Raman fiber laser improvement by using Yb3+-doped fiber

We report here the efficiency improvement in a fiber Raman laser by splicing to it short pieces of 10000-ppm Yb³⁺-doped fibers. The amplified spontaneous emission produced by the doped fiber started the stimulated Raman scattering earlier than the spontaneous scattering in the 350-m silica-fiber cavity. In the best case, when splicing to the cavity 127 cm of doped fiber, the pump threshold decreased from 2.9 down to 1.27 W, representing a 56% improvement. This power was close to the theoretical minimum of 1.25 W for very long fibers. The second stokes signal (1175 nm) was only present when the doped fibers were inserted. At 4-W pump, the non-doped cavity delivered 2 W of first stokes signal (1117 nm) that represent a 50% efficiency compared to ～3 W delivered (～75%) when a 34-cm doped fiber was inserted. This improvement is intended to reduce the cost of fiber Raman lasers because less powerful sources or shorter fibers are necessary to produce more stokes components.     

Self-seeded multiwavelength Brillouin-erbium fiber laser

We propose and demonstrate a self-seeded multiwavelength Brillouin-erbium fiber laser with an internally self-excited Brillouin pump, which is achieved by incorporation of a length of single-mode fiber together with a Sagnac loop mirror into a fiber ring cavity. In this simple scheme the Brillouin pump is self-excited in the fiber ring cavity and then used to seed the Brillouin multiwavelength comb in the single-mode fiber. Stable generation of more than 120 Brillouin Stokes wavelengths with relatively uniform amplitudes is demonstrated with this scheme. It is also shown that such a self-seeded Brillouin laser has good stability and repeatability.     

Diode-pumped 1018-nm ytterbium-doped double-clad fiber laser

We report a 1 018-nm ytterbium-doped double-clad fiber laser pumped by 970-nm diode. A pair of fiber Bragg gratings with reflectivities of 99.9% and 9% at a center wavelength of 1 018.9 nm are employed as cavity mirrors. The ytterbium-doped double-clad fiber is a 2.6-m-long Liekki fiber. Laser output power of 7.5 W at 1 018 nm is obtained under the pump power of 59.2 W. The overall slope efficiency of the fiber laser is about 16%. This low slope efficiency is mainly due to the incomplete absorption of the pump power.     

Analysis of the Polarization Influence on the Erbium-Doped Fiber Laser Transient Behavior

Abstract

We studied the erbium-doped fiber laser transient behavior dependence on the pump polarization state or on the cavity polarization eigenvalues. Several series of measurements are shown in which the changes in the transient laser response can be appreciated as the pump polarization state, or the cavity polarization eigenvalues are modified by means of polarization controllers. Results are fitted to a model considering polarization hole burning. It is shown that including this effect is fundamental for a correct erbium-doped fiber laser transient model. On the other hand, the validity of the model's fitting parameters under pump or cavity polarization changes is analyzed.     

Widely tunable linear-cavity multiwavelength fiber laser with distributed Brillouin scattering

We demonstrate a multiple wavelength Brillouin/erbium fiber laser in a linear cavity configuration.The laser cavity is made up of a fiber loop mirror on one end of the resonator and a virtual mirror generated from the distributed stimulated Brillouin scattering effect on the other end.Due to the weak reflectivity provided by the virtual mirror,self-lasing cavity modes are completely suppressed from the laser cavity.At Brillouin pump and 1480-nm pump powers of 2 and 130 mW,respectively,11 channels of the demonstrated laser with an average total power of 7.13 dBm can freely be tuned over a span of 37-nm wavelength from 1530 to 1567 nm.     

Continuous wave tunable fiber optical parametric oscillator with double-pass pump configuration

We demonstrate a continuous wave tunable fiber optical parametric oscillator in a Fabry–Perot cavity consisting of a 500-m highly nonlinear fiber. In this work, the pump propagates in both directions together with the signal, thus making full use of its parametric gain. The resultant laser peak power is uneven across the wavelength range of interest due to wavelength-dependent phase modulation by the single-mode fiber sections in the cavity. This can be solved by filtering the idler spectral component from the oscillating cavity.     

强泵浦下掺Yb3+双包层光纤激光器输出特性数值分析和实验研究

对强泵浦下线形腔掺Yb3+双包层光纤激光器输出特性进行了理论和实验研究。通过数值模拟,分析了泵浦光及激光在光纤中的分布、输出功率与泵浦功率的关系、光纤长度及腔镜反射率对激光输出功率的影响。在实验中,利用D型掺Yb3+双包层光纤获得了输出功率10 6W的光纤激光输出,斜率效率达86%。测量了在不同输出耦合条件下的输出功率、阈值泵浦功率和斜率效率,理论分析与实验结果基本一致,为进一步提高光纤激光器功率提供了理论和实验依据。     

Ti:S激光器外腔选频产生820 nm带激光研究

首次报道了用Ti：S激光器及Tm-Ho共掺石英光纤等构成复合腔，通过外腔选频产生波长为820nm波段高性能单模激光的实验研究，复合腔Ti：S激光器的光-光转换效率达15．7％，斜率效率可达17．3％。研究了输出激光功率、输出光谱随泵浦功率、激活光纤长度的变化关系，并对相应结果进行了分析。     

Emission Dependence on Length in a 1.48-mum Pumped Erbium-Doped Laser with an All-Fiber Configuration

We report a study on the main features of a 1.48-mum pumped erbium-doped fiber laser, such as threshold pump power, output power, and slope efficiency. In particular we have focused on its dependence on active fiber length. We employed an all-fiber laser configuration, which included mirrors directly coated onto the polished fiber endfaces. Launched pump power and laser output power were introduced and extracted, respectively, from the laser cavity by means of couplers. Our measure ments show the existence of an optimum erbium-doped fiber length, where threshold power reaches minimum and output power maximum.     

Low-power-pumped high-efficiency frequency doubling at 397.5 nm in a ring cavity

We report low pump power high-efficiency frequency doubling of a fundamental laser beam at 795 nm, corresponding to the rubidium D1 line, to generate UV light at 397.5 nm using a periodically poled KTi OPO4（PPKTP） crystal in a ring cavity. We obtain maximum stable output power of 49 m W for mode-matching pump power of 110 m W, corresponding to 45% raw efficiency（56% net efficiency when considering the output coupling mirror’s 80% transmission）. This is the highest efficiency obtained at this wavelength in PPKTP with such low pump power. We obtain 80% beam coupling efficiency to single-mode fiber, demonstrating high beam quality.     

非线性吸收诱导掺镱光纤激光器中的光学双稳

研究了在掺镱光纤激光器中观察到的光学双稳态现象.激光信号光和驻留泵浦光的双稳特性来源于激光器在小信号和增益饱和两种情况下,掺镱光纤对信号的非线性吸收导致的激光器内腔非线性损耗.同时分析了把泵浦光中的光学双稳行为通过分叉的腔结构扩展到切换式双波长光纤激光器的可行性.     

Optimization of erbium-doped fiber MOPA laser

An erbium-doped fiber laser (EDFL) constructed in a master oscillator and power amplifier (MOPA) configuration is analyzed. The pump powers for the fiber cavity laser and the booster amplifier stages are managed properly to achieve maximal pump conversion efficiency. Our design achieves a pump conversion efficiency of 91.4%, corresponding to a quantum efficiency of 96.6%, for a 1565.8 nm MOPA laser pumped by a total power of 300 mW at 1480 nm. The optimized MOPA laser shows a 25% enhancement in the pump conversion efficiency, compared to a non-MOPA fiber laser. A side lobe suppression ratio of 48 dB for the optimized MOPA laser is observed.     

Optimization of linear cavity design of Yb-doped double-clad fiber laser

The output characteristics of a linear cavity Yb-doped double-clad fiber (DCF) laser, including the effects of fiber length, fiber loss, and output mirror reflectivity on laser output power and threshold pump power have been studied theoretically and experimentally. In this paper, the linear cavity of double-clad fiber laser (DCFL) was composed of a pair of fiber Bragg gratings, while the facet of fiber was anti-reflection (AR) coated at 1070nm to erase the Fresnel reflection. Analysis showed that the laser output increases as the reflectivity of the fiber Bragg grating used as the output mirror decreases. At last, under the pump power of 14.4 W, single-mode laser output at 1070 nm was up to 10.8 W, with slope efficiency of 75 %.     

Local-cooled watt-level Nd-doped phosphate single-mode fiber laser

Efficient and stable continuous-wave (CW) laser operation at 1053 nm in a Nd-doped phosphate single-mode fiber (Nd:PSMF) has been demonstrated experimentally. The fiber laser consisted of a 21 cm Nd:PSMF placed in a F-P cavity formed by high reflector butt-coupled to coupling end of the fiber and Fresnel reflection of the other end facet. An output power of 1.42 W and a slope efficiency of 34.1% (18.4%) with respect to absorbed pump power (incident pump power) were obtained with 808 nm diode pumping. An increment as much as 9.7 and 15.0% in slope efficiency of the input coupling efficiency and the output power, respectively, were obtained by using a local-cooling design provided by watered sealing the coupling point. The repeatable results indicate that the design, featuring fluid sealing the coupling point of the fiber laser, which was capable of offering an effective alleviation of thermal effects and an elevation of the quality of the laser cavity, could be expected to be a convenient and effective scheme to improve the performance characteristics of the non-silica fiber lasers and the high power fiber lasers, generally in free-space coupling configuration.     

Efficient second-harmonic generation of continuous-wave Yb fiber lasers coupled with an external resonant cavity

Efficient second-harmonic generation of continuous-wave Yb fiber lasers is reported. A simple bow-tie external resonant cavity incorporating a type I LBO nonlinear optical crystal was employed for second harmonic frequency conversion of a multi-longitudinal-mode Yb fiber laser. It is shown that strong coupling was formed between the Yb fiber laser and the external cavity and, as a result, the laser produced 9.1 W of green output at 535 nm for 43?W of absorbed diode pump power at 975 nm corresponding to an optical conversion efficiency of 21?% with respect to absorbed diode pump power. The prospects for further improvement are discussed.     

Characterization of an Intra-Cavity Pumped P2O5-Doped Silica Raman Fiber Laser

We examine the characteristics of a P₂O₅-doped Raman fiber laser pumped by a double-clad ytterbium-doped fiber laser in an intra-cavity configuration. The double-clad fiber laser consists of two high reflection fiber Bragg gratings at 1092 nm, with an active length of 17 m, where the output grating is located at the end of the 400m P₂O₅-doped fiber. The Raman cavity is formed by a 1278-nm-high reflection fiber Bragg grating spliced to the double-clad fiber, and a 50% output coupler. The maximum conversion efficiency at 1278 nm with respect to the input pump power at 915 nm was 26.9%.     

利用全光纤结构Michelson腔实现两路高功率双包层光纤激光器相干合成

Michelson腔技术是实现激光相干合成的有效方案. 利用Michelson腔技术, 实现了全光纤结构下的两路光纤激光器的相干合成, 获得了功率为11.75 W, 效率为95.76%的相干输出. 实验研究了相干合成效率与激光腔长差的关系以及抽运对称性对相干合成效率的影响. 实验表明相干合成效率极易受激光腔长差的影响, 不同腔长差下相干合成效率差异可达18%以上, 且存在最佳腔长差; 抽运对称性对相干合成效率的影响在2%以内.     

增益调制高重频脉冲光纤激光器实验研究

采用脉冲泵浦方案,研制出了基于增益调制技术的全光纤结构高重频脉冲激光器。采用电路直接调制的激光二极管作为泵浦源,双包层光纤作为增益介质,构造了光纤光栅选模的线形腔结构。实验中通过调整泵浦光脉冲宽度和光纤激光器谐振腔长度,得到了稳定的高重频脉冲。在100kHz重复频率下,采用21W的峰值泵浦功率和2.5μs的泵浦脉冲宽度,获得了1.06μm波长,脉冲宽度247ns的稳定脉冲激光输出。脉冲峰值功率一致性好,平均功率长期功率稳定性为2%。观察并分析了由于纵模拍频在脉冲包络上产生的次脉冲特性。通过一级放大实现89.6 W输出。     

Tunable Ytterbium-Doped Fiber Laser Based on a Mechanically Induced Long Period Holey Fiber Grating

We describe a tunable double-clad Yb-doped fiber laser based on a long period fiber grating mechanically induced in a section of single mode holey fiber inserted into the laser cavity. The mechanically induced long period holey fiber grating acts as a wavelength-selective fiber filter whose central wavelength, linewidth, and strength can be tuned by changing the period, the length of the grating, and the applied pressure. The fiber laser gives a ∼12.6 nm tuning range, from ∼1079:4–1092nm, with slope efficiencies of 18.7–26.3% at this wavelength range, with respect to the launched pump power.     

基于光纤光栅的高功率光纤激光器

分析了光纤光栅的选频原理以及光纤光栅基高功率光纤激光器的阈值特性和输出特性.采用紫外写入的光纤光栅做谐振腔,研制了全光纤结构的高功率光纤激光器,泵浦阈值为186 mW, 最大输出功率1.78 W,斜率效率59%,实验结果与理论分析基本吻合.