双层A3钢靶对平头杆弹的抗侵彻性能研究

 钢板被广泛用于构建防护结构,大量文献报道了单层金属靶的防护性能,而对双层金属靶,特别是大间隙双层金属靶,报道的却很少。在轻气炮上进行了平头杆弹体正撞击由两层5 mm厚A3钢板组成的接触式和具有200 mm间隙的间隙式双层靶的实验研究,得到了两种结构的初始-剩余速度曲线。实验表明：（1）两种形式双层靶均发生了充塞剪切;（2）接触式双层靶的弹道极限是5 mm单层A3靶的1.92倍;（3） 间隙式双层靶的抗侵彻性能具有较大的分散性,通过高速摄像和对回收靶板的分析表明,该分散性产生的原因是,弹体贯穿第一层靶后存在两种典型弹道状态;（4）间隙式双层靶存在两个弹道极限;（5）接触式双层靶的弹道极限接近或者大于间隙式双层靶的弹道极限。使用ABAQUS/EXPLICIT有限元软件进行了相应的数值模拟,得到了与实验一致的现象和结果。     

锥头弹丸撞击下FRP层合板的侵彻与穿透的理论研究

 研究了锥头弹丸撞击下FRP层合板的侵彻和穿透性能,在局部化破坏模式假定的基础上改进了Wen提出的能量简化分析模型。改进模型仍假设弹体在侵彻过程中表面所受靶体的平均压力由靶体材料弹塑性变形所引起的静态阻力和速度效应引起的动阻力两部分组成,认为侵彻过程中靶体对弹体的阻力不再是一个常数,而是侵彻速度的函数。并由此推导出了锥头弹丸在侵彻和贯穿过程中的侵彻深度、残余速度和弹道极限速度的公式。理论预测与实验结果符合得很好。     

锥头弹丸撞击下固支金属厚靶的侵彻与穿透的理论研究(英文)

研究了在不同速度的刚性锥头弹丸撞击下固支金属厚靶的侵彻和穿透性能。假定靶板的变形是局部化的,且冲击能量仅通过侵彻过程吸收,同时假定弹体在侵彻过程中表面所受靶体的平均压力是由基于空穴膨胀理论的靶体材料弹塑性变形所引起的静态阻力以及速度效应引起的动阻力两部分组成,认为侵彻过程中靶体对弹体的静阻力要进行自由表面效应修正,而且动阻力是瞬时侵彻速度的函数。获得了锥头弹丸在侵彻和贯穿过程中的弹道极限速度和残余速度的公式。将理论预测与实验结果进行比较,发现两者符合得很好。     

Detached shock waves around cylinders flying at mach number ranging from 1 to 2

Using a ballistic range with a small single-stage powder gun, characteristics of detached shock waves around cylindrical projectiles were investigated. The detaches shock waves were analyzed quantitatively by visualization method. The projectiles were made of steel, with a diameter of 5.56 mm and with a mass of 1.77 g. The projectiles were ejected into the test section of the ballistic range at supersonic speeds. Direction-indicating color schlieren method (DInCS) was used to visualize the flow field. The stand-off distance of the detached shock waves and the shape were obtained as the function of Mach number. The functions were compared with the results obtained by wind tunnel experiments. Analyzed images provided the quantitative information on shock shapes. The results were as follows: (1) the stand-off distances of the detached shock waves have been shown as exponential functions of Mach number; (2) the shapes of the shock waves have been found as quadratic functions of Mach number. The differences in the functions between this paper and a wind tunnel test were shown.     

高速碰撞过程中应变硬化材料靶动态响应研究

 给出了适用于可压缩、弹塑性、按幂次律应变硬化材料的动态柱形腔膨胀模型和侵彻模型，并编制了相应的计算程序。腔膨胀模型给出靶中应力分布情况，侵彻模型根据腔膨胀模型的有关结果来预估具有锥形头部的刚性弹丸侵彻半无限厚靶的最终侵彻深度以及贯穿薄靶时的弹丸剩余速度和弹道极限速度。给出了钨合金弹丸正碰5083-H131铝靶和钢弹丸正碰6061-T651铝靶的一些计算结果，计算结果与实验结果及二维拉氏弹塑性LTZ-2D程序的数值模拟结果符合得很好。     

内爆驱动式超高速发射技术的初步研究

为获得10 km/s左右的超高速发射能力,以内爆发射器为研究对象,利用AUTODYN 2D软件对口径为8 mm的内爆发射器进行有限元仿真分析,获得了典型状态下的弹丸发射速度。研制了口径为8 mm的内爆发射器,并在压缩管中填充5 MPa氦气进行实验,分别获得了0.55 g铝合金弹丸7.95 km/s和0.37 g镁合金弹丸10.28 km/s的发射速度,与有限元仿真计算结果的速度偏差分别为15.3%和3.7%。结果表明,设计的内爆发射器具备10 km/s发射能力,满足空间碎片撞击和防护研究的超高速发射需求。     

本构迭代算法在LS-DYNA中的嵌入

结合粘塑性本构理论,采用对商业软件LS-DYNA进行二次开发的方法将含损伤型Johnson-Cook本构模型嵌入商业有限元软件中,给出本构迭代算法和计算流程.并以平头和锥头两种弹形的高强度钢穿甲弹贯穿12 mm厚的Weldox靶板的实验为基础,进行数值模拟,实验结果和计算结果符合较好,表明给出的本构算法、含损伤型本构及损伤演化方程是合理可靠的.     

Investigation of the aerodynamic properties and flow field around hypervelocity objects in a ballistic test range

The equipment of a ballistic test range for research on hypersonic motion and flow around typical models of explosion-propelled projectiles. A method for obtaining instantaneous interferograms of the flow around an object and a procedure for calculating the radial density distributions from measurements made on them are briefly set forth. The values of the aerodynamic drag at zero angle of attack are obtained for three models in trajectory experiments, and a comparative assessment of their stability is made. The principles for performing numerical aerodynamic calculations of hypervelocity flow around objects typically having a compound shape are formulated. Zh. Tekh. Fiz. 69, 6–11 (December 1999)     

The response of polymethyl methacrylate (PMMA) subjected to large strains,high strain rates,high pressures,a range in temperatures,and variations in the intermediate principal stress

This article presents the response of polymethyl methacrylate (PMMA) subjected to large strains, high strain rates, high pressures, a range in temperatures, and variations in the intermediate principal stress. Laboratory data from the literature, and new test data provided here, are used in the evaluation. The new data include uniaxial stress compression tests (at various strain rates and temperatures) and uniaxial stress tension tests (at low strain rates and ambient temperatures). The compression tests include experiments at ?ε= 13,000 s^?1, significantly extending the range of known strain rate data. The observed behavior of PMMA includes the following: it is brittle in compression at high rates, and brittle in tension at all rates; strength is dependent on the pressure, strain, strain rate, temperature, and the intermediate principal stress; the shear modulus increases as the pressure increases; and it is highly compressible. Also presented are novel, high velocity impact tests (using high-speed imaging) that provide insight into the initiation and evolution of damage. Lastly, computational constitutive models for pressure, strength, and failure are presented that provide responses that are in good agreement with the laboratory data. The models are used to compute several ballistic impact events for which experimental data are available.     

Effects of laser intensity and ambient conditions on the laser-induced plume

Laser ablation presents a promising technique for material processing. The quality of products is strongly influenced by the properties of the laser-induced plume. In compressible flow, the ambient conditions can be transmitted upstream. Therefore, the laser ablation process is strongly affected by the ambient conditions. In this paper, the effects of laser intensity, back pressure and temperature on the laser-induced plume were studied using a numerical model, which calculates the density, pressure and temperature of the laser-induced plume at different laser intensity and ambient conditions. The results are in agreement with experimental results available in the literature and can be used for the optimization of the pulsed laser deposition process.     

Factors influencing the ballistic impact resistance of elastomer-coated metal substrates

An experimental study was carried out of various factors affecting the ballistic penetration resistance of elastomer/steel bilayers. For blunt penetrators, the contribution of the coating to performance is optimized using the hardest substrates, front surface placement of the elastomer, and (when normalizing by added weight) thin, ca. 2–3?mm, coatings. These results, none of which are predicted by existing models, evince the marked coupling of coating and substrate in the impact response of the bilayer. We also show that nanoparticle fillers have a modest effect on ballistic performance of polyurea coatings, changing the penetration velocity by a few percent or less. This contrasts with the linear dynamic mechanical behavior, which shows much more significant increases in energy absorption due to nano-reinforcement.     

平头弹丸正撞击下延性金属靶板的破坏模式

 对延性金属靶板在刚性平头弹丸正撞击下的破坏模式进行了研究。一般而言,延性金属靶板的破坏模式可以分为两种：带有总体变形的局部简单剪切破坏和局部化的绝热剪切冲塞破坏。首先基于Bai-Johnson热塑性本构关系建立了一个局部化的绝热剪切冲塞模型,然后结合描述带有总体变形的局部简单剪切破坏的Wen-Jones模型,找出了两种模型之间转化的临界条件。理论预测与文献中的实验结果吻合得很好。     

卵形钢弹对铝合金靶板侵彻问题的数值模拟

 基于球形空穴膨胀理论（SCE）,采用ABAQUS有限元商业软件并结合其子程序的二次开发功能对钢弹侵彻金属靶进行3D有限元数值模拟。根据空穴膨胀理论,靶体对侵彻弹体的影响可以用一个作用在弹体表面的力函数代替,这样在进行数值模拟时就无须划分靶体网格,也避免了复杂的接触问题,从而使模拟大大简化。模拟所用卵形弹为VAR 4340钢弹,靶体为6061-T6511铝合金。模拟过程中考虑到弹体的可变形性和入射时的微小偏航角等实际情况,并且考虑到了弹身在运动过程中和靶体的接触分离效应。所得模拟结果与文献中的实验结果进行了比较,发现模拟结果与实验结果吻合得很好,并得到了一些有意义的推论。     

Microcanonical relation between continuous and discrete spin models

A relation between a class of stationary points of the energy landscape of continuous spin models on a lattice and the configurations of an Ising model defined on the same lattice suggests an approximate expression for the microcanonical density of states. Based on this approximation we conjecture that if a O(n) model with ferromagnetic interactions on a lattice has a phase transition, its critical energy density is equal to that of the n=1 case, i.e., an Ising system with the same interactions. The conjecture holds true in the case of long-range interactions. For nearest-neighbor interactions, numerical results are consistent with the conjecture for n=2 and n=3 in three dimensions. For n=2 in two dimensions (XY model) the conjecture yields a prediction for the critical energy of the Bere?inskij-Kosterlitz-Thouless transition, which would be equal to that of the two-dimensional Ising model. We discuss available numerical data in this respect.     

High pressure laminar burning velocity measurements and modelling of methane and n-butane

A constant volume vessel has been used in conjunction with a numerical multi-zone model to calculate laminar burning velocities of methane and n-butane in the ranges φ = 0.8–1.4, T _u = 320–470 K, p _u = 1–15 bar from the pressure record. This multi-zone model has been compared with the analytical model of Luijten and de Goey. For methane, the experimental data have been compared with modelling data generated using the MIXFLA program of Warnatz. The MIXFLA data have further been used to examine the form of the correlation fitted to the experimental data, confirming the form used by Clarke. For methane, good agreement was found between the current experimental data and the literature at high pressures. For n-butane, poor agreement was found with the one data set available. However, the data from this reference did not compare well with other authors for methane.     

On the sensitivity analysis of porous material models

Porous materials are used in many vibroacoustic applications. Different available models describe their behaviors according to materials' intrinsic characteristics. For instance, in the case of porous material with rigid frame, and according to the Champoux–Allard model, five parameters are employed. In this paper, an investigation about this model sensitivity to parameters according to frequency is conducted. Sobol and FAST algorithms are used for sensitivity analysis. A strong parametric frequency dependent hierarchy is shown. Sensitivity investigations confirm that resistivity is the most influent parameter when acoustic absorption and surface impedance of porous materials with rigid frame are considered. The analysis is first performed on a wide category of porous materials, and then restricted to a polyurethane foam analysis in order to illustrate the impact of the reduction of the design space. In a second part, a sensitivity analysis is performed using the Biot–Allard model with nine parameters including mechanical effects of the frame and conclusions are drawn through numerical simulations.     

Numerical studies of charged particles in a magnetic field: Mars application

An approach to model the Martian magnetization can be done using classical source models. Classical models, such as uniformly magnetized spheres and cylinders, allow for the introduction of additional constraints related to the available information of the magnetic field and its sources. The use of a suitable conservative numerical scheme in Cartesian coordinates was carried out for numerical studies. In this work the motion of different charged particles under the influence of different magnetized sources have been analyzed by using the proposed numerical scheme. For that purpose, electron, proton and alpha particles were used. In addition, the impact of the gravitational effect on the particles motion was also studied.     

Time domain simulation in photonics: A comparison of nonlinear dispersive polarisation models

The paper investigates and compares a range of different models currently used for modelling nonlinear optical phenomena. The models are implemented in the numerical time domain Transmission Line Modelling (TLM) method and include a Kerr model and different formulations of the Duffing model. The models are used to simulate an all-optical limiter for a CW input and results compared with ones available in the literature. This enables a comparison to be made between the different models, from which it is concluded that the Duffing model has some advantages, when modelling materials and phenomena involving more than one frequency, arising from its ability to describe dispersive effects. These conclusions are further supported by the simulation results obtained for a pulse input.