Corrosion behavior of electroless Ni–P/TiO2 nanocomposite coatings

Composite Ni–P/nano‐TiO₂ coatings were prepared by simultaneous electroless deposition of Ni–P and nano‐TiO₂ on a low carbon steel substrate. The deposition was carried out from stirred solutions containing suspended nano‐TiO₂ particles. The Ni–P and Ni–P/nano‐TiO₂ coatings before and after heat treatment were characterized by X‐ray diffraction, scanning electron microscopy and energy dispersive X‐ray spectroscopy. The micro‐structural morphologies of the coatings significantly varied with the nano‐TiO₂ content. The corrosion resistance of as‐plated and heat‐treated Ni–P and Ni–P/nano‐TiO₂ coatings was investigated by anodic polarization, Tafel plots and electrochemical impedance spectroscopic (EIS) studies in 3.5% NaCl solution. Ni–P/nano‐TiO₂ coating exhibited superior corrosion resistance over Ni–P coating. Copyright © 2015 John Wiley & Sons, Ltd.     

Preparation of Au-TiO2 Hybrid Nano Particles in Silicate Film Made by Sol-Gel Method

TiO₂ nano particles with photo catalytic property were mixed with silica alkoxides solution with HAuCl₄/4H₂O. STS02 (purchased from Ishihara Sangyo Kaisha, Ltd.) was used as TiO₂ nano particles. The average size of TiO₂ nano particles was 7 nm in diameter. The gel film coated on glass substrate was heated and then HAuCl₄/4H₂O was thermally reduced at 390 degree. The coated silica gel film doped with HAuCl₄/4H₂O and TiO₂ nano particles was turned into light blue from colorless gel film after heat treatment. The optical absorption spectrum showed the absorption peak of the film heated at 390 degree shifted to at about 650 nm compare to SiO₂ film doped with Au nano particles without TiO₂ nano particles that had absorption peak at 542 nm. On the other hand, the film formed from coating solution incorporated TiAA (titanium tetraisopropoxide chelated by acetyl acetone) as TiO₂ source instead of TiO₂ nano particles had absorption peak at 550 nm. That means there was no effect on formation of Au nano particles when TiAA was incorporated. The average size of the particles was found to be about 23 nm in diameter by TEM observation. Furthermore EDX (Energy Dispersive X-ray Fluorescence Spectrometer) analysis of nano particles in the film indicated that Au-TiO₂ nano hybrid particles were formed. Simulation results also supported that the size in diameter of Au nano particles had little influence on the absorption coefficient of the silica film doped with Au nano particles.     

Reducing Photoyellowing of Wool Using Nano TiO2

Wool is the most important animal fiber used in textile industries, but its photostability is very low. Scientists have searched for new ways to increase the photostability of wool. As TiO₂ nano particles have features suitable for new applications, the UV-blocking power of nano TiO₂ may be used for protecting fabrics against UV rays. Treatment of wool with TiO₂ can be effective for controlling photodegradation. This study focused on protecting wool fabric against UV rays using nano TiO₂. To this end, oxidized and raw wool were treated with citric acid as the cross-linking agent and different concentrations of nano TiO₂. The whiteness and yellowness of wool fabric samples were reported. XRD patterns proved the existence of TiO₂ nano-particles on the wool surface. Finally, the results revealed that nano TiO₂ is a suitable UV absorber on wool fabric and its effect depends on concentration.     

Improved Photodegradation of Organic Contaminants Using Nano‐TiO2 and TiO2–SiO2 Deposited on Portland Cement Concrete Blocks

The photocatalytic activity of TiO₂ nanoparticles (nano‐TiO₂) and its hybrid with SiO₂ (nano‐TiO₂–SiO₂) for degradation of some organic dyes on cementitious materials was studied in this work. Nanohybrid photocatalysts were prepared using an inorganic sol–gel precursor and then characterized using XRD, SEM and UV–Vis. The grain sizes were estimated by Scherrer's equation to be around 10 nm. Then, a thin layer was applied to Portland cement concrete (PCC) blocks by dipping them into nano‐TiO₂ and nano‐TiO₂–SiO₂ solution. The efficiency of coated PCC blocks for the photocatalytic decomposition of two dyes, Malachite Green oxalate (MG) and Methylene Blue (MB), was examined under UV and visible irradiation and then monitored by the chemical oxygen demand tests. The results showed that more than 80% and 92% of MG and MB were decomposed under UV–Vis irradiation using blocks coated with nano‐TiO₂–SiO₂. TiO₂/PCC and TiO₂–SiO₂/PCC blocks showed a significant ability to oxidize dyes under visible and UV lights and TiO₂–SiO₂/PCC blocks require less time for dye degradation. Based on these results, coated blocks have increased photocatalytic activity which can make them commercially accessible photocatalysts.     

QUANTUM YIELDS AND KINETICS OF THE PHOTOBLEACHING OF HEMATOPORPHYRIN, PHOTOFRIN II, TETRA(4-SULFONATOPHENYL)-PORPHINE AND UROPORPHYRIN

Abstract Porphyrins used as sensitizers for the photodynamic therapy (PDT) of tumors are progressively destroyed (photobleached) during illumination. If the porphyrin bleaches too rapidly, tumor destruction will not be complete. However, with appropriate sensitizer dosages and bleaching rates, irreversible photodynamic injury to the normal tissues surrounding the tumor, which retain less sensitizer, may be significantly decreased. This paper surveys the quantum yields and kinetics of the photobleaching of four porphyrins: hematoporphyrin (HP), Photofrin II (PF II), tetra(4-sulfonatophenyOporphine (TSPP) and uroporphyrin I (URO). The initial quantum yields of photobleaching, as measured in pH 7.4 phosphate buffer in air, were: 4.7 × 10^-5, 5.4 × 10^-5, 9.8 × 10^-5, and 2.8 × 10^-5 for HP, PF II, TSPP and URO respectively; thus, the rates of photobleaching are rather slow. Low oxygen concentration (2 μM) significantly reduced the photobleaching yields. However, D₂O increased the yields only slightly, and the singlet oxygen quencher, azide, had no effect, even at 0.1 M. Photosensitizing porphyrins in body fluids, cells and tissues may be closely associated with various photooxidizable molecules and electron acceptors and donors. Therefore, selected model compounds in these categories were examined for their effects on porphyrin photobleaching. A number inhibited and/or accelerated photobleaching, depending on the compound, the porphyrin and the reaction conditions. For example, 1.0 mM furfuryl alcohol increased the photobleaching yields of HP and URO more than 5-fold, with little effect on PF II or TSPP. In contrast, the electron acceptor, methyl viologen, increased the photobleaching yield of TSPP more than 10-fold, with little accelerating effect on the other porphyrins. These results suggest that the mechanism(s) of the photobleaching of porphyrin photosensitizers in cells and tissues during PDT may be complex.     

硼铈共掺杂纳米TiO2光催化降解三氯杀螨醇和菊酯类农药

采用溶胶-凝胶法在钛酸丁酯水解过程引入硼酸、硝酸铈,制备具有光催化活性的硼铈共掺杂纳米二氧化钛（TiO2）,经XRD、TEM、FT-IR、UV-Vis-DRS表征晶体结构,在日光灯照射下,光催化降解三氯杀螨醇、高氟氯氰菊酯、氟戊菊酯农药。结果表明：硼铈共掺杂的TiO2只有锐钛矿型,而纯的或掺铈的TiO2有含有锐钛矿型、金红石相和少量板钛矿型,UV-Vis-DRS测定结果表明硼铈共掺杂的TiO2禁带宽度变小,硼铈共掺杂的TiO2在可见光区吸光度高于掺杂铈和不掺杂的TiO2,在420nm~850nm有强的吸收;在同样光照下对三氯杀螨醇、高氟氯氰菊酯、氟戊菊酯的降解试验证明硼铈共掺杂纳米TiO2的光催化活性高于不掺杂或只掺杂铈的TiO2。     

Facile Synthesis of Three‐Dimensional Pt‐TiO2 Nano‐networks: A Highly Active Catalyst for the Hydrolytic Dehydrogenation of Ammonia–Borane

Three‐dimensional (3D) porous metal and metal oxide nanostructures have received considerable interest because organization of inorganic materials into 3D nanomaterials holds extraordinary properties such as low density, high porosity, and high surface area. Supramolecular self‐assembled peptide nanostructures were exploited as an organic template for catalytic 3D Pt‐TiO₂ nano‐network fabrication. A 3D peptide nanofiber aerogel was conformally coated with TiO₂ by atomic layer deposition (ALD) with angstrom‐level thickness precision. The 3D peptide‐TiO₂ nano‐network was further decorated with highly monodisperse Pt nanoparticles by using ozone‐assisted ALD. The 3D TiO₂ nano‐network decorated with Pt nanoparticles shows superior catalytic activity in hydrolysis of ammonia–borane, generating three equivalents of H₂.     

The Shielding Effect of Nano TiO2 on Collagen under UV Radiation

The shielding effect of nano TiO₂ on collagen under UV radiation was investigated using UV spectrophotometry. The results indicate that the shielding of collagen under UV radiation in the presence of nano TiO₂ is significant. For 2.5 wt.‐% of TiO₂, there is a greater shielding effect of UV radiation than that for 0.5 wt.‐% of TiO₂. In addition, this study gives hints that a novel tanning agent with a UV shielding function can be formulated by using nano TiO₂.

UV absorption of collagen under UV radiation after adding 2.5 wt.‐% TiO₂.     

Light conversion efficiency of flower like structure TiO<Subscript>2</Subscript> thin film solar cells

Flower like structure TiO₂ thin films have been grown onto ITO coated glass substrates by sol–gel method. TiO₂ nano flowers have been sensitized using CdS quantum dots prepared using simple precursors by chemical method. The assembly of CdS quantum dots with TiO₂ nano flower has been used as photo-electrode in quantum dot sensitized solar cells. The surface morphology has been studied using scanning electron microscope; it shows that the film exhibits flower like structure. The absorption spectra reveals that the absorption edge of CdS quantum dot sensitized TiO₂ nano flower shifts towards longer wavelength side when compared to the absorption edge of TiO₂ nano flower. The efficiency of the fabricated CdS quantum dot sensitized TiO₂ nano flower based solar cell is 0.66%.     

Sol-gel TiO2 decorated on eggshell nanocrystal as engineered adsorbents for removal of acid dye

Calcined eggshell (CES) food residue was modified by depositing sol-gel titanium dioxide (TiO₂) nanoparticles with narrow size distribution onto it through in situ precipitation and a novel hybrid nano biosorbent, namely TiO₂-CES, was obtained. The deposition was characterized and the TiO₂-CES nano network was used for efficient adsorption of single azo class anionic dye acid red nylon 57 (AN57) from aqueous solutions and the adsorption was pH dependent. Lower pH favored the sorption at the tested different pHs of 1.0–8.0. The calcination temperature had a cogent influence on the adsorption process. The sorption process reached equilibrium within 40?min, and the mathematical models were positively verified and could be described by a pseudo-second-order pattern, while equilibrium was described with Langmuir-type equation. In addition, the reusability study has proven that 0.5?M HNO₃ was efficient enough to desorb AN57 from the hybrid nano sorbent. All results validated that TiO₂-CES is Eco-Friendly adsorbent material practical treatment of dyes contaminated water.     

Enhancing the electrochromic characteristics of conjugated polymer with TiO2 nano‐rods

Organic soluble, oleic acid capped TiO₂ nano‐rod was well‐mixed with the electrochromic polymer: Poly‐(4,4‐dioctylcyclopenta[2,1‐b:3,4‐b′]‐dithiophene (PDOCPDT) to form TiO₂/PDOCPDT nanocompsoite. TiO₂/PDOCPDT film showed high electrochemical stability and its coloration efficiency is 1.5 times of that for pure PDOCPDT. The function of TiO₂ nano‐rods can be regarded as a dispersion agent. PDOCPDT chains in TiO₂/PDOCPDT may have a less aggregated structure and more open morphology, therefore has higher coloration efficiency. TiO₂ may also act as electron transport or temporary electron storage centers, electrons can be transferred reversibly between PDOCPDT and TiO₂ nano‐rods. TiO₂/PDOCPDT is well‐soluble in CHCl₃, large area thin films can be fabricated reproducibly simply by spin coating. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1121–1130, 2008     

Synthesis,characterization and photocatalytic application of TiO2/magnetic graphene for efficient photodegradation of crystal violet

A magnetized nano‐photocatalyst based on TiO₂/magnetic graphene was developed for efficient photodegradation of crystal violet (CV). Scanning electron microscopy, X‐ray diffraction, energy‐dispersive X‐ray spectroscopy and elemental mapping were used to characterize the prepared magnetic nano‐photocatalyst. The photocatalytic activity of the synthesized magnetic nano‐photocatalyst was evaluated using the decomposition of CV as a model organic pollutant under UV light irradiation. The obtained results showed that TiO₂/magnetic graphene exhibited much higher photocatalytic performance than bare TiO₂. Incorporation of graphene enhanced the activity of the prepared magnetic nano‐photocatalyst. TiO₂/magnetic graphene can be easily separated from an aqueous solution by applying an external magnetic field. Effects of pH, magnetized nano‐photocatalyst dosage, UV light irradiation time, H₂O₂ amount and initial concentration of dye on the photodegradation efficiency were evaluated and optimized. Efficient photodegradation (>98%) of the selected dye under optimized conditions using the synthesized nano‐photocatalyst under UV light irradiation was achieved in 25 min. The prepared magnetic nano‐photocatalyst can be used in a wide pH range (4–10) for degradation of CV. The effects of scavengers, namely methanol (OH^? scavenger), p‐benzoquinone (O₂^?? scavenger) and disodium ethylenediaminetetraacetate (hole scavenger), on CV photodegradation were investigated.     

Highly ordered metal oxide nanopatterns prepared by template-assisted chemical solution deposition

TiO₂, Al₂O₃, and ZrO₂ patterns composed of ordered nano motifs of various morphologies (i.e. perforations (craters), rings, canyons, wires, dots, or channels) with typical lateral dimensions of less than 40 nm and thickness below 15 nm are presented. Simple chemical solution deposition (CSD) of molecular inorganic precursors and commercial block copolymers was used to create patterns on several substrate surfaces (bare, hydrophobized or gold covered silicon wafers and ITO). Self-assembly during evaporation and subsequent stabilization at 500 °C leads to the various nanostructures. Compared to other techniques for surface nano patterning, the present method has the advantage of being cheap, reproducible and easy to scale up and does not require specialized equipment. The type, dimension, and organization of these motifs were assessed by AFM, FE-SEM, spectroscopic ellipsometry, and GI-SAXS and are shown to depend on the conditions of preparation. Usage as model surfaces for modelling of wetting properties and as nanoelectrode arrays were investigated.     

Synthesis and Characterization of Poly(methyl methacrylate)-b-Polystyrene/TiO2 Nanocomposites Via Reversible Addition-Fragmentation Chain Transfer Polymerization

A diblock copolymer, poly(methyl methacrylate)-b-polystyrene (PMMA-b-PS), was grafted onto the surface of nano-titania (nano-TiO₂) successfully via reversible addition-fragmentation chain transfer (RAFT) polymerization. The surface of TiO₂ nanoparticles was modified initially by attaching dithioester groups to the surface using silane coupling agent 3-(chloropropyl)triethoxy silane and sodium ethyl xanthate. The polymerization of methyl methacrylate and styrene were then initiated and propagated on the TiO₂ surface by RAFT polymerization. The resulting composite nanoparticles were characterized by means of XPS, FT-IR, ¹H NMR and TGA. The results confirmed the successful grafting of poly(methyl methacrylate) (PMMA) and diblock copolymer chains onto the surface of TiO₂. The amount of PMMA grafted onto the TiO₂ surface increased with the polymerization time. Moreover, the kinetic studies revealed that the ln([M]₀/[M]), where [M]₀ is the initial and [M] is the time dependent monomer concentrations, increased linearly with the polymerization time, indicating the living characteristics of the RAFT polymerization.     

Solgel-hydrothermal synthesis of Tb/Tourmaline/TiO2 nano tubes and enhanced photocatalytic activity

In this study, we synthesized Tb/Tourmaline/TiO₂ nano tubes (NTs) through a solgel-hydrothermal method. The as-prepared samples were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, Raman spectromicroscope, scanning electron microscopy, transmission electron microscopy and UV-vis diffuse reflectance spectroscopy. The resulting Tb/Tourmaline/TiO₂ NTs exhibited higher photocatalytic activity than pure TiO₂ and TiO₂ nano particles (NPs) in the degradation of menthyl orange under UV-light. Results revealed that doping rare earth element Tb could narrow the wide band gap of TiO₂ and tourmaline could trap the photogenerated electron of TiO₂ to inhibit the recombination of photogenerated electron-hole pairs.     

四-(对-磺基苯基)卟啉二酸(H2+4TSPP) 分子聚集体的共振喇曼光谱研究

研究了四-(对-磺基苯基)卟啉二酸(H     

Hybrid TiO2–Ruthenium Nano‐photosensitizer Synergistically Produces Reactive Oxygen Species in both Hypoxic and Normoxic Conditions

Photodynamic therapy (PDT) is widely used to treat diverse diseases, but its dependence on oxygen to produce cytotoxic reactive oxygen species (ROS) diminishes the therapeutic effect in a hypoxic environment, such as solid tumors. Herein, we developed a ROS‐producing hybrid nanoparticle‐based photosensitizer capable of maintaining high levels of ROS under both normoxic and hypoxic conditions. Conjugation of a ruthenium complex (N3) to a TiO₂ nanoparticle afforded TiO₂‐N3. Upon exposure of TiO₂‐N3 to light, the N3 injected electrons into TiO₂ to produce three‐ and four‐fold more hydroxyl radicals and hydrogen peroxide, respectively, than TiO₂ at 160 mmHg. TiO₂‐N3 maintained three‐fold higher hydroxyl radicals than TiO₂ under hypoxic conditions via N3‐facilitated electron–hole reduction of adsorbed water molecules. The incorporation of N3 transformed TiO₂ from a dual type I and II PDT agent to a predominantly type I photosensitizer, irrespective of the oxygen content.     

Highly Efficient,Conjugated‐Polymer‐Based Nano‐Photosensitizers for Selectively Targeted Two‐Photon Photodynamic Therapy and Imaging of Cancer Cells

Two‐photon photodynamic therapy (2P‐PDT) is a promising noninvasive treatment of cancers and other diseases with three‐dimensional selectivity and deep penetration. However, clinical applications of 2P‐PDT are limited by small two‐photon absorption (TPA) cross sections of traditional photosensitizers. The development of folate receptor targeted nano‐photosensitizers based on conjugated polymers is described. In these nano‐photosensitizers, poly{9,9‐bis[6′′‐(bromohexyl)fluorene‐2,7‐ylenevinylene]‐co‐alt‐1,4‐(2,5‐dicyanophenylene)}, which is a conjugated polymer with a large TPA cross section, acts as a two‐photon light‐harvesting material to significantly enhance the two‐photon properties of the doped photosensitizer tetraphenylporphyrin (TPP) through energy transfer. These nanoparticles displayed up to 1020‐fold enhancement in two‐photon excitation emission and about 870‐fold enhancement in the two‐photon‐induced singlet oxygen generation capability of TPP. Surface‐functionalized folic acid groups make these nanoparticles highly selective in targeting and killing KB cancer cells over NIH/3T3 normal cells. The 2P‐PDT activity of these nanoparticles was significantly improved, potentially up to about 1000 times, as implied by the enhancement factors of two‐photon excitation emission and singlet oxygen generation. These nanoparticles could act as novel two‐photon nano‐photosensitizers with combined advantages of low dark cytotoxicity, targeted 2P‐PDT with high selectivity, and simultaneous two‐photon fluorescence imaging capability; these are all required for ideal two‐photon photosensitizers.     

介孔钛纳米复合团簇应用于光热-光动力疗法

在本文,采用水热法合成了一种新型的介孔二氧化钛/碳/亚甲蓝复合纳米团簇(TiO₂@C-MB),并应用于肿瘤细胞的光动力(PDT)和光热治疗(PTT)。系统中介孔二氧化钛作为有效的光敏剂,MB作为重要的光敏添加剂以改善二氧化钛纳米晶的光化学效应,并将其光响应区域拓宽至光动力学疗法的理想治疗窗(650~900 nm)。柠檬酸在水热条件下被还原成碳并裹覆在二氧化钛表面。碳层表现出良好的光热效果,也充当多功能的电子受体以加速生成单线态氧。该纳米团簇不仅可以保持肿瘤细胞内部高浓度的MB和二氧化钛以产生大量的单线态氧杀死肿瘤细胞,而且可以避免MB退化失活。     

Preparation of composited Nano‐TiO2 and its application on antimicrobial and self‐cleaning coatings

Composite nano‐TiO₂ with doping Fe³⁺ and Ag was prepared, and further modified by 3‐methacryloxypropyltrimethoxysilane. They were characterized by Zetasizer Nano ZS Particle and Zeta Potential Analyzer, X‐ray diffraction, UV–Vis spectrophotometer, FT–IR spectra, and transmission electron microscopy. The modified composite nano‐TiO₂ was applied to prepare multifunctional fluorocarbon coatings (FCC). Antibacterial activity of multifunctional FCC containing modified composite nano‐TiO₂ was investigated. Its photocatalytic antibacterial activity reached 92%. The influence of doping ingredients, amount of composite nano‐TiO₂, different light houses, or surface modification was discussed. The surface of FCC cannot be easily smirched by oiliness, dust or water because of hydrophobic fluorosilicone emulsion. It would be an available modern interior building coating for its remarkable photocatalytic antibacterial property as well as self‐cleaning function. Copyright © 2009 John Wiley & Sons, Ltd.