Process influences on the structure,piezoelectric, and gas‐barrier properties of PVDF‐TrFE copolymer

The influence of annealing between the Curie transition and the melting point of solvent cast polyvinylidene fluoride trifluoroethylene copolymer films on the crystalline structure, mechanical and electrical properties, and oxygen permeability is investigated. Annealing leads to remarkable changes in the structure and properties of the copolymer, within the first four hours of treatment, and with kinetics depending on the temperature. The crystallinity increases by 19% (relative), resulting in a 10 K increase in the Curie transition, a 4 K increase of the melting temperature and a 2 K decrease in the glass transition temperature. A crystalline phase transition from the paraelectric α‐phase to the ferroelectric β‐phase is also evidenced using in‐situ X‐ray diffraction. The elastic modulus is found to increase by more than three‐fold at room temperature and the loss peak at the glass transition is considerably reduced. The piezoelectric coefficient is found to increase by 40% and the dielectric properties are significantly changed. The most remarkable influence is the ten‐fold reduction of the oxygen permeability, with a drastic reduction of the activation energy for oxygen transport. The improvement in oxygen barrier properties of the annealed copolymer is attributed to the restricted mobility of oxygen molecules in the semicrystalline polymer with nanometer sized crystallites. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 496–506     

Investigation of clay modifier effects on the structure and rheology of supercritical carbon dioxide‐processed polymer nanocomposites

Superior property enhancements in polymer–clay nanocomposites can be achieved if one can significantly enhance the nanoclay dispersion and polymer–clay interactions. Recent studies have shown that nanoclays can be dispersed in polymers using supercritical carbon dioxide (scCO₂). However, there is need for a better understanding of how changing the clay modifier affects the clay dispersability by scCO₂ and the resultant nanocomposite rheology. To address this, the polystyrene (PS)/clay nanocomposites with “weak” interaction (Cloisite 93A clay) and “strong” interaction (Cloisite 15A clay) have been prepared using the supercritical CO₂ method in the presence of a co‐solvent. Transmission electron microscopy images and small‐angle X‐ray diffraction illustrate that composites using 15A and 93A clays show similar magnitude of reduction in the average tactoid size, and dispersion upon processing with scCO₂. When PS and the clays are coprocessed in scCO₂, the “dispersion” of clays appears to be independent of modifier or polymer–clay interaction. However, the low‐frequency storage modulus in the scCO₂‐processed 15A nanocomposites is two orders of magnitude higher than that of 93A nanocomposites. It is postulated that below percolation (solution blended composites), the strength of polymer–clay interaction is not a significant contributor to rheological enhancement. In the scCO₂‐processed nanocomposites the enhanced dispersion passes the percolation threshold and the interactions dictate the reinforcement potential of the clay–polymer–clay network. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 823–831, 2010     

Morphology and properties of polypropylene/ethylene–octene copolymer/clay nanocomposites with double compatibilizers

The influence of nanoclay on the morphology and properties of the polypropylene (PP)/ethylene–octene block copolymer (EOC) blend with double compatibilizers of maleated PP (PP‐g‐MA) and maleated EOC (EOC‐g‐MA) was investigated and compared with the nanocomposites containing either PP‐g‐MA or EOC‐g‐MA as a compatibilizer. X‐ray diffraction, transmission electron microscopy, and scanning electron microscopy were utilized for morphological characterization in conjunction with dynamic mechanical thermal analysis, mechanical testing, and rheological evaluation of these nanocomposites. The results suggested that in the nanocomposite including both compatibilizers of PP‐g‐MA and EOC‐g‐MA, clay was dispersed as a mixed structure of intercalation and exfoliation in both phases of the polymer blend. Comparing the mechanical properties of the studied nanocomposite with nanocomposites of PP/EOC/PP‐g‐MA/clay and PP/EOC/EOC‐g‐MA/clay also indicated that the nanocomposite containing mixed compatibilizers displayed higher tensile modulus, tensile strength, and complex viscosity because of the better dispersion of clay in both phases. The results also confirmed the increased structural stability and reduced dispersed phase size of PP/EOC/PP‐g‐MA/EOC‐g‐MA blend in the presence of clay that proposed the compatibilization role of clay in this nanocomposite. Copyright © 2014 John Wiley & Sons, Ltd.     

Effects of electron irradiation on poly(vinylidene fluoride–trifluoroethylene) copolymers studied by solid‐state nuclear magnetic resonance spectroscopy

The effects of electron irradiation on the molecular chemical structure, conformation, mobility, and phase transition of vinylidene fluoride (VDF) and trifluoroethylene (TrFE) copolymer have been investigated with variable‐temperature, solid‐state ¹⁹F nuclear magnetic resonance (NMR). It has been found that electron irradiation converts all‐trans conformations of both VDF‐rich and TrFE‐containing segments into dynamically mixed trans–gauche conformations accompanied by a simultaneous ferroelectric‐to‐paraelectric (or amorphous) transition. The variable‐temperature ¹⁹F magic‐angle‐spinning spectra results show that the paraelectric phase melts at much lower temperatures in irradiated films than in an unirradiated sample. Moreover, ¹⁹F NMR relaxation data (spin–lattice relaxation times in both the laboratory and rotating frames) reveal that electron irradiation enhances the molecular motion in paraelectric regions, whereas the molecular motion in a high‐temperature amorphous melt (>100 °C) is more constrained in irradiated films. Besides these physical changes, electron irradiation also induces the formation of several CF₃ groups. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1714–1724, 2006     

Dielectric relaxation study in electron‐irradiated ferroelectric poly(vinylidene fluoride‐trifluoroethylene) (80/20 mol%) copolymer

The relaxor ferroelectric (RFE) behavior in high‐energy electron‐irradiated poly(vinylidene fluoride‐trifluoroethylene) [P(VDF‐TrFE)] 80/20 mol % copolymer system is characterized over a broad frequency and temperature range. The dielectric properties remarkably vary with the irradiated dose in terms of the change from normal ferroelectric (FE) to RFE phase. During the RFE–paraelectric (PE) transition, the dielectric constants, as a function of temperature, can be described by the Vogel–Fulcher (V–F) relation. It has been found that the relationship between the real and imaginary part of dielectric constant in irradiated copolymer can be well fitted with modified Cole–Cole equation and Debye relaxation equation, exhibiting similar features as inorganic RFEs. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2972–2980, 2005     

Barrier property of clay/Acrylonitrile‐butadiene copolymer nanocomposite

The resistance to air permeation was investigated for ­an intercalated clay/acrylonitrile‐butadiene copolymer ­nanocomposite. The nanocomposite is prepared by melt mixing the organo‐treated montmorillonite into a rubber matrix, together with peroxide curative, and crosslinked by conventional compression molding for typical rubbers. In the case of intercalated nanocomposite, the air permeability decreases considerably with increasing clay content, and the decreasing trend agrees reasonably with the Neilson's tortuous model. No considerable improvement is found when the pure montmorillonite is added. Copyright © 2002 John Wiley & Sons, Ltd.     

Surface characterization and barrier properties of plasma‐modified polyethersulfone/layered silicate nanocomposites

This study describes the preparation of polyethersulfone (PES)/layered silicate nanocomposites (PLSNs) by mixing PES polymer chain into organically‐modified layered silicate in 1‐methyl‐2‐pyrrolidinone (NMP) solution. Both X‐ray diffraction data and transmission electron microscopy images of PLSNs indicate that the silicate layers were almost exfoliated and randomly distributed into the PES matrix. The mechanical and barrier properties of PLSNs show remarkable enhancement in the storage modulus and water/oxygen permeability when compared with that of neat PES matrix. Surfaces modification of PES and PLSN films with various treated times, system pressures, and radio frequency (RF) powers were performed using a mixture of oxygen (O₂) and nitrogen (N₂) plasmas. The topographical and physical properties of plasma‐modified PES and PLSN surfaces were investigated using scanning probe microscopy (SPM), contact‐angle measurements, and X‐ray photoelectron spectroscopy (XPS). These results indicate that the surface roughness of PLSNs with the same condition of plasma modification is lower than that of neat PES matrix and is probably due to the increase of stiffness with the presence of inorganic layered silicates in PES matrix. The surface properties of the PES and PLSNs are also changed from hydrophobic to hydrophilic. The XPS spectra suggest that the exposure of the PES and PLSNs to the plasmas led to the combination of etching reactions of polymer surface initiated by plasma and the following addition reactions of new oxygen‐ and nitrogen‐containing functional groups onto polymer surfaces to change their surface properties. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3185–3194, 2006     

DFT study of ferroelectric properties of the copolymers: Poly(vinylideneflouride‐trifluoroethylene) and poly(vinylidene fluoride‐chlorotrifluoroethylene)

A theoretical study of poly(vinylidene flouride‐trifluoroethylene) and poly(vinylidene fluoride‐chlorotrifluoroethylene, is presented. By density functional theory calculations, some of the properties of these materials have been obtained. Among such properties, the dipolar moment and the energies associated to the structural changes. The B3LYP functional and 6311+G(d,p) bases set were used with Gaussian program. Calculations associated to different conformations were carried out to get insight about the involved phase changes. The energetic, charges, and dipole moment were calculated. The conformations, namely, I = T_p, II = TG_a, and III = TG_p, where T means trans and G means gauche, for the two polymers aforementioned were compared with the poly(vinilydene fluoride) studies previously obtained. © 2010 Wiley Periodicals, Inc. Int J Quantum Chem 110:2411–2417, 2010     

Preparation and properties of isobutylene–isoprene rubber–clay nanocomposites

Isobutylene isoprene rubber (IIR)‐clay nanocomposites have been prepared successfully by melt intercalation with maleic anhydride‐grafted IIR (Ma‐g‐IIR) and organophilic clay. In IIR‐clay nanocomposites, the silicate layers of the clay were exfoliated and dispersed into the monolayer. The nanocomposites exhibited greater gas barrier properties compared with those of Ma‐g‐IIR. When 15 phr clay was added, gas barrier properties were 2.5 times greater than those of Ma‐g‐IIR. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1182–1188, 2006     

Origin of Piezoelectricity in an Electrospun Poly(vinylidene fluoride‐trifluoroethylene) Nanofiber Web‐Based Nanogenerator and Nano‐Pressure Sensor

A single stage electrospinning process can give rise to preferentially oriented induced dipoles in poly(vinylidene fluoride‐trifluoroethylene) [P(VDF‐TrFE)] nanofibers. The piezoelectricity of as‐electrospun P(VDF‐TrFE) nanofiber webs opens up new possibilities for their use as a flexible nanogenerators and nano‐pressure sensors. In this work, the origin of the piezoelectricity has been spotlighted by randomization of the induced dipoles at the Curie temperature and analyzed by polarized FT‐IR spectroscopic techniques as well as by detecting the piezoelectric signal from a nano‐pressure sensor.

     

Surface characterization and properties of plasma‐modified cyclic olefin copolymer/layered silicate nanocomposites

In this study, cyclic olefin copolymer (COC)/layered silicate nanocomposites (CLSNs) were prepared by the intercalation of COC polymer into organically‐modified layered silicate through the solution mixing process. Both X‐ray diffraction data and transmission electron microscopy images of CLSNs indicate most of the swellable silicate layers were disorderedly intercalated into the COC matrix. The effect of layered silicate on the mechanical and barrier properties of the fabricated nanocomposites shows significant improvements in the storage modulus and water permeability when compared with that of neat COC matrix. Surfaces of COC and CLSN films were modified by a mixture of oxygen (O₂) and nitrogen (N₂) plasmas with various treated times, system pressures, and radio frequency (RF) powers. The surfaces of plasma‐modified COC and CLSN were investigated using scanning probe microscopy and contact‐angle measurements. The exposure of the COC and CLSN film to the plasmas led to the combination of etching reactions of polymer surface initiated by plasma and the following addition reactions of new functional groups onto polymer surfaces to change the topology of COC film surfaces. The surface roughness was closely related to how high and how long the RF power was input into the system. The plasmas also led to changes in the surface properties of the CLSN surfaces from hydrophobic to hydrophilic; and the contact angle of water on the surface decreases. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2745–2753, 2005     

Morphology and gas barrier properties of polyethylene‐based nanocomposites

Nanocomposites were processed by melt blending two reference matrices, a metallocene polyethylene and a low density maleic anhydride‐grafted polyethylene with an organo‐modified montmorillonite. It was shown that the introduction of a maleated polyethylene compatibilizer was required to improve the clay nanoplatelet dispersion in the metallocene polyethylene‐based nanocomposites. Increasing the montmorillonite content led to a significant increase of the barrier properties. Interfacial agents such as oxidized paraffins were shown to be more effective to reduce the gas permeability than maleated polyethylene and the dependence of the gas transport properties was discussed not only as a function of the clay dispersion but also as a function of the clay/compatibilizer and compatibilizer/matrix interactions. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 431–440, 2006     

Characteristic length of dynamic glass transition based on polymer/clay intercalated nanocomposites

The glass transition is an old physical problem. It has been accepted that there is a cooperatively rearranging region related to dynamic heterogeneity when temperature approaches the glass transition. However, there is no consensus with the characteristic length and the size of cooperatively rearranging region. This paper first employs the clay gallery in polymer/clay intercalated nanocomposites as a confined two-dimensional (2D) space to assess the characteristic length of dynamic glass transition. The five kinds of clays with different d-spacings were used to investigate the confinement effect. Theoretical calculation based on Donth's formula suggests that the characteristic lengths of polyol and polyol-based polyurethane are ∼3.20 and ∼1.45 nm, respectively. The experimental results agree with theoretical prediction using Donth's formula. The characteristic length varies with polymer types.     

Effect of Ionic Liquid Anion Type in the Performance of Solid Polymer Electrolytes Based on Poly(Vinylidene fluoride‐trifluoroethylene)

The effect of different anions within the ionic liquid in the characteristics of solid polymer electrolytes (SPEs) based on P(VDF‐TrFE) has been investigated. 1‐ethyl‐3‐methylimidazolium acetate, [C₂mim][OAc], 1‐ethyl‐3‐methylimidazolium triflate, [C₂mim][(CF₃SO₃)], 1‐ethyl‐3‐methylimidazolium lactate, [C₂mim][Lactate], 1‐ethyl‐3‐methylimidazolium thiocyanate, [C₂mim][SNC] and 1‐ethyl‐3‐methylimidazolium hydrogen sulfate [C₂mim][HSO₄] have been used in SPE prepared by solvent casting. The polymer phase, thermal and electrochemical properties of the SPE have been determined. The thermal and electrical properties of the SPEs strongly depend on the selected IL, as determined by their different interactions with the polymer matrix. The room temperature ionic conductivity increases in the following way for the different anions: [SNC]>[CF₃SO₃)]>[HSO₄]>[Lactate]>[OAc], which is mainly dependent on the viscosity of the ionic liquid.     

Surface modification of clay and its effect on the intercalation behavior of the polymer/clay nanocomposites

Melt intercalation of the methylsilylated organoclays with polar polymers such as SAN was examined to verify the adhesive role of guest polymeric chains between hydrophilic clay layers, so-called “glue effect” on intercalation behavior. Once methylsilylated organoclay was melt-blended with SAN, it was found that the mixture presented significant retardation of increase of interlayer spacing, d₀₀₁ with heating time, and a noticeable decrease of d₀₀₁ after the methylsilylation of organoclay, implying that the diffusion of SAN was highly suppressed by the decrease of polar interaction force caused by conversion of OH to methylsiloxyl groups. However, when applying shear force for the methylsilylated organoclay/SAN nanocomposites during melt intercalation, a noticeable increase of d₀₀₁ was observed, expressing that intercalation of clay by SAN occurred much more effectively because of the reduction of gluing force between host clay and guest polymers, which was well supported by dramatic improvements of mechanical properties after methylsilylation of organoclays. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2367–2372, 2004     

Modification of the structure and properties of poly(vinylidene fluoride–trifluoroethylene) 56/44 mol % copolymer by a proton‐irradiation treatment

The effects of high‐energy proton irradiation on the structure and properties of 56/44 mol % poly(vinylidene fluoride–trifluoroethylene) copolymer were studied with differential scanning calorimetry (DSC), X‐ray diffraction (XRD), relative permittivity, and polarization hysteresis measurements. Copolymer films prepared by hot compression molding were irradiated with a broad range of proton dosages (10–107 Mrad) at room temperature. The DSC results showed that the ferroelectric transition was strongly affected by the proton dosages. The XRD data indicated the reduction of polar ordering in the copolymer by the proton‐irradiation treatment. From the relative permittivity and polarization behavior, the copolymer film was found to be converted from a normal ferroelectric material to a relaxor ferroelectric material as the proton dosage was increased to 50 Mrad. The electrostrictive coefficient of the 56/44 mol % copolymer was enhanced after irradiation, and the optimized proton dosage for attaining the highest electrostrictive strain response was determined. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2334–2339, 2005     

Structure–property relationships of polymer blend/clay nanocomposites: Compatibilized and noncompatibilized polystyrene/propylene/clay

Polymer blends represent an important class of materials in engineering applications. The incorporation of clay nanofiller may provide new opportunities for this type of materials to enhance their applications. This article reports on the effects of clay on the structure and properties of compatibilized and noncompatibilized polymer blends and presents a detailed process for quantitative analysis of the elastic moduli of polymer blend/clay nanocomposites, based on immiscible polystyrene/polypropylene (PS/PP) blends with or without maleated PP as the compatibilizer. The results show that in the noncompatibilized PS/PP/clay nanocomposite clay locates solely in the PS phase, whereas in the compatibilized nanocomposite clay disperses in both phases. The addition of clay to both polymer blends reduces the domain size significantly, modifies the crystallinity and improves the stiffness. The Mori–Tanaka and Christensen's models offer a reasonably good prediction of the elastic moduli of both types of nanocomposites. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Montmorillonite‐based nanocomposites of polybenzoxazole: Synthesis and characterization (I)

Poly(amic acid) was synthesized by means of low‐temperature‐solution polymerization of 3,3′‐dihydroxybenzidine and pyromellitic dianhydride in N,N‐dimethylacetamide. The precursor polymer was heat‐treated at different temperatures to create a polybenzoxazole (PBO) through a polyimide (PI). PI containing the hydroxyl group was rearranged by decarboxylation with heat treatment, resulting in a fully aromatic PBO. Hexadecylamine was used as an organophilic alkylamine in organo‐clay. We have tried to clarify the intercalation of heterocyclic polymer chains to hexadecylamine–montmorillonite (C₁₆‐MMT) and improve tensile properties. It was found that the addition of only a small amount of organo‐clay was enough to improve the mechanical properties of PBO. Maximum enhancement in the ultimate tensile strength for PBO hybrids was observed for the blends containing 4% C₁₆‐MMT. The initial modulus monotonically increased with further increases in the C₁₆‐MMT content. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 471–476, 2001     

Melt blending of ethylene‐vinyl alcohol copolymer/clay nanocomposites: Effect of the clay type and processing conditions

Ethylene‐vinyl alcohol copolymer (EVOH)/clay nanocomposites were prepared via dynamic melt blending. The effect of the processing parameters on blends containing two clay types in different amounts was examined. The blends were characterized with a Brabender plastograph and capillary rheometer, differential scanning calorimetry, dynamic mechanical thermal analysis (DMTA), X‐ray diffraction (XRD), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). XRD showed advanced EVOH intercalation within the galleries, whereas TEM images indicated exfoliation, thereby complementing the XRD data. A dilution process with EVOH and clay treatment in an ultrasonic bath before melt blending did not add to the intercalation level. Different trends were observed for the EVOHs containing two different clay treatments, one claimed to be treated for EVOH and the other for amine‐cured epoxy. They reflected the differences in the amounts of the strongly interacting polymer for the two nanocomposites. Thermal analysis showed that the melting temperature, crystallization temperature, and heat of fusion of the EVOH matrix sharply decreased with both increasing clay content and processing times. Significantly higher viscosity levels were obtained for the blends in comparison with those of the neat polymer. The DMTA spectra showed higher glass‐transition temperatures for the nanocomposites in comparison with those of the neat EVOH. However, at high clay loadings, the glass‐transition temperature remained constant, presumably because of an adverse plasticizing effect of the low moleculared mass onium ions treating the clays. The storage modulus improved when clay treated for EVOH was used, and it deteriorated when amine‐cured epoxy clay was incorporated, except for the sonicated clay. TGA results showed significant improvements in the blends' thermal stability in comparison with that of the neat EVOH, which, according to TEM, was greater for the intercalated structures rather than for exfoliated ones. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1741–1753, 2002     

Influence of the compatibilizer polarity and molar mass on the morphology and the gas barrier properties of polyethylene/clay nanocomposites

In this study, different modified polyethylenes with different molar masses and different modification rates were examined as compatibilizers to prepare high density polyethylene/organoclay nanocomposites. Nanocomposites having 5 wt % organo-modified clay and 20 wt % interfacial agent were prepared by melt blending. The effect of compatibilizer molar mass and polarity was investigated on the clay dispersion and on the gas barrier properties. It was observed that the amount of large and dense fillers aggregates was considerably reduced by introduction of an interfacial agent. The nanocomposite final morphology was governed by a diffusion/shear mechanism. A high degree of clay delamination was obtained with the high molar mass compatibilizers, whereas highly swollen clay aggregates resulted from the incorporation of the low molar mass interfacial agents. In the investigated nanocomposites series, the barrier properties could not be directly related to the clay dispersion state but resulted also from the matrix/clay interfacial interactions. A gas transport mechanism based on these both parameters was proposed to explain the barrier properties evolution in these low polar nanocomposites series. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2593–2604, 2008