Fabrication of TiO2 Grating with Composites of Azobenzene Polymer and TiO2 Nanoparticles

We have used the formation of surface relief gratings (SRG) on azobenzene polymers to manipulate TiO₂ nanoparticles and to fabricate TiO₂ nanoparticle gratings. Suspensions of an azobenzene polymer (PDO3) and TiO₂ were used to spin coat thin films on glass slide substrates. By interfering coherent light from an Argon laser on the surface of the PDO3‐TiO₂ composite films, SRGs were fabricated. Atomic force microscopic images of the SRGs show TiO₂ nanoparticles dispersed throughout the sample, and in particular, at the peaks of the SRG after oxygen plasma treatment. The lateral forces acting on the azobenzene polymer during the SRG fabrication drag the TiO₂ nanoparticles. These results indicated that it is feasible to create TiO₂ nanoparticle gratings with the composites.     

PHOTOINDUCED SURFACE RELIEF GRATINGS ON AZOCELLULOSE FILMS

Surface relief gratings (SRG) on films of azobenzene–modified cellulose (azocellulose) with ultrahigh molecular weight were holographically recorded in a single step. Surface modulation depth of the SRGs increased with the degree of substitution (DS) of the azobenzene chromophores in the cellulose as well as with the grating spacing. Large surface modulations over 500 nm on all samples were obtained with a grating spacing of 4 μm. A linear increase of photoinduced birefringence with the azobenzene chromophore concentration in these photodynamic polymers was also observed. The maximum birefringence of 0.11 was achieved for an azocellulose polymer with a DS of 0.99.

     

Alignment control of liquid crystals on surface relief gratings

Liquid crystal alignment layers of a high T _g polymer containing an azobenzene moiety are prepared by photofabrication of a surface relief grating (SRG). The interference pattern of a circular and linearly polarized Ar⁺ laser beam generated the surface relief grating and the morphology was detected by atomic force microscope. The optical anisotropy of the films was investigated by polarizing optical microscopy. The orientation of the optical axis of the film mainly depends on the direction of the initial polarization plane. Nematic liquid crystals were aligned parallel to the direction of the grating, but the pretilt angles of the liquid crystals were nearly zero. Irradiation with homogeneous linearly polarized light could also align liquid crystals, but this alignment capability was weaker than that of the SRG film.     

表面起伏光栅形成速率的影响规律 Ⅰ.偶氮生色团种类和官能度的影响

设计并合成了含有不同生色团以及不同官能度的环氧树脂基偶氮高分子 ,系统研究了偶氮生色团的种类和官能度对光栅形成速率的影响规律 .实验结果表明 ,偶氮苯对位是羧基的聚合物的光栅形成速率明显快于偶氮苯对位是硝基的聚合物 ,光栅形成速率随偶氮生色团官能度的增加而加快 .这两类聚合物都可以形成规整的可擦式表面起伏光栅     

Polarization holographic grating recording in the cholesteric azobenzene‐containing films with the phototunable helix pitch

The recording of polarization gratings in films of a cholesteric liquid crystalline polymer with different helix pitch was studied in detail. For this purpose, the cholesteric mixture of the nematic azobenzene‐containing copolymer with a chiral‐photochromic dopant was prepared. The utilization of such mixture has made possible to realize dual optical photorecording in one system, first due to the phototuning of the helix pitch by UV light and second the polarization grating recording process by exposure with polarized visible light. The diffraction efficiency strongly depends on the cholesteric helix pitch and films thickness: the increase of the confinement ratio d/p (where d, film thickness; p, helix pitch) results in growth of the diffraction efficiency. Comparison of the induction of polarization gratings in cholesteric, nematic (copolymer without chiral dopant), and amorphous (nonannealed) cholesteric films revealed that only the cholesteric films were characterized by significant oscillations in the diffraction efficiency signal as well as by the presence of the maximum in the first‐order diffraction efficiency in the initial stage of the grating recording process. It was found that in addition to the polarization grating surface relief gratings (SRGs) were also formed in the studied systems, however, the amplitude of the SRG inscribed in the cholesteric films was lower (～20 nm) compared to the grating amplitude obtained in nematic films (～60 nm). Moreover, increasing helix pitch resulted in a decrease of the SRG amplitude. The obtained experimental data demonstrate the great potential of cholesteric LC mixtures of such type for different applications as photoactive materials for photonics. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 773–781     

Controllable alignment of liquid crystals based on the surface relief gratings from a photocross-linkable organic monomer

The orientational control of liquid crystal (LC) molecules is essential for high-quality liquid crystal displays, and the photo-induced surface relief grating (SRG) is a facile and effective non-contact process. Here, SRGs with different period and depth were prepared with a photocross-linkable organic monomer 4-propyldiphenylacetylenecarboxylic acid cinnamyl ester (PDACE), and the LC alignment induced by SRG was studied. It is found that both the surface topography and the chemical nature of the surface are responsible for the LC alignment, which is strongly dependent on the groove geometry of the gratings. Furthermore, the patterned LC cell was fabricated with the patterned SRG surface. These results demonstrate that the planar, perpendicular and patterned orientations of LC can be easily photo-controllably obtained with PDACE, which have important applications in optical devices.     

Alignment control of liquid crystals on surface relief gratings

Liquid crystal alignment layers of a high T_g polymer containing an azobenzene moiety are prepared by photofabrication of a surface relief grating (SRG). The interference pattern of a circular and linearly polarized Ar⁺ laser beam generated the surface relief grating and the morphology was detected by atomic force microscope. The optical anisotropy of the films was investigated by polarizing optical microscopy. The orientation of the optical axis of the film mainly depends on the direction of the initial polarization plane. Nematic liquid crystals were aligned parallel to the direction of the grating, but the pretilt angles of the liquid crystals were nearly zero. Irradiation with homogeneous linearly polarized light could also align liquid crystals, but this alignment capability was weaker than that of the SRG film.     

Fabrication of fluorescent holographic micropatterns based on the rare earth complexes using azobenzene‐containing poly(aryl ether)s as macromolecular ligands

In this work, on the basis of photoinduced surface relief gratings (SRGs) with the rare earth complexes using azo‐polymers as macromolecular ligands, a series of novel materials for fabricating rewritable fluorescent two‐dimensional micropatterns, whose color can be easily adjusted by changing the species of the rare earth ions, are demonstrated. The rare earth complexes are prepared using a series of poly(aryl ether)s containing azobenzene chromophores and carboxyl group as macromolecular ligands and 1,10‐phenanthroline as co‐ligands. The fluorescence properties of the rare earth complexes and the influence of the contents of azobenzene chromophores on the fluorescent intensity are investigated by means of fluorescence excitation and emission spectroscopy. By exposing the films of the rare earth complexes to an interference pattern laser beam, SRGs can be formed on the films. Under the excitation, fluorescent patterns of the SRGs can be observed by the measurement of fluorescence microscopy. © 2015 Wiley Periodicals, Inc. J. Polym. Sci. Part A: Polym. Chem. 2015 , 53, 936–943     

BIOLOGICALLY DERIVED PHOTOACTIVE MACROMOLECULAR AZODYES

Azophenols with various substituents at the para position of the phenyl ring were enzymatically polymerized in the presence of H₂O₂. Structural characterization of the synthesized polymers by FTIR, FT-Raman, and NMR (¹H and ¹³C) spectroscopy confirms our previous observation that this enzymatically catalyzed coupling reaction occurs primarily at the ortho positions, with some substitution at the meta position of the phenol ring. The strong constraint and poor packing of the azobenzene chromophores in the polymer leads to a significant blue shift of the π-π^* transition absorption and slow photoisomerization and thermal relaxation in comparison to the monomers. Surface relief gratings (SRG) with large surface modulation have been fabricated on these enzymatically synthesized polymer films.

     

QM/MM Studies on Photoisomerization Dynamics of Azobenzene Chromophore Tethered to a DNA Duplex: Local Unpaired Nucleobase Plays a Crucial Role

The photoresponsive azobenzene‐tethered DNAs have received growing experimental attention because of their potential applications in biotechnology and nanotechnology; however, little is known about the initial photoisomerization of azobenzene in these systems. Herein we have employed quantum mechanics/molecular mechanics (QM/MM) methods to explore the photoisomerization dynamics of an azobenzene‐tethered DNA duplex. We find that in the S₁ state the trans–cis photoisomerization path is much steeper in DNA than in vacuo, which makes the photoisomerization much faster in the DNA environment. This acceleration is primarily caused by complex steric interactions between azobenzene and the nearby unpaired thymine nucleobase, which also change the photoisomerization mechanism of azobenzene in the DNA duplex.     

Core level studies of calcite and dolomite

Conventional X‐ray photoelectron spectroscopy (XPS) and synchrotron‐based X‐ray photoelectron spectroscopy (HRXPS) have been used to study Iceland spar calcite (CaCO₃) and dolomite (CaMg(CO₃)₂). The obtained full widths at half maximum (FWHMs) are mostly narrower than in the previous results, which together with the symmetry of the fitted peaks indicate effective neutralisation of surface charging. Some previously unidentified features observed in the Ca 2p, C 1s and O 1s spectra of calcite have been suggested to be bulk plasmons. Also, surface core level shifts in Ca 2p (in calcite) and Mg 2p (in dolomite) spectra have been obtained and found to be consistent between XPS and HRXPS measurements. A peak attributed to carbide (CaC₂) has been suggested to indicate beam‐assisted interaction with hydrocarbons found on the surface. Copyright © 2014 John Wiley & Sons, Ltd.     

可溶性聚酰亚胺类偶氮高分子的合成与表征

用聚合物的后重氮偶合方法合成了以可溶性聚酰亚胺为主链 ,偶氮生色团为侧基的新型偶氮高分子 ,并通过引入线性长链烷烃侧基来提高聚合物的溶解性 .采用红外光谱、氢核磁共振、紫外光谱和热分析等手段 ,对产物的结构、热性能及光学性能等进行了表征 .该聚合物膜在氩离子干涉激光的照射下形成正弦波形的表面起伏光栅 ,起伏深度可达 2 0 0nm .     

Effects of nitrogen composition on the resistivity of reactively sputtered TaN thin films

Nanocrystalline tantalum nitride (TaN) thin films have been deposited by reactive direct current magnetron sputtering technique on Si/SiO₂ (100) substrate with nitrogen flow rate ranging from 0, 3, 5, 7, 9 to 11 standard cubic centimeter per minute (sccm). Structural properties, surface morphology, chemical composition and and resistivity of the TaN films were investigated by X‐ray diffraction (XRD), field emission scanning electron microscopy, X‐ray photoemission spectroscopy (XPS) and four‐point probe measurements, respectively. In the XRD spectra, a classical formation sequence of tantalum nitride phases in the order of Ta‐Ta₂N‐TaN‐Ta₄N₅ and decreasing amount of metallic Ta were observed with increasing nitrogen flow. The electrical resistivity of the TaN film was found to increase with increasing N/Ta ratio as a result of the increased electron scattering from interstitial N atoms. In the XPS analysis, two groups of Ta4f doublets relating to different TaN phases were observed in the core level spectra of TaN films. No strong coupling was observed between the Ta4f doublets and the Ta4p and the N1s groups. The appropriate nitrogen flow was believed to be helpful in the bonding and formation of stoichiometric TaN. Copyright © 2014 John Wiley & Sons, Ltd.     

Nanoscale Chemical Imaging of Reversible Photoisomerization of an Azobenzene‐Thiol Self‐Assembled Monolayer by Tip‐Enhanced Raman Spectroscopy

An understanding of the photoisomerization mechanism of molecules bound to a metal surface at the molecular scale is required for designing photoswitches at surfaces. It has remained a challenge to correlate the surface structure and isomerization of photoswitches at ambient conditions. Herein, the photoisomerization of a self‐assembled monolayer of azobenzene‐thiol molecules on a Au surface was investigated using scanning tunneling microscopy and tip‐enhanced Raman spectroscopy. The unique signature of the cis isomer at 1525 cm^?1 observed in tip‐enhanced Raman spectra was clearly distinct from the trans isomer. Furthermore, tip‐enhanced Raman images of azobenzene thiols after ultraviolet and blue light irradiation are shown with nanoscale spatial resolution, demonstrating a reversible conformational change. Interestingly, the cis isomers of azobenzene‐thiol molecules were preferentially observed at Au grain edges, which is confirmed by density functional theory.     

Synthesis of novel three‐arm star azo side‐chain liquid crystalline polymer via ATRP and photoinduced surface relief gratings

A three‐arm star azo side‐chain liquid crystalline (LC) homopolymer, poly[6‐(4‐methoxy‐4‐oxy‐azobenzene) hexyl methacrylate] (PMMAZO), was synthesized by atom transfer radical polymerization (ATRP) method. The polymerization of 6‐(4‐methoxy‐4‐oxy‐azobenzene) hexyl methacrylate proceeded in a controlled/“living” way. A series of three‐arm star LC block copolymers (PMMAZO‐b‐PMMA) were also synthesized. The polymers were characterized by ¹H NMR, gel permeation chromatograph, and UV–vis spectra, respectively. The both polymers of PMMAZO and copolymers of PMMAZO‐b‐PMMA exhibited a smetic phase and a nematic phase. As concern to the PMMAZO, the glass‐transition temperature (T_g) and phase‐transition temperature from the smetic to nematic phase and from the nematic to isotropic phase increased with the increase of molecular weight (M_n(GPC)) of PMMAZO. The phase transition temperature of the block copolymers, PMMAZO‐b‐PMMA, with the same PMMA block was similar to that of PMMAZO. However, the T_g of the PMMAZO‐b‐PMMA decreased at low azo content and then increased with the increasing M_n(GPC) when azo content was above 61.3%. With illumination of linearly polarized Kr⁺ laser beam at modest intensities (35 mW/cm²), significant surface relief gratings formed on PMMAZO films with different molecular weights were observed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 777–789, 2008     

Behaviors of self‐assembled diblock copolymer with pendant photosensitive azobenzene segments

A novel monomer, ethyl 4‐[4‐(11‐methacryloyloxyundecyloxy)phenyl azobenzoyl‐oxyl] benzoate, containing a photoisomerizable N?N group was synthesized. The monomer was further diblock copolymerized with methyl methacrylate. Amphiphilic diblock copolymer poly(methyl methacrylate‐block‐ethyl 4‐[4‐(11‐methacryloyloxyundecyloxy)phenyl azobenzoyl‐oxyl] benzoate ( PMMA ‐ b ‐ PAzoMA ) was synthesized using atom transfer radical polymerization. The reverse micelles with spherical construction were obtained with 2 wt % of the diblock copolymer in a THF/H₂O mixture of 1:2. Under alternating UV and visible light illumination, reversible changes in micellar structure between sphere and rod‐like particles took place as a result of the reversible E‐Z photoisomerization of azobenzene segments in PMMA ‐ b ‐ PAzoMA . Microphase separation of the amphiphilic diblock copolymer in thin films was achieved through thermal and solvent aligning methods. The microphases of the annealed thin films were investigated using atom force microscopy topology and scanning electron microscopy analyses. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1142–1148, 2010     

Direct Fabrication of Nanodomes‐Combined Surface Relief Gratings on Azobenzene Polymer Films with Controlled Shapes and Sizes

In this study, we present nanodomes‐combined surface relief gratings (SRGs) of azopolymer films with controlled shapes and sizes. We investigate the effect of the polarization mode of light interference on leading nanodomes in the conventional SRG patterns. In addition, we also systematically study the relationship between Bragg distance of light interference and shapes of nanodomes. From this, we explain the anisotropic self‐assembled behavior nanodomes in photoaddressable azopolymer films regarding polarization modes as well as spatial confinement effect. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 731–737