Superconductivity and non-metallicity induced by doping the topological insulators Bi2Se3 and Bi2Te3

We show that by Ca doping the Bi₂Se₃ topological insulator, the Fermi level can be fine tuned to fall inside the band gap and therefore suppresses the bulk conductivity. Non-metallic Bi₂Se₃ crystals are obtained. On the other hand, the Bi₂Se₃ topological insulator can also be induced to become a bulk superconductor, with T_c∼3.8 K, by copper intercalation in the van der Waals gaps between the Bi₂Se₃ layers. Likewise, an as-grown crystal of metallic Bi₂Te₃ can be turned into a non-metallic crystal by slight variation in the Te content. The Bi₂Te₃ topological insulator shows small amounts of superconductivity with T_c∼5.5 K when reacted with Pd to form materials of the type Pd_zBi₂Te₃.     

Electrodeposition of n-type Bi2Te3−ySey thermoelectric thin films on stainless steel and gold substrates

Thermoelectric films of n-Bi₂Te_3−ySe_y were prepared by potentiostatic electrodeposition technique onto stainless steel and gold substrates at room temperature. These films were used for morphological, compositional and structural analysis by environment scanning electron microscope (ESEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The effect of different substrates on the structure and morphology of Bi₂Te_3−ySe_y films and relation between Se content in the electrodepositing solutions and in the films were also investigated. These studies revealed that Bi, Te and Se could be co-deposited to form Bi₂Te_3−ySe_y semiconductor compound in the solution containing Bi³⁺, HTeO₂⁺ and H₂SeO₃. The morphology and structure of the films are sensitive to the substrate material. The doped content of Se element in the Bi₂Te_3−ySe_y compound can be controlled by adjusting the Se⁴⁺ concentration in the electrodepositing solution. X-ray diffraction analysis indicates that the films prepared at −40 mV versus saturated calomel electrode (SCE) exhibit strong (1 1 0) orientation with rhombohedral structure.     

Change of the optical constants of Bi2Te3 single crystals

New structures in the reflectivity spectrum of Bi₂Te₃ are found and assigned to proper critical transitions.     

Switching phenomenon and optical properties of Se85Te10Bi5 films

Se₈₅Te₁₀Bi₅ films of different thicknesses ranging from 126 to 512 nm have been prepared. Energy-dispersive X-ray (EDX) spectroscopy technique showed that films are nearly stoichiometric. X-ray diffraction (XRD) measurements have showed that the Se₈₅Te₁₀Bi₅ films were amorphous. Electrical conduction activation energy (ΔE_σ) for the obtained films is found to be 0.662 eV independent of thickness in the investigated range. Investigation of the current voltage (I-V) characteristics in amorphous Se₈₅Te₁₀Bi₅ films reveals that it is typical for a memory switch. The switching voltage V_th increases with the increase of the thickness and decreases exponentially with temperature in the range from 298 to 383 K. The switching voltage activation energy (ε) calculated from the temperature dependence of V_th is found to be 0.325 eV. The switching phenomenon in amorphous Se₈₅Te₁₀Bi₅ films is explained according to an electrothermal model for the switching process. The optical constants, the refractive index (n) and the absorption index (k) have been determined from transmittance (T) and reflectance (R) of Se₈₅Te₁₀Bi₅ films. Allowed non-direct transitions with an optical energy gap (E_g^opt) of 1.33 eV have been obtained. ΔE_σ is almost half the obtained value of E_g^opt, which suggested band to band conduction as indicated by Davis and Mott.     

Optical and thermoelectric characterizations of electroplated n-Bi2(Te0.9Se0.1)3

Bismuth selenotelluride (Bi₂(Te_0.9Se_0.1)₃) films were electrodeposited at constant current density from acidic aqueous solutions with Arabic gum in order to produce thin films for miniaturized thermoelectric devices. X-ray fluorescence spectroscopy determined film compositions. X-ray diffraction pattern shows that the films as deposited are polycrystalline, isostructural to Bi₂Te₃ and covered by crystallites. Mueller-matrix analysis reveals that the electroplated layers are optically like an isotropic medium. Their pseudo-dielectric functions were determined using mid-infrared spectroscopic ellipsometry. Tauc-Lorentz combined with Drude dispersion relations were successfully used. The energy band gap E_g was found to be about 0.15 eV. Moreover, the fundamental absorption edge was described by an indirect optical band-to-band transition. From Seebeck coefficient measurement, films exhibit n-type charge carrier and the value of thermoelectric power is about −40 μV/K.     

Solvothermal preparation and characterization of nanocrystalline Bi2Te3 powder with different morphology

Bi₂Te₃-based alloys are currently best-known, technological important thermoelectric materials near room temperature. In this paper, nanocrystalline Bi₂Te₃ with different morphologies was synthesized by a solvothermal process based on the reaction between BiCl₃, Te, and KBH₄ in N,N-dimethylformamide at 100-180 °C. KBH₄ was used as a reducing agent. The products were characterized by X-ray diffraction and transmission electron microscopy (TEM). The particle morphologies and size are dependent on the reaction temperature and time. A possible formation mechanism is proposed.     

Magnetic and transport properties of Mn-doped Bi2Se3 and Sb2Se3

We report on the single crystal growth and thermoelectric and magnetic properties of Mn-doped Bi₂Se₃ and Sb₂Se₃ single crystals prepared by the temperature gradient solidification method. The composition and crystal structure were determined using electron probe microanalysis and θ–2θ powder X-ray diffraction studies, respectively. The lattice constants of several percent Mn-doped Bi₂Se₃ and Sb₂Se₃ were slightly smaller than those of the undoped sample due to the smaller Mn atomic radius (1.40 Å) than those of Bi (1.60 Å) and Sb (1.45 Å). Mn-doped Bi₂Se₃ and Sb₂Se₃ showed spin-glass and paramagnetic properties, respectively.     

Electrochemical deposition of Bi2Te3-based thin films

The electrochemical reduction processes on stainless-steel substrates from an aqueous electrolyte composed of nitric acid, Bi³⁺, HTeO₂⁺, SbO⁺ and H₂SeO₃ systems were investigated using cyclic voltammetry. The thin films with a stoichiometry of Bi₂Te₃, Bi_0.5Sb_1.5Te₃ and Bi₂Te_2.7Se_0.3 have been prepared by electrochemical deposition at selected potentials. The structure, composition, and morphology of the films were studied by X-ray diffraction (XRD), environmental scanning electron microscopy (ESEM) and electron microprobe analysis (EMPA). The results showed that the films were single phase with the rhombohedral Bi₂Te₃ structure. The morphology and growth orientation of the films were dependent on the deposition potentials.     

Electrical transport and high thermoelectric properties of PbTe doped with Bi2Te3 prepared by HPHT

In this paper, n-type lead telluride (PbTe) compounds doped with Bi₂Te₃ have been successfully prepared by high pressure and high temperature (HPHT) technique. The composition-dependent thermoelectric properties of PbTe doped with Bi₂Te₃ have been studied at room temperature. The figure-of-merit, Z, for PbTe is very sentivite to the dopants, which could be improved largely although the doped content of Bi₂Te₃ is very small (<0.08 mol%). In addition, the maximum value reaches to 9.3×10⁻⁴ K⁻¹, which is about 20% higher than that of PbTe alloyed with Bi₂Te₃ sintered at ambient pressure (7.6×10⁻⁴ K⁻¹) and several times higher than that of small grain size PbTe containing other dopants. The improved thermoelectric performance in this study may be due to the effect of high pressure and the low lattice thermal conductivity resulting from Bi₂Te₃ as source of dopants.     

Annealing effects on the structural and electrical transport properties of n-type Bi2Te2.7Se0.3 thin films deposited by flash evaporation

N-type Bi₂Te_2.7Se_0.3 thermoelectric thin films with thickness 800 nm have been deposited on glass substrates by flash evaporation method at 473 K. Annealing effects on the thermoelectric properties of Bi₂Te_2.7Se_0.3 thin films were examined in the temperature range 373-573 K. The structures, morphology and chemical composition of the thin films were characterized by X-ray diffraction, field emission scanning electron microscope and energy dispersive X-ray spectroscopy, respectively. Thermoelectric properties of the thin films have been evaluated by measurements of the electrical resistivity and Seebeck coefficient at 300 K. The Hall coefficients were measured at room temperature by the Van der Pauw method. The carrier concentration and mobility were calculated from the Hall coefficient. The films thickness of the annealed samples was measured by ellipsometer. When annealed at 473 K, the electrical resistivity and Seebeck coefficient are 2.7 mΩ cm and −180 μV/K, respectively. The maximum of thermoelectric power factor is enhanced to 12 μW/cm K².     

Thermoelectric properties of Bi2Se3/Bi2Te3/Bi2Se3 and Sb2Te3/Bi2Te3/Sb2Te3 quantum well systems

In this work, we develop a theory of thermoelectric transport properties in two-dimensional semiconducting quantum well structures. Calculations are performed for n-type 0.1 wt.% CuBr-doped Bi₂Se₃/Bi₂Te₃/Bi₂Se₃ and p-type 3 wt.% Te-doped Sb₂Te₃/Bi₂Te₃/Sb₂Te₃ quantum well systems in the temperature range 50–600 K. It is found that reducing the well thickness has a pronounced effect on enhancing the thermoelectric figure of merit (ZT). For the n-type Bi₂Se₃/Bi₂Te₃/Bi₂Se₃ with 7 nm well width, the maximum value of ZT is estimated to be 0.97 at 350 K and for the p-type Sb₂Te₃/Bi₂Te₃/Sb₂Te₃ with well width 10 nm the highest value of the ZT is found to be 1.945 at 440 K. An explanation is provided for the resulting higher ZT value of the p-type system compared to the n-type system.     

Structural characterization of thermally evaporated Bi2Te3 thin films

Thermally evaporated Bi₂Te₃ thin films were deposited on glass substrates. X-ray diffraction study confirmed that the growned films are polycrystalline in nature having hexagonal structure. The film exhibits preferential orientation along the [0 1 5] direction for the films of all thickness together with other abundant planes [0 1 1 1] and [1 1 0]. Various structural parameters such as lattice constants, crystallite size, strain, and dislocation density have been calculated and they are found to be thickness dependent. The lattice parameters are found to be a=4.38 Å and c=30.40 Å. The grain size of the films increases with thickness as the dislocation density and the microstrain decreases with thickness. The mean bond energy and the average coordination number of Bi₂Te₃ thin film are found to be 1.72 eV and 2.4, respectively.     

Inversion of conductivity type in Bi2Te3−xSx crystals

Transport parameters and optical properties of Bi₂Te_3?xS_x single-crystals with x=0–0.18 were studied. With increasing sulphur content the concentration of free current carriers decreases up to x=0.12, due to the interaction of S^x_Te defects with antisite defects Bi^′_Te, and then the p-type conductivity changes to the n-type. The optical gap of Bi₂Te_3?xS_x crystals increases with increasing S content. The obtained results led to the preparation of Bi₂Te₃-Bi₂Te_3?xS_xp–n junction by the heat treatment of p-type Bi₂Te₃ in S vapours.     

Annealing temperature influence on electrical properties of ion beam sputtered Bi2Te3 thin films

Ion beam sputtering process was used to deposit n-type fine-grained Bi₂Te₃ thin films on BK7 glass substrates at room temperature. In order to enhance the thermoelectric properties, thin films are annealed at the temperatures ranging from 100 to 400 °C. X-ray diffraction (XRD) shows that the films have preferred orientations in the c-axis direction. It is confirmed that grain growth and crystallization along the c-axis are enhanced as the annealing temperature increased. However, broad impurity peaks related to some oxygen traces increase when the annealing temperature reached 400 °C. Thermoelectric properties of Bi₂Te₃ thin films were investigated at room temperature. The Bi₂Te₃ thin films, including as-deposited, exhibit the Seebeck coefficients of −90 to −168 μV K⁻¹ and the electrical conductivities of 3.92×10²-7.20×10² S cm⁻¹ after annealing. The Bi₂Te₃ film with a maximum power factor of 1.10×10⁻³ Wm⁻¹ K⁻² is achieved when annealed at 300 °C. As a result, both structural and transport properties have been found to be strongly affected by annealing treatment. It was considered that the annealing conditions reduce the number of potential scattering sites at grain boundaries and defects, thus improving the thermoelectric properties.     

粗糙界面对Bi2Te3/PbTe超晶格热电优值影响的理论分析

以Bi₂Te₃/PbTe超晶格薄膜为例,分析电子在Bi₂Te₃量子阱中的输运过程,综合了薄膜的经典散射效应和理想量子效应,并以此混合效应为基础,在PbTe障碍层厚度一定时,模拟计算了两种混合效应中量子效应占不同比例时,Bi₂Te₃/PbTe超晶格热电优值的变化.在镜面反射占混合效应的0.3时,得到的热电优值与当前报道的量子阱超晶格的实验值接近. 关键词： 超晶格 粗糙界面 热电优值     

Optical properties of surface-modified Bi2O3 nanoparticles

Stearic acid coated Bi₂O₃ nanoparticles in the size range of 5-13 nm were synthesized by the microemulsion method. HRTEM showed that the morphology of Bi₂O₃ nanoparticles was ellipsoidal. The absorption edge of Bi₂O₃ nanoparticles showed a blue shift of ∼0.45 eV, comparing with that of the bulk Bi₂O₃. At room temperature, Bi₂O₃ nanoparticles also showed a strong luminescence at 397 and 420 nm, depending on the excitation wavelength.     

Dielectric parameters in Se70Te30 and Se70Te28Zn2 chalcogenide glasses

Temperature and frequency dependence of dielectric constant (ε′) and dielectric loss (ε″) are studied in glassy Se₇₀Te₃₀ and Se₇₀Te₂₈Zn₂. The measurements have been made in the frequency range (8-500 kHz) and in the temperature range 300 to 350 K. An analysis of the dielectric loss data shows that the Guintini's theory of dielectric dispersion based on two-electron hopping over a potential barrier is applicable in the present case.No dielectric loss peak is observed in glassy Se₇₀Te₃₀. However, such loss peaks exist in the glassy Se₇₀Te₂₈Zn₂ in the above frequency and temperature range. The Cole-Cole diagrams have been used to determine some parameters such as the distribution parameter (α), the macroscopic relaxation time (τ₀), the molecular relaxation time (τ) and the Gibb's free energy for relaxation (ΔF).     

Three- and two-dimensional topological insulators in Pb2Sb2Te5, Pb2Bi2Te5, and Pb2Bi2Se5 layered compounds

The electronic structure of ternary compounds Pb₂Sb₂Te₅, Pb₂Bi₂Te₅, and Pb₂Bi₂Se₅, which have a layered structure that consists of nine-layer atomic blocks separated by van der Waals gaps, has been theoretically studied. It has been shown that all studied compounds are three-dimensional topological insulators. The possibility of the existence of a two-dimensional topological insulator has been found in ultrathin (0001) Pb₂Sb₂Te₅ and Pb₂Bi₂Te₅ films. Oscillations of the ℤ₂ topological invariant with an increase in the film thickness have been observed in the latter compound.     

Study of ferromagnetism in Bi2S3 and ZnS nanocrystalline powders

Results of magnetic measurements suggested that Bi₂S₃ and ZnS nanocrystalline powders prepared by hydrothermal method could possibly exhibit room temperature ferromagnetism. The measured saturation magnetization of the powders increases with an increase of annealing temperature from 300 to 500 °C. Ab initio calculations suggested that the cation vacancies on the surface of Bi₂S₃ and ZnS nanograins could be responsible for the observed magnetic moments. Heat-treatment of Bi₂S₃ or ZnS nanocrystalline powders in Bi or Zn vapor could bring about an enhancement of ferromagnetism. The calculation results indicated that the interstitial Bi or Zn atoms in Bi₂S₃ (0 0 1) or ZnS (0 0 1) surface could induce magnetic moments.     

二维GaTe/Bi2Se3异质结：一类有潜力的Z型光解水催化剂

本文基于第一性原理方法,计算了二维GaTe/Bi₂Se₃异质结的电子结构、界面电荷转移、静电势分布、吸收光谱及光催化性质. 计算结果表明异质结是一个小能隙的准直接半导体,能有效捕获太阳光. 由于相对较强的界面內建极化电场和带边轻微弯曲,导致异质结中的光生电子和空穴分别有效分离在GaTe单层和Bi₂Se₃薄片上,可用于析氢和产氧. 这些理论计算结果意味着二维GaTe/Bi₂Se₃异质结是一类有潜力的Z型太阳能全解水催化剂.