A nanocomposite consisting of polyaniline and multiwalled carbon nanotubes was tethered with a thiolated thrombin-specific aptamer and placed on a glassy carbon electrode (GCE) to obtain a biosensor for thrombin that has a limit of detection of 80 fM. Tethering was accomplished via a thiol-ene reaction between thiolated thrombin aptamer (TTA) and oxidized polyaniline (PANI) that was chemically synthesized in the presence of solution-dispersed multiwalled carbon nanotubes (MWCNTs). The modified GCE exhibits a pair of well-defined redox peaks (at 50/?25 mV) of self-doped PANI in neutral solution, and the tethered TTA-thrombin interaction gives a decreased electrochemical signal. Cyclic voltammetry, scanning electron microscopy and ultraviolet visible spectroscopy were used to characterize the film properties. This amperometric aptasensor is sensitive, selective and reproducible. It was applied to the determination of thrombin in spiked human serum (0.2 to 4 nM) and gave recoveries that ranged from 95 to 102%.
Graphical abstract A nanocomposite consisting of polyaniline (PANI) and multiwalled carbon nanotubes (MWCNTs) was tethered with a thiolated thrombin aptamer (TTA) and placed on a glassy carbon electrode (GCE) to obtain a biosensor for thrombin that has a 80 f. detection limit.
An electrochemiluminescent (ECL) aptamer based method is described for the determination of thrombin. Three-dimensional nitrogen-doped graphene oxide (3D-NGO) was placed on a glassy carbon electrode (GCE) to provide an electrode surface that displays excellent electrical conductivity and acts as a strong emitter of ECL. The modified electrode was further coated with chitosan via electrodeposition. Finally, the amino-modified aptamer was immobilized on the modified GCE. The interaction between thrombin and aptamer results in a decrease in ECL. The assay has a linear response in the 1 fM to 1 nM thrombin concentration range and a 0.25 fM lower detection limit (at an S/N ratio of 3). The method was applied to the determination of thrombin in spiked human plasma samples, and recoveries ranged between 94 and 105% (with RSDs of <3.6%). The calibration plot was recorded at potential and wavelength of fluorescence emission (wavelength:?445 nm; potential:?0 to -2 V).
Graphical abstract A bare glassy carbon electrode (GCE) does not display electrochemiluminescence (ECL). If, however, nitrogen-doped graphene quantum dots, chitosan, and three-dimensional nitrogen-doped graphene oxide (NGQD-chitosan/3D-NGO) are electrodeposited on the GCE, strong ECL can be observed. The ECL intensity decreased after aptamer and bovine serum albumin (BSA) were dropped onto the electrode (curve a). However, the ECL further decreases after addition of thrombin (TB; curve b).
The authors describe an electrochemical sensor for hydrogen peroxide (H2O2). It was constructed by consecutive, selective modification of a glassy carbon electrode (GCE) with Prussian Blue (PB), layered molybdenum disulfide (MoS2), and reduced graphene oxide (rGO). The properties of the modified GCE were characterized via high-resolution transmission electron microscopy, UV-vis spectroscopy and X-ray diffraction. The electrochemical properties of the electrode were studied using cyclic voltammetry and electrochemical impedance spectroscopy. The sensor exhibits excellent electrocatalytic activity for the reduction of hydrogen peroxide in comparison to GCEs modified with MoS2-rGO or PB only. Response is linear in the 0.3 μM to 1.15 mM H2O2 concentration range at a working analytical voltage of 0.1 V, with a 0.14 μM detection limit. The electrochemical sensitivity is 2883.5 μA·μM?1·cm?2, and response is fast (<10 s). The sensor is selective, stable and reproducible. This is attributed to the efficient electron transport properties of the MoS2-rGO composite and the high loading with PB.
Graphic abstract Prussian Blue nanoparticles were deposited on MoS2-rGO modified glassy carbon electrode by electrochemical method. This sensor was used for the detection of H2O2 in tap water and river water.
An electrochemical nanoaptasensor is described that is based on the use of a glassy carbon electrode (GCE) modified with electrodeposited silver nanoparticles (AgNPs). An aptamer (Apt) against trinitrotoluene (TNT) was then immobilized on the AgNPs. The addition of TNT to the modified GCE leads to decrease in peak current (typically measured at a potential of ?0.45 V vs. Ag/AgCl) of riboflavin which acts as an electrochemical probe. Even small changes in the surface (as induced by binding of Apt to TNT) alter the interfacial properties. As a result, the LOD is lowered to 33 aM, and the dynamic range extends from 0.1 fM to 10 μM without sacrificing specificity.
Graphical abstract Schematic presentation of a nanoaptasensor which is based on a glassy carbon electrode (GCE) modified with electrodeposited silver nanoparticles (AgNPs) and aptamer (Apt). It was applied to the detection of 2,4,6-trinitrotoluene (TNT) with the help of riboflavin (RF) as a redox probe.
We describe a chemical exfoliation method for the preparation of MoS2 nanosheets. The nanosheets were incorporated into poly(3,4-ethylenedioxythiophene) (PEDOT) by electrodeposition on a glassy carbon electrode (GCE) to form a nanocomposite. The modified GCE is shown to enable simultaneous determination of ascorbic acid (AA), dopamine (DA) and uric acid (UA). Due to the synergistic effect of MoS2 and PEDOT, this electrode displays better properties in terms of electrocatalytic oxidation of AA, DA and UA than pure PEDOT, which is illustrated by cyclic voltammetry and differential pulse voltammetry (DPV). Under optimum conditions and at pH 7.4, the respective sensitivities and best working potentials are as follows: AA: 1.20 A?mM?1?m?2, 30 mV; DA: 36.40 A?mM?1?m?2, 210 mV; UA: 105.17 A?mM?1?m?2, 350 mV. The calculated detection limits for AA, DA and UA are 5.83 μM, 0.52 μM and 0.95 μM, respectively. The modified electrode was applied to the detection of the three species in human urine samples and gave satisfactory results.
Graphical abstract MoS2 nanosheets were prepared by a facile chemical exfoliation method. MoS2 and poly(3,4-ethylenedioxythiophene) nanocomposite modified glassy carbon electrodes were fabricated, which are shown to enable simultaneous determination of ascorbic acid, dopamine and uric acid with high sensitivity and selectivity.
A glassy carbon electrode (GCE) modified with polymeric nanocomposite consisting of palladium nanoparticles and a conductive polymeric ionic liquid was prepared. The modified GCE was applied to sensitive and fairly selective electrochemical determination of the mycotoxin zearalenone. Electrocatalytic oxidation is performed in a solution containing 20 % (V/V) acetonitrile and 80 % (V/V) of 1 M perchloric acid. Cyclic voltammetry and square wave voltammetry revealed a well-defined electrocatalytic peak current at overpotential of +0.69 V versus Ag/AgCl. Under optimized experimental conditions, there is a linear relationship between anodic peak current and zearalenone concentration in the range from 0.03 to 35 ng?mL￣1, and the detection limit is 0.01 ng?mL￣1. The method was successfully applied to the analysis of zearalenone in spiked food samples and gave recoveries between 95.6 and 104.0 %.
Graphical abstract The nanocomposite (PdVC-PIL) was prepared by polymerization of ionic liquid monomer (PIL) in presence of Pd nanoparticles on Vulcan XC-72R carbon (PdVC). The solution containing nanocomposite was placed on the glassy carbon electrode (GCE). The voltammetry activity of modified electrode (PdVC-PIL/GCE) was compared to a bare GCE for zearalenone determination.
The authors describe an electrochemical approach for the preparation of a glassy carbon electrode (GCE) modified with graphene oxide and silver nanodentrites (AgNDs). The coating was obtained by using an aqueous solution containing silver nitrate, phosphate and ammonia. The phosphate anions act as a scaffold for the improved deposition of AgNDs. The effects of deposition potential and time and concentration of electrolyte on the formation of the AgNDs were optimized. The modified GCE displays good electrocatalytic activity towards the oxidation of dissolved hydrazine. The electron transfer coefficient and diffusion coefficient are 0.60 and 4.64 × 10?5 cm2 s?1 respectively. The electrode exhibits a linear response over the 100 nM to 670 μM hydrazine concentration range and a detection limit (LOD) of 33 nM. The sensitivity of the modified electrode is 2077 μA mM?1 cm?2 at a typical working voltage of 0.1 V (vs Ag/AgCl). This LOD is much lower than that of the allowable concentration of hydrazine in drinking water as defined by the US EPA and the WHO.
Graphical abstract Schematic of the 2-step fabrication of a glassy carbon electrode (GCE) modified with graphene oxide (GO) and silver nanodendrites (AgND) for use in a hydrazine sensor. First, Ag3PO4 is formed by adding AgNO3 and phosphate. Secondly, the formed Ag3PO4 is converted to a colorless complex by adding ammonia and by electrolytic growth of AgND on the GO/GCE.
The authors describe a voltammetric immunosensor with antibody immobilized on a glassy carbon electrode (GCE) modified with N-doped graphene (N-GS), electrodeposited gold nanoparticles (AuNPs) and chitosan (Chit). The preparation is simple and the thickness of the electrodeposited films can be well controlled. Due to the specific advantages of N-GS, AuNPs and Chit, the electrode has a large specific surface, improved conductivity, high stability. A new label-free immunosensor for the model antigen (alpha fetoprotein, AFP) detection was then designed by employing N-GS-AuNP-Chit as the antibody immobilization and signal amplification platform. Differential pulse voltammetry and electrochemical impedance spectroscopy were used for the characterization of the stepwise assembly process. Under the optimized conditions, at a typical working potential of +0.20 V (vs. SCE), and by using hexacyanoferrate as an electrochemical probe, the immunosensor has a detection limit as low as 1.6 pg mL?1 and a linear analytical range that extends from 5 pg mL?1 to 50 ng mL?1. AFP was quantified in spiked human serum samples with acceptable precision.
Graphical Abstract Schematic of sensitive and effective label-free electrochemical immunosensor for the detection of AFP based on N-GS-AuNP-Chit as signal amplification matrix.
The authors describe a method for signal amplification in electrochemical aptasensors. It is based on the induction of an increased electrochemical current by the aptamer captured on a glassy carbon electrode (GCE). The phosphate groups on the aptamer backbone are brought to reaction with added molybdate to form a redox-active molybdophosphate precipitate on the surface of the GCE that generates a strong electrochemical current. To further enhance sensitivity, gold nanorods (GNRs) were selected as a support for the immobilization of aptamers. The aptasensor was applied to the determination of the cancer biomarker carcinoembryonic antigen (CEA) in a sandwich format. Antibody against CEA, CEA (antigen) and GNRs modified with CEA aptamer were sequentially captured on the GCE. The resulting aptasensor, best operated at a voltage as low as 0.18 V vs. Ag/AgCl, is highly sensitive and has a wide linear range that extends from 0.1 pg·mL?1 to 10 ng·mL?1 of CEA. This amplification strategy uses an aptamer as both the recognition probe and signal probe and therefore simplifies signal transduction. Conceivably, this detection scheme may be adapted to numerous other electrochemical bioassays if respective antibodies and aptamers are available.
Graphical abstract Schematic presentation of an electrochemical aptasensor based on aptamer induced electrochemical current for the detection of cancer biomarker carcinoembryonic antigen (CEA). Gold nanorods (GNR) are chosen for the immobilization of aptamers to increase the loading of aptamers.
This article reports on a novel aptamer-based platform for the quantitation of urea by using an aptamer with high affinity and selectivity for urea. The surface of a glassy carbon electrode (GCE) was modified by drop casting a cocktail consisting of carbon nanotubes and reduced graphene oxide (rGO) decorated with platinum-gold nanoparticles. The urea aptamer was then immobilized on the nanocomposite via covalent conjugation. Cyclic voltammetry and electrochemical impedance spectroscopy were employed to trace the modification of the GCE. Binding of urea caused the aptamer to be folded, and this result in an inhibition of the interfacial charge transfer rate when using hexacyanoferrate as an electrochemical redox probe. The change in redox current was quantified by differential pulse voltammetry, typically at a working voltage of 0.22 V vs. Ag/AgCl. The assay has a 1.9 pM detection limit, and the response is linear up to 150 nM concentration of urea. The superior selectivity and affinity of aptamer-modified GCE makes it a most useful tool for analysis of urea present in very low concentrations.
A composite material obtained by ultrasonication of graphene oxide (GO) and multi-walled carbon nanotubes (MWCNTs) was loaded with manganese dioxide (MnO2), poly(diallyldimethylammonium chloride) and gold nanoparticles (AuNPs), and the resulting multilayer hybrid films were deposited on a glassy carbon electrode (GCE). The microstructure, composition and electrochemical behavior of the composite and the modified GCE were characterized by transmission electron microscopy, Raman spectra, energy-dispersive X-ray spectroscopy, electrochemical impedance spectroscopy and cyclic voltammetry. The electrode induces efficient electrocatalytic oxidation of dopamine at a rather low working voltage of 0.22 V (vs. SCE) at neutral pH values. The response is linear in the 0.5 μM to 2.5 mM concentration range, the sensitivity is 233.4 μA·mM￣1·cm￣2, and the detection limit is 0.17 μM at an SNR of 3. The sensor is well reproducible and stable. It displays high selectivity over ascorbic acid, uric acid and glucose even if these are present in comparable concentrations.
Graphical abstract Gold nanoparticles were self-assembled onto the surface of the MnO2 decorated graphene oxide-carbon nanotubes composites with poly(diallyldimethylammonium chloride) (PDDA) as a coupling agent. Further, a sensitive electrochemical sensor of dopamine was developed via immobilizing this nanocomposite on a glassy carbon electrode (GCE).
Polyimide (PI) sheets were laser etched to obtain graphene-based carbon nanomaterials (LEGCNs). These were analyzed by scanning electron microscopy, X-ray diffraction and Raman spectroscopy which confirmed the presence of stacked multilayer graphene nanosheets. Their large specific surface and large number of edge-plane active sites facilitate the accumulation of metal ions. A glassy carbon electrode (GCE) with an in-situ plated bismuth film was modified with the LEGCNs to give a sensor with satisfactory response for the simultaneous determination of cadmium(II) and lead(II) by means of square wave anodic stripping voltammetry. It appears that is the first report on an electrochemical sensor based on the use of laser etched graphene for determination of heavy metal ions. Figures of merit for detection of Cd(II) include (a) a low and well separated working potential of ?0.80 V (vs. Ag/AgCl), (b) a wide linear range (from 7 to 120 μg·L?1), and a low detection limits 0.47 μg·L?1. The respective data for Pb(II) are (a) -0.55 V, (b) 5 to 120 μg·L?1, and (c) 0.41 μg·L?1. The modified GCE displays remarkable repeatability, reproducibility, selectivity and stability. The sensor was applied to the simultaneous determination of Cd(II) and Pb(II) in spiked real water samples. The results confirm that the laser etching technique is an efficient tool for the preparation of carbon nanomaterials with high quality and great sensing performance.
Graphical abstract Bismuth film and laser etched graphene-modified glassy carbon electrode (BF-LEGCN/GCE) for the simultaneous determination of cadmium(II) and lead(II) by square wave anodic stripping voltammetry.
An aptamer based method is described for the electrochemical determination of ampicillin. It is based on the use of DNA aptamer, DNA functionalized gold nanoparticles (DNA-AuNPs), and single-stranded DNA binding protein (ssDNA-BP). When the aptamer hybridizes with the target DNA on the AuNPs, the ssDNA-BP is captured on the electrode surface via its specific interaction with ss-DNA. This results in a decreased electrochemical signal of the redox probe Fe(CN)63? which is measured best at a voltage of 0.188 mV (vs. reference electrode). In the presence of ampicillin, the formation of aptamer-ampicillin conjugate blocks the further immobilization of DNA-AuNPs and ssDNA-BP, and this leads to an increased response. The method has a linear reposne that convers the 1 pM to 5 nM ampicillin concentration range, with a 0.38 pM detection limit (at an S/N ratio of 3). The assay is selective, stable and reproducible. It was applied to the determination of ampicillin in spiked milk samples where it gave recoveries ranging from 95.5 to 105.5%.
Graphical abstract Schematic of a simple and sensitive electrochemical apta-biosensor for ampicillin detection. It is based on the use of gold nanoparticles (AuNPs), DNA aptamer, DNA functionalized AuNPs (DNA-AuNPs), and single-strand DNA binding protein (SSBP).
Three-dimensional structures comprising polypyrrole nanowires (PPyNWs) and molecularly imprinted polymer (MIP) were prepared by electropolymerization on the surfaces of a glassy carbon electrode (GCE). The modified GCE possesses both large surface area and good electrocatalytic activity for oxidizing dopamine (DA), and this leads to high sensitivity. The electropolymerized MIP has a large number of accessible surface imprints, and this makes the GCE more selective. Under optimal conditions and at a working voltage of typically 0.23 V (vs. SCE), the calibration plot is linear in the 50 nM to 100 μM DA concentration range, and the limit of detection is 33 nM. The sensor has been successfully applied to the analysis of DA in injections.
Graphical abstract Schematic of a three-dimensional nanocomposite based dopamine sensing platform based on the use of a molecularly imprinted polymer and poly(pyrrole) nanowires. The modified polypyrrole nanowires and molecularly imprinted polymer endowed high electrocatalytic capacity and good selectivity for dopamine recognition, respectively.
A metal organic framework (MOF) of the type copper(II)-1,3,5-benzenetricarboxylic acid (Cu-BTC) was electrodeposited on electroreduced graphene oxide (ERGO) placed on a glassy carbon electrode (GCE). The modified GCE was used for highly sensitive electrochemical determination of 2,4,6-trinitrophenol (TNP). The fabrication process of the modified electrode was characterized by scanning electron microscopy and electrochemical impedance spectroscopy. Differential pulse voltammetry (DPV) demonstrates that the Cu-BTC/ERGO/GCE gives stronger signals for TNP reduction than Cu-BTC/GCE or ERGO/GCE alone. DPV also shows TNP to exhibit three reduction peaks, the first at a potential of ?0.42 V (vs. SCE). This potential was selected because the other three similarly-structured compounds (2-nitrophenol, 4-nitrophenol, 2,4-dinitrophenol) do not give a signal at this potential. Response is linear in the 0.2 to 10 μM TNP concentration range, with a 0.1 μM detection limit (at S/N =?3) and a 15.98 μA?μM?1?cm?2 sensitivity under optimal conditions. The applicability of the sensor was evaluated by detecting TNP in spiked tap water and lake water samples. Recoveries ranged between 95 and 101%.
Graphical abstract Schematic presentation of an electrochemical sensor that was fabricated by electrodeposition of the metal-organic framework (MOF) of copper(II)-1,3,5-benzenetricarboxylic acid (Cu-BTC) onto the surface of electroreduced graphene oxide (ERGO) modified glassy carbon electrode (GCE). It was applied to sensitive and selective detection of 2,4,6-trinitrophenol (TNP).
The authors describe an immunoassay for the determination of carcinoembryonic antigen (CEA) tumor markers by depositing a polydopamine-Pb(II) nanocomposite on the surface of a glassy carbon electrode. The nanocomposite acts as a redox system that displays a large specific surface and provides a strong current signal at ?0.464 V (vs. Ag/AgCl). After the deposition of PDA-Pb2+ on glassy carbon electrode, the electrode was additionally coated with a chitosan-gold nanocomposite. The immunoassay platform was obtained by immobilization of antibodies against carcinoembryonic antigens by using glutaraldehyde and blocking with bovine albumin. Owing to its large surface, good electrical conductivity and powerful current response, the immunoassay has a wide linear range that extends from 1 fg·mL?1 to 100 ng·mL?1, with a detection limit as low as 0.26 fg·mL?1. The results obtained with this immunoassay when determining CEAs in human serum were found to be consistent with those obtained by ELISAs.
Graphical abstract Schematic of an ultrasensitive electrochemical immunosensor for the carcinoembryonic antigen. It is based on a glassy carbon electrode modified with a polydopamine-Pb(II) nanocomposite acting as a signal-inherent substrate.
A highly selective electrochemical sensor was fabricated based on a modified carbon paste electrode with zinc ferrite nanoparticles (ZnFe2O4 NPs). The nanocomposite has attractive properties such as high surface-to-volume ratio and good electrocatalytic activity towards the drugs acetaminophen (AC), epinephrine (EP), and melatonin (MT), best at working voltages of 0.35, 0.09 and 0.55 V (vs. Ag/AgCl), respectively. The linear ranges (and detection limits) are 6.5–135 (0.4) μmol L?1 for AC, 5–100 (0.7) μmol L?1 for EP, and 6.5–145 (3) μmol L?1 for MT.
Graphical abstract A novel electrochemical sensor based on a modified carbon paste electrode with zinc ferrite nanoparticles (ZnFe2O4) for the simultaneous detection of the acetaminophen, epinephrine and melatonin was fabricated
A new type of manganese diselenide nanoparticles (MnSeNPs) was synthesized by using a hydrothermal method. Their surface morphology, crystallinity and elemental distribution were characterized by using transmission electron microscopy, X-ray diffraction, energy dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy which scrutinize the formation of the NPs. The NPs were coated on a glassy carbon electrode (GCE), and electrochemical impedance spectroscopy, cyclic voltammetry and differential pulse voltammetry were applied to study the electroanalytical properties towards the oxidation of the food additive capsaicin. The modified GCE displays lower charge transfer resistance (Rct?=?29.52 Ω), a larger active surface area (0.089 cm2/g, and more efficient electrochemical oxidation of capsaicin compared to a MnS2/GCE and a bare GCE. The oxidation peak potential is 0.43 V (vs. Ag/AgCl) which is lower than that of previously reported GCEs. The sensor has a detection limit as low as 0.05 μM and an electrochemical sensitivity of 2.41 μA μM?1 cm?2. The method was applied to the determination of capsaicin in pepper samples.
The authors describe a dual signal amplification strategy for improving the sensitivity of electrochemical aptasensor. Hydroxyapatite nanoparticles (HAP-NPs) serve as the support for deposition of the respective aptamer. Both the HAP-NPs and the aptamer contain phosphate groups which can react with molybdate to form a redox-active molybdophosphate precipitate on the surface of a glassy carbon electrode (GCE). On applying a relatively low voltage of 0.21 V (vs. Ag/AgCl), a current is generated whose intensity depends on the concentration of the analyte. The cancer biomarker platelet-derived growth factor BB (PDGF-BB) is chosen as a model antigen (analyte). The assay works by sequential deposition of antibody against PDGF-BB, analyte (PDGF-BB) and anti-PDGF-BB aptamer modified HAP-NPs on the GCE to form a sandwich structure. The amperometric signal is linear in the 0.1 pg.mL?1 to 10 ng.mL?1 PDGF-BB concentration range, with a detection limit as low as 50 fg.mL?1. The assay was successfully applied to the determination of PDGF-BB in serum samples. In our perception, this signal amplification strategy has a wide scope in that it can be adapted to the preparation of other aptasensors for biomarkers and related species.
Graphical abstract Schematic of an electrochemical aptasensor based on dual signal amplification strategy. It was applied to the detection of cancer biomarker platelet-derived growth factor BB (PDGF-BB). Hydroxyapatite (HAP) nanoparticles were chosen for the immobilization of aptamers to increase the loading of aptamers.
Core-shell Au@Ag nanorods (Ag@GNRs) were synthesized and utilized to construct a voltammetric biosensor for trichloroacetic acid (TCA). The biosensor was prepared by immobilizing hemoglobin (Hb) on a glassy carbon electrode (GCE) that was modified with the Ag@GNRs. Cyclic voltammetry revealed a pair of symmetric redox peaks, indicating that direct electron transfer occurs at the Hb on the Ag@GNR-film. The electron transfer rate constant is as high as 2.32 s?1. The good electrocatalytic capability and large surface area of the Ag@GNR-film is beneficial in terms of electron transfer between Hb and the underlying electrode. The modified GCE, best operated at ?0.4 V (vs. SCE), exhibits electrocatalytic activity toward TCA in the 0.16 μM to 1.7 μM concentration range, with a 0.12 μM detection limit (at an S/N ratio of 3).
Graphical abstract Core-shell Au@Ag nanorods (Ag@GNRs) were synthesized and used to immobilize hemoglobin to construct an effective biosensor for trichloroacetic acid.
