A Copper(II) Ion‐Selective Potentiometric Sensor Based on N,N′,N″,N′′′‐Tetrakis(2‐pyridylmethyl)‐1,4,8,11‐tetraazacyclotetradecane in PVC Matrix

The simple PVC‐based membrane containing N,N′,N″,N′′′‐tetrakis(2‐pyridylmethyl)‐1,4,8,11‐tetraazacyclotetradecane (tpmc) as an ionophore and dibutyl phthalate as a plasticizer, directly coated on a glassy carbon electrode was examined as a new sensor for Cu²⁺ ions. The potential response was linear within the concentration range of 1.0×10^?1–1.0×10^?6 M with a Nernstian slope of 28.8 mV/decade and detection limit of 7.0×10^?7 M. The electrode was used in aqueous solutions over a wide pH range (1.3–6). The sensor exhibited excellent selectivity for Cu²⁺ ion over a number of cations and was successfully used in its determination in real samples.     

Density functional theory study of high‐pressure effect on crystalline 4,4′,6,6′‐tetra(azido)hydrazo‐1,3,5‐triazine

Periodic density functional theory calculations are performed to study the hydrostatic compression effects on the structure, electronic, and thermodynamic properties of the energetic polyazide 4,4′,6,6′‐tetra(azido)hydrazo‐1,3,5‐triazine (TAHT) in the range of 0?100 GPa. At the ambient pressure, the local density approximation/Ceperley‐Alder exchange‐correlation potential parameterized by Perdew and Zunger relaxed crystal structure compares well with the experimental results. The predicted heat of sublimation is 38.68 kcal/mol, and the evaluated condensed phase of formation (414.04 kcal/mol) approximates to the experimental value. The detonation velocity and detonation pressure for the solid TAHT are calculated to be 7.44 km/s and 23.71 GPa, respectively. When the pressure is exerted less than 35 GPa, the crystal structure and geometric parameters change slightly. However, at 36 GPa, the molecular structure, band structure, and density of states change abnormally because of the azide‐tetrazole transformation that has not been observed in gas phase or polar solvents. The azido group cyclizes to form a five‐membered tetrazole ring that is coplanar with the riazine ring and contributes to a larger conjunction system. As the pressure augments further to 80 GPa, the hydrogen transfer is found and a new covalent bond H2? N9 is formed. In the studied pressure range, the band gap decreases generally except for some breaks due to the molecular transformation and drops to nearly zero at 100 GPa, which means the electronic character of the crystal changes toward a metallic system. An analysis of the electronic structure shows that an applied pressure increases the impact sensitivity of TAHT. © 2012 Wiley Periodicals, Inc.     

Highly stable electrochromic polyamides based on N,N‐bis(4‐aminophenyl)‐N′,N′‐bis(4‐tert‐butylphenyl)‐1,4‐phenylenediamine

A new triphenylamine‐containing aromatic diamine monomer, N,N‐bis(4‐aminophenyl)‐N′,N′‐bis(4‐tert‐butylphenyl)‐1,4‐phenylenediamine, was synthesized by an established synthetic procedure from readily available reagents. A novel family of electroactive polyamides with di‐tert‐butyl‐substituted N,N,N′,N′‐tetraphenyl‐1,4‐phenylenediamine units were prepared via the phosphorylation polyamidation reactions of the newly synthesized diamine monomer with various aromatic or aliphatic dicarboxylic acids. All the polymers were amorphous with good solubility in many organic solvents, such as N‐methyl‐2‐pyrrolidinone (NMP) and N,N‐dimethylacetamide, and could be solution‐cast into tough and flexible polymer films. The polyamides derived from aromatic dicarboxylic acids had useful levels of thermal stability, with glass‐transition temperatures of 269–296 °C, 10% weight‐loss temperatures in excess of 544 °C, and char yields at 800 °C in nitrogen higher than 62%. The dilute solutions of these polyamides in NMP exhibited strong absorption bands centered at 316–342 nm and photoluminescence maxima around 362–465 nm in the violet‐blue region. The polyamides derived from aliphatic dicarboxylic acids were optically transparent in the visible region and fluoresced with a higher quantum yield compared with those derived from aromatic dicarboxylic acids. The hole‐transporting and electrochromic properties were examined by electrochemical and spectro‐electrochemical methods. Cyclic voltammograms of the polyamide films cast onto an indium‐tin oxide‐coated glass substrate exhibited two reversible oxidation redox couples at 0.57–0.60 V and 0.95–0.98 V versus Ag/AgCl in acetonitrile solution. The polyamide films revealed excellent elcterochemical and electrochromic stability, with a color change from a colorless or pale yellowish neutral form to green and blue oxidized forms at applied potentials ranging from 0.0 to 1.2 V. These anodically coloring polymeric materials showed interesting electrochromic properties, such as high coloration efficiency (CE = 216 cm²/C for the green coloring) and high contrast ratio of optical transmittance change (ΔT%) up to 64% at 424 nm and 59% at 983 nm for the green coloration, and 90% at 778 nm for the blue coloration. The electroactivity of the polymer remains intact even after cycling 500 times between its neutral and fully oxidized states. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2330–2343, 2009     

N,N,N′,N′,N″‐Pentamethyl‐N″‐[(trifluorosilyl)methyl] phosphoric triamide. First example of the existence of intramolecular PO→Si coordination bond in the Si‐containing phosphoric triamides

The N,N,N′,N′,N″‐pentamethyl‐N″‐(trifluorosilylmethyl)phosphoric triamide O?P(NMe₂)₂N(Me) CH₂SiF₃ with intramolecular P?O→Si coordination was formed by the reaction of N,N,N′,N′,N″‐pentamethyl‐N″[(triethoxysilyl)methyl]phosphoric triamide with BF₃·Et₂O. Copyright © 2007 John Wiley & Sons, Ltd.     

Poly(ethylene terephthalate) reinforced by N,N′‐diphenyl biphenyl‐3,3′,4,4′‐tetracarboxydiimide moieties

Starting with 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and methyl aminobenzoate, we synthesized a novel rodlike imide‐containing monomer, N,N′‐bis[p‐(methoxy carbonyl) phenyl]‐biphenyl‐3,3′,4,4′‐tetracarboxydiimide (BMBI). The polycondensation of BMBI with dimethyl terephthalate and ethylene glycol yielded a series of copoly(ester imide)s based on the BMBI‐modified poly(ethylene terephthalate) (PET) backbone. Compared with PET, these BMBI‐modified polyesters had higher glass‐transition temperatures and higher stiffness and strength. In particular, the poly(ethylene terephthalate imide) PETI‐5, which contained 5 mol % of the imide moieties, had a glass‐transition temperature of 89.9 °C (11 °C higher than the glass‐transition temperature of PET), a tensile modulus of 869.4 MPa (20.2 % higher than that of PET), and a tensile strength of 80.8 MPa (38.8 % higher than that of PET). Therefore, a significant reinforcing effect was observed in these imide‐modified polyesters, and a new approach to higher property polyesters was suggested. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 852–863, 2002; DOI 10.1002/pola.10169     

Two new thiophosphoramide structures: N,N′,N′′‐tricyclohexylphosphorothioic triamide and O,O′‐diethyl (2‐phenylhydrazin‐1‐yl)thiophosphonate

The compound N,N′,N′′‐tricyclohexylphosphorothioic triamide, C₁₈H₃₆N₃PS or P(S)[NHC₆H₁₁]₃, (I), crystallizes in the space group Pnma with the molecule lying across a mirror plane; one N atom lies on the mirror plane, whereas the bond‐angle sum at the other N atom has a deviation of some 8° from the ideal value of 360° for a planar configuration. The orientation of the atoms attached to this nonplanar N atom corresponds to an anti orientation of the corresponding lone electron pair (LEP) with respect to the P=S group. The P=S bond length of 1.9785 (6) Å is within the expected range for compounds with a P(S)[N]₃ skeleton; however, it is in the region of the longest bond lengths found for analogous structures. This may be due to the involvement of the P=S group in N—H...S=P hydrogen bonds. In O,O′‐diethyl (2‐phenylhydrazin‐1‐yl)thiophosphonate, C₁₀H₁₇N₂O₂PS or P(S)[OC₂H₅]₂[NHNHC₆H₅], (II), the bond‐angle sum at the N atom attached to the phenyl ring is 345.1°, whereas, for the N atom bonded to the P atom, a practically planar environment is observed, with a bond‐angle sum of 359.1°. A Cambridge Structural Database [CSD; Allen (2002). Acta Cryst. B 58 , 380–388] analysis shows a shift of the maximum population of P=S bond lengths in compounds with a P(S)[O]₂[N] skeleton to the shorter bond lengths relative to compounds with a P(S)[N]₃ skeleton. The influence of this difference on the collective tendencies of N...S distances in N—H...S hydrogen bonds for structures with P(S)[N]₃ and P(S)[O]₂[N] segments were studied through a CSD analysis.     

Syntheses,Structures and Characterization of Four Metal‐Organic Frameworks constructed by 2,2′,6,6′‐Tetramethoxy‐4,4′‐biphenyldicarboxylic Acid

Four metal‐organic frameworks (MOFs), {[Mn_3.5L(OH)(HCOO)₄(DMF)] · H₂O} ( 1 ), {[In_2.5L₂O(OH)_1.5(H₂O)₂] · DMF · CH₃CN · 2H₂O} ( 2 ), {[Pb₄L₃O(DMA)] · CH₃CN} ( 3 ), and {[LaL(NO₃)(DMF)₂] · 2H₂O} ( 4 ) were synthesized by utilizing the ligand 2,2′,6,6′‐tetramethoxy‐4,4′‐biphenyldicarboxylic acid (H₂L) via solvothermal methods. All MOFs were characterized by single‐crystal X‐ray diffraction, powder X‐ray diffraction, thermogravimetric analysis, and infrared spectroscopy. In 1 , the Mn²⁺ ions are interconnected by formic groups in situ produced via DMF decomposition to form a rare 2D macrocyclic plane, which is further linked by L^2– to construct the final 3D network. In 2 , 1D zip‐like infinite chain is formed and then interconnected to build the 3D framework. In 3 , a [Pb₆(μ₄‐O)₂(O₂C)₁₀(DMA)₂] cluster with a centrosymmetric [Pb₆(μ₄‐O)₂]⁸⁺ octahedral core is formed in the 3D structure. In 4 , the La³⁺ ions are connected with each other through carboxylate groups of L^2– to generate 1D zigzag chain, which is further linked by L^2– to construct a 3D network with sra topology. Solid photoluminescence properties of 3 and 4 were also investigated.     

Synthesis and Properties of N,N′‐Bis(difuroxano [3,4‐b:3′,4′‐d]phenyl)oxalic Amide

N,N′‐Bis(difuroxano[3,4‐b:3′,4′‐d]phenyl)oxalic amide was synthesized via acylation, nitration, azidation, and pyrolysis‐denitrogenation from the starting materials of oxalyl chloride and 3,5‐dichloroaniline, under mild reaction conditions, with the yields of 81.0%, 82.0%, 86.0% and 81.7% respectively. The title compound and its precursors were characterized by ¹H NMR, IR, MS, and elemental analysis. The title compound has a density of 1.92 g·cm^?3 by a suspension method, a standard formation enthalpy of 979 kJ·mol^?1 calculated by Gaussian programs, a detonation velocity of 8.17 km·s^?1, and a detonation pressure of 31 GPa obtained by Kamlet Equation. The thermal decomposition reactions of the title compound at different heating rates were tested by differential scanning calorimetry (DSC). The kinetics parameters of the pyrolysis of the compound were calculated by Kissinger's method. The values of apparent activation energy (E_a) and pre‐exponential constant (A) were 226.7 kJ·mol^?1 and 10^23.17 s^?1 respectively. It was presupposed that N,N′‐bis(difuroxano[3,4‐b:3′,4′‐d]phenyl)oxalic amide would be a promising high energetic explosive with low sensitivity.     

Synthesis of N,N′,X‐tridentate 2‐iminomethylpyrrole‐coordinated palladium(II) complexes via N─H bond activation of pyrrole moiety

The reaction of [Pd(CH₃CN)₂Cl₂] with N ‐functional group‐substituted 2‐iminomethylpyrrole‐based ligands, namely N ¹‐((1H‐pyrrol‐2‐yl)methylene)‐N ³,N ³‐dimethylpropane‐1,3‐diamine (L_A), N ¹‐((1H‐pyrrol‐2‐yl)methylene)‐N ³‐methyl‐N ³‐phenylpropane‐1,3‐diamine (L_B), N ‐((1H‐pyrrol‐2‐yl)methylene)‐3‐(methylthio)propan‐1‐amine (L_C) and N ‐((1H‐pyrrol‐2‐yl)methylene)‐3‐methoxypropan‐1‐amine (L_D), resulted in [L_n PdCl] (L_n  = L_A–L_D) complexes in high yield via N─H bond activation of pyrrole moiety without use of base. [L_n PdCl] existed as monomeric four‐coordinated complexes with slightly distorted square planar geometries around the palladium metal center. The ligands show N ,N ′,X ‐tridentate binding mode to the palladium metal center to give two fused ring metallacycles. [L_BPdCl] gave the highest activity (3.29 × 10⁵ g PMMA (mol Pd)⁻¹ h⁻¹) for a methyl methacrylate (MMA) polymerization in the presence of modified methylaluminoxane at 60 °C compared to the other Pd(II) analogues, and resulted in PMMA with higher molecular weight (M _w = 7.16 × 10⁵ g mol⁻¹) and narrower polydispersity index. Syndiotactic‐enriched PMMA resulted in all cases.     

Tetra(N,N′‐tetramethylharnstoff)‐Beryllium‐Triiodid, [Be(TMH)4](I3)2

Tetra(N,N′‐tetramethylurea)‐beryllium‐triiodide, [Be(TMU)₄](I₃)₂ ( 1 ) was prepared from beryllium powder and iodine in N,N′‐tetramethylurea to give orange crystals, which were characterized by X‐ray diffraction and IR spectroscopy. Compound 1 crystallizes monoclinically in the space group C2/c with four formula units per unit cell. Lattice dimensions at 100(2) K: a = 1906.6(1), b = 1185.7(1), c = 1895.0(1) pm, β = 113.60(1) °, R₁ = 0.0291. The structure of 1 consists of distorted tetrahedral cations [Be(TMU)₄]²⁺ with Be–O bond lengths of 162.5(5) and 160.8(5) pm and triiodide ions without site symmetry.     

N,N,N′,N′,N″‐penta(methyl acrylate)diethylenetriamine: A novel ligand for atom transfer radical polymerization of methyl methacrylate

A novel ligand, N,N,N′,N′,N″‐penta (methyl acrylate) diethylenetriamine (MA₅‐DETA), was synthesized by the reaction of diethylenetriamine with methyl acrylate in almost quantitive yield. The polymerizations of methyl methacrylate with MA₅‐DETA as the ligand and α,α‐dichlorotoluene (DCT) and ethyl 2‐bromoisobutyrate (2‐EBiB) as the initiators, respectively, under different conditions were examined. The polymerization with CuCl/MA₅‐DETA/DCT was closely controlled in bulk and gave polymers with quite narrow molecular weight distributions (M_w/M_n's) of 1.16–1.29. The polymerization with the system CuBr/MA₅‐DETA/EBiB in bulk gave high activity. However, the system was not well controlled and gave the polymers with M_w/M_n = 1.35–1.53. The solution polymerization in anisole with CuBr/MA₅‐DETA/EBiB showed a better‐controlled nature. Moreover, the addition of CuBr₂ into the aforementioned system can further improve its controllability. The M_w/M_n's of the resulting polymers ranged from 1.11 to 1.21. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1963–1969, 2004     

Masking of Lewis acidity trends in the solid‐state structures of trichlorido‐ and tribromido(2,2′:6′,2′′‐terpyridine‐κ3N,N′,N′′)gallium(III)

The molecular structures of trichlorido(2,2′:6′,2′′‐terpyridine‐κ³N,N′,N′′)gallium(III), [GaCl₃(C₁₅H₁₁N₃)], and tribromido(2,2′:6′,2′′‐terpyridine‐κ³N,N′,N′′)gallium(III), [GaBr₃(C₁₅H₁₁N₃)], are isostructural, with the Ga^III atom displaying an octahedral geometry. It is shown that the Ga—N distances in the two complexes are the same within experimental error, in contrast to expected bond lengthening in the bromide complex due to the lower Lewis acidity of GaBr₃. Thus, masking of the Lewis acidity trends in the solid state is observed not only for complexes of group 13 metal halides with monodentate ligands but for complexes with the polydentate 2,2′:6′,2′′‐terpyridine donor as well.     

N‐Germyl derivatives of sulfacetamide and ortho‐(sulfonamido)phenylamines: characterization of N‐[o‐(N′,N′‐dimethylsulfonamido)phenyl]‐N‐dimesitylgermaimine

Triethylgermylation of sulfacetamide occurs on the sulfonamido nitrogen in competition with the 1,2 addition of the starting triethylgermyl dimethylamine on the carbonyl group. Thermal decomposition in the presence of dimethylamine yields N‐triethylgermylsulfanilamide. Stable 1:1 sulfacetamide–DBU and 1:1 sulfacetamide–Et₃N complexes were isolated and fully characterized in the course of dehydrochlorination reactions. o‐Sulfonamidophenylamine yields N,N′‐bis‐triethylgermylated derivatives, whereas o‐(N,N‐dimethylsulfonamido)phenylamine leads to monogermylated compounds. The N‐dimethylaminodimesitylgermyl derivative is thermally stable. Dehydrohalogenation of the N‐dimesitylfluorogermyl compound leads to the thermally stable but water sensitive N‐[o‐(N′,N′‐dimethylsulfonamido)phenyl]‐N‐dimesitylgermaimine. Copyright © 2003 John Wiley & Sons, Ltd.     

Synthesis and properties of new soluble aromatic polyamides and polyimides on the basis of N,N′‐bis(3‐aminobenzoyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine

A new N‐phenylated amide (N‐phenylamide) unit containing aromatic diamine, N,N′‐bis(3‐aminobenzoyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine, was prepared by the condensation of N,N′‐diphenyl‐1,4‐phenylenediamine with 3‐nitrobenzoyl chloride, followed by catalytic reduction. Two series of organosoluble aromatic poly(N‐phenylamide‐imide)s and poly(N‐phenylamide‐amide)s with inherent viscosities of 0.58–0.82 and 0.56–1.21 dL/g were prepared by a conventional two‐stage method and the direct phosphorylation polycondensation, respectively, from the diamine with various aromatic dianhydrides and aromatic dicarboxylic acids. All polyimides and polyamides are amorphous and readily soluble in many organic solvents such as N,N‐dimethylacetamide and N‐methyl‐2‐pyrrolidone. These polymers could be solution cast into transparent, tough, and flexible films with high tensile strengths. These polyimides and polyamides had glass‐transition temperatures in the ranges of 230–258 and 196–229 °C, respectively. Decomposition temperatures of the polyimides for 10% weight loss all occurred above 500 °C in both nitrogen and air atmospheres. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2564–2574, 2002     

Syntheses of multicyclic poly(ether sulfone)s from 5,5′,6,6′‐tetrahydroxy‐3,3,3′,3′‐tetramethyl spirobisindane and 4,4′‐bis(4‐chlorophenyl) sulfones

5,5′,6,6′‐Tetrahydroxy‐3,3,3′,3′‐tetramethyl spirobisindane (TTSBI) was polycondensed with 4,4′‐dichlorodiphenyl sulfone (DCDPS) or with 4,4′‐bis(4‐chlorophenyl sulfonyl) biphenyl (BCSBP) in DMSO. Concentration and feed ratio were optimized to avoid gelation and to obtain a maximum yield of multicyclic polyethers free of functional groups. Regardless of these reaction conditions, only low fractions of perfect multicycles were obtained from DCDPS apparently due to steric hindrance of ring closure. Under the same conditions high fractions of perfect multicycles were achieved with the longer and more flexible DCSBP. The reaction products were characterized by MALDI‐TOF mass spectrometry, ¹H‐NMR spectroscopy viscosity, and DSC measurements. Relatively low glass transition temperatures (T_gs ≈ 160–175 °C) were found. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3732–3739, 2008     

Copper(II) Complexes with N‐(9‐anthracenyl)‐N′‐(3‐pyridyl)urea (L) and a Derivative of L: Synthesis,Structure, and Fluorescent Properties

Three copper(II) complexes, [Cu₂(OAc)₄L₂] · 2CH₃OH ( 1 ), [CuBr₂L′₂(CH₃OH)] · CH₃OH ( 2a ), and [CuBr₂L′₂(DMSO)] · 0.5CH₃OH ( 2b ) {L = N‐(9‐anthracenyl)‐N′‐(3‐pyridyl)urea and L′ = N‐[10‐(10‐methoxy‐anthronyl)]‐N′‐(3‐pyridyl)urea} have been synthesized by the reaction of L with the corresponding copper(II) salts. Complex 1 shows a dinuclear structure with a conventional “paddlewheel” motif, in which four acetate units bridge the two Cu^II ions. In complexes 2a and 2b , the anthracenyl ligand L has been converted to an anthronyl derivative L′, and the central metal ion exhibits a distorted square pyramidal arrangement, with two pyridyl nitrogen atoms and two bromide ions defining the basal plane and the apical position is occupied by a solvent molecule (CH₃OH in 2a and DMSO in 2b ).     

Monomolecular sheets of propeller‐shaped triethyl 4,4′,4′′‐[benzene‐1,3,5‐triyltris(ethyne‐2,1‐diyl)]tribenzoate deuterochloroform monosolvate

The title compound, C₃₉H₃₀O₆·CDCl₃, has a chemical threefold axis and an approximately planar structure, with an ethoxycarbonyl substituent on each of the terminal benzenes oriented in the same direction, thus forming a propeller‐shaped molecule. This molecule is of particular interest in the field of metal–organic frameworks (MOFs), where its hydrolyzed analogue forms MOF structures with high surface areas. The benzene ring which occupies the centre of the molecule forms π–π interactions to the equivalent benzene ring at a perpendicular distance of 3.32 (1) Å. Centrosymmetric dimers formed in this way are interconnected by intermolecular C—H...π interactions with a rather short H...CgA distance of 2.51 Å (CgA is the centroid of the central benzene ring). The molecules are arranged in regular parallel sheets. Within a sheet, molecules are interconnected via C—H...O interactions where all carbonyl O atoms participate in weak hydrogen bonds as hydrogen‐bond acceptors. Neighbouring sheets are connected through the above‐mentioned π–π and C—H...π interactions.     

Interaction of Bovine Serum Albumin with N‐(4‐Ethoxyphenyl)‐N′‐(4‐Antipyrinyl)Thiourea (EPAT) Using Spectroscopies

The interaction between N‐(4‐ethoxyphenyl)‐N′‐(4‐antipyrinyl)thiourea (EPAT) and bovine serum albumin (BSA) was studied by fluorescence spectroscopy in combination with UV absorption spectroscopy. The intrinsic fluorescence of bovine serum albumin was quenched by EPAT through a static quenching procedure. The binding constants of EPAT with BSA were estimated according to the fluorescence quenching results at different temperatures. The thermodynamic parameters: enthalpy change (ΔH) and entropy change (ΔS) were calculated to be ?10.69 kJ/mol and 42.64 J·mol^?1·K^?1 according to thermodynamic equations, respectively, and indicating that the binding force was suggested to be mainly a hydrophobic force. The effect of common ions on the binding constant was also investigated. A new fluorescence spectroscopy assay of the proteins was presented in this paper. The determination results of the proteins in bovine serum by means of this method were very close to those obtained using Coomassie Brilliant Blue G‐250 colorimetry.     

Synthesis and Structure of MnCl2(HDpyF) (HDpyF = N,N′‐di(2‐pyridyl)formamidine): New Crystallographic Disorder and Bonding Mode of the HDpyF Ligand

The reaction of N,N′‐di(2‐pyridyl)formamidine (HDpyF) with MnCl₂‐4H₂O afforded the complex MnCl₂(HDpyF), which was characterized by X‐ray crystallography. The HDpyF ligand chelates to the Mn(II) center through the first and the third nitrogen atoms to form a six‐membered ring, leaving the second and the fourth nitrogen atoms uncoordinated. The HDpyF ligand is crystallographically disordered such that two different molecules can be solved. The neutral HDpyF ligand adopts the new s‐cis‐syn‐s‐trans conformation.