Preparation of Poly (L-lactic Acid) Microsphere

Poly (L-lactic acid) (PLLA) microspheres were prepared by a solvent evaporation method based on an oil/water emulsion. The effect of the mass ratio of PLLA and poly(vinyl alcohol) (PVA) on the formation of the microspheres was discussed, and the influence of extraction speed of dichloromethane on the microsphere morphology was also studied. Moreover, the influences of the PLLA concentration and the volume ratio of water phase to dichloromethane phase were investigated. The results showed that stable microspheres can be obtained under the conditions that the mass ratio of PLLA to PVA is 20:1. Porous microspheres were obtained under faster evaporating speed of dichloromethane. The microsphere size increased with increasing PLLA concentration. The microsphere size also increased with the increase of the volume ratio of water phase to dichloromethane phase.     

Improving the Barrier Properties of Poly(Lactic Acid) by Blending with Poly(Ethylene-Co-Vinyl Alcohol)

Poly(lactic acid) (PLA)/poly(ethylene-co-vinyl alcohol) (EVOH) blends were prepared via melt blending to improve the barrier properties of PLA. The phase morphologies and final properties (rheological behavior, thermal and dynamical-mechanical features, barrier properties, and mechanical behaviors) of the blends were investigated as a function of the EVOH content. The results indicated that hydroxyl groups of EVOH promoted the degradation of PLA, and thus affected the viscosities and morphologies of the resulting blends. The intrinsic viscosities of PLA in the blends decreased with the content of EVOH. The PLA and EVOH presented typical phase-separated morphologies, with a relatively small domain size of the EVOH phase. The EVOH enhanced the cold-crystallization behavior of PLA. The barrier properties to water vapor and oxygen increased linearly with increasing EVOH content.     

Mechanical,Biodegradation and Morphological Properties of Sisal Fiber Reinforced Poly(Lactic Acid) Biocomposites

Sisal fiber-reinforced poly(lactic acid) (SF/PLA) biocomposites were prepared by melt mixing and subsequent compression molding. The effect of fiber content and sodium hydroxide (NaOH) concentration, used for the fiber mercerization, on the properties of the biocomposites was investigated. It was found that the SFs had a large potential for improving the mechanical properties of the biocomposites. The tensile strength and impact strength increased linearly up to a fiber content of 20%, and then decreased due to the fiber agglomeration. The water absorption was enhanced with increasing the SF content owing to the SFs containing an abundance of hydroxyl groups. The biodegradability of the SF/PLA biocomposites increased similarly. Furthermore, the mercerization led to an increase of the mechanical properties of the biocomposites, which normally depended on the fiber-matrix adhesion. The mercerization had competing effects on the water absorption and biodegradability, including not only the positive function of the improved hydrophilicity of the mercerized-SF but also the negative role of the increase of fiber-matrix interfacial adhesion. Overall, the optimum SF load for mechanical properties was 20?wt% due to a good balance between the reinforcement and distribution of the SFs, whereas the 6% NaOH concentration was optimal owing to the resulting fibers yielding the highest mechanical properties and acceptable water resistance and biodegradability.     

On Localization of Clay Nanoparticles in Polypropylene/poly(Lactic Acid) Blend Nanocomposites: Correlation with Mechanical Properties

Two polypropylene (PP)/polylactide (PLA)/clay ternary nanocomposite systems, i.e. PP-rich and PLA-rich ones, each containing various amounts of one of two types of clay, were prepared by one step melt compounding in a twin screw extruder. The microstructures of the developed systems were correlated with tensile and impact properties. A theoretical calculation using wetting coefficients was used for predicting the clay nanoparticles localization in the blends. The nanoparticles were almost completely located within the PLA phase in both the PP-rich and PLA-rich systems, in good agreement with the predictions. Addition of a compatibilizer led to localization of the nanoparticles at the interfaces of the blends. From the wide angle X-ray scattering (WAXS) spectra it was concluded that the incorporation of clay led to intercalated structures in the both systems. The increase in impact toughness of the compatibilized blend nanocomposites, with respect to the uncompatibilized ones, was attributed to the weakened interfacial debonding in the presence of the interfacial-localized nanoparticles.     

Melting and Crystallization Behaviors of Poly(Lactic Acid) Modified with Graphene Acting as a Nucleating Agent

Graphene (GN)-filled polylactic acid (PLA) nanocomposites were prepared through a solution blending method with GN weight percent ranging from 0.5 to 2?wt%. Rheological, melting and crystallization behaviors of the prepared PLA/GN nanocomposites were investigated by means of dynamic rheological measurements and differential scanning calorimetry (DSC). The shear viscosities of the PLA/GN nanocomposites decreased with increasing GN content, which was remarkably different from previous reports on the modifications using traditional nanofillers (e.g., clay, carbon nanotubes, etc.). The nonisothermal melt crystallization kinetic analysis suggested that GN served as a nucleating agent and could considerably promote the PLA’s crystallization through heterogeneous nucleation. Our findings suggested that at relatively low cooling rates (??≤?10?°C/min) even a small amount of GN promoted the nucleation and considerably increased the crystallization rate. However, the crystallinity began to decrease at higher cooling rates (e.g., ??≥?20?°C/min), especially when the GN content was high (e.g., 2?wt%), possibly owing to the GN aggregation effect considering PLA is a slowly crystallizing polymer.     

The Effect of Talc on the Mechanical,Crystallization and Foaming Properties of Poly(Lactic Acid)

Poly(lactic acid) (PLA)/talc composites containing different contents of talc were prepared by melt blending. Multiple properties of the prepared composites were investigated including mechanical, rheological and crystallization as well as foaming properties. Tensile test results indicated that the mechanical properties of the composite with 3% wt. talc showed significant reinforcement and toughening effect. When the talc content reached 10%, Young's modulus of the composite was increased by 35% compared with pure PLA. The morphological results showed that the talc layers were partially delaminated and uniformly dispersed in the PLA matrix at low loading. Differential scanning calorimetry (DSC) and polarized optical microscopy (POM) results indicated that 3% wt. talc significantly increased the crystallinity of the PLA matrix. The thermogravimetric analysis (TGA) results demonstrated that the thermal stability of PLA/talc composites was enhanced as well. Moreover, talc at low loading could act as a plasticizer in the polymer flow, which was investigated by rheological tests. The batch foaming experiments revealed that 3% wt. talc loading had the most notable heterogeneous nucleation effect, with the cell size decreasing from 15.4 μm for neat PLA to 8.5 μm and the cell density increasing by 298%.     

Crystallization Behavior of Poly(Lactic Acid) Filled with Modified Carbon Black

A novel method was employed to modify the surface of carbon black (CB) by an organic small molecule in a Haake Rheomix mixer. The modified carbon black (MCB) was dispersed uniformly in poly(lactic acid; PLA). The crystallization behaviors of PLA, PLA/CB and PLA/MCB composites were investigated by differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD), small-angle X-ray scattering (SAXS) and polarizing optical microscopy. It is found that the addition of CB or MCB can influence the crystallization behavior of PLA. PLA/MCB has a faster crystallization rate and higher crystallization peak temperature than PLA/CB. For non-isothermal studies, Jeziorny and Mo equations were employed. The Mo equation can well describe the non-isothermal crystallization of the three samples. For PLA/CB and PLA/MCB composites containing 3wt% fillers, the nucleating activity for CB is about 0.32, and about 0.16 for MCB. All these results show that MCB is an effective nucleating agent. PLA/MCB has a higher nucleation rate than PLA/CB because of the finer dispersed particles size and improved interaction between MCB and PLA.     

Preparation and Characterization of Composites Based on Poly (Butylene Succinate) and Poly (Lactic Acid) Grafted Tetracalcium Phosphate

Tetracalcium phosphate (TTCP, Ca₄(PO₄)₂O) was functionalized by poly (l-lactic acid) (PLLA) in order to improve the dispersion of TTCP particles in poly (butylene succinate) (PBS) matrices, and then a series of the PLLA grafted TTCP/PBS (g-TTCP/PBS) composites were prepared via melt processing. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), tensile analysis, differential scanning calorimetry (DSC), thermogravimetric analysis (DTG/TGA) and melt rheological analysis were used to investigate the structure and properties of the g-TTCP/PBS composites. The results revealed that l-lactide could be grafted onto the surface of TTCP, and the g-TTCP/PBS composites showed the best mechanical properties when the content of g-TTCP was 10 wt%. The crystallization temperature of g-TTCP/PBS composites tended to increase with the increase of g-TTCP contents. The functionalized particles played an important role in augmenting the thermal degradation rate and the complex viscosity of the composites due to their unique structure and the reasonable interfacial interaction between the particles and PBS matrix.     

Phase Structure of Compatibilized Poly(Lactic Acid)/Linear Low-Density Polyethylene Blends

Blends of PLA and linear low-density polyethylene (LLDPE) were compatibilized with glycidyl methacrylate (GMA)–grafted poly(ethylene-octene) copolymer (mPOE). Effects of compatilizer on phase structure of compatibilized PLA/LLDPE were studied by spreading coefficient calculation prediction, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and wide-angle X-ray diffraction (WAXD) analysis. The spreading coefficient calculations, based on experimental and calculated surface tension data, show that mPOE spreads on LLDPE extensively to encapsulate LLDPE completely, which is in good agreement with the results of DSC, SEM, and WAXD analysis. The chemical reaction between the end carboxyl groups or end hydroxyl groups of PLA and epoxy groups of mPOE, which is suggested as the driving force leading to an ideal interfacial adhesion between PLA and the dispersed phase, was confirmed by Fourier transform infrared ray (FT-IR) spectroscopy analysis.     

Mechanical and Thermal Properties Enhancement of Poly(Lactic Acid)/Halloysite Nanocomposites by Maleic-Anhydride Functionalized Rubber

Poly(lactic acid) (PLA)/halloysite composites were prepared using melt compounding followed by compression molding. Maleic anhydride grafted styrene-ethylene/butylene-styrene (SEBS-g-MAH) was used to toughen the PLA composites. The mechanical properties of the PLA composites were studied through tensile, flexural, and impact tests. The thermal properties were characterized by using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The fracture surfaces of the composites were assessed by using field emission scanning electron microscopy (FESEM). The impact strength and thermal properties of the PLA/halloysite composites were increased by addition of SEBS-g-MAH.     

Isothermal Crystallization and Melting Behavior of Composites Composed of Poly(L-lactic Acid) and Poly(glycolic Acid) Fibers

Several composites of poly (L-lactic acid) (PLLA) with poly (glycolic acid) (PGA) fibers were prepared. The isothermal crystallization kinetics and melting behavior of PLLA and all of the composites were characterized by using differential scanning calorimetry. The experimental data were processed by using the Avrami equation. The relative parameters, such as the Avrami exponent and half-time crystallization, revealed that PGA fibers had positive effects on the crystallization of PLLA, but these effects had only a minimal dependence on the PGA fiber content. Moreover, at low isothermal crystallization temperatures (85°C～110°C), recrystallization during the heating scan was observed, which could lower the melting point of the samples to a certain extent.     

Designing and Characterization of Biodegradable Multiblock Poly(L-Lactic Acid)/Polybutadiene Elastomers

A series of poly(L-lactic acid)/polybutadiene (PLA/PB) biodegradable multiblock elastomers was synthesized and characterized. A two-step process to prepare PLA/PB multiblock elastomers was applied. Melt polymerization was used to prepare poly(L-lactic acid) (PLA) terminated with hydroxyl groups and, at the same time, hydroxyl-terminated polybutadiene (HTPB) and 1,6-hexamethylene diisocyanate (HDI) were employed to synthesize diisocyanate-terminated polybutadiene (ITPB). Then, PLA and ITPB were reacted with different PLA/PB weight ratios. Consequently, a series of PLA/PB biodegradable poly(ester-urethane)s with crosslinked chains was obtained. Swelling characteristics and crosslink density of the crosslinked elastomer were investigated. DMA was applied to characterize its thermal properties. The measurement of mechanical properties showed that a PLA/PB elastomer with adjustable mechanical properties was synthesized. Micromorphology, hydrophobicity, and degradability of the material were also characterized.     

Properties and Morphology of Poly(Lactic Acid)/Calcium Carbonate Whiskers Composites Prepared by a Vane Mixer based on an Extensional Flow Field

Binary composites of poly(lactic acid) (PLA)/calcium carbonate whiskers (CCW) with different weight fractions were prepared with a vane mixer based on extensional rheology. The mechanical properties, thermostability, crystallization behavior, rheology behaviors and micromorphology of the composites were analysed to study the effect of the CCW fibers on the composite's properties; a pure PLA sample was also prepared for comparison. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) revealed that the CCW fibers had excellent compatibility with the PLA matrix and the CCW fibers were dispersed and distributed evenly in the PLA matrix under the action of the extensional flow field produced by the vane mixer. Differential scanning calorimetric (DSC) analysis showed that introducing a vane mixer into the PLA processing could increase the degree of crystallization (χ_c) of the composites significantly, and moderate CCW fibers adding could further increase its χ_c value. Thermogravimetric analysis (TGA) revealed that adding the CCW fibers reduced the thermostability of the composites. The G′, G″, η* and the torque, T_N, of the composites, obtained from rheology analyses, declined obviously, because of the hydrolysis and chains scission induced by residual water and fatty acid when the CCW content less than 4%. Tensile tests proved that filling moderate amounts of CCW fibers into PLA could increase its tensile strength and strain at break, increasing by 5% and 29.6%, respectively.     

Temperature and pH-Responsive Polyacrylamide/Poly(Acrylic Acid) Interpenetrating Polymer Network Nanoparticles

The synthesis, by two sequential inverse microemulsion polymerizations, of interpenetrating polymer networks (IPN) formed by polyacrylamide (PAM) and poly(acrylic acid) (PAA) and their response to changes in pH and temperature are reported here. The temperature and pH responses of the IPN nanoparticles are compared with those of polyacrylamide and random copolymers of polyacrylamide and poly(acrylic acid) P(AM-co-AA) nanoparticles also made by inverse microemulsion polymerization. We found that only the IPN nanogels exhibited a sharp swelling increase with temperature associated with its Upper Consolute Solution Temperature, driven by hydrogen bonding interactions, and with pH, driven by electrostatic repulsions of the PAA carboxylic groups, especially at pHs larger than the pK_a of the PAA. The ?-potentials of the PAM, P(AM-co-AA) and IPN nanogels were measured as a function of pH and temperature, to determine the effects of these two variables, which in turn, affected the swelling of the nanogels. Field emission scanning electron microscopy revealed that the IPN nanogels were spheroidal with sizes similar to those determined by dynamic light scattering.     

Evaluation of the Complexation Process Between Poly(Aspartic Acid) and Poly(Ethylene Glycol) Through Dynamic Rheology and Electrokinetic Potential

Investigations concerning the interactions between the polymeric pair constituted of poly(aspartic acid) (PAS) as a proton-donating polycarboxilic acid and poly(ethylene glycol) (PEG) as a proton-accepting compound are continued from previous studies. The complexation between PAS and PEG has potential use as a matrix for encapsulation of bioactive substances with potential biomedical applications. The interactions that occurred were monitored in dilute solutions by determining the particle size distribution and the zeta potential (ZP) through laser light scattering method; data associated with oscillatory rheology was used as a complementary analysis. The influence of the ratio between the components and the temperature conditions during the complexation process brought additional data concerning the intermolecular links formed through hydrogen bonds.     

Synthesis and Characterization of Biodegradable Poly(lactic-co-glycolic acid)

A series of poly(lactic-co-glycolic acid) (PLGA) was synthesized by bulk ring-opening copolymerization with different ratios of L-lactic acid (L-LA) to glycolic acid (GA); stannous octoate [Sn(Oct)2] was used as catalyst. The structures were characterized by FT-IR. The crystallinity and the glass-transition temperature (T_g) were studied by differential scanning calorimeter (DSC). T_g decreased with the increase of GA and the rate of degradation and degree of hydrophilicity increased with the increased content of GA.     

Preparation and Properties of Novel Maleated Poly (D,L-lactide-co-glycolide) Porous Scaffolds for Tissue Engineering

Three-dimensional biodegradable porous scaffolds play an important role in tissue engineering. A new polymer based on maleated poly(lactic-co-glycolic acid) (MPLGA) was synthesized using direct melt copolymerization from maleic anhydride (MAH), D, L-lactide, and glycolide monomers. MPLGA porous biodegradable scaffolds were prepared by a solution-casting/salt-leaching method. The effects of content and size of the NaHCO₃ porogen on the compressive strength of the MPLGA scaffolds were investigated, and the effect of content of the porogen on the porosity of the MPLGA scaffolds was also studied. The results indicated that MAH was grafted onto PLGA successfully and MPLGA scaffolds with interconnective and open pore structure were obtained. Increasing content of NaHCO₃ porogen resulted in an increase of porosity and decrease of the compressive strength of the MPLGA scaffolds with the compressive strength of the scaffolds also decreasing with increasing porogen size.     

聚邻甲基丙烯酰胺基苯甲酸/纳米ZnO复合物的制备及其荧光性能研究

利用原子转移自由基聚合(ATRP)法对合成的新单体邻甲基丙烯酰胺基苯甲酸(o-MAABA)进行聚合,通过核磁验证得到符合预先设计的、结构明确的聚合物,聚合物分子量为7900;将纳米ZnO引入到该聚合物P(o-MAABA)中,得到聚合物/纳米ZnO粒子复合物.用红外光谱和差热分析方法对聚合物和复合物进行了表征,并采用透射电镜(TEM)观察了复合物粒子的形貌.红外光谱表明纳米ZnO确实被引入到聚合物链中,并且与聚合物中的某些官能团发生了一定的相互作用;差热分析表明P(o-MAABA)/纳米ZnO复合物的热稳定性较原来聚合物P(o-MAABA)有所提高;TEM观察表明复合物粒子基本为球状,表面较为光滑.P(o-MAABA)/纳米ZnO复合物表现出特殊的荧光性能,与聚合物相比荧光光谱发生红移,并且复合物溶解性较好,能成膜,可望在发光材料方面得到应用.     

A Change of Phase Morphology in Poly Lactic Acid/Poly Methyl Methacrylate Blends Induced by Graphene Nano Sheets

Blending of polymeric materials is an effective way to obtain materials with specific properties, since the properties of these multiphase polymeric materials are not only affected by the properties of the component polymers but also by the morphology formed. The research described here was focused on investigation of the morphology of polymer blends of poly lactic acid (PLA) and poly methyl methacrylate (PMMA) and the PLA/PMMA blends containing various amounts of graphene nano plates, (GNP). In this work, the blends were prepared by solution casting and the morphologies of these nano filled polymer blends were studied. By adding graphene nano plates into the PLA/PMMA blends, the morphology changed for all compositions. It was very interesting to note that the GNP were found to be preferentially located in one of the polymer phases, different for the different loadings, and its location determined the final morphology of the PLA/PMMA blends. The morphology of the blends was observed by SEM and the composition-morphology dependence responses were investigated using a Fourier transform infra-red (FTIR) spectroscopy technique.     

Poly(allylamine) Stabilized Iron Oxide Magnetic Nanoparticles

This paper describes a new method for the dispersing and surface-functionalization of metal oxide magnetic nanoparticles (10 nm) with poly(allylamine) (PAA). In this approach, Fe₃O₄ nanoparticles, prepared with diethanolamine (DEA) as the surface capping agent in diethyleneglycol (DEG) and methanol, are ligand exchanged with PAA. This method allows the dispersing of magnetic nanoparticles into individual or small clusters of 2–5 nanoparticles in aqueous solutions. The resulting nanoparticles are water soluble and stable for months. The PAA stabilized Fe₃O₄ nanoparticles are characterized by TEM, TGA, and FT-IR. The PAA-coated Fe₃O₄ nanoparticles will allow further chemical tailoring and engineering of their surfaces for biomedical applications.