s, bleaching time <2.4 s), and high coloration efficiency (>108 cm² C^?1).     

The determination of trace lead in drinking water by flow injection spectrophotometry

Lead is the non-essential trace element in the human body, and it has been confirmed that drinking water is one of the sources of lead in human body. In the research, based on the sensitive colour reaction of lead with I^?–EV⁺–PVA, a simple, sensitive, accurate and portable method for the determination of trace lead in drinking waters was proposed. Chemicals and physicals had been optimized in detail. The apparent molar absorption coefficient was up to 7.4 × 10⁵ mol L^?1 cm^?1. The developed method provided a linearity range over 5–80 μg L^?1. The regression deviation was between 0.71% and 2.33%. The 3σ detection limit was 0.9 μg L^?1. Close to the quantitation limit for the analyte the relative standard deviation was 1.10% (n = 10) at 40 μg L^?1. The method developed here for analysis of lead yielded results that were comparable with those of the GFAAS.     

High temperature superconductor micro SQUID magnetometer for molecular-based magnets

We have developed a high temperature superconductor (HTS) micro SQUID magnetometer for molecular-based magnets. By employing the dipole approximation, we verified the flux value of 40Φ₀ from the saturation magnetic moment of the ferrimagnetic microcrystal of [Mn₂(H₂O)₂(CH₃COO)][W(CN)₈] · 2H₂O (15 × 15 × 13 μm). Considering the relative arrangement of the sample and the SQUID loop, including the influence of the film and grease, the calculated the flux values were Φ = 71Φ₀ and 31Φ₀ at distances of 20 and 30 μm between the sample bottom face and the SQUID plane, respectively. Thus, the experimentally obtained flux value is reasonable.     

Electrodeposition of hyaluronic acid and hyaluronic acid–bovine serum albumin films from aqueous solutions

Hyaluronic acid (HYH) films were prepared from aqueous sodium hyaluronate (HYNa) solutions by anodic electrodeposition. The film thickness was varied in the range of 0–20 μm by the variation of the deposition time and HYNa concentration. The deposition rate was low at HYNa concentration below 1 g L⁻¹ and increased significantly in the range of 3–5 g L⁻¹. The addition of bovine serum albumin (BSA) to the HYNa solutions resulted in increased deposition yield, which was attributed to the formation of composite HYH–BSA films. The thickness of the HYH–BSA films deposited by anodic electrodeposition was varied in the range of 0–80 μm. The HYH and composite HYH–BSA films were studied by scanning electron microscopy, thermogravimetric analysis, differential thermal analysis, Fourier transform infrared spectroscopy and circular dichroism spectroscopy. The deposition mechanism and kinetics of deposition are discussed.     

Photolysis of glyoxal in air

The photolysis of glyoxal in synthetic air was investigated in a quartz cell at 298 K using three types of UV sources (TL/12 lamps (275–380 nm), TL/03 lamps (390–470 nm) and mercury lamps (254 nm)) and products were identified and quantitatively analyzed using long-path FTIR spectroscopy. For all light sources, the observed products were CO, HCHO and HCOOH. Absolute quantum yields were determined using Cl₂ and Br₂ as actinometers. Photolysis in the first absorption band of glyoxal, using TL/12 lamps, provided an overall quantum yield of Φ_T = 0.97 ± 0.05, independent of total pressure ranging from 100 to 700 Torr air. The absolute quantum yields obtained with the TL/03 lamps, covering the second absorption band of glyoxal, showed dependency on total pressure, ranging from Φ_T = 0.12 at 100 Torr to Φ_T = 0.042 at 700 Torr, which can be expressed as a Stern–Volmer-type equation 1/Φ_T = (6.80 + 251.8) × 10⁻⁴ × P (Torr).By combining the product yields with literature data, we deduced the detailed picture of glyoxal photolysis, including the dependency of the quantum yield of each particular channel: CHOCHO + hν → 2HCO (Φ₁); CHOCHO + hν → H₂ + 2CO (Φ₂); CHOCHO + hν → H₂CO + CO (Φ₃) on the applied wavelength. The product quantum yields indicate that dissociation into two HCO radicals is the most important pathway under atmospheric conditions. The mean photolysis rate was measured under solar radiation in the EUPHORE outdoor chamber to be J_obs = 1.04 ± 0.10 × 10⁻⁴ s⁻¹, corresponding to a mean effective quantum yield ϕ_eff = 0.035 ± 0.007. Although glyoxal has a very low effective quantum yield, photolysis remains an important removal path in the atmosphere.     

NADH oxidation on screen-printed electrode modified with a new phenothiazine diazonium salt

NADH oxidation catalysts are extremely important in the field of electrochemical biosensors and enzymatic biofuel cells. Based on the growing diazonium chemistry, we synthesized the diazonium salt of the well-known NADH mediator toluidine blue O. The electrochemical reduction of the diazonium moiety by cyclic voltammetry onto a screen-printed electrode leads to an electrocatalyst suitable for the oxidation of NADH. The amperometric response for its oxidation shows a maximal current of 1.2 μA ([NADH] = 100 μM). Based on electrochemical measurements, the surface coverage is found to be 3.78 × 10^? 11 mol cm^? 2 and the heterogeneous standard rate constant k_h is 1.21 ± 0.16 s^? 1. The sensitive layer for the oxidation of NADH is improved by electrografting the diazonium salt with a potentiostatic method. Both the surface coverage and the heterogeneous standard rate constant k_h are improved and found to be 6.08 ± 0.63 × 10^? 11 mol cm^? 2 and ~ 5.02 s^? 1, respectively. The amperometric response is also improved by an 8 fold factor, reaching 9.87 μA ([NADH] = 120 μM). These remarkably high values for screen-printed electrodes are comparable to glassy carbon electrodes making this method suitable for low-cost bioelectronical devices.     

Chemical bath deposition of CdS quantum dots on vertically aligned ZnO nanorods for quantum dots-sensitized solar cells

Formation of CdS quantum dots (Q dots) on the vertically aligned ZnO nanorods electrode was carried out by chemical bath deposition. The diameter and thickness of ZnO nanorods are ～100–150 nm and ～1.6 μm, respectively, and CdS Q dots on ZnO nanorods have a diameter of smaller than 15 nm. In application of the Q dots-sensitized solar cells, composite film exhibited a power conversion efficiency of 0.54% under air mass 1.5 condition (80 mW/cm²), and incident-photon-to-current conversion efficiency showed 18.6%.     

Phage Langmuir monolayers and Langmuir–Blodgett films

Stable, insoluble Langmuir monolayer films composed of Staphylococcus aureus-specific lytic bacteriophage were formed at an air–water interface and characterized. The phage monolayer was very strong, withstanding a surface pressure of ～40 mN/m at 20 °C. The surface pressure–area (Π–A) isotherm possessed a shoulder at ～7 × 10⁴ nm²/phage particle, attributed to a change in phage orientation at the air–water interface from horizontal to vertical capsid-down/tail-up orientation as surface pressure was increased. The Π–A-dependence was accurately described using the Volmer equation of state, assuming horizontal orientation to an air–water interface at low surface pressures with an excluded area per phage particle of 4.6 × 10⁴ nm². At high pressures phage particles followed the space-filling densely packed disks model with a specific area of 8.5 × 10³ nm²/phage particle. Lytic phage monolayers were transferred onto gold-coated silica substrates from the air–water interface at a constant surface pressure of 18 mN/m by Langmuir–Blodgett method, then dried and analyzed by scanning electron microscopy (SEM) and ellipsometry. Phage specific adsorption (Γ) in Langmuir–Blodgett (LB) films measured by SEM was consistent with that calculated independently from Π–A isotherms at the transfer surface pressure of 18 mN/m (Γ = 23 phage particles/μm²). The 50 nm-thickness of phage monolayer measured by ellipsometer agreed well with the horizontal phage average size estimated by SEM. Surface properties of phage Langmuir monolayer compare well with other monolayers formed from nano- and micro-particles at the air–water interface and similar to that of classic amphiphiles 1,2-diphytanoyl-sn-glycero-3-phosphocholine (phospholipid) and stearic acid.