硅氧烷官能化聚芳醚腈自组装膜的制备及其性能

杂萘联苯聚芳醚腈通过水解、酰化及氨丙基三乙氧基硅烷改性后,合成了侧链含有硅氧烷官能团功能性聚芳醚树脂(PNAS)。采用红外、¹H NMR、固体²⁹Si NMR谱等技术手段对产物结构进行表征,用DSC、TGA和原子力显微镜测试了PNAS树脂的性能和自组装薄膜的表面形貌。结果表明,PNAS具有优异的耐热性,其玻璃化转变温度为329 ℃,热失重温度(T_5%)达到492 ℃。与短链分子自组装膜比较,PNAS自组装薄膜具有良好的减摩抗磨性能,当载荷为400 mN时,自组装薄膜的稳定摩擦系数达到0.07且在5 h内基本不变。     

Structure–Property Relationship of Thin Plasma Deposited Poly(allyl alcohol) Films

Poly(allyl alcohol) films with a thickness of about 150 nm were deposited by pulse plasma polymerization onto different substrates (inorganic and organic). The structure/property relationships of these samples were studied in dependence on the duty cycle (DC) of the plasma by a broad combination of different techniques and probes. For the first time volume sensitive methods (FTIR and dielectric spectroscopy) are combined with surface analytics by employing XPS for that system. FTIR spectroscopy gives qualitatively the same dependence of the concentration of the OH groups on DC like XPS. The observed differences are discussed considering the different analytical depths of both the methods. The dielectric measurements show that the plasma deposited films are not thermally stable but undergo a post plasma chemical reaction during heating. The results obtained by dielectric spectroscopy are discussed in detail with the data from FTIR and XPS measurements.     

右旋聚乳酸薄膜的结晶形态

利用旋涂法制备一系列右旋聚乳酸(PDLA)均聚物薄膜, 在不同溶液浓度、结晶温度、结晶时间、溶剂和基底条件下对其进行等温结晶处理, 得到直径和长度大小不等的短棒和纤维束球状等形态, 利用原子力显微镜(AFM)研究了不同条件下所得到的PDLA薄膜的结晶形态. 提出了可能的结晶演变过程和生长模型. 通过控制不同的结晶条件, 可以得到PDLA均聚物薄膜的不同结晶形态.     

Structure and Mechanical Properties of Chitosan/Poly(Vinyl Alcohol) Blend Films

Summary: The origins of the thermal and mechanical properties of chitosan and poly(vinyl alcohol) (PVA) with inter- and intra-hydrogen bonds were investigated systematically by using X-ray, DSC, positron annihilation and viscoelastic measurements. Based on their individual properties, the characteristics of the blend films were estimated in relation to their morphology and mechanical properties as a function of chitosan content. The characteristics of the blend films were also analyzed in terms of the deviation from a simple additive rule of chitosan and PVA content. These results suggested that the miscibility of chitosan and PVA could be ensured by entanglement of the amorphous chain segments of chitosan and PVA. Further detailed analysis revealed that the chitosan content on the film surface is higher than that of the admixture content of chitosan after elongation, although the chitosan and PVA chains were crystallized independently. The elongation could be achieved for the blend films whose PVA content was higher than 50% and the drawn blend films were transparent. Thus, it may be expected that sufficiently entangled meshes formed between chitosan and PVA amorphous chains within the film, the PVA content being higher than 50%, were maintained under the elongation process.     

Poly(3,4-ethylenedioxythiophen)/Poly(4-styrenesul-fonate): Thin Films and Microfibers

This Feature Article describes our recent researches on processing poly(3,4-ethylenedioxythiophene /poly(4-styrenesulfonate) (PEDOT/PSS) colloidal dispersion into thin films which exhibit high conductivity and high transparency, and into microfibers which exhibit high conductivity and high mechanical strength. The state-of-the-art thin films and microfibers are expected to utilize to sophisticated touch screens and wearable electronic devices as organic transparent electrodes and woven electric circuits, respectively.     

Effect of Phase Transitions on Adsorption Properties of Thin Ferroelectric Poly(vinylidene fluoride-co-trifluoroethylene) Films

The adsorption isotherms of water, oxygen, and hexane molecules at the surface of poly(vinylidene fluoride-co-trifluoroethylene) films 30 and 5 monolayers thick obtained by the Langmuir–Schaefer technique were measured at various temperatures using quartz crystal microbalance. An effect of a ferroelectric phase transition occurring at a temperatures from 363 to 388 K on the adsorption activity of the films of the both thicknesses was disclosed. The highest adsorption was observed at a temperature T 380 K. In the case of the superthin copolymer film 5 monolayers thick, one more maximum of the adsorbability was detected at T 300 K that corresponded to a low-temperature phase transition, which is typical of only the copolymer films thinner than 30 monolayers. The effects observed were explained by the facilitation of an adsorbate diffusion into the copolymer film upon its structural rearrangement caused by the phase transition. The results of this study allowed us to propose a new method for the determination of structural phase transitions based on studying isotherms of molecular adsorption from the gaseous phase.     

Aluminum Antimonide Thin Films: Structure and Properties

Protocols for sputtering stoichiometric aluminum antimonide thin films were developed by calculating aluminum and antimony vapor condensation flux densities. Aluminum and antimony were sputtered separately. The high chemical reactivity of nanosized aluminum and antimony films made it possible to reduce the synthesis temperature considerably (far below the melting point of the compound). The synthesis involved thermal annealing. The reaction between aluminum and antimony films started at 470°С. Optimal AlSb formation parameters comprise annealing at 540°С for at least 10 h. Film synthesis steps were studied by X-ray powder diffraction, optical, electron, and atomic force microscopy. The composition was monitored by energy dispersive X-ray spectra. The films were found to have hole conductivity; the 300-K charge density and charge mobility in the films are 1 × 10¹⁹ cm^–3 and 1 × 10² cm²/(V s), respectively.     

聚(ε-己内酯)薄膜结晶形貌及分子取向研究

用匀胶机通过溶液铸膜方法在硅片和铝箔基板上分别制备具有不同厚度的聚(ε-己内酯)(PCL)薄膜. 通过原子力显微镜(AFM)和偏光衰减全反射傅里叶红外光谱(ATR-FTIR)对薄膜中PCL的结晶形貌、 片晶生长方式及分子链取向进行了研究. AFM结果表明, 在200 nm或更厚的薄膜中, PCL主要以侧立(edge-on)片晶的方式生长; 对于厚度小于200 nm的薄膜, PCL片晶更倾向于以平躺(flat-on)的方式生长. 这种片晶生长方式的改变在硅片和铝箔基板上都表现出同样的倾向. 此外, 在15 nm或更薄的薄膜中, PCL结晶由通常的球晶结构变为树枝状晶体. 偏光ATR-FTIR结果表明, 当膜厚小于200 nm时, 薄膜结晶中PCL分子链沿垂直于基板表面方向取向, 并且膜越薄, 取向程度越高, 与AFM的观测结果一致.     

层层自组装聚烯丙胺盐酸盐/Pd纳米复合薄膜的制备及其电催化特性

利用层层静电自组装技术将聚烯丙胺盐酸盐(PAH)和四氯合钯酸根离子( )交替沉积在基底上, 然后用硼氢化钠还原, 构筑了含钯纳米粒子的PAH/Pd纳米复合薄膜. 通过紫外-可见吸收光谱(UV-Vis)、扫描电子显微镜(FESEM), X射线光电子能谱(XPS)和循环伏安(CV)等手段对复合膜的组装、成分、微结构、表面形貌和光学性能进行了测试分析. FESEM图形显示膜表面有一定的粗糙度, 膜上生成了粒径在50～100 nm 范围的钯纳米粒子; UV-Vis结果显示多层膜在特征吸收峰处的吸光度数值随膜双层数增加逐渐增大, 呈良好的线性关系, 表明多层膜是均匀组装的; XPS结果证实了复合膜上有Pd生成, CV结果说明复合薄膜对尿酸的氧化具有较好的电催化活性, 有望用于电化学传感器.     

纳米多孔金薄膜的表面等离子体共振传感特性

对淀积在玻璃衬底上厚度约60 nm的金银合金溅射薄膜进行硝酸腐蚀脱银处理, 得到纳米多孔金薄膜. 利用自建的波长检测型表面等离子体共振(SPR)传感装置研究了腐蚀时间对纳米多孔金薄膜SPR特性的影响, 结果发现纳米多孔金薄膜与水溶液接触后在400-900 nm光谱范围内不具有SPR效应, 而当薄膜置于空气中时会产生明显的传播等离子体共振吸收峰, 其共振波长随腐蚀时间增加逐渐红移. 纳米多孔金薄膜在空气气氛中的SPR效应使其能够用于原位监测气相分子在孔内的吸附, 还可对在液相中吸附的生化分子进行离位测试. 本文对L-谷胱甘肽、L-半胱氨酸、2-氨基乙硫醇三种含巯基的生化小分子在纳米多孔金薄膜内的吸附进行了离位分析, 结果表明与传统的致密金薄膜SPR芯片比较, 纳米多孔金薄膜对这些分子显示出更高的灵敏度和更低的检测下限, 这归功于多孔金的大比表面积使其能够吸附大量的生化小分子. 实验还对乙醇蒸气在纳米多孔金薄膜内的吸附进行了原位监测, 发现吸附平衡所用时间较长, 约为160 min.     

Dynamic Surface Properties of Poly(vinylpyrrolidone) Solutions

The dynamic surface tension and the complex dynamic surface elasticity of poly(vinylpyrrolidone) (PVP) solutions were measured in the concentration range 10(-5) wt% up to about 1 wt%. The surface tension changed slowly with time at low (<10(-4) wt%) and high concentrations (>0.1 wt%). At low concentrations this is a consequence of the slow transport by diffusion of PVP molecules from the depth of the bulk phase to the surface. At high concentrations the time effect is unexpected and probably the result of PVP contamination of high surface activity. The dynamic surface elasticity of PVP solutions gradually decreases with increasing concentration up to the range of high concentrations (>0.1 wt%) where an abrupt increase in the elasticity caused by the adsorbed impurity is observed. At low and medium concentrations the viscoelastic behavior of PVP adsorbed films is similar to that of the previously investigated poly(ethylene oxide) and poly(ethylene glycol) films and is determined by the number of loops and tails protruding into the bulk phase.     

Effect of Surface Roughness on Structure and Dynamics in Thin Films

We performed Monte Carlo simulations of free‐standing, amorphous polyethylene (PE) thin films at 509 K. The three films are constructed from 9, 36, or 144 independent parent PE chains, with 100 carbon atoms per chain. The two‐dimensional periodic cross‐sectional area of the simulation box is proportional to the number of independent parent chains, with the 144‐chain film having an area four times larger than the 36‐chain film. All three films have a similar bulk density and a comparable thickness between the two free surfaces. The 144‐chain film with the largest periodic surface area has a broader density profile due to the increased roughness of its surfaces. Snapshots of its surfaces along the trajectory indicate dynamic changes in the high and low regions of the rough surfaces. Diffusion of the chains parallel to the free surfaces is suppressed in the 144‐chain film, due to increased surface roughness. The tendency of bonds to orient parallel to the free surface is less pronounced in films with higher surface roughness.     

聚(3-己基)噻吩薄膜中电荷传导的研究

对两种具有相同化学结构的聚(3-己基)噻吩膜进行了电荷传导研究以检验膜的结构对载流子迁移率的影响. 一种膜是由3-己基噻吩单体经电化学合成直接制备的膜(原位生长膜); 另一种膜是将原位生长膜溶于三氯甲烷后重新滴涂而成的(滴涂膜). 研究表明, 虽然两种膜的制备方法不一样, 但在最低(0.02%)和较高(20%～30%)掺杂率下两膜中的载流子迁移率相一致; 然而在中等掺杂率区域, 两膜中的载流子迁移率明显不同. 对于原位生长膜, 载流子迁移率在低掺杂区域几乎保持不变, 当掺杂率大于1%后开始上升; 而在滴涂膜中, 随着掺杂率的增加, 迁移率先下降然后迅速升高. 上述两种迁移率变化特征分别与以前研究中观察到的电化学合成高分子膜和化学合成高分子旋涂或滴涂膜中迁移率的变化特征相一致, 表明了迁移率随掺杂率变化特征的改变是由膜的结构变化而引起的     

聚氧乙烯超薄膜中构象变化的红外光谱研究

近年来 ,有关聚合物薄膜的研究受到了广泛关注 .低维数高分子超薄膜的各种行为由于涉及到高分子运动的动力学、热力学本质而逐渐成为高分子科学研究中的一大热点 .实验结果表明[1～ 3] ,几何受限条件和基板对于聚合物薄膜结晶的形态及性能都会产生显著影响 .广角 X射线衍射实验和自由表面的掠入射 X射线实验 [4 ]表明 ,有些在本体中呈现液晶有序的聚酰亚胺在靠近基板附近变得更加有序 .Despotopoulou等 [5] 对聚二正己基硅烷在超薄膜中构象扰动的观察发现 ,当膜厚小于 2 0 0 nm时 ,聚二正己基硅烷的侧链变得无序 ,傅里叶变换红外光谱测试…     

聚对苯二甲酸1,3-丙二醇酯溶液浇铸薄膜形态结构

聚对苯二甲酸1,3-丙二醇酯(PTT)是典型的半结晶聚合物,从熔体结晶形成球品,在某一结晶温度范围内,在球晶中可观察到环带结构,一般认为,环带球品的形成归因于片晶沿球晶径向的周期性扭曲,本文研究了PTT溶液浇铸薄膜在溶剂挥发过程中等温结晶的形态结构。     

Surface and Bulk Structure of Thin Spin Coated and Plasma-Polymerized Polystyrene Films

Polystyrene (PS) spin coated thin films were modified by O₂ and Ar plasma as well as by UV irradiation treatments. The modified PS samples were compared with plasma polymerized and commercial polystyrene. The effects of plasma (O₂ and Ar) and UV irradiation treatments on the surface and the bulk properties of the polymer layers were discussed. The surface properties were evaluated by X-ray Photoelectron Spectroscopy and Contact angle measurements and the bulk properties were investigated by FTIR and dielectric relaxation spectroscopy. As a result only one second treatment time was sufficient to modify the surface. However, this study was also dedicated to understand the effect of plasma and plasma irradiation on the deposited layers of plasma polymers. The dielectric measurements showed that the plasma deposited films were not thermally stable and underwent an undesired post-plasma chemical oxidation.     

聚(2,2＇-二氨基苯氧基二硫化物)结构与性能研究

用动电位连续扫描法制备了聚（2，2'-二氨基苯氧基二硫化物）（PDAPO），通过FT-IR，FT-Raman，XPS等测试技术确证其结构。聚合物产物与其单体的循环伏安实验结果表明，由于PDAPO结构中支链聚苯胺的电催化作用和强供电子键-O-S-S-O-的作用，其氧化还原反应的可逆性优于其它同类的聚有机二硫化物。研究了聚合物的导电性能、热稳定性及表面状态。结果表明，PDAPO是一种新型高电活性的导电聚合物，可用作锂或锂二次电池的正极材料。     

聚乳酸接枝改性纳米生物玻璃/PLGA复合材料的制备、表面性质及生物活性

以丙交酯开环聚合原位接枝改性的纳米生物玻璃(PLLA-g-BG)与聚丙交酯-乙交酯(PLGA)复合材料为研究对象, 采用TGA, ESEM和EDX分析其接枝率, 粒子分散性和表面元素分布, 通过将兔成骨细胞种植于材料膜表面进行体外培养, 采用荧光染色法、NIH Image J图像分析软件、MTT法和流式细胞术等手段检测细胞在材料表面的平均黏附数量、扩展面积比、增殖能力和细胞周期的变化, 综合评价新型改性纳米复合材料的生物相容性和生物活性. 结果表明, 聚乳酸表面接枝改性可明显改善纳米生物玻璃粒子的团聚; PLGA中掺入一定比例的改性PLLA-g-BG可明显促进兔成骨细胞的黏附、扩展与增殖; 改性纳米生物玻璃的应用可提高生物可降解聚酯材料的生物相容性和生物活性.     

Effect of the Surface Structure of Poly(styrene-co-acrolein) Microspheres and Its Modification by Protein on Electrosurface Properties

The electrophoretic mobility of poly(styrene-co-acrolein) microspheres was studied as a function of storage time. It was shown that pH_IEP2.0 is retained but the abnormal dependence of electrophoretic mobility on NaCl concentration is replaced by classical dependence. When comparing chemisorption of bovine serum albumin (BSA) on the microsphere surface for various latex samples, the differences in the isotherm patterns was revealed; moreover, the prevalence of surface concentration of carboxyl groups over that of aldehyde groups resulted in a decrease in adsorption. After the modification of the microspheres by protein, the values of pH_IEPfall within the range of 3.5–5.0 and their dependence on the amount of surface-bound protein passes the minimum. The results obtained are discussed in terms of the different arrangement patterns of protein molecules on the microsphere surface and the changes of BSA macromolecule conformations under the effect of a dispersion medium and as a result of chemical interaction with the polymer surface.     

Preparation and Pyroelectric Properties of Poly(pentafluorostyrene)-r-Poly(4-vinylaniline) Copolymer Films

Abstract: In this study poly(pentafluorostyrene)-ran-poly(4-vinylaniline) (PPFS-r-PVA) was synthesized by solution polymerization with AIBN utilized as an initiator. The dilute THF solution of the resultant copolymer was spin-coated onto clean Ag/Si(100) substrates, and then the copolymer film was electrically poled at 85 °C for 30 min using a plane poling method with a poling voltage of 7.0 kV. The pyroelectric coefficient was determined by a digital integral method and carried out with a charge integral instrument. It was observed that the average pyroelectric coefficient of the resultant PPFS-r-PVA was 20.4 µC/cm²K in the range of 20–45 °C, and the average dielectric loss is about 0.2298 between 3.2 × 10⁴–1.0 × 10⁶ Hz.