Determination of sulphathiazole in the presence of sulphametazine by first-derivative solid-phase spectrophotometry

Sulphathiazole in the presence of sulphametazine is determined by a method based on derivative solid-phase spectrophotometry. Both compounds are fixed on a dextran-type cation-exchange gel. The absorbance of the gel, packed in a 1-mm silica cell, is measured directly. The range of application is between 0.20 and 18.0 g/ml of sulphathiazole in the presence of up to 20 g/ml of sulphametazine, the relative standard deviation is 0.6% and the detection limit is 0.05 g/ml. The method has been applied to the determination of sulphathiazole in synthetic mixtures and pharmaceuticals, with recoveries of 95.0 to 102.5%     

Anwendung der Ringofenmethode zum Nachweis einiger Heteroelemente in organischen Verbindungen

Zusammenfassung Ein schnelles und einfaches Mikroverfahren zum Nachweis einiger Heteroatome organischer Verbindungen wurde entwickelt. Nach Aufschluß mit metallischem Kalium werden die entstehenden Ionen mit der Ringofenmethode getrennt und mit empfindlichen Reaktionen nachgewiesen. Nachweisgrenze: 0,5 bis 1g Stickstoff, 1 bis 2g Schwefel, 2 bis 3g Jod, 4 bis 5g Brom, 5 bis 10g Chlor in 0,5 bis 1 mg Einwaage.

---

Summary A rapid and simple micromethod was developed for the detection of several hetero-elements in organic compounds. After breaking down the sample with metallic potassium, the resulting ions are separated by the ring oven method and detected by means of sensitive reagents. Detection limits: 0.5 to 1g nitrogen, 1 to 2g sulfur, 2 to 3g iodine, 4 to 5g bromine, 5 to 10g chlorine in samples weighing 0.5 to 1 mg.

---

Résumé On a découvert un procédé à l'échelle micro, simple et rapide, pour rechercher certains hétéroéléments dans les composés organiques. Après mise en solution par le potassium métallique, on sépare les ions formés suivant la méthode du four annulaire et l'on effectue la recherche au moyen de réactions sensibles. Limite de dilution: 0,5 à 1g d'azote, 1 àg de soufre, 2 àg d'iode, 5 à 10g de chlore sur 0,5 à 1 mg de prise d'essai.

     

Flow injection analysis at μl/min flow rates

The characteristics of knitted open tube (KOT) figure eight reactors and coil reactors at l/min flow rates were compared using plate height (H) calculations and peak height measurements. Peak broadening independent of flow rate was seen for the figure eight KOT but not the coil at flow rates of 150–300 l/min. Below 150 /min, the plate height values of both reactors were inversely proportional to flow rate. It was concluded that a 0.5-m KOT figure eight reactor is the most effective way to introduce delay time for a 1 1 injection size and tubing of 0.3 mm I.D. Enhancement of peak height response was particularly pronounced at flow rates less than 100 l/min.     

Effect of Surfactants on the Immobilization of 4-(2-Pyridylazo)resorcinol on Silochroms

The effect of cationic surfactants (cetyltrimethylammonium bromide, cetylpyridinium bromide, and tetrabutylammonium perchlorate) and a nonionic surfactant (OP-7) on the conditions of the immobilization of 4-(2-pyridylazo)resorcinol (PAR) on three types of silica gel (Silochrom S-120 (200–350 m), Silochrom S-120 (315–500 m), and Silochrom S-80 (200–350 m)) was studied. It was found that OP-7 does not affect the adsorption of surfactants. The effect of cationic surfactants increases in the order tetrabutylammonium perchlorate < cetyltrimethylammonium bromide < cetylpyridinium bromide. The adsorption activity of silica gels increases in the order Silochrom S-120 (315–500 m) < Silochrom S-80 (200–350 m) < Silochrom S-120 (200–350 m). Cetylpyridinium bromide provides full immobilization of PAR on silica gel Silochrom S-120 (200–350 m) in the pH range 2–9.     

Study of the absorption spectra of the 4f electron transition of the Nd and Er complexes with 2-isobutylformyl-1,3-dione-indane in the presence of TX-100 and its analytical application

The absorption spectra of 4f electron transitions of the systems of neodymium and erbium with 2-isobutylformyl-1,3-dione-indane and TX-100 have been studied by normal and derivative spectrophotometry. Their molar absorptivities at the maximum absorption bands are about 7.2 (at 571 nm) times greater for neodymium and 13.1 (at 519 nm) times greater for erbium than those in the absence of the complexing agents. Use of second derivative spectra both eliminates the interference from other rare earths and increases the sensitivity from neodymium and erbium. Beers law is obeyed from 020 g/ml for neodymium and 025 g/ml for erbium. The relative standard deviations are 1.2% and 1.6% for 5.0 g/ml of neodymium and 8.0 g/ml of erbium, respectively. The detection limits (signal-to-noise ratio=2) are 0.14 g/ml and 0.20 g/ml. A method for the direct determination of neodymium and erbium in rare earth mixtures with good accuracy and selectivity is proposed.     

New cobalt trimethylacetate complexes with pyridine

The reaction of the tetranuclear trimethylacetate complex Co₄(₃-OH)₂(-OOCCMe₃)₄(²-OOCCMe₃)₂(EtOH)₆ with pyridine in acetonitrile was studied. Two new compounds, viz., the hexanuclear cobalt(ii) complex Co₆py₄(₃-OH)₂(-OOCCMe₃)₁₀ (25% yield) and the unusual ionic compound [Co₃py₃(₃-O)(-OOCCMe₃)₆]⁺[Co₄py(₄-O)(-OOCCMe₃)₇]^– (5% yield), were prepared. The structures of the new compounds were established by X-ray diffraction analysis.     

Nickel(II) xanthates with nitrogen heterocycles as bridging ligands

New homopolynuclear nickel(II) xanthate complexes with nitrogen donor heterocycles as bridging ligands have been prepared, namely [Ni(Rxa)2(-L)]n and [Ni2(Rxa)4(-L1)], where R=i-Pr,i-Am; xa=OCS2– L=1,2-bis(4- pyridyl)ethane (bpe), 4,4-dithiodipyridyl (dtp), 1,2-bis(4- pyridyl)ethylene (dpe), 4,4-trimethylene-dipyridine (tmd); L1=2,3-bis(2-pyridyl)pyrazine (bpp), 2,4-bis(5,6- diphenyl-1,2,4-triazine-3-yl)pyridine (bdt), or 2,4,6-tris(2- pyridyl)-1,3,5-triazine (tpt). The compounds have been characterized by elemental analyses, i.r. and electronic spectroscopies, magnetochemical and conductivity measurements. The results show that the [Ni(Rxa)2(-L)]n complexes are linear polymers in which the nitrogen heterocycles bridge between the nickel(II) ions, which are coordinated by four sulfur and two nitrogen atoms and have trans-octahedral geometry. The nearly constant values of the effective magnetic moment (3.36–3.34 eff/B) over the 77–295 K temperature range indicate that exchange interactions are lacking among the paramagnetic centres in the linear structure, [Ni(i-Amxa)2(dpe)]n. The variable- temperature magnetic susceptibilities of the [Ni2(i-Prxa)4(bpp)] (3.00–2.95eff/B per Ni atom), [Ni2(i-Prxa)4(bdt)] (2.72–2.63 eff/B per Ni atom), and [Ni2(i-Amxa)4(tpt)] (2.76–1.87 eff/B per Ni atom) were measured down to liquid nitrogen temperature. In the case of binuclear nickel(II) complexes with bdt or tpt, antiferromagnetic coupling between the nickel(II) ions was detected, giving the exchange integral J=–4.0cm–1 and –29.6cm–1, respectively.     

Semiquantitative estimation of the mycotoxins citrinin, Ochratoxin A, Aflatoxin M1 and penicillic acid on thin-layer chromatograms with a grey scale

Summary Spots of citrinin, ochratoxin A, aflatoxin M₁ and penicillic acid on thin-layer chromatograms can be semi-quantitatively estimated by using a grey scale, commonly used in photo laboratories. The detection limits are 0.01 g for citrinin, 0.006 g for ochratoxin A, 0.002 g for aflatoxin M₁ and 0.01 g for penicillic acid. Standard curves for these mycotoxins are given.

---

Halbquantitative Bestimmung der Mycotoxine Citrinin, Ochratoxin A, Aflatoxin M₁ und Penicillinsäure auf Dünnschicht-Chromatogrammen mit Hilfe eines Graukeils

Zusammenfassung Mit Hilfe eines in Photolabors gebräuchlichen Graukeils können dünnschicht-chromatographische Flecke der obengenannten Mycotoxine halbquantitativ bestimmt werden. Die Nachweisgrenzen betragen 0,01 g für Citrinin, 0,006 g für Ochratoxin A, 0,002 g für Aflatoxin M₁ und 0,01 g für Penicillinsäure. Eichkurven werden angegeben.

     

An Alternative Method of Introducing Fugacity

In current textbooks fugacity is introduced according to its differential or integral mathematical formulation. In this article an alternative method of explanation is offered. It is suggested that the real state of a pure gas can be described by comparing it to a hypothetical idealized state. The differences between these two states can then be expressed in terms of a function, , defined as (T,P) = _real(T,P) - _ideal(T,P) where _real and _ideal are the chemical potentials of the gas in its real and ideal states, respectively. The function is a molar excess quantity and is expressed as (T,P) = RT1n where is the fugacity coefficient. This approach introduces fugacity deductively through the function, which leads to , the fugacity coefficient. This method is also appropriate for introducing the activity of solution components and the fugacity of a real gas in gaseous mixtures.     

Polypyrrole modified stainless steel frits for on-line micro solid phase extraction of ochratoxin A

Polypyrrole (PPy) was electrochemically synthesized on stainless steel frits as a sorbent for the micro solid phase extraction (SPE) of ochratoxin A (OTA). Using 20 l of standard solution under a fast flow rate of 0.5 ml/min, 80% recovery of OTA was achieved in the concentration range from 0.1–10 pg/l. This good recovery was achieved within a short residence time of 1.2 s. A binding capacity of 1 ng OTA was estimated for each PPy-modified frit, or 2 ng OTA for two frits in series. The bound OTA could be pulsed eluted (PE) with 20 l of 1% triethylamine in acetonitrile. On-line coupling of this PPy-on-a-frit and PE technique to high performance liquid chromatography (HPLC) was straightforward. On-line SPE-PE-HPLC results clearly demonstrated the capability of PPy-on-a-frit to bind OTA in the presence of red wine, beer, and orange juice components.     

Electrochemical Intercalation of Lithium Ions into Electrolytic Vanadium Pentoxide

The discharge of thin films of Li _x V₂O₅ is described by a mathematical diffusion model. The chemical diffusion coefficient for lithium ions, estimated with the model, is equal to (1.01–2.5) × 10^–11 cm²/s. As the film thickness increases, the discharge capacity at a current of 20 A/cm² tends to the calculated limiting of 3.12 C/cm². The optimum thickness of the film electrode calculated for a discharge current of 20 A/cm² is 33.4 m and agrees satisfactorily with the experimental value.     

Characterization of airborne particulates by laser microprobe mass analysis

Summary Laser microprobe mass analysis (LAMMA) was applied to characterize aerosol particles collected and separated from 16m to 0.06m by a low pressure cascade impactor. Positive ion LAMMA spectra showed characteristic molecular peaks such as PbCl⁺, a series of Si₂O⁺–Si₂O₄ ⁺ and NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, and TiO⁺ in 0.06–0.12m, 0.5–1m and 4–8m fraction, respectively. In the negative ion LAMMA spectra, it was observed that the fragment peaks of sulfate ions were deficient above 2m and those of nitrate ions were deficient under 2m. LAMMA allows remarkable insights into the chemical nature of aerosol particles.

---

Charakterisierung luftgetragener Teilchen durch Laser-Microprobe-Massenspektrometrie

Zusammenfassung Laser-Microprobe-Spektrometrie (LAMMS) wurde zur Analyse atmosphärischen Aerosols herangezogen, welches im Korngrößenbereich zwischen 16m und 0.06m mit einem Niederdruckkaskadenimpaktor fraktioniert gesammelt wurde. Positive LAMMS-Spektren zeigten charakteristische molekulare Peaks, wie etwa PbCl⁺, eine Serie von Si₂O⁺–Si₂O₄ ⁺ und NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, sowie TiO⁺ in der 0,06–0,12-m,- 0,5–1–m- bzw. 4–8-m-Fraktion. In den negativen LAMMS-Spektren konnten über 2m keine Fragmentpeaks für Sulfationen, unter 2m. keine für Nitrationen beobachtet werden. LAMMS ermöglicht eine bemerkenswerte Einsicht in die chemische Natur von Aerosolteilchen.

     

Hydrogen profiling in thin films using coincident ERD

By using the coincident measurement, an ERD method has been established and used for hydrogen profiling in thin foils. In the present study, 6 MeV has been used as incident particle, the scattered and the recoiled proton from one collision were coincidentally detected at 150 (proton) and 173.9 (). This method has been used for hydrogen profiling of 5.6 m Mylar and 8.6 m aluminium foils. Because of the coincident measurement, the background is largely reduced, and its minimum detection limit is about 0.5% (atomic), lower than the conventional ERD method. The measured depth resolution in 5.6 m Mylar is 0.6 m. It is possible to use this method for hydrogen profiling in thin foils of several micron thickness.     

Simultaneous determination of aluminium and iron in glasses,phosphate rocks and cement using first- and second-derivative spectrophotometry

First- and second-derivative spectrophoto-metric methods for the simultaneous determination of aluminium and iron in their mixtures are described. The methods are based on the colored complexes formed by aluminium and iron with hematoxylin in the presence of cetyltrimethylammonium bromide as a surfactant. The zero-crossing method has been utilized to measure the first- and second-derivative value of the derivative spectrum. Aluminium (0.05–1 gml^-1) could be determined in the presence of iron (0.09–1.6 gml^-1) and vice versa. The detection limits of aluminium and iron are 0.01 and 0.09 gml^-1, respectively in the first-derivative mode and 0.014 and 0.1 gml^-1 in the second-derivative mode. The proposed method has been applied to the simultaneous determination of aluminium and iron in glasses, phosphate rocks, cement and magnesite alloy.     

Selective determination of neodymium and erbium in mixtures with other lanthanides by second-derivative spectrophotometry of complexes with benzoyl-indan-1,3-dione and cetylpyridinium chloride

The absorption spectra of 4f electron transitions of the neodymium and erbium complexes with benzoyl-indan-1,3-dione and cetylpyridinium chloride have been studied by conventional and derivative spectrophotometry. The second-derivative spectrum has been used to eliminate the interference of the other lanthanides, and to increase the sensitivity by a further factor of 4–6. Beer's Law is obeyed for 6–29 g/ml Nd and 7–33 g/ml Er. The relative standard deviations evaluated from 10 independent determinations of 5.0 g/ml Nd and Er were 1.1% (Nd) and 1.6% (Er). The detection limits obtained from the sensitivity of the calibration graphs and 3s _b, (standard deviation of the blank,n = 11) were 0.63 g/ml Nd and 0.61 g/ml Er. The quantification limits (10s _b) were 2.1 g/ml Nd and 2.0 g/ml Er. A method for the direct determination of neodymium and erbium in rare earth mixtures with good accuracy and selectivity is proposed.     

A technique for capillary joining in capillary electrophoresis

Summary Aspects of cracking and joining capillaries have been investigated. Capillary coupling was achieved using various methods. The most successful used hydrofluoric acid-etched capillaries to form male and female ends which were then joined together. This type of joint was used to connect sections of capillary of similar and different internal diameters with minimal loss in resolution, peak width and number of theoretical plates. (Uridine and hypoxanthine was used as a test mixture). For hypoxanthine on a 50 m/50 m etched joined capillary 10 cm from the detector window the number of theoretical plates was 96.6% of that for hypoxanthine on an unbroken capillary. Following the relative success of capillary joining, a coupled capillary flowcell (50 m/200 m) was produced and evaluated.     

Simultaneous determination of copper,mercury and lead by first-order derivative spectrophotometry using dithizone as reagent

A first-order derivative spectrophotometric method has been developed for the simultaneous determination of copper, mercury and lead at g/L levels using dithizone as reagent. The procedure involves the simultaneous extraction of these elements by dithizone in chloroform from weakly alkaline solutions. Linear calibration curves were obtained in the ranges 0.5–10 (Cu), 1–10 (Hg) and 1–10 (Pb) g present in 40 ml of aqueous phase with detection limits of 5 g/L (Cu) and 20 g/L (Hg and Pb). The R.S.D.s for 100 g/L of copper, mercury and lead were 2.5, 2.6 and 3.1% respectively, for 5 determinations. The method is applicable for the determination of copper and lead in marine sediment samples with good precision and accuracy.     

Cleavage of 1,4-diphenylbuta-1,3-diyne on a ruthenium-cobalt cluster: Synthesis and molecular structure of Co2Ru3(μ4−C2Ph)(μ3−C2Ph)(μ-dppm)(μ-CO)2(CO)9

The reaction between Ru₃(₃-²-PhC₂C=CPh)(-dppm)(CO)₈ and Co₂(CO)₈ afforded dark red Co₂Ru₃(₄-C₂Ph)(₃-C₂Ph)(-dppm)(-CO)₂(CO)₉, shown by an X-ray structure determination to contain a strongly twisted Co₂Ru₃ bow-tie cluster (central Co), to which two PhC₂ units derived from cleavage of the original diyne are attached. One a these is strongly interacting with four metal atoms, the other being attached in the familiar ¹,2²-mode. The dppm ligand remains bridging two of the Ru atoms.