Preparative synthesis of isoprene oxide

The reaction of isoprene, hydrogen peroxide, and commercial hydrobromic acid gives 1-bromo-2-methyl-3-buten-2-ol, the low-temperature dehydrobromination of which gives isoprene oxide in high yield.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 6, pp. 736–737, June, 1989.     

钛硅分子筛催化1-丁烯环氧化反应溶剂效应和酸碱效应研究

研究了用双氧水为氧化剂，钛硅分子筛TS-1催化1-丁烯环氧化反应的溶剂效应．研究发现，在质子性溶剂中1-丁烯环氧化反应活性高于非质子性溶剂，而以甲醇为溶剂H2O2转化率最高．分别利用碱性添加物稀氨水溶液和酸性添加物稀盐酸溶液调变反应介质的pH值，考察了介质的pH值对1-丁烯环氧化反应的影响，结果表明，随pH值提高，1，2-环氧丁烷(B0)的选择性略提高，但是过量稀氨水的加入会导致催化剂失活，双氧水的转化率及利用率明显下降．与钛硅分子筛催化丙烯环氧化相比，酸性添加物的加入对反应结果的影响不大，随反应介质的pH值降低1，2-环氧丁烷的选择性没有明显下降．     

不同TS-1分子筛含量条状催化剂的丙烯环氧化性能

环氧丙烷(PO)是重要的有机化工原料，主要用于生产聚醚多元醇、丙二醇及其它化工产品。现在工业上主要采用氯醇法和Halcon法生产环氧丙烷，但分别存在污染和联产物量大等问题，人们在改进原有工艺的同时，致力于寻找流程短、副产少、无污染的新工艺。TS-1分子筛的成功合成^[1]及其在以     

DIASTEREOSELECTIVE SYNTHESIS AND STEREOCHEMISTRY OF (Z)-1-[3-ARYL-2-(PHENYLSULFANYL)-2-OXIRANYL]-1-ETHANONES

Diastereoselective synthesis of a series of (Z)-1-[3-aryl-2-(phenylsulfanyl)-2-oxiranyl]-1-ethanones was effected from the reaction of (Z)-4-aryl-3-(phenylsulfanyl)-3-buten-2-ones with alkaline hydrogen peroxide in tetrahydrofuran. The stereochemistry of the oxiranes has been deduced from two-dimensional NOESY spectrum.     

两亲性TS-1沸石的制备及其相界面催化反应性能的研究

采用三甲基氯硅烷和正十八烷基三氯硅烷对TS-1沸石样品进行表面修饰，制备出了两亲性含钛沸石样品．这类两亲性含钛沸石能分布于水、油两相界面处．改性后样品的骨架未遭破坏，其中钛仍然保持了四配位骨架钛的状态，但其晶貌发生了某些改变．这类两亲性样品在不加共溶剂及静置的反应条件下，对1-辛烯和双氧水的相界面环氧化催化反应表现出优良的催化活性．尤其是三甲基氯硅烷改性后的TS-1沸石，在相界面催化反应中，具有比改性前高得多的活性．我们还发现，在该相界面催化反应条件中，相界面的面积和催化剂用量是两个最重要的影响因素，当相界面面积(cm^2)与催化剂用量(mg)的比例控制在0．15左右时，两亲性TS-1沸石的催化活性达到最高值．     

Solvent effect on epoxidation of allyl chloride with hydrogen peroxide on titanium-containing silicalite

The solvent effect on liquid-phase epoxidation of allyl chloride with an aqueous solution of hydrogen peroxide on TS-1 titanium-containing silicalite was examined. 1-Butanol, 2-butanol, 1-propanol, isopropanol, methanol, ethanol, water, acetone, methyl ethyl ketone, and 1-pentanol were tested as solvents.     

TS-1/H2O2催化模拟汽油中噻吩的选择氧化研究

随着环境法规的日益严格,世界各国对于燃料中硫质量分数做了新的规定,要求车用燃料的硫控制在10×10-6~50×10-6,燃料电池硫的质量分数控制为(1×10-6。要达到这样高的脱硫深度,传统的脱硫方法面临着极大的挑战[1]。因此,其他非HDS脱硫方法受到研究者关注,其中氧化萃取深度脱硫     

Synthesis of acetone oxime through acetone ammoximation over TS-1

The ammoximation of acetone to acetone oxime with 30 wt.% hydrogen peroxide over TS-1 has been studied. The conversion of acetone and the selectivity to acetone oxime can reach 99% and 94%, respectively. The by-products are the corresponding hydrazone, imine and small amounts of unidentified compounds. The influence of various parameters such as solvent, temperature, amounts of catalyst and the NH₃ to acetone molar ratio were investigated. This revised version was published online in August 2006 with corrections to the Cover Date.     

硅胶微球负载钛硅分子筛TS-1催化剂的制备及对苯氧化合成苯酚的催化性能

将硅胶微球浸渍于钛硅分子筛（TS-1）合成液中,经晶化、焙烧制得负载TS-1分子筛硅胶微球催化剂。 用XRD、IR和SEM测试技术对其进行表征,将其用于过氧化氢氧化苯合成苯酚的反应中。 结果显示,TS-1分子筛能够很好地负载于硅胶表面,晶化温度160 ℃,晶化时间72 h,焙烧温度550 ℃,焙烧时间6 h时,获得的催化剂显示良好的催化性能。 在苯和H2O2初始原料量分别为0.5和0.1 mol、催化剂加入量为8 g、反应温度为60 ℃条件下,经过3 h的反应,苯的转化率达到10.32%,苯酚选择性达到97.12%。 9次重复使用后的苯转化率为9.42%,苯酚选择性为93.14%。     

The Heck synthesis of β-arylated ketones catalyzed by palladium immobilized on functional polysiloxane microspheres

Palladium catalysts, obtained by the impregnation of Pd(OAc)₂ on aminopropyl- or pyridine-functionalized polysiloxane microspheres, were used in the Heck reaction of iodobenzene with 3-buten-2-one and 3-buten-2-ol at 120°C using an oil bath or microwave heating. The synthesis of 4-phenyl-3-buten-2-one was one-step arylation of ketone while 4-phenyl-2-butanone was formed in two-step arylation–isomerization sequential transformation of alcohol. A very low palladium loading, 0.05 mol%, was sufficient to obtain a yield of ketones higher than 90%. In recycling experiments, an effect of the functional group present in polysiloxane was observed and much better results were obtained for the aminopropyl-modified polymer. The catalyst was easily retrieved and reused in eight consecutive runs in the reaction of 3-buten-2-one, while with 3-buten-2-ol 11 subsequent cycles were performed with practically the same yield.     

Hydroxylation of phenol with hydrogen peroxide in protic and aprotic solvents on TS-1 catalyst

Hydroxylation of phenol with a 25% aqueous solution of hydrogen peroxide in polar protic and aprotic solvents on TS-1 heterogeneous catalyst under various conditions was studied. The major reaction products (hydroquinone, pyrocatechol) and their ratio were determined. A kinetic model describing the hydroxylation in accordance with the Rideal-Eley mechanism was chosen.     

钛硅分子筛催化1-丁烯环氧化研究

自1983年Taramasso等报导TS-1的合成以来,钛硅分子筛的合成及应用一直是分子筛催化领域的热点。经典TS-1合成方法采用四丙基氢氧化铵（TPAOH）为模板剂,合成成本较高、条件苛刻,限制了其应用。用四丙基溴化铵（TPABr）为模板剂代替TPAOH,能够成功地合成TS-1。不同孔道结构的钛硅分子筛,如Ti-β、Ti-MCM-41、Ti-HMS等弥补了TS-1较小孔径的缺点,进一步扩大了钛硅分子筛的应用。本文以不同合成方法得到的TS-1及中孔Ti—HMS为催化剂,双氧水为氧化剂,1-丁烯环氧化合成1,2-环氧丁烷,研究了不同钛硅分子筛对1-丁烯环氧化反应的催化性能。     

Rate constants for the gas-phase reactions of Ozone with unsaturated Aliphatic Alcohols

The gas-phase reaction of ozone with unsaturated alcohols in air has been investigated at atmospheric pressure and ambient temperature (288–291 K). Cyclohexane was added to scavenge the hydroxyl radical which forms as a product of the ozone–unsaturated alcohol reaction. The reaction rate constants, in units of 10^?18 cm³ molecule^?1 s^?1, are 16.2 ± 0.7 for (±) 3-buten-2-ol, 17.9 ± 1.8 for 1-penten-3-ol, 10.0 ± 0.3 for 2-methyl-3-buten-2-ol, 169 ± 25 for cis-2 penten-1-ol, and 251 ± 41 for 2-buten-1-ol (mixture of isomers). Substituent effects on reactivity are discussed. The reactivity of unsaturated alcohols towards ozone is similar to that of their alkene structural homologues. Implications of these results with respect to the atmospheric persistence of unsaturated alcohols are briefly discussed. © 1994 John Wiley & Sons, Inc.     

TS-1催化丙烯环氧化过程中环氧丙烷的开环反应研究

环氧丙烷的开环反应是TS-1催化丙烯环氧化制备环氧丙烷过程的副反应,本文对醇溶剂中开环反应进行了研究,分析了该反应的酸性催化机理,酸性主要来自TS-1与H2O2的相互作用产生的质子酸,醇溶剂能显著增强体系酸性从而加快环氧丙烷的开环反应速度。三种醇按酸性增强程度的顺序为甲醇>异丙醇>仲丁醇。根据反应的Eley-Rideal 机理（吸附态的PO与游离态的醇发生开环反应,表面反应为控制步骤）再考虑各组分在TS-1上的吸附特点提出反应的机理模型。用实验数据进行了回归,得到了令人满意的动力学方程式,实验数据与模型计算值平均偏差小于10％。     

A rationale of the Baeyer-Villiger oxidation of cyclohexanone to ε-caprolactone with hydrogen peroxide: unprecedented evidence for a radical mechanism controlling reactivity

We demonstrate, for the first time, in the Baeyer-Villiger oxidation of cyclohexanone with aqueous hydrogen peroxide under conditions aimed at obtaining ε-caprolactone, that a thermally activated radical reaction leads to the concurrent formation of adipic acid, even when a stoichiometric amount of the oxidant is used. In fact, ε-caprolactone is the primary reaction product, but it is more reactive than cyclohexanone, and quickly undergoes consecutive transformations. When titanium silicalite-1 (TS-1) is used as a catalyst, the high concentration of hydroxy radicals within its pores accelerates the reaction rates, and the consecutive formation of adipic acid (and of lighter diacids as well) becomes largely kinetically preferred. The proper choice of the solvent, which also may act as a radical scavenger, both without catalyst and with TS-1, is a powerful tool for controlling the rates of the various reactions involved.     

Kinetic scheme of homogeneous acid-catalyzed transformation of isopentenols

The reactions occurring in an equilibrium mixture of 3-methyl-1-buten-3-ol and 3-methyl-2-buten-1-ol in 24–49 % aqueous solutions of H₂SO₄ yield isoprene, 3-methyl-3-buten-1-ol, isobutylene, formaldehyde, 3-methylbutane-1,3-diol. Isobutylene is rapidly hydrated to give 2-methylpropan-2-ol. The presence of formaldehyde in the reaction mixture indicates that the transformations involve the reverse Prins reaction. On the basis of experimental and literature data, two most probable reaction schemes were suggested.Translated fromIzvestiya Akademii Nauk. Sertya Khimicheskaya, No. 5, pp. 867–870, May, 1995.     

(E)- and (Z)-1-benzenesulfonyl-4-trimethylsilyl-2-butenes as (E)-1-(1,3-butadienyl) synthons

(E)- and (Z)-1-benzenesulfonyl-4-trimethylsilyl-2-butenes (E/Z=9), prepared from 4-trimethylsilyl-1-buten-3-ol, $\text{n}$-butyllithium and benzenesulfenyl chloride and oxidation of the intermediate (E)- and (Z)-1-benzenesulfinyl-4-trimethylsilyl-2-butenes with hydrogen peroxide, react with $\text{n}$-butyllithium and then primary halides to give 4-benzenesulfonyl-1-trimethylsilyl-2-alkenes which are rapidly 1,4-debenzenesulfonyltrimethylsilated to (E)-1,3-alkadienes by tetra-$\text{n}$-butylammonium fluoride at O°C.     

大晶粒钛硅沸石TS-1晶貌的离子蚀刻改性

钛硅沸石 TS- 1 [1] 的微孔体系由同是十元氧环的直通道和“Z”字形通道相交而成 ,孔径 0 .5 1～ 0 .5 6nm,晶体结构与硅铝 ZSM- 5沸石的 MFI结构相同 .TS- 1能以稀双氧水为氧源 ,使烃类发生选择氧化 ,生成含氧化合物 [2～ 8] .并已在催化苯酚羟基化和环己酮氨氧化方面实现了工     

TS-1分子筛催化双氧水氧化环己烷(英文)

系统地研究了ＴＳ－１分子筛催化双氧水氧化环己烷的反应。制备了三种ＴＳ－１分子筛,它们具有窄的粒径分布,在６０℃表现出高的活性和选择性。考察了溶剂、催化剂、反应温度、反应时间、ＴＳ－１中Ｔｉ含量及Ｈ２Ｏ７用量对氧化反应的影响。对具有完好晶型的ＴＳ－１分子筛役有必要进行预处理。最佳反应温度为８０～１１０℃,丙酮为最佳溶剂。环己酮的选择性与ＴＳ－１粒子大小有关,而Ｈ２Ｏ２选择性与ＴＳ－１用量无关。实验结果显示．溶剂在反应中间体的形成中起重要作用,Ｔｉ与丙酮配体的过氧配合物具有活化环己烷的活性。关键词 ＴＳ－１ 环己烷 催化氧化 Ｈ２Ｏ２     

Kinetics and mechanism of hydration of 3-methyl-3-buten-1-ol in aqueous solutions of sulfuric acid

Conclusions The kinetic regularities of hydration of 3-methyl-3-buten-1-ol in 9.6 to 34% aqueous solutions of sulfuric acid at 25°C were studied. An equation was found for describing the influence of the medium on the value of the effective rate constant of hydration of 3-methyl-3-buten-1-ol.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 5, pp. 1016–1019, May, 1988.