Preparation of a Carbon-Coated SPME Fiber and Application to the Analysis of BTEX and Halocarbons in Water

A carbon-coated fiber for solid-phase microextraction (SPME) has been prepared from powdered activated carbon (PAC) and a fused-silica fiber. Scanning electron microscopy of the coating revealed the carbon particles were uniformly distributed on the surface of the fiber substrate. Efficient extraction of BTEX (benzene, toluene, ethylbenzene, p-xylene, and o-xylene) and halocarbons (chloroform, trichloroethylene, and carbon tetrachloride), with short extraction and desorption times, was achieved by use of the coated fiber. The maximum working temperature of the coated fiber was 300 °C and the lifetime was over 140 desorption operations at 260 °C. Limits of quantification (LOQ) of the SPME method for the eight analytes ranged from 0.01 to 0.94 μg L⁻¹, and relative standard deviations (RSD) were below 7.2% (n=6). Recoveries were 87.9–113.4% when the method was applied to the analysis of BTEX and the halocarbons in real aqueous samples. An erratum to this article is available at .     

Analysis of BTEX and chlorinated solvents in meconium by headspace-solid-phase microextraction gas chromatography coupled with mass spectrometry

Meconium is the earliest stool of newborns, and is a complex matrix that reflects the degree of exposure of the fetus to xenobiotics. To investigate fetal exposure to volatile organic compounds, an analytical method was developed to identify and quantify BTEX (benzene, toluene, ethylbenzene, and o,m,p-xylene) and two chlorinated solvents (trichloroethylene and tetrachloroethylene) in meconium. Headspace-solid-phase microextraction coupled with gas chromatography–mass spectrometry was selected because it is simple, sensitive, can be automated, and requires no extensive sample preparation. Several extraction variables were optimized (fiber type, incubation time, temperature of fiber, and use of salt). Because meconium is a complex matrix, quantification by SPME was considered carefully because of potential interference, for example competitive adsorption. Calibration in water was compared with calibration in meconium using external and internal methods (with isotope-labeled compounds). In meconium, limits of quantification were determined to be in the range 0.064–0.096 ng g^?1 for the investigated compounds. All target compounds were determined in “real-case” meconium samples.     

Preparation and characterization of metal-organic framework MIL-101(Cr)-coated solid-phase microextraction fiber

Metal-organic frameworks (MOFs) have received great attention as novel sorbents due to their fascinating structures and intriguing potential applications in various fields. In this work, a MIL-101(Cr)-coated solid-phase microextraction (SPME) fiber was fabricated by a simple direct coating method and applied to the determination of volatile compounds (BTEX, benzene, toluene, ethylbenzene, m-xylene and o-xylene) and semi-volatile compounds (PAHs, polycyclic aromatic hydrocarbons) from water samples. The extraction and desorption conditions of headspace SPME (HS-SPME) were optimized. Under the optimized conditions, the established methods exhibited excellent extraction performance. Good precision (<7.7%) and low detection limits (0.32–1.7 ng L⁻¹ and 0.12–2.1 ng L⁻¹ for BTEX and PAHs, respectively) were achieved. In addition, the MIL-101(Cr)-coated fiber possessed good thermal stability, and the fiber can be reused over 150 times. The fiber was successfully applied to the analysis of BTEX and PAHs in river water by coupling with gas chromatography–mass spectrometry (GC–MS). The analytes at low concentrations (1.7 and 10 ng L⁻¹) were detected, and the recoveries obtained with the spiked river water samples were in the range of 80.0–113% and 84.8–106% for BTEX and PAHs, respectively, which demonstrated the applicability of the self-made fiber.     

Liquid–Liquid Microextraction of Nitrophenols Using Supramolecular Solvent and Their Determination by HPLC with UV Detection

A novel, efficient, and environmentally friendly method—supramolecular solvent liquid–liquid microextraction (SMS-LLME) combined with high-performance liquid chromatography (HPLC)—was first established for the determination of p-nitrophenol and o-nitrophenol in water samples. Several important parameters influencing extraction efficiency, such as the type and volume of extraction solvent, pH of sample, temperature, salt effect, extraction time, and stirring rate, were optimized in detail. Under the optimal conditions, the enrichment factor was 166 for p-nitrophenol and 160 for o-nitrophenol, and the limits of detection by HPLC were 0.26 and 0.58 μg L^?1, respectively. Excellent linearity with coefficients of correlation from 0.9996 to 0.9997 was observed in the concentration range of 2–1,000 μg L^?1. The ranges of intra- and interday precision (n = 5) at 100 μg L^?1 of nitrophenols were 5.85–7.76 and 10.2–11.9 %, respectively. The SMS-LLME method was successfully applied for preconcentration of nitrophenols in environmental water samples.     

Preparation of an ionic liquid-mediated carbon nanotube-poly(dimethylsiloxane) fiber by sol–gel technique for determination of polycyclic aromatic hydrocarbons in urine samples using head-space solid-phase microextraction coupled with gas chromatography

A novel ‘ionic liquid-mediated multi-walled carbon nanotube (MWCNT)-poly(dimethylsiloxane) (PDMS)’ hybrid coating was prepared by the covalent functionalization of MWCNTs with hydroxyl-terminated PDMS using the sol–gel technique. The prepared fiber was successfully used for the separation and determination of trace amounts of polycyclic aromatic hydrocarbon compounds (PAHs) in four urine samples using head-space solid-phase microextraction coupled to gas chromatography-flame ionization detection. The proposed fiber has high thermal stability and long durability and it can be used more than 210 times without any significant change in its sorption properties. The effects of important parameters such as the exposure time, sampling temperature, sample ionic strength and stirring rate on the extraction efficiency have been studied and optimized. Under the optimal conditions, the method detection limits (S/N = 3) were in the range of 0.0005–0.004 ng mL^?1 and the limits of quantification (S/N = 10) between 0.002 and 0.01 ng mL^?1. The relative standard deviations for one fiber (repeatability, n = 5) were 4.9–7.5 % and for the fibers obtained from different batches (reproducibility, n = 3), 6.1–8.9 %. The developed method was successfully applied to determine trace levels of PAHs in real urine samples. The obtained relative recoveries for the spiked samples with 0.05 ng mL^?1 of each of the PAH compounds were 89.3–107.2 %.     

Solid-phase microextraction–gas chromatographic determination of volatile monoaromatic hydrocarbons in soil

Benzene, toluene, ethylbenzene, three isomers of xylene, and cumene have been isolated and enriched from soil samples by a combination of water extraction at room and elevated temperature and headspace–solid-phase microextraction before their gas chromatographic–mass spectrometric (GC–MS) determination. The conditions used for all stages of sample preparation and chromatographic analysis were optimized. Analytes sampled on a polydimethylsiloxane-coated solid-phase microextraction fiber were thermally desorbed in the split/splitless injector of a gas chromatograph (GC) coupled with a mass spectrometer (MS). The desorption temperature was optimized. The GC separation was performed in a capillary column. Detection limits were found to be of the order of ca. 1 ng g^–1. Relative recoveries of the analytes from soils were found to be highly dependent on soil organic-matter content and on compound identity; they ranged from ca 92 to 96% for sandy soil (extraction at room temperature) and from ca 27 to 55% for peaty soil (extraction at elevated temperature). A few real-world soil samples were analyzed; the individual monoaromatic hydrocarbon content ranged from below detection limits to 6.4 ng g^–1 for benzene and 8.1 for the total of p- + m-xylene.     

Analysis of gasoline contaminated water samples by means of dopant-assisted atmospheric pressure photoionization differential ion mobility spectrometry

In this study the influence of aromatic dopant benzene on the sensitivity of GC-APPI-DMS to gasoline related aromatic compounds was investigated. This influence was investigated on example of four gasolin related fingerprints (toluene, ethylbenzene, o-xylene, and 1,2,4-trimethylbenzene), which were found in high relative abundance in the water-soluble gasoline fraction. The analysis of calibration curves slopes demonstrats that the GC-APPI-DMS sensitivity to gasoline fingerprints can be improved by up to seven times when benzene concentration in nitrogen carrier gas is less than 10 ppm_v/v. The estimated detection limits (S/N?=?3) for the analyzed in this study compounds were found to be within the range of 33–105 μg L^?1 at benzene concentration in the carrier gas of 2.27 ppm_v/v (10 μL injection volume). These limits of detection may be reduced (at the cost of lower resolution) using the larger injection volumes. For example, increase of injection volume to 100 μL at benzene concentration in the carrier gas of 2.27 ppm_v/v leads to reduction of LOD values for toluene, ethylbenzene, and o-xylene to 11.1, 13.3, and 5.3 μg L^?1, respectively.     

A Hexagonally Ordered Nanoporous Silica-Based Fiber Coating for SPME of Polycyclic Aromatic Hydrocarbons from Water Followed by GC�CMS

A highly porous fiber coating material was prepared and functionalized with 3-amino propyl triethoxysilane (APTES) on hexagonally ordered nanoporous silica (SBA-15). Applicability of this coating was assessed employing a laboratory made solid-phase microextraction (SPME) device and gas chromatography?Cmass spectrometry for the simultaneous sampling and determination of trace polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions. A one at the time optimization strategy was applied to investigate and optimize important extraction parameters such as extraction temperature, extraction time, ionic strength and sonication time. In the optimum conditions, the relative standard deviations for deionized water, spiked with selected PAHs were between 3.3 and 7.7% (n = 3), and detection limits for the studied compounds were 4.2 and 26.1 pg mL^?1. No significant change was observed in the extraction efficiency of the new SPME fiber, over 50 extractions. The proposed method was successfully applied to the extraction and determination of PAHs in the waste water samples.     

Determination of Trace Amounts of Chlorogenic Acid and Three of Its Metabolites Using Time-Resolved LPME and LC-UV Detection in Biological Specimens

Chlorogenic acid (CGA) is an effective antitumor, anti-inflammatory and antimicrobial agent. Since the absorption and metabolism of CGA remains controversial, time-resolved binary-solvent synergy liquid-phase microextraction (TRBSS-LPME) using hollow fiber was developed for the extraction of CGA and its metabolites: caffeic acid, p-hydroxycinnamic acid and ferulic acid, from biological specimens. In this technique, the target drugs were extracted into a binary-solvent immobilized in the wall pores of hollow fiber. The extraction occurred due to a pH gradient between the two sides of the fiber. After extraction, an aliquot was analyzed by LC. Under the optimal conditions, the CGA, caffeic acid, p-hydroxycinnamic acid and ferulic acid had good correlation of determination values (R > 0.97) and the detection limits (LODs) were 1.0, 1.0, 2.0, and 5.0 ng mL^?1 in plasma; and 1.0, 50, 10, and 50 ng mL^?1 in urine. The mean recoveries in plasma were 90.8–119.8% for CGA and its metabolites: caffeic acid, p-hydroxycinnamic acid and ferulic acid evaluated and the mean recoveries of caffeic acid and p-hydroxycinnamic acid in urine were 81.6–111.6%. Finally, TRBSS-LPME was successfully used for the determination of target drugs in biological specimens. It not only extended the linear range of CGA determination in biological samples and improved the sensitivity, but also eliminated interferences from complex constituents in the biological specimens and reduced the LOD.     

Temperature-Induced Ionic Liquids Dispersive Liquid�CLiquid Microextraction of Tetracycline Antibiotics in Environmental Water Samples Assisted by Complexation

In this study, dispersive liquid?Cliquid microextraction (DLLME) combined with ultra high pressure liquid chromatography (UHPLC)?Ctunable ultraviolet detection (TUV), was developed for pre-concentration and determination of trace levels of tetracyclines, including 4-epitetracycline, 4-epichlortetracycline, doxycycline, chlortetracycline oxytetracycline, tetracycline, 4-epianhydrotetracycline and anhydrotetracycline, in aqueous samples. La (III) was used as the chelating agent to form a hydrophobic complex compound with tetracyclines, followed by extraction with ionic liquids. Some important parameters that may affect extraction efficiencies were examined and optimized. Under the optimum conditions, linearity of the method was observed in the range of 0.1?C200 ??g L^?1, with correlation coefficients (r ²) >0.992. The limits of detection and quantification were 0.031?C0.079 and 0.10?C0.26 ??g L^?1, respectively. The spiked recoveries of eight target compounds in river water, fishpond water and hog leachate were achieved in the range of 62.6?C96.3, 58.9?C94.5, 55.1?C86.1%, respectively.     

Determination of Phthalates in Beverages by Headspace SPME-GC Using Calix[6]arene Fiber

A headspace solid-phase microextraction, in conjunction with gas chromatography using a novel sol–gel calix[6]arene-contained fiber for the determination of phthalate acid esters in non-alcoholic beverages is described for the first time. A Taguchi’s L₂₅ (5⁶) orthogonal array experimental design was introduced to optimize the extraction parameters such as extraction temperature, extraction time, salt concentration and stirring speed. Under the optimized conditions, the method showed linear response of three to five orders of magnitude with correlation coefficients (r) better than 0.995. Owing to the good selectivity and high sensitivity of this fiber to phthalate acid esters, the extraction was carried out in real beverage matrix and low detection limits of 0.015–0.298 μg L^?1 were achieved. The recoveries of standard addition tests amounted to 87.9–108.3% and the relative standard deviation values varied from 9.62 to 15.2%. The method was applied to the analysis of 12 kinds of beverages and bis-2-ethylhexyl phthalate was the sole analyte detected in these samples.     

Solid-phase microextraction using a diglycidyloxycalix[4]arene coated fiber combined with gas chromatography: very simple, rapid and sensitive method for the determination of chlorobenzenes in water

A fiber material for solid-phase microextraction (SPME) was obtained by blending 5,11,17,23-tetra-tert-butyl-25,27-dihydroxy-26,28-diglycidyloxycalix[4]arene with hydroxy-terminated silicone oil by sol-gel technology. It was used for headspace SPME combined with gas chromatography using electron capture detection to determine seven chlorobenzenes in water matrix. Optimum extraction conditions were 15 min at 20 °C with a solution containing 300 g L^?1 sodium chloride. The fiber exhibits far higher extraction efficiency than the commercially available poly(dimethylsiloxane) (PDMS) and PDMS-divinylbenzene fibers. The detection limits range from 0.32 to 2.25 ng L^?1, and the relative standard deviations are <5%. The calibration curves display a high level of linearity, with correlation coefficients ranging between 0.9996 and 1. The method was applied to analyze a lake water sample that was found to be polluted with 1,2,3,4-tetrachlorobenzene and hexachlorobenzene. It was compared to the United States Environmental Protection Agency method and other recently introduced methods. The results demonstrate that the technique is rapid, simple, and sensitive, and thus represents an attractive alternative for ultra-trace analysis of chlorobenzenes in water samples.     

Hollow fiber membrane supported thin liquid film extraction for determination of trace phenoxy acid herbicides and phenols in environmental water samples

Traces of phenoxy acid herbicides and phenols were determined in environmental water samples by high performance liquid chromatography (HPLC) coupled to thin liquid film extraction (TLFE). A TLFE sampling device was prepared by dipping pieces of a polypropylene microporous hollow fiber membrane into dihexyl ether (containing 10% tri-n-octylphosphine oxide as carrier) for a few minutes to impregnate the pores of the hollow fiber wall. Extraction of analytes takes place from the outer aqueous phase into the immobilized solvent. After extraction the removal of the organic solvent was accomplished with a few µl of methanol which was used for HPLC analysis. Enrichment factors as high as 446 were obtained for the target compounds. The method provided detection limits as low as 0.4–1.2 µg L^?1, good repeatability (the RSD ranging from 2.1 to 6.3%, n?=?5) and a linear range from 2 to 200 µg L^?1 for the target compounds. Real sample analysis showed recoveries between 84.6% and 112% for all compounds investigated.     

Application of Sol–Gel Based Poly(ethylene glycol)/Multiwalled Carbon Nanotubes Coated Fiber for SPME of Methyl tert-Butyl Ether in Environmental Water Samples

In this research, the sol–gel technology was applied for the preparation of solid-phase microextraction fibers for extracting of methyl tert-butyl ether (MTBE) from environmental water samples. For this purpose, two different polymers such as poly(ethylene glycol) (PEG) and combination of PEG and multiwall carbon nanotubes (MWCNTs) were prepared using sol–gel technology as coating procedure for the fibers. The pre-concentration process followed by GC–FID determination was used and the results evidenced that pre-concentration factor for PEG/CNTs fiber was approximately five times higher than PEG. Parameters affecting the extraction efficiency such as temperature, extraction time, stirring speed and salt effect for each fiber were investigated and optimized. On the optimal conditions, the linear range for MTBE with PEG and PEG/CNT fibers were 10–3,000 and 1–1,000 ng mL^?1 and the detection limits (S/N = 3) were 1.0 and 0.3 ng mL^?1, respectively. The sol–gel PEG/CNTs fiber has good performance and therefore relatively better figures of merit and experimental results such as thermal stability (up to 320 °C), average of life time (over 150 times) and repeatability (RSD < 4) in comparison to conventional PDMS/Carboxen fiber, which was already reported for determination of MTBE.     

Synthesis and Application of High Selective Monolithic Fibers Based on Molecularly Imprinted Polymer for SPME of Trace Methamphetamine

A monolithic solid-phase microextraction (SPME) fiber was fabricated based on a molecularly imprinted polymer which could be coupled with gas chromatography for extraction, pre-concentration and determination of methamphetamine (MAMP). Methacrylic acid, ethylene glycol dimethacrylate and MAMP play the roles of functional monomer, cross-linker and template, respectively. The effective factors influencing the polymerization and extraction procedures were investigated and will be detailed here. The fabricated fiber was firm, inexpensive, stable, selective and durable which gives it vital importance in SPME. Selectivity of the fabricated fiber in relation to the template in solution containing MAMP, related and unrelated compounds was also investigated. Under the optimum conditions, the calibration plot was linear in the range of 50?C3,500 ng mL^?1 (r ²  = 0.997). The high extraction efficiency was obtained for MAMP giving a detection limit of 14 ng mL^?1. The fabricated fiber was successfully applied to SPME of MAMP from human saliva samples followed by gas chromatography-flame ionization detector analysis.     

Improvement of HS-SPME for analysis of volatile organic compounds (VOC) in water samples by simultaneous direct fiber cooling and freezing of analyte solution

The sensitivity and precision of headspace solid-phase micro extraction (HS-SPME) at an analyte solution temperature (T _as) of +35 °C and a fiber temperature (T _fiber) of +5 °C were compared with those for HS-SPME at T _as and T _fiber of −20 °C for analysis of the volatile organic compounds benzene, 1,1,1-trichloroethane, trichloroethylene, toluene, o-xylene, ethylbenzene, m/p-xylene, and tetrachloroethylene in water samples. The effect of simultaneous fiber cooling and analyte solution freezing during extraction was studied. The compounds are of different hydrophobicity, with octanol/water partition coefficients (Kow) ranging from 126 and 2511. During a first set of experiments the polydimethylsiloxane (PDMS) SPME fiber was cooled to +5 °C with simultaneous heating of the aqueous analyte solution to +35 °C. During a second set of experiments, both SPME fiber holder and samples were placed in a deep freezer maintained at −20 °C for a total extraction time of 30 min. After approximately 2 min the analyte solution in the vial began to freeze from the side inwards and from the bottom upwards. After approximately 30 min the solution was completely frozen. Analysis of VOC was performed by coupling HS-SPME to gas chromatography-mass spectrometry (GC-MS). In general, i.e. except for tetrachloroethylene, the sensitivity of HS-SPME increased with increasing compound hydrophobicity at both analyte solution and fiber temperatures. At T _as of +35 °C and T _fiber of +5 °C detection limits of HS-SPME were 0.5 μg L⁻¹ for benzene, 1,1,1-trichloroethane, trichloroethylene, and tetrachloroethylene, 0.125 μg L⁻¹ for toluene, and 0.025 μg L⁻¹ for ethylbenzene, m/p-xylene, and o-xylene. In the experiments with T _as and T _fiber of −20 °C, detection limits were reduced for compounds of low hydrophobicity (Kow<501), for example benzene, toluene, 1,1,1-trichloroethane, and trichloroethylene. In the concentration range 0.5–62.5 μg L⁻¹, the sensitivity of HS-SPME was enhanced by a factor of approximately two for all compounds by performing the extraction at −20 °C. A possible explanation is that freezing of the water sample results in higher concentration of the target compounds in the residual liquid phase and gas phase (freezing-out), combined with enhanced adsorption of the compounds by the cooled fiber. The precision of HS-SPME, expressed as the relative standard deviation and the linearity of the regression lines, is increased for more hydrophobic compounds (Kow>501) by simultaneous direct fiber cooling and freezing of analyte solution. Background contamination during analysis is reduced significantly by avoiding the use of organic solvents.     

Simultaneous Determination of Deltamethrin and Permethrin in Water Samples Using Homogeneous Liquid–Liquid Microextraction via Flotation Assistance and GC-FID

A new method was developed for the simultaneous determination of deltamethrin and permethrin in water samples with homogeneous liquid–liquid microextraction via flotation assistance and gas chromatography–flame ionization detection. A special extraction cell was designed to facilitate collection of the low density solvent extracts. The sample solution was added into the extraction cell, which contained an appropriate mixture of n-hexane (as an extraction solvent) and acetone (as a homogeneous solvent). Air flotation allowed the extraction solvent to be collected from the top of the solution. Under the optimum conditions, good linearity was observed in the range of 1.0–200 μg L^?1 with a correlation coefficient (r ²) greater than 0.9980 for both of the analytes. The limits of detection were 0.2 and 0.3 μg L^?1 for deltamethrin and permethrin, respectively (S/N = 3). The developed method was successfully applied to determine the two pesticides in three different water samples.     

Fast Analysis of Synthetic Pyrethroid Metabolites in Water Samples Using In-Syringe Derivatization Coupled Hollow Fiber Mediated Liquid Phase Microextraction with GC-ECD

A fast and efficient method has been demonstrated for the trace determination of six important metabolites of synthetic pyrethroids including cis- and trans-3-(2,2-dichlorovinyl)-2,2-dimethylcyclopropane-1-carboxylic acid (cis- and trans-Cl₂CA), cis-3-(2,2-dibromovinyl)-2,2-dimethylcyclopropane-1-carboxylic acid (cis-Br₂CA), 4-fluoro-3-phenoxybenzoic acid (4-F-3-PBA), 3-phenoxybenzoic acid (3-PBA), and 2-phenoxybenzoic acid (2-PBA) in environmental water samples using hollow fiber (HF)-mediated liquid-phase microextraction (LPME) coupled with in-syringe derivatization (ISD) followed by gas chromatography (GC) with electron capture detector (ECD) analysis. This method utilizes a HF membrane segment impregnated with extraction solvent as the LPME sampling probe, which was connected to a microsyringe pre-filled with derivatizing agents, and it was immersed into sample solution for extraction. After extraction, the extracting solution was subjected to derivatization reaction that was performed inside the syringe barrel followed by GC-ECD analysis. Under optimal conditions, the best extraction efficiency was obtained using sampling probe (2.0 cm hollow fiber) impregnated with 1-octanol immersed into water sample (5.0 mL, adjusted pH below 1.0) and stirring (1,250 rpm) for 10 min at 70 °C and diisopropylcarbodiimide (2 μL) and 1,1,1,3,3,3-hexafluoro-2-propanol (1 μL) were the derivatizing agents used. The detection limits of 3 ng mL^?1 for cis- and trans-Cl₂CA, 2 ng mL^?1 for cis-Br₂CA, 6 ng mL^?1 for 4-F-3-PBA, and 0.6 ng mL^?1 for 3-PBA and 2-PBA. The method showed good linearity (R ² = 0.973?0.998), repeatability from 4.0 to 13 % (n = 5), recovery from 79.2 to 95.7 %, and enrichment factors ranged between 109 and 159 for target analytes spiked in water samples. The proposed method and conventional methods were compared. Results suggested that the proposed HF-LPME-ISD/GC-ECD method was a rapid, simple, inexpensive, and eco-friendly technique for the analysis of metabolites of pyrethroids.     

Radiochemical studies relevant to the separation of 68Ga and 68Ge

The radiochemical separation of radiogallium from radiogermanium was studied using ion-exchange chromatography (Amberlite IR-120) and solvent extraction (Aliquat 336 in o-xylene). Both Amberlite IR-120 and Aliquat 336 in o-xylene have been used for the first time in separations involving radiogallium and radiogermanium. For tracer studies the radionuclides ⁶⁸Ge (t _1/2 = 270.8 days), ⁶⁹Ge (t _1/2 = 39 h) and ⁶⁷Ga (t _1/2 = 78.3 h) were used. They were produced by the nuclear reactions ^natGa(p,xn)^68,69Ge and ^natZn(p,xn)⁶⁷Ga, respectively, and separated from their target materials in no-carrier-added form. Several factors affecting the separation of radiogallium from radiogermanium were studied and for each procedure the optimum conditions were determined. The solvent extraction using Aliquat 336 was found to be better. The separation yield of radiogallium was >95%, the time of separation short, the contamination from radiogermanium <0.008% and the final product was obtained in 0.5 M KOH. This method was adapted to the separation of n.c.a. ⁶⁸Ga from its parent n.c.a. ⁶⁸Ge. The quality of the product thus obtained is discussed.     

Domoic acid at trace levels in lagoon waters: assessment of a method using internal standard quantification

Domoic acid (DA) is a neurotoxin produced by different algae, including pennate diatoms, principally from the genus Pseudo-nitzschia, and it is the main cause of amnesic shellfish poisoning. Determination of this toxin in seawater samples is fundamental to define the real contamination risks for aquatic species. We have developed two very sensitive instrumental methods using hydrophilic interaction liquid chromatography coupled using tandem mass spectrometry in positive and negative polarity modes. Instrumental detection limits were 9 pg mL^?1 for positive and 19 pg mL^?1 for negative ionisation. A procedural method based on solid-phase extraction for the determination of dissolved DA present in seawater has been developed, and an extraction procedure was employed for the determination of the toxin in the particulate fraction. DA quantification was performed using the internal standard method to account for signals fluctuations and random errors during sample treatment. To our knowledge, this is the first study to use this quantification method for DA determination. Trueness, extraction yield, matrix effects, repeatability and procedural detection limits were evaluated during method validation. Procedural detection limits of 0.3 pg mL^?1 (positive mode) and 0.6 pg mL^?1 (negative mode) were found for the dissolved fraction, and absolute limits of 0.4 pg (positive mode) and 6.0 pg (negative mode) for particulate samples were obtained. The most sensitive method in positive mode was applied to define DA occurrence in the Venice Lagoon. Trace concentrations of domoic acid ranging from 1.5 to 16.2 pg mL^?1 were found for the first time in the Venetian environment.