首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 281 毫秒
1.
Experimental results are presented about the effects of ionic strength and pH on the mean drop-size after emulsification and on the coalescence stability of emulsions, stabilized by a globular protein beta-lactoglobulin (BLG). The mean drop-size is determined by optical microscopy, whereas the coalescence stability is characterized by centrifugation. In parallel experiments, the zeta-potential and protein adsorption on drop surface are determined. The experiments are performed at two different BLG concentrations, 0.02 and 0.1 wt%. The electrolyte concentration in the aqueous phase, C(EL), is varied between 1.5 mM and 1 M, and pH is varied between 4.0 and 7.0. The experiments show that the mean drop-size after emulsification depends slightly on C(EL), at fixed protein concentration and natural pH = 6.2. When pH is varied, the mean drop-size passes through a maximum at fixed protein and electrolyte concentrations. A monolayer protein adsorption is registered in the studied ranges of C(EL) and pH at low BLG concentration of 0.02 wt%. In contrast, a protein multilayer is formed at higher BLG concentration, 0.1 wt%, above a certain electrolyte concentration (C(EL) > 100 mM, natural pH). The experimental results for the emulsion coalescence stability are analyzed by considering the surface forces acting between the emulsion drops. The electrostatic, van der Waals, and steric interactions are taken into account to calculate the barriers in the disjoining pressure isotherm at the various experimental conditions studied. The comparison of the theoretically calculated and the experimentally determined coalescence barriers shows that three qualitatively different cases can be distinguished. (1) Electrostatically stabilized emulsions, with monolayer protein adsorption, whose stability can be described by the DLVO theory. (2) Sterically stabilized emulsions, in which the drop-drop repulsion is created mainly by overlapping protein adsorption multilayers. A simple theoretical model is shown to describe emulsion stability in these systems. (3) Sterically stabilized emulsions with a monolayer adsorption on drop surface.  相似文献   

2.
The influence of isothermal heat treatments on the adsorption of anionic carrageenan molecules to the surfaces of anionic beta-lactoglobulin-coated droplets has been investigated. The zeta-potential, mean particle diameter, microstructure, and creaming stability of emulsions containing beta-lactoglobulin-coated droplets and/or carrageenan molecules that had previously been heat treated at temperatures ranging from 30 to 90 degrees C for 20 min were measured (pH 6.0, 150 mM NaCl). Three different heat treatments were used to establish the physicochemical origin of the influence of thermal history on the adsorption of carrageenan molecules to the protein coated droplets: (i) droplets and carrageenan were mixed at room temperature, then heated together; (ii) droplets were heated, cooled to room temperature, then mixed with carrageenan; (iii) carrageenan was heated, cooled to room temperature, then mixed with droplets. For treatments i and ii appreciably more carrageenan adsorbed to the protein-coated droplet surfaces at temperatures < or = 60 degrees C than at higher temperatures. For treatment iii, carrageenan adsorbed to the droplet surfaces across the whole temperature range. These results suggest that an irreversible thermal denaturation of the adsorbed beta-lactoglobulin molecules inhibited the adsorption of carrageenan molecules to the droplet surfaces. We postulate that there is a patch of positive charge on the surface of the native globular protein molecules which becomes more diffuse upon thermal denaturation. We found that the carrageenan molecules were unable to protect the beta-lactoglobulin-coated droplets at high temperatures (T > 60 degrees C) because they desorbed from the droplet surfaces. Nevertheless, adsorption of iota-carrageenan was capable of protecting the droplets against flocculation caused by surface denaturation of the adsorbed proteins at lower temperatures (T < or = 50 degrees C).  相似文献   

3.
The influence of surface and thermal denaturation of adsorbed beta-lactoglobulin (beta-Lg) on the flocculation of hydrocarbon oil droplets was measured at pH 3 and compared with that at pH 7. Oil-in-water emulsions (5 wt % n-hexadecane, 0.5 wt % beta-Lg, pH 3.0) were prepared that contained different levels of salt (0-150 mM NaCl) added immediately after homogenization. The mean particle diameter (d43) and particle size distribution of diluted emulsions were measured by laser diffraction when they were either (i) stored at 30 degrees C for 48 h or (ii) subjected to different thermal treatments (30-95 degrees C for 20 min). In the absence of salt, little droplet flocculation was observed at pH 3 or 7 because of the strong electrostatic repulsion between the droplets. In the presence of 150 mM NaCl, a progressive increase in mean particle size with time was observed in pH 7 emulsions during storage at 30 degrees C, but no significant change in mean particle diameter with time (d43 approximately 1.4 +/- 0.2 microm) was observed in the pH 3 emulsions. Droplet aggregation became more extensive in pH 7 emulsions containing salt (added before thermal processing) when they were heated above 70 degrees C, which was attributed to thermal denaturation of adsorbed beta-Lg leading to interdroplet disulfide bond formation. In contrast, the mean particle size decreased and the creaming stability improved when pH 3 emulsions were heated above 70 degrees C. These results suggest that the droplets in the pH 3 emulsions were weakly flocculated at temperatures below the thermal denaturation temperature of beta-Lg (T < 70 degrees C) but that flocs did not form so readily above this temperature, which was attributed to a reduction in droplet surface hydrophobicity due to protein conformational changes. The most likely explanation for the difference in behavior of the emulsions is that disulfide bond formation occurs much more readily at pH 7 than at pH 3.  相似文献   

4.
The effect of heating has been studied for whey protein-stabilised oil-in-water emulsions (25.0% (w/w) soybean oil, 3.0% (w/w) whey protein isolate, pH 7.0). These emulsions were heated between 55 and 95 °C as a function of time and the effect on particle size distribution, adsorbed protein amount, protein conformation and rheological properties was determined. Heating the emulsions as a function of temperature for 25 min resulted in an increase of the mean diameter (d32) and shear viscosity with a maximum at 75 °C. Heating of the emulsions at different temperatures as a function of time in all cases resulted in a curve with a maximum for d32. A maximum increase of d32 was observed after about 45 min at 75 °C and after 6–8 min at 90 °C. Similar trends were observed with viscosity measurements. Confocal scanning laser micrographs showed that after 8 min of heating at 90 °C large, loose aggregates of oil droplets were formed, while after 20 min of heating compact aggregates of two or three emulsion droplets remained. An increase of the adsorbed amount of protein was found with increasing heating temperature. Plateau values were reached after 10 min of heating at 75 °C and after 5 min of heating at 90 °C. Based on these results we concluded that in the whole process of aggregation of whey protein-stabilised emulsions an essential role is played by the non-adsorbed protein fraction, that the kinetics of the aggregation of whey protein-stabilised emulsions follow similar trends as those for heated whey protein solutions and that upon prolonged heating rearrangements take place leading to deaggregation of initially formed large, loose aggregates of emulsion droplets into smaller, more compact ones.  相似文献   

5.
The objectives of this study were to examine the influence interfacial composition on environmental stresses stability of oil in water emulsions. An electrostatic layer-by-layer deposition method was used to create the multilayered interfacial membranes with different compositions: (i) primary emulsion (Soy protein Isolate); (ii) secondary emulsion (Soy protein Isolate – OSA-starch); (iii) tertiary emulsion (Soy protein isolate – OSA-starch – chitosan). Fourier transform-infrared (FTIR) and scanning electron microscopy (SEM) results confirmed the adsorption of charged polyelectrolyte onto oppositely charge polyelectrolyte-coated oil droplets. The stability of primary, secondary, and tertiary emulsions to thermal treatment (30 min at 30–90°C), pH (3–7) and NaCl (0–500 mM) were determined using ζ-potential, particle diameter, and microstructure analysis. Primary emulsions were unstable at pH 4–7, salt concentrations, and thermal treatments. Secondary emulsions were stable to creaming and droplet aggregation at pH 3–5, at ≤50 mM NaCl, and unstable at thermal treatments, whereas tertiary emulsions were stable at all salt concentrations, thermal treatments, and at pH 3–6. These results demonstrate that these polymers can be used to engineer oil in water emulsion systems and improve the emulsion stability to environmental stresses.  相似文献   

6.
Adsorbed films of milk proteins at the oil-water (O-W) interface have been imaged using a Brewster angle microscope (BAM). Special adaptations were made to the BAM to allow imaging of the O-W interface and to enable in situ heating and cooling of the adsorbed films. The proteins beta-lactoglobulin (beta-L) and alphas1-, beta-, and kappa-casein were studied over a range of bulk protein concentrations (Cb) and surface ages at pH 7 and for beta-L at pH 5 also. The adsorbed films were subjected to incremental compression and expansion cycles, such that the film area was typically varied between 125% and 50% of the original film area, and the resulting film structure was recorded via the BAM at 25.0 degrees C. Structuring of beta-L films (the formation of ridges and cracks) was more pronounced at pH 5 (closer to the protein's isoelectric point) than at pH 7 and for longer adsorption times and/or higher Cb. Structuring was also much more apparent at the O-W interface than at the A-W interface on compression/expansion/aging, especially at pH 7. After heating beta-L films adsorbed at low Cb (0.005 wt %) to 80 or 90 degrees C, an even greater degree of film structuring was evident, but beta-L films adsorbed at higher Cb (> or =0.05 wt %) showed fewer but larger fractures. The adsorbed caseins showed little evidence of such features, either before or after heating, apart from slight structuring for the heated films of alphas1- and kappa-casein films after 1 day. Changes in the dilatational elastic modulus of the beta-L films (Cb = 0.005 wt %) were correlated with the variations in the structural integrity of the films as observed via the BAM technique. In particular, there was a marked increase in the elastic modulus on heating, while the cycle of compression and expansion appeared to result in a net film weakening overall. The beta-L films adsorbed at higher Cb (> or =0.05 wt %) behaved as if an even stronger elastic skin completely covered the interface. The overall conclusion is that interfacial protein films subjected to these types of thermal and mechanical perturbations, which are typical of those that occur in food colloid processing, can become highly inhomogeneous, depending on the type of protein and the bulk solution conditions. This undoubtedly has implications for the stability of the corresponding emulsions and foams.  相似文献   

7.
The conformation and structural dimensions of α-lactalbumin (α-La) both in solution and adsorbed at oil-water interfaces of emulsions were investigated using synchrotron radiation circular dichroism (SRCD) spectroscopy, front-face tryptophan fluorescence (FFTF) spectroscopy, and dual polarization interferometry (DPI). The near-UV SRCD and the FFTF results demonstrated that the hydrophobic environment of the aromatic residues located in the hydrophobic core of native α-La was significantly altered upon adsorption, indicating the unfolding of the hydrophobic core of α-La upon adsorption. The far-UV SRCD results showed that adsorption of α-La at oil-water interfaces created a new non-native secondary structure that was more stable to thermally induced conformational changes. Specifically, the α-helical conformation increased from 29.9% in solution to 45.8% at the tricaprylin-water interface and to 58.5% at the hexadecane-water interface. However, the β-sheet structure decreased from 18.0% in solution to less than 10% at both oil-water interfaces. The DPI study showed that adsorption of α-La to a hydrophobic C18-water surface caused a change in the dimensions of α-La from the native globule-like shape (2.5-3.7 nm) to a compact/dense layer approximately 1.1 nm thick. Analysis of the colloidal stability of α-La stabilized emulsions showed that these emulsions were physically stable against droplet flocculation at elevated temperatures both in the absence and in the presence of 120 mM NaCl. In the absence of salt, the thermal stability of emulsions was due to the strong electrostatic repulsion provided by the adsorbed α-La layer, which was formed after the adsorption and structural rearrangement. In the presence of salt, although the electrostatic repulsion was reduced via electrostatic screening, heating did not induce strong and permanent droplet flocculation. The thermal stability of α-La stabilized emulsions in the presence of salt is a combined effect of the electrostatic repulsion and the lack of covalent disulfide interchange reactions. This study reports new information on the secondary and tertiary structural changes of α-La upon adsorption to oil-water interfaces. It also presents new results on the physical stability of α-La stabilized emulsions during heating and at moderate ionic strength (120 mM NaCl). The results broaden our understanding of the factors controlling protein structural change at emulsion interfaces and how this affects emulsion stability.  相似文献   

8.
Using positively charged plate-like layered double hydroxides (LDHs) particles as emulsifier, liquid paraffin-in-water emulsions stabilized solely by such particles are successfully prepared. The effects of the pH of LDHs aqueous dispersions on the formation and stability of the emulsions are investigated here. The properties of the LDHs dispersions at different pHs are described, including particle zeta potential, particle aggregation, particle contact angle, flow behavior of the dispersions and particle adsorption at a planar oil/water interface. The zeta potential decreases with increasing pH, leading to the aggregation of LDHs particles into large flocs. The structural strength of LDHs dispersions is enhanced by increasing pH and particle concentration. The three-phase contact angle of LDHs also increases with increasing pH, but the variation is very small. Visual observation and SEM images of the interfacial particle layers show that the adsorption behavior of LDHs particles at the planar oil/water interface is controlled by dispersion pH. We consider that the particle-particle (at the interface) and particle-interface electrostatic interactions are well controlled by adjusting the dispersion pH, leading to pH-tailored colloid adsorption. The formation of an adsorbed particle layer around the oil drops is crucial for the formation and stability of the emulsions. Emulsion stability improves with increasing pH and particle concentration because more particles are available to be adsorbed at the oil/water interface. The structural strength of LDHs dispersions and the gel-like structure of emulsions also influence the stability of the emulsions, but they are not necessary for the formation of emulsions. The emulsions cannot be demulsified by adjusting emulsion pH due to the irreversible adsorption of LDHs particles at the oil/water interface. TEM images of the emulsion drops show that a thick particle layer forms around the oil drops, confirming that Pickering emulsions are stabilized by the adsorbed particle layers. The thick adsorbed particle layer may be composed of a stable inner particle layer which is in direct contact with the oil phase and a relatively unstable outer particle layer surrounding the inner layer.  相似文献   

9.
The protein concentration is known to determine the stability against coalescence during formation of emulsions. Recently, it was observed that the protein concentration also influences the stability of formed emulsions against flocculation as a result of changes in the ionic strength. In both cases, the stability was postulated to be the result of a complete (i.e. saturated) coverage of the interface. By combining the current views on emulsion stability against coalescence and flocculation with new experimental data, an empiric model is established to predict emulsion stability based on protein molecular properties such as exposed hydrophobicity and charge. It was shown that besides protein concentration, the adsorbed layer (i.e. maximum adsorbed amount and interfacial area) dominates emulsion stability against coalescence and flocculation. Surprisingly, the emulsion stability was also affected by the adsorption rate. From these observations, it was concluded that a completely covered interface indeed ensures the stability of an emulsion against coalescence and flocculation. The contribution of adsorption rate and adsorbed amount on the stability of emulsions was combined in a surface coverage model. For this model, the adsorbed amount was predicted from the protein radius, surface charge and ionic strength. Moreover, the adsorption rate, which depends on the protein charge and exposed hydrophobicity, was approximated by the relative exposed hydrophobicity (QH). The model in the current state already showed good correspondence with the experimental data, and was furthermore shown to be applicable to describe data obtained from literature.  相似文献   

10.
Understanding the factors that control protein structure and stability at the oil-water interface continues to be a major focus to optimize the formulation of protein-stabilized emulsions. In this study, a combination of synchrotron radiation circular dichroism spectroscopy, front-face fluorescence spectroscopy, and dual polarization interferometry (DPI) was used to characterize the conformation and geometric structure of β-lactoglobulin (β-Lg) upon adsorption to two oil-water interfaces: a hexadecane-water interface and a tricaprylin-water interface. The results show that, upon adsorption to both oil-water interfaces, β-Lg went through a β-sheet to α-helix transition with a corresponding loss of its globular tertiary structure. The degree of conformational change was also a function of the oil phase polarity. The hexadecane oil induced a much higher degree of non-native α-helix compared to the tricaprylin oil. In contrast to the β-Lg conformation in solution, the non-native α-helical-rich conformation of β-Lg at the interface was resistant to further conformational change upon heating. DPI measurements suggest that β-Lg formed a thin dense layer at emulsion droplet surfaces. The effects of high temperature and the presence of salt on these β-Lg emulsions were then investigated by monitoring changes in the ζ-potential and particle size. In the absence of salt, high electrostatic repulsion meant β-Lg-stabilized emulsions were resistant to heating to 90 °C. Adding salt (120 mM NaCl) before or after heating led to emulsion flocculation due to the screening of the electrostatic repulsion between colloidal particles. This study has provided insight into the structural properties of proteins adsorbed at the oil-water interface and has implications in the formulation and production of emulsions stabilized by globular proteins.  相似文献   

11.
The influence of thermal processing on droplet flocculation in oil-in-water emulsions stabilized by either beta-lactoglobulin (primary emulsions) or beta-lactoglobulin-iota-carrageenan (secondary emulsions) at pH 6 has been investigated. In the absence of salt, the zeta-potential of the primary emulsion was less negative (-40 mV) than that of the secondary emulsion (-55 mV) due to adsorption of anionic iota-carrageenan to the anionic beta-Lg-coated droplet surfaces. The zeta-potential and mean diameter (d(43) approximately 0.3 microm) of droplets in primary and secondary emulsions did not change after storage at temperatures ranging from 30 to 90 degrees C. In the presence of 150 mM NaCl, the zeta-potential of the primary emulsion was much less negative (-27 mV) than that of the secondary emulsion (-50 mV), suggesting that the latter was less influenced by electrostatic screening effects. The zeta-potential of the primary emulsions did not change after storage at elevated temperatures (30-90 degrees C). The zeta-potential of the secondary emulsions became less negative, and the aqueous phase iota-carrageenan concentration increased at storage temperatures exceeding 50 degrees C, indicating iota-carrageenan desorbed from the beta-Lg-coated droplets. In the primary emulsions, appreciable droplet flocculation (d(43) approximately 8 microm) occurred at temperatures below the thermal denaturation temperature (T(m)) of the adsorbed proteins due to surface denaturation, while more extensive flocculation (d(43) > 20 microm) occurred above T(m) due to thermal denaturation. In the secondary emulsions, the extent of droplet flocculation below T(m) was reduced substantially (d(43) approximately 0.8 microm), which was attributed to the ability of adsorbed carrageenan to increase droplet-droplet repulsion. However, extensive droplet flocculation was observed above T(m) because carrageenan desorbed from the droplet surfaces. Differential scanning calorimetry showed that iota-carrageenan and beta-Lg interacted strongly in aqueous solutions containing 0 mM NaCl, but not in those containing 150 mM NaCl, presumably because salt weakened the electrostatic attraction between the molecules.  相似文献   

12.
Oil-in-water emulsions (pH 7.0 or pH 3.0) containing 30 wt% soya oil and various concentrations of lactoferrin were made in a two-stage valve homogenizer. The average droplet size (d32), the surface protein coverage (mg/m2) and composition, and the zeta-potential of the emulsions were determined. The value of d32 decreased with increasing lactoferrin concentration up to 1%, and then was almost independent of lactoferrin concentration beyond 1% at both pH 7.0 and pH 3.0. The surface protein coverage of the emulsions made at pH 7.0 increased almost linearly with increasing lactoferrin concentration from 0.3 to 3%, but increased only slightly in emulsions made at pH 3.0 at lactoferrin concentrations >1%. The surface protein coverage of the emulsions made at pH 3.0 was lower than that of the emulsions made at pH 7.0 at a given protein concentration. The emulsion droplets had a strong positive charge at both pH 7.0 and pH 3.0, indicating that stable cationic emulsion droplets could be formed by lactoferrin alone. When emulsions were formed with a mixture of lactoferrin and beta-lactoglobulin (beta-lg) (1:1 by weight), the charge of the emulsion droplets was neutralized at pH 7.0 suggesting the formation of electrostatic complexes between the two proteins. The composition of the droplet surface layer showed that both proteins were adsorbed, presumably as complexes, from the aqueous phase at pH 7.0 in equal proportions, whereas competitive adsorption occurred between lactoferrin and beta-lg at pH 3.0. At this pH, beta-lg was adsorbed in preference to lactoferrin at low protein concentrations (1%), whereas lactoferrin appeared to be adsorbed in preference to beta-lg at high protein concentrations.  相似文献   

13.
The objective of this study was to investigate the effects of environmental stress and emulsifier types on the stability of curcumin emulsions. Results showed that Lecithin and Tween 80 presented good emulsifying capacity. The Tween 80 emulsion was the most stable among the four emulsions.

The particle sizes of Tween 80 and whey protein emulsion were relatively smaller than gum arabic and lecithin. Extensive droplet aggregation appeared in whey protein-stabilized emulsions when the pH was approximately isoelectric point (pI) with salt concentration >200?mM. Lecithin emulsion was unstable when pH?≤?6 with salt concentration >100?mM. There was little impact of pH and ionic strength on gum arabic and Tween 80 emulsions. All of the emulsions were stable at temperatures from 30 to 90°C in the absence of salt. These results help characterize the emulsifying and stabilizing abilities of emulsifier types intended for applications in the food industry.  相似文献   

14.
The investigation of the effect of multilayer membranes on the stability of flaxseed oil-in-water (o/w) emulsions was the main goal of this study. The primary emulsion was prepared by homogenizing the oil phase (10 wt%) with an aqueous sodium caseinate solution (90 wt% and a pH 6.8) using a high-pressure microfluidizer. This emulsion was mixed with a pectin solution to form a secondary emulsion at a pH 6.8 and then adjusted to a pH to 3 for the adsorption of anionic pectin molecules on the surface of the cationic droplet surfaces. The pH effect on the physical stability of the emulsions was evaluated by measuring the mean particle diameter, ζ-potential, creaming index, and visualization of the microstructure. Also, the oxidative stability was determined by monitoring the lipid hydroperoxides and thiobarbituric acid-reactive substances (TBARs) at 55°C. The results of this study indicate that a multilayer structure had a positive effect on the improvement of the physical and oxidative stability of the conventional emulsions under certain pH conditions and limited storage period.  相似文献   

15.
The influence of environmental conditions (pH, NaCl, CaCl2, and temperature) on the properties and stability of oil-in-water (O/W) emulsions containing oil droplets surrounded by one-, two-, or three-layer interfacial membranes has been investigated. Three oil-in-water emulsions were prepared with the same droplet concentration and buffer (5 wt % corn oil, 5 mM phosphate buffer, pH 6) but with different biopolymers: (i) primary emulsion: 0.5 wt % beta-Lg; (ii) secondary emulsion: 0.5 wt % beta-Lg, 0.1 wt % iota-carrageenan; (iii) tertiary emulsion: 0.5 wt % beta-Lg, 0.1 wt % iota-carrageenan, 0-2 wt % gelatin. The secondary and tertiary emulsions were prepared by electrostatic deposition of the charged biopolymers onto the surfaces of the oil droplets so as to form two- and three-layer interfacial membranes, respectively. The stability of the emulsions to pH (3-8), sodium chloride (0-500 mM), calcium chloride (0-12 mM), and thermal processing (30-90 degrees C) was determined. We found that multilayer emulsions had better stability to droplet aggregation than single-layer emulsions under certain environmental conditions and that one or more of the biopolymer layers could be made to desorb from the droplet surfaces in response to specific environmental changes (e.g., high salt or high temperature). These results suggest that the interfacial engineering technology used in this study could lead to the creation of food emulsions with improved stability to environmental stresses or to emulsions with triggered release characteristics.  相似文献   

16.
Effects of substituting native beta-lactoglobulin B (beta-lactoglobulin) with heat-treated beta-lactoglobulin as emulsifier in oil in water emulsions were investigated. The emulsions were prepared with a dispersed phase volume fraction of Phi=0.6, and accordingly, oil droplets rather closely packed. Native beta-lactoglobulin and beta-lactoglobulin heated at 69 degrees C for 30 and 45 min, respectively, in aqueous solution at pH 7.0 were compared. Molar mass determination of the species formed upon heating as well as measurements of surface hydrophobicity and adsorption to a planar air/water interface were made. The microstructure of the emulsions was characterized using confocal laser scanning microscopy, light scattering measurements of oil droplet sizes, and assessment of the amount of protein adsorbed to surfaces of oil droplets. Furthermore, oil droplet interactions in the emulsions were quantified rheologically by steady shear and small and large amplitude oscillatory shear measurements. Adsorption of heated and native beta-lactoglobulin to oil droplet surfaces was found to be rather similar while the rheological properties of the emulsions stabilized by heated beta-lactoglobulin and the emulsions stabilized by native beta-lactoglobulin were remarkably different. A 200-fold increase in the zero-shear viscosity and elastic modulus and a 10-fold increase in yield stress were observed when emulsions were stabilized by heat-modified beta-lactoglobulin instead of native beta-lactoglobulin. Aggregates with a radius of gyration in the range from 25 to 40 nm, formed by heating of beta-lactoglobulin, seem to increase oil droplet interactions. Small quantities of emulsifier substituted with aggregates have a major impact on the rheology of oil in water emulsions that consist of rather closely packed oil droplets.  相似文献   

17.
Heat stability has been studied in model systems of oil-in-water emulsions (3 wt.% total protein, 45 vol.% n-tetradecane, pH 6.8, ionic strength 30-50 mM) with pure beta-lactoglobulin (beta-lg) as the main emulsifier. The effect of small additions of sodium caseinate, beta-casein or alpha s1-casein prior to emulsion preparation has been investigated. Samples heated for 3 min at 90 degrees C were monitored with respect to changes in viscosity and particle-size distribution. As expected, the pure beta-lg-stabilized emulsions were susceptible to heat-induced changes. But the replacement of just 1% of the beta-lg by sodium caseinate (0.03 wt.% caseinate in the total emulsion) led to complete elimination of any heat-induced viscosity or particle size increase. These findings show that a very small proportion of casein can inhibit the susceptibility of a beta-lg-based emulsion to heat-induced destabilization. The magnitude of the effect is dependent on the type of casein, with the order of effectiveness being beta-casein>sodium caseinate>alpha s1-casein. This work has potential implications for the development of milk protein-stabilized emulsions of improved shelf life.  相似文献   

18.
Diacylglycerol (DAG)/water and triacylglycerol (TAG)/water emulsions were prepared using beta-lactoglobulin (beta-LG) as an emulsifier. The oil phase (20% in emulsion) was mixed with beta-LG solution (1% beta-LG in water, pH 7) to prepare the emulsions. A fine oil-in-water emulsion was produced from both DAG and TAG oils. The interfacial protein concentration of the TAG emulsion was higher than that of the DAG emulsion. The zeta potential of the DAG oil droplet was higher than that of the TAG oil droplet. The front-surface fluorescence spectroscopy results revealed that tryptophan residues in beta-LG moved to the more hydrophobic environment during the adsorption of protein on the oil droplet surfaces. Changes in secondary structure of beta-LG during the adsorption were determined by FT-IR spectroscopy. Decreases in the beta-sheet content concomitant with increases in the alpha-helix content were observed during the adsorption to the oil droplets, and the degree of structural change was greater for beta-LG in the TAG emulsion than in the DAG emulsion, indicating the increased unfolding of adsorbed beta-LG on the TAG oil droplet surface. Results of interfacial tension measurement supported this speculation, that is, the increased unfolding of the protein at the TAG-water interface. Trypsin- and proteinase K-catalyzed proteolysis was used to probe the topography of the adsorbed beta-LG on the oil droplet surface. SDS-PAGE analyses of liberated peptides after the proteolysis indicated the higher susceptibility of beta-LG adsorbed on the DAG oil droplet surface than on the TAG oil droplet surface. On the basis of all the results, we discussed the conformation of the adsorbed beta-LG on the two oil droplet surfaces.  相似文献   

19.
The influence of protein concentration and order of addition relative to homogenization (before or after) on the extent of droplet flocculation in heat-treated oil-in-water emulsions stabilized by a globular protein were examined using laser diffraction. n-Hexadecane (10 wt%) oil-in-water emulsions (pH 7, 150 mM NaCl) stabilized by beta-lactoglobulin (beta-Lg) were prepared by three methods: (1) 4 mg/mL beta-Lg added before homogenization; (2) 4 mg/mL beta-Lg added before homogenization and 6 mg/mL beta-Lg added after homogenization; (3) 10 mg/mL beta-Lg added before homogenization. The emulsions were then subjected to various isothermal heat treatments (30-95 degrees C for 20 min), with the 150 mM NaCl being added either before or after heating. Emulsion 1 contained little nonadsorbed protein and exhibited extensive droplet aggregation at all temperatures, which was attributed to the fact that the droplets had a high surface hydrophobicity, e.g., due to exposed oil or extensive protein surface denaturation. Emulsions 2 and 3 contained a significant fraction of nonadsorbed beta-Lg. When the NaCl was added before heating, these emulsions were relatively stable to droplet flocculation below a critical holding temperature (75 and 60 degrees C, respectively) but showed extensive flocculation above this temperature. The stability at low temperatures was attributed to the droplets having a relatively low surface hydrophobicity, e.g., due to complete saturation of the droplet surface with protein or due to more limited surface denaturation. The instability at high temperatures was attributed to thermal denaturation of the adsorbed and nonadsorbed proteins leading to increased hydrophobic interactions between droplets. When the salt was added to Emulsions 2 and 3 after heating, little droplet flocculation was observed at high temperatures, which was attributed to the dominance of intra-membrane over inter-membrane protein-protein interactions. Our data suggests that protein concentration and order of addition have a strong influence on the flocculation stability of protein-stabilized emulsions, which has important implications for the formulation and production of many emulsion-based products.  相似文献   

20.
The properties of milk protein-stabilised, oil-in-water emulsions are determined by the structure and surface rheology of the adsorbed layer at the oil-water interface. Analysis of the segment density profiles normal to the surface show differences in the structure between adsorbed layers of disordered casein and globular whey protein. Systematic studies of stability and rheology of model oil-in-water emulsion systems made with milk proteins as sole emulsifiers give insight into the relation between adsorbed layer properties and bulk emulsion stability. Of particular importance are effects of pH, temperature, calcium ions and protein content. Colloidal interactions between adsorbed layers on different surfaces can be inferred from an analysis of dynamic collisions of protein-coated emulsion droplets in shear flow using the colloidal particle scattering technique. The role of competitive adsorption on emulsion properties can be derived from experiments on systems containing mixtures of milk proteins and small-molecule surfactants. Shear-induced destabilisation is especially influenced by the presence of fat crystals in the emulsion droplets. Aggregated gel network properties are dependent on the balance of weak and strong interparticle interactions. In heat-set whey protein emulsion gels, the rheological behaviour is especially sensitive to surfactant type and concentration. Rearrangements of transient caseinate-based emulsion gels can have a profound influence on the quiesent stability behaviour. Computer simulation provides a general link between particle interactions, microstructure and rheological properties.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号