从SiCl4合成多孔硅/碳复合材料及储锂性能研究

以Li₁₃Si₄和SiCl₄为原料,通过简单的机械球磨法合成多孔硅/碳复合材料,通过控制Li₁₃Si₄颗粒的尺寸可以有效调节产物的比表面积。分别研究了包覆碳含量、多孔硅/SuperP(导电碳)比表面积以及极片活性物质负载量对多孔硅/碳复合材料电化学性能的影响。结果表明:多孔硅/SuperP比表面积为100.9m₂·g^-1,化学气相沉积(CVD)包覆碳含量为25.3wt%(约6nm厚)的复合材料具有最高的电化学活性,在300mA·g^-1的电流密度下,循环可逆比容量达到1900mAh·g^-1,50次循环后容量仅衰减7.6%。     

碳热还原温度对耐高温纤维增强碳化硅多孔材料组织结构的影响

本研究目的是开发一种耐高温纤维增强碳化硅多孔块状材料。以纤维增强间苯二酚-甲醛/氧化硅复合气凝胶为前驱体,经过1300~1500℃碳热还原制备了纤维增强碳化硅多孔材料。采用XRD、SEM、TEM、氮气吸附孔结构分析仪和压汞仪对纤维增强碳化硅多孔材料的物相组成、微观形貌和孔结构进行了表征,结果表明：纤维增强碳化硅多孔材料由β-SiC和莫来石纤维组成,随着碳热还原温度的升高,样品中的SiC纳米晶颗粒团聚成大块,最终在1500℃生成SiC晶须,升高碳热还原温度会导致样品中大孔的增多和纳米孔的消失以及比表面积的降低。热分析结果表明纤维增强碳化硅多孔材料在空气中的耐温性高达1300℃。纤维增强碳化硅多孔材料的密度为0.330~0.345g·cm^-3,孔隙率在89%以上,室温下热导率为0.06~0.07W·m^-1·K^-1。     

超高比表面积氮掺杂多孔碳材料的制备及其超级电容性能

以蔗糖为碳源,尿素为氮源,草酸钾为活化剂,通过简单的研磨和高温碳化制备了具有超高比表面积(大于3 000 m²·g^-1)的氮掺杂多孔碳材料。采用多种手段对多孔碳材料的微观形貌、比表面积、孔结构和表面氮物种进行了表征,探究了不同温度下草酸钾和尿素对碳材料的比表面积、氮含量和超级电容性能的影响。结果表明,仅使用草酸钾作为活化剂制备的碳材料KC-800 的比表面积为 1 114 m2·g^-1,而同时使用草酸钾和尿素制备的样品 KNC-800 的比表面积高达 3 033 m²·g^-1。在以 6.0mol·L^-1 KOH 为电解液的三电极体系中,当电流密度为 0.5 A·g^-1时,KNC-800 的比电容为 405 F·g^-1,而 KC-800 的比电容仅为248 F·g^-1。这表明草酸钾和尿素的加入显著提高了多孔碳材料的比表面积和超级电容性能。电容贡献分析表明,KNC-800的双电层电容值和赝电容值均高于KC-800。KNC-800在电流密度为0.5 A·g^-1时经过10 000次循环后仍能保持98.3%的初始比电容,表现出优异的循环性能。     

碳载体的预处理对Pt/C催化剂结构和性能的影响

采用一种新的调变多元醇制备方法,通过调节碳载体热处理条件,制备得到不同的Pt/C燃料电池催化剂。采用pH计及物理吸附仪表征碳黑表面的含氧官能团和比表面积,利用电感耦合等离子光谱、X射线衍射、透射电镜和循环伏安法分别表征催化剂的成分、物相组成、微观组织形貌和电化学性能,并与进口的Johnson Matthey(JM) Pt/C催化剂的性能进行对比。结果表明:采用调变多元醇法,以400 ℃热处理碳黑作载体所制备的Pt/C催化剂的电化学比表面积达到83 m²·g^-1,质量电流密度为49.03 A·g^-1。而进口催化剂JM 20% Pt/C的电化学比表面积为77 m²·g^-1,质量电流密度仅11.13 A·g^-1,自制催化剂即使Pt载量降低3wt%~4wt%,其电催化活性仍优于进口催化剂。     

Cu-ETS-10催化NH3选择性还原NOx性能

采用离子交换法制备了Cu-ETS-10钛硅分子筛催化剂,该催化剂对于NH₃选择性催化还原（SCR）NO_x反应具有较高的催化活性、N₂选择性和抗SO₂性能.结果表明,Cu-ETS-10钛硅分子筛具有丰富的微孔结构和较高的比表面积（288-380m²/g）;原子发射光谱、程序升温还原技术和原位红外漫反射等表征结果表明,Cu在Cu-ETS-10钛硅分子筛中具有多种存在形态,其中Cu²⁺物种为Cu-ETS-10的活性中心,其含量随Cu含量的增加而先增后降,与催化活性的变化趋势一致.     

多孔碳负载镍纳米颗粒的制备及催化氨硼烷水解制氢

合成了蜂窝状的分级多孔碳,并以多孔碳为载体通过浸渍-化学还原法制备碳载镍(Ni/C)作为催化氨硼烷水解制氢的催化剂。采用XRD、BET、SEM、Raman、TEM等手段对样品进行了表征并研究了Ni/C室温催化性能。结果显示,多孔碳比表面积高达737 m²·g^-1,具有部分石墨化结构;负载的非晶态镍纳米颗粒平均粒径约为10 nm,均匀分布在碳基材。碳载镍对氨硼烷水解反应具有良好的催化活性,镍负载量为30wt%时催化性能最佳,298 K温度下放氢速率达到1 304.67 mL·min^-1·g^-1,活化能为29.1 kJ·mol^-1,并且具备一定的催化稳定性,表明Ni/C可作为一种廉价高效的催化剂应用于催化氨硼烷水解制氢。     

常温合成硫掺杂微孔碳及其二氧化碳的吸附性能

常温下以间苯三酚和3-甲醛苯并噻吩作为原料,一步法合成了含硫酚醛树脂。在氩气保护下碳化,成功制备出了硫掺杂多孔碳（S-PC）。并利用扫描电镜（SEM）、X射线光电子能谱（XPS）、X射线衍射（XRD）和氮气吸附-脱附仪对材料进行了形貌、结构和性能的表征。实验结果表明,所得样品具有较高比表面积和大量的微孔,经过调控,可以使制备的硫掺杂多孔碳的BET比表面积达到997 m²·g^-1,并使其微孔孔体积达到0.44 cm³·g^-1。得益于较高的比表面积以及其富含微孔的特性,当材料应用于二氧化碳吸附时,具有较高的CO₂吸附量,在273和298 K时分别高达5.13,3.22 mmol·g^-1,并具有良好的选择性。     

低成本硫掺杂多孔碳材料的制备及其超级电容性能

以廉价的胶态二氧化硅为模板,蔗糖为碳源,硫酸为预碳化试剂和硫源,通过硬模板法制备了相对廉价的硫掺杂多孔碳(SSC-T,T℃代表碳化温度)材料。采用多种表征方法对多孔碳材料的微观形貌、孔道结构、比表面积和表面硫物种进行了表征,探究了硫酸和碳化温度对多孔碳材料的微观形貌、孔道结构和比表面积的影响。结果表明,碳化温度对碳的孔结构、比表面积和硫元素的含量有显著的影响,其中900℃碳化得到的样品SSC-900具有最大的比表面积、孔体积和比电容,远高于未加入硫酸制备的碳材料SC-900,表明硫酸的加入可以提高碳材料的比表面积、孔体积,进而提高碳材料的比电容。与昂贵的有序介孔碳CMK-3相比,SSC-900具有成本更低、孔径更大和电容性能更好的优点。在以6.0 mol·L^-1 KOH为电解质的三电极体系中,在0.5 A·g^-1的电流密度下,SSC-900的比电容可以达到357 F·g^-1,而SC-900和CMK-3的比电容分别仅为152和266 F·g^-1。电容贡献分析表明,SSC-900的双层电容值和赝电容值均高于SC-900。此外,SSC-900在0.5 A·g^-1的电流密度下循环10 000次后仍能保持98.4%的初始比电容。     

基于羧甲基纤维素钠制备氮掺杂多孔炭及其电容性能研究

以羧甲基纤维素钠(NaCMC)为碳源, 利用直接炭化工艺(无需进一步活化)制备多孔炭材料; 然后, 以CO(NH₂)₂为氮源, 形成了氮掺杂多孔炭材料. 氮的存在形式包括吡啶N、石墨N和吡咯N. 实验结果表明, 羧甲基纤维素钠与CO(NH₂)₂之间的配比可以有效控制氮存在形式、含量、样品的比表面积及孔的结构等. 样品的电化学性能测试表明, 氮掺杂后多孔炭材料的超电容性能得到了显著提升. 以carbon-N-1:20为例, 其比表面积可达858 m²·g^-1, 远高于未经氮掺杂carbon-blank 的463 m²·g^-1, 其质量比电容则由94.0 F·g^-1提高到了156.7F·g^-1.     

低成本硫掺杂多孔碳材料的制备及其超级电容性能

以廉价的胶态二氧化硅为模板，蔗糖为碳源，硫酸为预碳化试剂和硫源，通过硬模板法制备了相对廉价的硫掺杂多孔碳(SSC-T，T℃代表碳化温度)材料。采用多种表征方法对多孔碳材料的微观形貌、孔道结构、比表面积和表面硫物种进行了表征，探究了硫酸和碳化温度对多孔碳材料的微观形貌、孔道结构和比表面积的影响。结果表明，碳化温度对碳的孔结构、比表面积和硫元素的含量有显著的影响，其中900℃碳化得到的样品SSC-900具有最大的比表面积、孔体积和比电容，远高于未加入硫酸制备的碳材料SC-900，表明硫酸的加入可以提高碳材料的比表面积、孔体积，进而提高碳材料的比电容。与昂贵的有序介孔碳CMK-3相比，SSC-900具有成本更低、孔径更大和电容性能更好的优点。在以6.0 mol·L^-1 KOH为电解质的三电极体系中，在0.5 A·g^-1的电流密度下，SSC-900的比电容可以达到357 F·g^-1，而SC-900和CMK-3的比电容分别仅为152和266 F·g^-1。电容贡献分析表明，SSC-900的双层电容值和赝电容值均高于SC-900。此外，SSC-900在0.5 A·g^-1的电流密度下循环10 000次后仍能保持98.4%的初始比电容。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。