Electrochemical detection of amino acids at carbon nanotube and nickel-carbon nanotube modified electrodes

The oxidation and enhanced detection of traditionally 'non-electroactive' amino acids at a single-wall carbon nanotube (SWNT) surface and at a nickel hydroxide film electrochemically deposited and generated upon the SWNT layer is reported. Different CNT are compared, with Nafion-dispersed SWNT offering the most favorable layer for constant-potential amperometric detection. Factors affecting the oxidation process, including the pH or applied potential, are assessed. The response of the SWNT-Nafion coated electrode compares favorably with that of copper and nickel disk electrodes under flow injection analysis (FIA) conditions. The electrodeposition of nickel onto the SWNT-Nafion layer (Ni-CNT) led to a dramatic enhancement of the analytical response (vs. that observed at the SWNT or nickel electrodes alone). The oxidative process at the Ni(OH)(2) layer has been studied and the increase in sensitivity rationalized. In the presence of amino acid the Ni-CNT layer undergoes an electrocatalytic process in which the amino acid reduces the newly formed NiO(OH) species. Furthermore, the attractive response of both the CNT and Ni-CNT layers has allowed these electrodes to be used for constant-potential FIA of various amino acids and indicates great promise for monitoring chromatographic effluents. Once again an improved signal was observed at the Ni-CNT electrode compared to nickel deposited upon a bare glassy carbon electrode (Ni-GC).     

Electrochemical parameters of ethamsylate at multi-walled carbon nanotube modified glassy carbon electrodes

In this paper, some electrochemical parameters of ethamsylate at a multi-walled carbon nanotube modified glassy carbon electrode, such as the charge number, exchange current density, standard heterogeneous rate constant and diffusion coefficient, were measured by cyclic voltammetry, chronoamperometry and chronocoulometry. The modified electrode exhibits good promotion of the electrochemical reaction of ethamsylate and increases the standard heterogeneous rate constant of ethamsylate greatly. The differential pulse voltammetry responses of ethamsylate were linearly dependent on its concentrations in a range from 2.0 x 10(-6) to 6.0 x 10(-5) mol L(-1), with a detection limit of 4.0 x 10(-7) mol L(-1).     

血红蛋白在纳米羟基磷灰石修饰的热解石墨电极上的直接电化学

采用超声辅助沉淀法合成羟基磷灰石纳米晶体,制作了以纳米羟基磷灰石(HAp)修饰的热解石墨电极(EPG)。并研究了血红蛋白在该修饰电极上的直接电化学行为。在pH6.9的磷酸盐(PBS)缓冲溶液中,得到一对可逆的血红蛋白辅基血红素Fe(Ⅲ)/Fe(Ⅱ)电对的循环伏安氧化还原特征峰,式量电位E0p′=-0.356V(vs.SCE,pH6.9),几乎不随扫速的改变而变化,电子转移数为1.041,近似一个辅基发生一个电子转移。Hb在HAp/EPG电极表面直接电子转移的速率常数为0.6074。在该纳米HAp微环境中,Hb与EPG电极之间的电子传递得到极大促进,并显示了较好的稳定性。式量电势pH3.6~9.0范围内与溶液的pH成线性关系,直线斜率为-56.0mV/pH,说明Hb的电子传递过程伴随质子的转移。探讨了Hb-HAp修饰电极对H2O2的电催经性质,为制作生物传感器打下基础。     

Voltammetry and amperometric detection of tetracyclines at multi-wall carbon nanotube modified electrodes

The voltammetric behaviour and amperometric detection of tetracycline (TC) antibiotics at multi-wall carbon nanotube modified glassy carbon electrodes (MWCNT-GCE) are reported. Cyclic voltammograms of TCs showed enhanced oxidation responses at the MWCNT-GCE with respect to the bare GCE, attributable to the increased active electrode surface area. Hydrodynamic voltammograms obtained by flow-injection with amperometric detection at the MWCNT-GCE led us to select a potential value E _det = +1.20 V. The repeatability of the amperometric responses was much better than that achieved with bare GCE (RSD ranged from 7 to 12%), with RSD values for i _p of around 3%, thus demonstrating the antifouling capability of MWCNT modified electrodes. An HPLC method with amperometric electrochemical detection (ED) at the MWCNT-GCE was developed for tetracycline, oxytetracycline (OTC), chlortetracycline and doxycycline (DC). A mobile phase consisting of 18:82 acetonitrile/0.05 mol L⁻¹ phosphate buffer of pH 2.5 was selected. The limits of detection ranged from 0.09 μmol L⁻¹ for OTC to 0.44 μmol L⁻¹ for DC. The possibility to carry out multiresidue analysis is demonstrated. The HPLC-ED/MWCNT-GCE method was applied to the analysis of fish farm pool water and underground well water samples spiked with the four TCs at 2.0 × 10⁻⁷ mol L⁻¹. Solid-phase extraction was accomplished for the preconcentration of the analytes and clean-up of the samples. Recoveries ranged from 87 ± 6 to 99 ± 3%. Under preconcentration conditions, limits of detection in the water samples were between 0.50 and 3.10 ng mL⁻¹.     

Investigation of modified basal plane pyrolytic graphite electrodes: definitive evidence for the electrocatalytic properties of the ends of carbon nanotubes

The basis of the electrocatalytic nature of multi-wall carbon nanotubes is suggested to reside in electron transfer from the ends of nanotubes, which structurally resemble the behaviour of edge plane (as opposed to basal plane) graphite, and is demonstrated via the comparison of the electrochemical oxidation of epinephrine and the electrochemical reduction of ferricyanide at nanotube-modified electrodes using different types of graphite electrodes and with C(60)-modified electrodes.     

Multi-walled carbon nanotube modified basal plane pyrolytic graphite electrodes: Exploring heterogeneity, electro-catalysis and highlighting batch to batch variation

We highlight the heterogeneity and electro-catalysis of multi-walled carbon nanotubes which is shown to be dependant on batch to batch variation via the use of cyclic voltammetry, X-ray photoelectron spectroscopy and transmission electron microscopy. Batch to batch variation is often an overlooked parameter which may limit their use in electrochemistry, and in particular, in the development and realisation of commercial electroanalytical sensors and therefore needs to be considered.     

Electrocatalysis and amperometric detection of organic peroxides at modified carbon-paste electrodes

Cobalt-phthalocyanine modified carbon-paste electrodes are shown to catalyze the electro-oxidation of organic peroxides. Cyclic voltammetry offers useful insights into the catalytic behavior. Such behavior is exploited for developing an effective amperometric detection scheme for butanone peroxide, cumene hydroperoxide and tert-butyl hydroperoxide with optimum response at a potential of +0.70 V (vs. Ag/AgCl). Highly sensitive and stable flow injection measurements, with detection limits of 2.4-8.3 ng and relative standard deviations of 1.7-1.8% (n = 30), are reported. Applicability to measurements in drinking water is illustrated.     

Electrocatalysis of oxygen reduction on glassy carbon electrodes modified with anthraquinone moieties

Anthraquinone groups were electrochemically grafted to glassy carbon (GC) electrodes via methylene linker to study the oxygen reduction reaction (ORR) in alkaline medium. Two different anthraquinone derivatives, 2-bromomethyl-anthraquinone or 2-chloromethyl-anthraquinone, were used to modify the GC electrode surface. Several modification conditions encompassing potential cycling and electrolysis at a fixed potential were employed in order to vary the surface concentration of MAQ groups (Γ _MAQ) and to study the dependence of the O₂ reduction behaviour on electrografting procedure. Cyclic voltammetry confirmed the presence of anthraquinone moieties attached to the GC electrode and Γ _MAQ varied in the range of (0.5–2.4)?×?10^?10 mol cm^?2. Oxygen reduction was studied on MAQ-modified GC electrodes of various surface coverage using the rotating disc electrode (RDE) and rotating ring-disc electrode (RRDE) methods. The RDE and RRDE results of O₂ reduction reveal that GC/MAQ electrodes show rather similar electrocatalytic behaviour towards the ORR yielding hydrogen peroxide as the final product.     

Peroxidase activity of enzymes bound to the ends of single-wall carbon nanotube forest electrodes

This communication reports the first example, to our knowledge, of enzymes covalently attached onto the ends of vertically oriented single-wall carbon nanotube (SWNT) forest arrays used as electrodes. Quasi-reversible Fe^III/Fe^II voltammetry was observed for the iron heme enzymes myoglobin and horseradish peroxidase coupled to carboxylated ends of the nanotube forests by amide linkages. Results suggest that the “trees” in the nanotube forest behaved electrically similar to a metal, conducting electrons from the external circuit to the redox sites of the enzymes. Electrochemically manifested peroxidase activity of myoglobin and horseradish peroxidase attached to the SWNT forests was demonstrated, with detection limits for hydrogen peroxide in buffer solutions of ∼100 nM. These prototype SWNT-forest biosensors are easy to prepare, and enzyme layers were stable for weeks.     

Detection of homocysteine at carbon nanotube paste electrodes

The use of a carbon-nanotube paste (CNTP) electrode provides an effective means for the determination of homocysteine. A decrease of ca. 120 mV in the overpotential for the oxidation of homocysteine compared to a traditional carbon paste electrode, is reported along with greatly enhanced signal-to-noise characteristics. The analytical parameters have been assessed with a linear range from 5 to 200 μM and a detection limit of 4.6 μM. Furthermore, the generic nature of this increased reactivity of the CNTP surface towards thiol moieties has been demonstrated with cysteine, glutathione and n-acetylcysteine, providing a greatly enhanced electrochemical response compared to the carbon paste electrode.     

Insights into the electro-oxidation of hydrazine at single-walled carbon-nanotube-modified edge-plane pyrolytic graphite electrodes electro-decorated with metal and metal oxide films

Electrochemistry of edge-plane pyrolytic graphite electrodes (EPPGEs) modified with Aldrich single-walled carbon nanotubes (SWCNTs) electro-decorated with metal (Ni, Fe and Co) and their oxides have been studied. The morphology and identity of the metallic dispersions were examined by scanning electron microscopy and energy-dispersive spectroscopy. We show that SWCNTs serve as efficient conducting carbon material for electronic communication between metal films and the underlying carbon electrode. By using cyclic voltammetry and electrochemical impedance spectroscopy (EIS) techniques, it is proved that both EPPGE-SWCNT-Ni and EPPGE-SWCNT-Fe exhibit comparable electrochemical response in buffered aqueous solution (pH 7.0) and towards electro-oxidation of hydrazine in Na₂SO₄ solution. The impedance spectra of these SWCNT-metal hybrids were complicated and follow electrical equivalent circuit model typical of adsorption-controlled charge transfer kinetics. Hydrazine impedance spectra exhibited inductive loop, characteristic of Faradaic current being governed by the occupation of an intermediate state. On the other hand, the EIS data obtained in a simple redox probe, [Fe(CN)₆]³⁻/[Fe(CN)₆]⁴⁻, showed that EPPGE-SWCNT and EPPGE-SWCNT-Ni followed electrical equivalent circuit models typical of partial charge transfer or adsorption-controlled kinetics with some resemblance to the behaviour of electrolyte–insulator–semiconductor sensors.     

Manufacture and evaluation of carbon nanotube modified screen-printed electrodes as electrochemical tools

Carboxylated multiwalled carbon nanotubes (MWCNT-COOH) dissolved in a mixture of DMF:water were used to modify the surfaces of commercially available screen-printed electrodes (SPEs). The morphology of the MWCNT-COOH and the modified SPEs was characterized by transmission electron microscopy (TEM) and scanning electron microscopy (SEM), respectively. SEM analysis showed a porous structure formed by a film of disordered nanotubes on the surface of the working electrode.The modification procedure with MWCNT-COOH was optimised and it was applied to unify the electrochemical behaviour of different gold and carbon SPEs by using p-aminophenol as the benchmark redox system. The analytical advantages of the MWCNT-COOH-modified SPEs as voltammetric and amperometric detectors as well as their catalytic properties were discussed through the analysis, for instance, of dopamine and hydrogen peroxide. Experimental results show that the electrochemical active area of the nanotube-modified electrode increased around 50%. The repeatability of the modification methodology is around 6% (R.S.D.) and the stability of MWCNT-COOH-modified SPEs is ensured for, at least, 2 months.     

Electrochemical oxidation of catecholamines and catechols at carbon nanotube electrodes

The differences in the electrochemical oxidation of two commonly known catecholamines, dopamine and norepinephrine, and one catechol, dihydroxyphenylacetic acid (DOPAC), at three different types of carbon based electrodes comprising conventionally polished glassy carbon (GC), nitrogen-doped carbon nanotubes (N-CNTs), and non-doped CNTs were assessed. Raman microscopy and X-ray photoelectron spectroscopy (XPS) were employed to evaluate structural and compositional properties. Raman measurements indicate that N-CNT electrodes have ca. 2.4 times more edge plane sites over non-doped CNTs. XPS data show no evidence of oxygen functionalities at the surface of either CNT type. N-CNTs possess 4.0 at. % nitrogen as pyridinic, pyrrolic, and quaternary nitrogen functionalities that result in positively charged carbon surfaces in neutral and acidic solutions. The electrochemical behavior of the various carbon electrodes were investigated by cyclic voltammetry conducted in pH 5.8 acetate buffer. Semiintegral analysis of the voltammograms reveals a significant adsorptive character of dopamine and norepinephrine oxidation at N-CNT electrodes. Larger peak splittings, DeltaE(p), for the cyclic voltammograms of both catecholamines and a smaller DeltaE(p) for the cyclic voltammogram for DOPAC at N-CNT electrodes suggest that electrostatic interactions hinder oxidation of cationic dopamine and norepinephrine, but facilitate anionic DOPAC oxidation. These observations were supported by titrimetry of solid suspensions to determine the pH of point of zero charge (pH(pzc)) and estimate the number of basic sites for both CNT varieties. This study demonstrates that carbon purity, the presence of exposed edge plane sites, surface charge, and basicity of CNTs are important factors for influencing adsorption and enhancing the electrochemical oxidation of catecholamines and catechols.     

Electrochemistry at carbon nanotube forests: sidewalls and closed ends allow fast electron transfer

The electrochemical properties of the closed ends and sidewalls of pristine carbon nanotube forests are investigated directly using a nanopipet electrochemical cell. Both are shown to promote fast electron transfer, without any activation or processing of the carbon nanotube material required, in contrast to the current model in the literature.     

多壁碳纳米管修饰电极用于离子色谱分离电活性氨基酸的安培检测

将经羧基化的多壁碳纳米管(MWNTs)修饰在玻碳电极表面,制得碳纳米管修饰电极,并通过循环伏安法研究了某些可氧化的氨基酸在该电极上的电催化行为。该电极对半胱氨酸,色氨酸和酪氨酸有明显的电催化作用,且具有较高的灵敏度和稳定性。在一定的色谱条件下,经过离子色谱分离,这些可氧化的氨基酸的检测限分别为:半胱氨酸7.0×10-7mol L;色氨酸2.0×10-7mol L;酪氨酸3.5×10-7mol L(3倍信噪比)。方法已用于头发中这些氨基酸含量的测定。     

Detection of dopamine using self-assembled diazoresin/single-walled carbon nanotube modified electrodes

Ultrathin films of diazoresin(DR)/single-walled carbon nanotube(SWNT) were fabricated on thioglycollic acid(TGA) decorated gold(Au) electrodes by the self-assembly method combined with the photocrosslinlcing technique.The electrochemical behavior of dopamine(DA) at the DR/SWNT modified electrodes was studied using the cyclic voltammetry(CV) and differential pulse voltammetry(DPV) methods.Under the optimal conditions,a linear CV response to DA concentration from 1 μmol/L to 40 μmol/L was observed,and the detection limit of DA was 2.1 ×10~(-3) μmol/L via the DPV method in the presence of 10 μmol/L of uric acid(UA) or 2.5 × 10~(-3) μmol/L via the DPV method in the presence of10 μmol/L of ascorbic acid(AA).Moreover,the modified electrodes exhibited good reproducibility and sensitivity,demonstrating its feasibility for analytical purposes.     

Design of a new hypoxanthine biosensor: xanthine oxidase modified carbon film and multi-walled carbon nanotube/carbon film electrodes

A new and simple-to-prepare hypoxanthine biosensor has been developed using xanthine oxidase (XOD) immobilised on carbon electrode surfaces. XOD was immobilised by glutaraldehyde cross-linking on carbon film (CF) electrodes and on carbon nanotube (CNT) modified CF (CNT/CF). A comparison of the performance of the two configurations was carried out by the current response using amperometry at fixed potential; the best characteristics being exhibited by XOD/CNT/CF modified electrodes. The effects of electrolyte pH and applied potential were evaluated, and a proposal is made for the enzyme mechanism of action involving competition between regeneration of flavin adenine dinucleotide and reduction of hydrogen peroxide. Under optimised conditions, the determination of hypoxanthine was carried out at ?0.2 V vs. a saturated calomel electrode (SCE) with a detection limit of 0.75 μM on electrodes with CNT and at ?0.3 V vs. SCE with a detection limit of 0.77 μM on electrodes without CNT. The applicability of the biosensor was verified by performing an interference study, reproducibility and stability were investigated, and hypoxanthine was successfully determined in sardine and shrimp samples.     

大黄酸修饰电极对细胞色素C的催化还原

研究了大黄酸修饰电极的性质及对细胞色素C的催化还原，并研究了其电极应用机理。     

尿酸和叶酸存在下改性碳纳米管糊电极上多巴胺电催化氧化MohammadMazloum-Ardakani,MahboobeAbolhasani,Bibi-FatemehMirjalili,MohammadAliSheikh-Mohseni,AfsanehDehghani-Firouzabadi,AlirezaKhoshroo简

A chemically modified carbon paste electrode (CPE), consisting of 2,2''-[(1E)-(1,2-phenylenebis(azanylylidene)] bis(methanylylidene)]bis(benzene-1,4-diol) (PBD) and multiwalled carbon nanotubes (CNTs), was used to study the electrocatalytic oxidation of dopamine using cyclic voltammetry, chronoamperometry, and differential pulse voltammetry (DPV). First, the electrochemical behavior of the modified electrode was investigated in buffer solution. Then the diffusion coefficient, electrocatalytic rate constant, and electron-transfer coefficient for dopamine oxidation at the surface of the PBD-modified CNT paste electrode were determined using electrochemical approaches. It was found that under optimum conditions (pH = 7.0), the oxidation of dopamine at the surface of such an electrode occurred at about 200 mV, lower than that of an unmodified CPE. DPV of dopamine at the modified electrode exhibited two linear dynamic ranges, with a detection limit of 1.0 μmol/L. Finally, DPV was used successfully for the simultaneous determination of dopamine, uric acid, and folic acid at the modified electrode, and detection limits of 1.0, 1.2, and 2.7 μmol/L were obtained for dopamine, uric acid, and folic acid, respectively. This method was also used for the determination of dopamine in a pharmaceutical preparation using the standard addition method.     

Electrocatalysis at chemically modified electrodes : Detection/determination of redox gaseous species in continuous-flow systems

The electrocatalytic response of chemically modified carbon paste and glassy carbon electrodes with anchored Fe(II)/Fe(III) centers is presented for gaseous species such as NO₂, SO₂, H₂S, and Cl₂. Carbon paste electrodes are modified by direct admixing of tris[4,7-diphenyl-1,10-phenanthroline]iron(II) perchlorate, and glassy carbon electrodes are modified by oxidative electropolymerisation of tris[5-amino-1,10-phenanthroline]iron(II) perchlorate. The electrocatalytic cycle operating in the integrated reaction/pre-electrode layer of chemically modified electrodes results in significant signal enhancement. Chemical modification of the conducting surfaces protects the electrode surface from poisoning. evaluation was done in a continuous-flow system using gravitational flow fo supporting electrolyte carrier propulsion, direct injection of air containing parts per billion or parts per million (v/v) of the gaseous species, and amperometric detection with the chemically modified electrodes as part of a thin-layer cell.