Novel flame‐retardant thermosets: Diglycidyl ether of bisphenol A as a curing agent of boron‐containing phenolic resins

Boron‐containing novolac resins were synthesized by the modification of a commercial novolac resin with different contents of bis(benzo‐1,3,2‐dioxaborolanyl)oxide. These novolac resins were crosslinked with diglycidyl ether of bisphenol A (DGEBA), and their thermal, thermodynamomechanical, and flame‐retardant properties were evaluated. The boron‐containing novolac resins were less thermally stable than the unmodified novolac resin. Their modification degree and DGEBA content were related to the crosslinking density of the materials. The boron‐containing novolac resins generated boric acid at high temperatures and gave an intumescent char that slowed down the degradation and prevented it from being total. They also showed good flame‐retardant properties. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1701–1710, 2006     

Preparation and properties of modified bismaleimide resins by novel bismaleimide containing 1,3,4‐oxadiazole

Bismaleimide (BMI) resin is a high‐performance thermosetting polymer, but its inherent brittleness hinder a broader range of application. Therefore, it has aroused wide concern to improve the toughness of BMI resins without scarification of their thermal stability. This paper reported some studies on modified BMI resins based on diallyl bisphenol A, novel BMI monomers, e.g. 2‐[3‐(4‐maleimidophenoxy)phenyl]‐5‐(4‐maleimidophenyl)‐1,3,4‐oxadiazole (m‐Mioxd) or 2‐[4‐(4‐maleimidophenoxy)phenyl]‐5‐(4‐maleimidophenyl)‐1,3,4‐ oxadiazole (p‐Mioxd) in different proportions (0.87:1, 1:1, 1.2:1; mol/mol). The curing mechanism and kinetics of the copolymerized systems were investigated by differential scanning calorimetry and Fourier transform infrared spectroscopy. Thermogravimetric analysis was applied to study the thermal properties of the cured resins, and the results indicated that the modified resins had excellent thermal stability with high residual weight percentage at 700°C (>50%), temperatures for 5% weight loss around 400°C. Besides, N,N′‐4,4′‐bismaleimidodiphenylmethylene and O,O′‐diallyl bisphenol A resin blends were modified by m‐Mioxd and p‐Mioxd, respectively. We investigated the effects of mole concentration of m‐Mioxd or p‐Mioxd on the curing process, mechanical properties, fracture toughness, and heat resistance of the modified resins. The results revealed that the introduction of m‐Mioxd and p‐Mioxd could improve the impact property of the modified BMI resins. When their proportion was 0.07, the impact strength increased 123.8% and 108.3%, respectively. The novel chain‐extended BMIs could reduce the crosslink density of cured resins and improve the brittleness effectively. Copyright © 2015 John Wiley & Sons, Ltd.     

Use of allyl, 2-tetrahydrofuryl, and 2-tetrahydropyranyl ethers as useful C3-, C4-, and C5-carbon sources: palladium-catalyzed allylation of aldehydes

Palladium-diethylzinc or palladium-triethylborane catalytically promotes self-allylation of 2-(allyloxy)tetrahydrofurans, 2-(allyloxy)tetrahydropyrans, and their hydroxy derivatives on the rings (ribose, glucose, mannose, deoxyribose, deoxyglucose). All the reactions proceed at room temperature and provide polyhydroxyl products, sharing a structural motif of a homoallyl alcohol, in good to excellent yields with high levels of stereoselectivity. Useful C3-unit elongation, which makes the best use of an allyl ether as a protecting group and a nucleophilic allylation agent, is demonstrated. Mechanisms for the umpolung reaction (of an allyl ether into an allylic anion) and stereoselectivity associated with allylation of aldehydes are discussed.     

Highly efficient iron‐catalyzed allylation of aromatic aldehydes with allyltriethoxysilane: one‐pot and practical synthesis of homoallyl ethers

FeCl₃ was found to be an active catalyst for the one‐pot allylation reaction of aromatic aldehydes with allyltriethoxysilane under mild and simple conditions, which resulted in the direct synthesis of homoallyl ethers with very high chemoselectivity and yields. Various types of homoallyl ethers were obtained in excellent yields (up to 99%). Copyright © 2008 John Wiley & Sons, Ltd.     

Scope of the allylation reaction with [RuCp(PP)]+ catalysts: changing the nucleophile or allylic alcohol

The scope of the dehydrative allylation reaction using allyl alcohol as allyl donor with [RuCp(PP)]⁺ complexes as catalysts is explored. Aliphatic alcohols are successfully allylated with allyl alcohol or diallyl ether, obtaining high selectivity for the alkyl allyl ether. The reactivity of aliphatic alcohols is in the order of primary > secondary ? tertiary. The tertiary alcohol 1‐adamantanol reacts extremely slowly in the absence of strong acid, but when HOTs is added, reasonable yields of 1‐adamantyl allyl ether are obtained. The alkyl allyl ether is found to be the thermodynamically favored product over diallyl ether. Apart from alcohols, thiols and indole are also efficiently allylated, while aniline acts as a catalyst inhibitor. Allylation reactions with various substituted allylic alcohols give products with retention of the substitution pattern. It is proposed that a Ru(IV) σ‐allyl species plays a key role in the mechanism of these allylation reactions. Copyright © 2010 John Wiley & Sons, Ltd.     

Synthesis and properties of a bisphenol A based phthalonitrile resin

A multiple aromatic ether linked phthalonitrile was synthesized and characterized. The oligomeric phthalonitrile monomer was prepared from the reaction of an excess amount of bisphenol A with 4,4′‐difluorobenzophenone in the presence of K₂CO₃ as the base in an N,N‐dimethylformamide/toluene solvent mixture, followed by end capping with 4‐nitrophthalonitrile in a two‐step, one‐pot reaction. The monomer properties were compared to those of the known resin 2,2‐bis[4‐(3,4‐dicyanophenoxy)phenyl]propane after being cured in the presence of bis[4‐(4‐aminophenoxy)phenyl]sulfone. Rheometric measurements and thermogravimetric analysis showed that the oligomeric phthalonitrile resin maintained good structural integrity upon heating to elevated temperatures and exhibited excellent thermal properties along with long‐term oxidative stability. The ether‐linked phthalonitrile resin absorbed less than 2.5% water by weight after exposure to an aqueous environment for extended periods. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4136–4143, 2005     

Palladium‐Catalyzed Substitution of Allylic Fluorides

As unusual substrates for the Tsuji–Trost allylation reaction, allylic fluorides are responsive to palladium‐catalyzed substitution. Their activity towards this reaction fits in the series OCO₂Me>OBz? F ?OAc. The classic stereoretention mechanism that involves sequential inversions does not operate in this case. Several distinct cases are considered.

     

Development and validation of an LC‐MS/MS method for simultaneous quantitative analysis of free and conjugated bisphenol A in human urine

Bisphenol A (BPA) is an environmental endocrine‐disrupting chemicals that is widely used in common consumer products. There is an increasing concern regarding human exposure to BPA owing to the potential adverse effects associated with its estrogenic activity. For assessing environmental exposure to BPA, it is essential to have a sensitive, accurate and selective analytical method, especially one that can detect low BPA levels in complex sample matrices. In this study, we developed and validated an accurate, sensitive, and robust liquid chromatography–tandem mass spectrometry method for simultaneous quantification of free BPA and BPA β‐d ‐glucuronide (BPA‐gluc) concentrations in human urine with only a single injection. Calibration curves were linear over a concentration range of 1–100 ng/mL for BPA and 10–1000 ng/mL for BPA‐gluc. The levels of the analytes were determined quantitatively with HPLC/ESI‐MS/MS by using negative electrospray ionization in the select ion monitoring mode and a pentaflouraphenyl propyl column. The validated method was applied to the analysis of spot urine specimens collected from randomly selected healthy human subjects. Copyright © 2013 John Wiley & Sons, Ltd.     

Selective extraction of bisphenol A from water by one‐monomer molecularly imprinted magnetic nanoparticles

One‐monomer molecularly imprinted magnetic nanoparticles were prepared as adsorbents for selective extraction of bisphenol A from water in this study. A single bi‐functional monomer was adopted for preparation of the molecularly imprinted polymer, avoiding the tedious trial‐and‐error optimizations as traditional strategy. Moreover, bisphenol F was used as the dummy template for bisphenol A to avoid the interference from residual template molecules. These nanoparticles showed not only large adsorption capacity and good selectivity to the bisphenol A but also outstanding magnetic response performance. Furthermore, they were successfully used as magnetic solid‐phase extraction adsorbents of bisphenol A from various water samples, including tap water, river water, and seawater. The developed method was found to be much more efficient, convenient, and economical for selective extraction of bisphenol A compared with the traditional solid‐phase extraction. Separation of these nanoparticles can be easily achieved with an external magnetic field, and the optimized adsorption time was only 15 min. The recoveries of bisphenol A in different water samples ranged from 85.38 to 93.75%, with relative standard deviation lower than 7.47%. These results showed that one‐monomer molecularly imprinted magnetic nanoparticles had the potential to be popular adsorbents for selective extraction of pollutants from water.     

Degradable and chemically recyclable epoxy resins containing acetal linkages: Synthesis,properties, and application for carbon fiber‐reinforced plastics

Four sorts of epoxy resins containing degradable acetal linkages were synthesized by the reaction of bisphenol A (BA) or cresol novolak (CN) resin with vinyl ethers containing a glycidyl group [4‐vinlyoxybutyl glycidyl ether (VBGE) and cyclohexane dimethanol vinyl glycidyl ether (CHDMVG)] and cured with known typical amine‐curing agents. The thermal and mechanical properties of the cured resins were investigated. Among the four cured epoxy resins, the CN‐CHDMVG resin (derived from CN and CHDMVE) exhibited relatively high glass transition temperature (T_g = ca. 110 °C). The treatment of these cured epoxy resins with aqueous HCl in tetrahydrofuran (THF) at room temperature for 12 h generated BA and CN as degradation main products in high yield. Carbon fiber‐reinforced plastics (CFRPs) were prepared by heating the laminated prepreg sheets with BA‐CHDMVG (derived from BA and CHDMVE) and CN‐CHDMVG, in which strands of carbon fibers are impregnated with the epoxy resins containing conventional curing agents and curing accelerators. The obtained CFRPs showed good appearance and underwent smooth breakdown with the aqueous acid treatment in THF at room temperature for 24 h to produce strands of carbon fiber without damaging their surface conditions and tensile strength. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Polyethersulfone‐epoxy terminated materials as thermosetting resins for microelectronic devices

A totally aromatic polyether/sulfone resin (PES‐E) was synthesized and tested as an insulating glue in the construction of a Chip‐on‐Chip (CoC) device. PES‐E, essentially constituted of open‐chain macromolecules of low molecular mass (M _n of about 3000 Da) with hydroxy and/or epoxy end‐groups, has a glass transition temperature of about 150 °C and is subject to crosslinking at temperatures higher than 320 °C. A CoC device was assembled using a five‐step process by interposing a layer of PES‐E between two chips. After curing, SEM cross section images showed a homogeneous crosslinked resin layer well stuck (flick and shear tests) to both chips. The chemical structure of the chains and the hydroxy/epoxy end‐groups ratio were optimized to obtain a crosslinked material with good adhesion and sufficient flexibility to avoid cracking during assembly and use. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5682–5689, 2009     

Investigation of diazo‐derivatization of bisphenol A and its applicability for quantitation in food safety inspections using high‐performance liquid chromatography

Bisphenol A (BPA) is a common additive in food packaging materials, and many methods have been discovered to limit BPA for the sake of food safety. This study aims to find a more sensitive quantification method for BPA. It was determined that a diazo derivative of BPA could be obtained when reacted with a stable and inexpensive reagent, p‐methylaniline, exhibiting an increased response in the ultraviolet spectrum than that of nonreacted BPA. Based on this discovery, an accurate method of BPA quantitation was established using a precolumn derivatization HPLC method. The results of this study showed the low limit of detection and the limit of quantitation for BPA were 3.6 and 10.9 pg/mL on‐column, respectively. This method is proven to have much higher sensitivity and a lower limit of detection than direct HPLC determination methods. This method is robust, easily handled, sensitive and cost‐effective for the quantitation of BPA. In addition, the broad application of this method to determine BPA content in plastic bottled drinking water, distilled water, tap water, milk, Sprite and grape juice was demonstrated in this paper.     

Catalytic enantioselective 1,2-diboration of 1,3-dienes: versatile reagents for stereoselective allylation

More with boron: The development of catalytic enantioselective 1,2-diboration of 1,3-dienes enables a new strategy for enantioselective carbonyl allylation reactions (see scheme). These reactions occur with outstanding levels of stereoselection and can be applied to both monosubstituted and 1,1-disubstituted dienes. The carbonyl allylation reactions provide enantiomerically enriched functionalized homoallylic alcohol products.     

l‐Cysteine‐modified silver‐functionalized silica‐based material as an efficient solid‐phase extraction adsorbent for the determination of bisphenol A

A new silver‐functionalized silica‐based material with a core–shell structure based on silver nanoparticle‐coated silica spheres was synthesized, and silver nanoparticles were modified using strongly bound l‐ cysteine. l‐ Cysteine‐silver@silica was characterized by scanning electron microscopy and FTIR spectroscopy. Then, a solid‐phase extraction method based on l‐ cysteine‐silver@silica was developed and successfully used for bisphenol A determination prior to HPLC analysis. The results showed that the l‐ cysteine‐silver@silica as an adsorbent exhibited good enrichment capability for bisphenol A, and the maximum adsorption saturation was 20.93 mg/g. Moreover, a short adsorption equilibrium time was obtained due to the presence of silver nanoparticles on the surface of the silica. The extraction efficiencies were then optimized by varying the eluents and pH. Under the optimized conditions, good linearity for bisphenol A was obtained in the range from 0.4 to 4.0 μM (R² > 0.99) with a low limit of detection (1.15 ng/mL). The spiked recoveries from tap water and milk samples were satisfactory (85–102%) with relative standard deviations below 5.2% (n = 3), which indicated that the method was suitable for the analysis of bisphenol A in complex samples.     

Efficient access to bisphenol A metabolites: Synthesis of monocatechol,mono-o-quinone,dicatechol, and di-o-quinone of bisphenol A

2-Iodoxybenzoic acid (IBX) oxidation of bisphenol A (BPA) is described. The selective production of either the mono-o-quinone or the di-o-quinone can be controlled by IBX stoichiometry. Isolated yields of quinone were greater than 80%. Previous synthesis of BPA-di-o-quinone using a large excess of Fremy’s salt produced only trace amounts of product. In addition to o-quinone products, both mono- and dicatechols of BPA can synthesize in high yield and isolated without chromatography. The more stable catechols can be quantitatively converted back to o-quinones using silver oxide oxidation in either acetone or DMF. These one-pot reactions provide access to four different BPA metabolites in high yield and significant scale.     

Selective Mono‐allylation of 1,3‐Diketones and Their Use in the Synthesis of 3‐Allyl Chromones and Benzannulated 6,5‐Bicyclic Ketals

The selective mono‐allylation of 1,3‐diketone containing compounds is described. The reaction proceeds under mild reaction conditions and in moderate to high yield (66–99 %). Using this procedure to access the key mono‐allylated intermediate, the hitherto difficult to access 3‐allyl chromones were synthesized in excellent yield (87–98 %). Finally, the utility of this newly developed procedure was showcased through the rapid synthesis of the scaffold of the xyloketal family of natural products.     

Preparation of bio‐based keratin‐derived magnetic molecularly imprinted polymer nanoparticles for the facile and selective separation of bisphenol A from water

In this study, new bio‐based magnetic molecularly imprinted polymer nanoparticles (∼23 nm) were synthesized from keratin extracted from chicken feathers and methacrylate‐functionalized Fe₃O₄ nanoparticles for its potential application in separation and removal of bisphenol A from water. The prepared magnetic molecularly imprinted polymer was characterized by Fourier‐transform infrared spectroscopy, field‐emission scanning electron microscopy, thermogravimetric analysis, alternative gradient field magnetometry, and energy‐dispersive X‐ray spectroscopy. The sorption of bisphenol A was investigated by changing the influencing factors such as pH, immersion time, Fe₃O₄ nanoparticles dosage, and the initial concentration of bisphenol A. Results illustrated that sorption was very fast and efficient (Q_m = 600 mg/g) having a removal efficiency of ∼98% in 40 min of immersion. The adsorption process showed better conformity with the Weber−Morris kinetics and the Freundlich isotherm model. The selectivity of bisphenol A by adsorbent was checked in the presence of hydroquinone, phenol, tetrabromobisphenol, and 4,4′‐biphenol as interferences.     

Flame‐retardant epoxy resins with high glass‐transition temperatures. II. Using a novel hexafunctional curing agent: 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐yl‐tris(4‐aminophenyl) methane

We synthesized a novel phosphorus‐containing triamine [9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐yl‐tris(4‐aminophenyl) methane (dopo‐ta)] from the nucleophilic addition of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐oxide and pararosaniline chloride, using triethylamine as an acid receiver. We confirmed the structure of dopo‐ta by IR, mass, and NMR spectra and elemental analysis. dopo‐ta served as a curing agent for diglycidyl ether of bisphenol A (DGEBA) and dicyclopentadiene epoxy (hp7200). Properties such as the glass‐transition temperature (T_g), thermal decomposition temperature, flame retardancy, moisture absorption, and dielectric properties of the cured epoxy resins were evaluated. The T_g's of cured DGEBA/dopo‐ta and hp7200/dopo‐ta were 171 and 190 °C, respectively. This high T_g phenomenon is rarely seen in the literature after the introduction of a flame‐retardant element. The flame retardancy increased with the phosphorus content, and a UL‐94 V‐0 grade was achieved with a phosphorus content of 1.80 wt % for DGEBA/dopo‐ta/diamino diphenylmethane (DDM) systems and 1.46 wt % for hp7200/dopo‐ta/DDM systems. The dielectric constants for DGEBA/dopo‐ta and hp7200/dopo‐ta were 2.91 and 2.82, respectively, implying that the dopo‐ta curing systems exhibited low dielectric properties. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5971–5986, 2005     

Enantioselective and Catalytic Method for α‐Crotylation of Aldehydes with a Kinetic Self‐Refinement of Stereochemistry

Kinetic refinery : A practical, highly stereoselective, two‐step catalytic protocol for the α‐allylation of aldehydes, starting from crotyltrichlorosilanes, has been developed (see scheme). In each reaction step, one of the stereoisomers reacted faster than the other, which resulted in a kinetic stereochemical (E/Z) self‐refinement of the system and led to the formation of virtually enantiomerically and geometrically pure linear homoallylic alcohols in high yield.