功能化有序介孔碳对重金属离子Cu(II)、Cr(VI)的选择性吸附行为

以三嵌段共聚物F127为模板剂, 酚醛树脂为碳源, 正硅酸乙酯为硅源, 三组分共组装合成介孔碳?氧化 硅纳米复合物, 再经HF去除氧化硅, 得到有序介孔碳(OMC). X射线衍射(XRD)、透射电子显微镜(TEM)、低温 N2吸脱附(BET)等测试表明, 所得样品具有高度有序的介孔结构, 比表面积和孔容分别为1330 m²·g^-1和2.13 cm³·g^-1, 平均孔径6.4 nm. 对其先氧化、后氯化、再胺化, 得到不同胺基接枝量的胺化介孔碳(C-NH₂(m), m为加入的乙二胺的质量(g)). 傅里叶变换红外(FT-IR)光谱表征结果证实, 胺基官能团成功接枝到有序介孔碳表面.TEM测试表明介孔碳的有序孔道结构得到了较好的保持. 以有序介孔碳、胺化介孔碳作吸附剂对Cu(II)、Cr(VI)进行选择性吸附研究. 结果表明: 功能化修饰前, 样品对Cu(II)、Cr(VI)饱和吸附量分别为213.33、241.55 mg·g^-1; 修饰后饱和吸附量可分别达到495.05、68.21 mg·g^-1. 功能化介孔碳表现了较强的选择性吸附Cu(II)的能力.     

介孔α-Fe2O3表面配合反应平衡常数测定

采用十二胺为模板剂、氨水做沉淀剂成功制备了介孔α-Fe₂O₃, 通过粉末X射线衍射(XRD)、透射电镜(TEM)、N₂吸附/脱附技术对样品晶相、形貌和比表面积进行了表征. 根据介孔α-Fe₂O₃悬浮液的酸碱滴定数据, 使用FITEQL软件, 采用双电层恒电容模型计算得出了介孔α-Fe₂O₃的表面酸碱反应平衡常数. 在此基础上研究了Cu^2＋, Pb^2＋, Zn^2＋在介孔氧化铁表面的吸附行为, 使用WinSGW软件模拟得出了相应的表面配合反应平衡常数并讨论了其吸附机理.     

介孔氧化铝负载Ni-Co氧化物催化剂上丙烷氧化脱氢制丙烯

以非离子型三嵌段共聚物作为模板剂, 异丙醇铝为氧化铝的前驱物, 采用一锅法合成了一系列介孔氧化铝负载镍氧化物、钴氧化物以及镍-钴双金属氧化物催化剂, 并以介孔氧化铝为载体, 采用浸渍法制备了负载Ni-Co 氧化物催化剂. 采用N₂吸附-脱附、高分辨透射电镜(HRTEM)、X射线粉末衍射(XRD)、H₂程序升温还原(H₂-TPR)以及激光拉曼光谱(LRS)等技术对催化剂的结构与性质进行表征, 并考察了催化剂的丙烷氧化脱氢反应性能. 结果表明: 一锅法制备的各催化剂均有大的比表面积和规整的孔道结构, 且负载的金属氧化物高度分散; 而浸渍法制备的催化剂, 其载体的介孔结构被破坏并有Co₃O₄晶相生成. 在考察的催化剂中, 一锅法合成的介孔氧化铝负载Ni-Co 氧化物催化剂表现出最佳的丙烷氧化脱氢性能. 在450 °C、C₃H₈:O₂:N₂的摩尔比为1:1:4和空速(GHSV)为10000 mL·g^-1·h^-1条件下, 该催化剂上丙烯产率为10.3%, 远高于浸渍法制备的催化剂上所获得的丙烯产率(2.4%). 关联催化剂表征和反应结果, 讨论了催化剂结构与性能之间的关系.     

连续在线原位ATR-FTIR技术测定介孔CuAl2O4对黄药的吸附

以丁胺和正十二醇为混合模板剂, 采用共沉淀法制备了介孔纳米CuAl₂O₄. 用X射线粉末衍射(XRD)、傅里叶变换红外(FTIR)光谱、N₂吸附-脱附对产物的结构进行了表征. 采用连续在线原位衰减全反射傅里叶变换红外(ATR-FTIR)光谱技术研究了水溶液中丁基和辛基黄药在介孔CuAl₂O₄表面的吸附. 随着吸附时间的延长,1200 和1040 cm^-1两处黄药特征峰的高度逐渐增加, 根据1200 cm^-1处C-O-C伸缩振动峰的变化来评价黄药在CuAl₂O₄表面的吸附动力学过程. 结果表明, 介孔纳米CuAl₂O₄对黄药有很强的吸附能力, 在100 min 的时间内, CuAl₂O₄样品对丁基和辛基黄药的吸附量分别达到了236 和300 mg·g^-1, 且属于化学吸附. 对实验数据进行理论模拟, 发现吸附过程更接近于拟二级吸附动力学方程.     

污泥活性炭的结构特征及表面分形分析

以城市污水厂污泥为主要原料添加适量添加剂, 采用ZnCl₂化学活化法制备的污泥活性炭, 借助XRD, BET法, FT-IR, SEM等现代分析测试方法结合液相吸附法, 表征结构特征和分析表面分形维数. 结果表明: 在适宜的活化温度、活化时间、ZnCl₂浓度、原料粒度等工艺条件下, 加入少量添加剂制备的污泥活性炭, 最可几孔径分布在4.16 nm左右,平均孔容0.4484～0.5122 mL•g^－1, 比表面积为634.8～748 m²•g^－1, IR峰中出现C—OH, C—H, N＝O, C＝C功能组, 孔结构是具有平行壁的狭缝状介孔结构. 由液相吸附法得到的污泥活性炭分维近似为2, 属于低分维二维表面.     

介孔炭的孔结构对其负载的Ru基氨合成催化剂性能的影响

采用模板法合成了介孔炭(MC),研究了其孔结构对其负载的Ru基氨合成催化剂Ba-Ru-K/MC性能的影响,采用N₂吸附脱附、扫描电镜和透射电镜等手段对介孔炭的孔结构进行了表征.研究发现,介孔炭载体的孔结构取决于模板剂的用量,当SiO₂/C质量比为1.0时,所制介孔炭比表面积最大.介孔炭负载的Ba-Ru-K催化剂活性与其介孔比表面积相关.在425℃,10MPa和10000h^-1条件下,合成氨的反应速率为139mmol/(g_cat·h).     

MCM-41负载S2O82-/TiO2固体超强酸的制备和酯化性能研究

采用液相沉积法制备了由MCM-41介孔分子筛负载S₂O₈^2-/TiO₂的固体超强酸催化剂。探讨了成酸机理，并以乙酸和异戊醇的酯化反应作为探针反应考察了焙烧温度、浸渍溶液浓度等制备条件对催化剂催化活性的影响，得到了较佳的制备条件。XRD、N₂吸附-脱附和FTIR结果表明，固体超强酸保持了MCM-41的介孔结构，BET表面积高达211 m²·g^-1，且具有强酸性(H_o<-12.70)。     

有序介孔氧化硅膜的制备及结构研究

本文介绍了在α-Al₂O₃中空纤维载体上制备担载有序氧化硅膜的方法。应用LXRD、HRTEM、TG-DTA、SEM、氮气吸附等测试手段对膜的结构、形貌进行了表征。LXRD和HRTEM结果显示所制备的非担载膜具有高度有序的二维六方结构。SEM分析发现担载膜表面完整、无缺陷。气体渗透实验表明中空纤维担载膜具有一定的气体选择性，在0.1 MPa下对H₂/N₂和CH₄/N₂的分离因子分别为2.80和1.65，气体透过膜孔的扩散由努森机制所控制。等温氮气吸附实验显示：500 ℃热处理后非担载膜的比表面积为548.84 m²·g^-1，孔容为0.57 mL·g^-1。     

ZnCr双金属层状材料对废水中酸性红14的吸附性能

采用共沉淀法制备性能优异的层状材料锌铬水滑石(Zn_xCr-LDHs, x=2, 3, 4), 并探究各种因素对吸附酸性红14(AR14)的影响。XRD、ICP、FTIR及BET表征结果表明:合成的Zn_xCr-LDHs晶型良好且稳定, 具备介孔结构。实验结果表明:最佳吸附剂为Zn₃Cr-LDHs, 比表面积为101 m²·g^-1, 对AR14的最大吸附容量为484.63 mg·g^-1。同时, 降低溶液pH值和提高溶液温度均可促进AR14的吸附。该吸附过程分别符合准二级动力学模型和Freundlich等温吸附模型。结合Materials Studio 5.5软件模拟, 推测该吸附机理主要以表面吸附为主, -SO₃^-基团是反应点。     

ZnCr双金属层状材料对废水中酸性红14的吸附性能

采用共沉淀法制备性能优异的层状材料锌铬水滑石(Zn_xCr-LDHs, x=2, 3, 4), 并探究各种因素对吸附酸性红14(AR14)的影响。XRD、ICP、FTIR及BET表征结果表明：合成的Zn_xCr-LDHs晶型良好且稳定, 具备介孔结构。实验结果表明：最佳吸附剂为Zn₃Cr-LDHs, 比表面积为101 m²·g^-1, 对AR14的最大吸附容量为484.63 mg·g^-1。同时, 降低溶液pH值和提高溶液温度均可促进AR14的吸附。该吸附过程分别符合准二级动力学模型和Freundlich等温吸附模型。结合Materials Studio 5.5软件模拟, 推测该吸附机理主要以表面吸附为主, -SO₃^-基团是反应点。     

A Rational Repeating Template Method for Synthesis of 2 D Hexagonally Ordered Mesoporous Precious Metals

A repeating template method is presented for the synthesis of mesoporous metals with 2D hexagonal mesostructures. First, a silica replica (i.e., silica nanorods arranged periodically) is prepared by using 2D hexagonally ordered mesoporous carbon as the template. After that, the obtained silica replica is used as the second template for the preparation of mesoporous ruthenium. After the ruthenium species are introduced into the silica replica, the ruthenium species are then reduced by a vapor‐infiltration method by using the reducing agent dimethylamine borane. After the ruthenium deposition, the silica is chemically removed. Analysis by transmission and scanning electron microscopies, a nitrogen‐adsorption–desorption isotherm, and small‐angle X‐ray scattering revealed that the mesoporous ruthenium had a 2D hexagonal mesostructure, although the mesostructural ordering is decreased compared to that of the original mesoporous carbon template. This method is widely applicable to other metal systems. By changing the metal species introduced into the silica replica, several mesoporous metals (palladium and platinum) can be synthesized. Ordered mesoporous ruthenium and palladium, which are not easily attainable by the soft‐templating methods, can be prepared. This study has overcome the composition variation limitations of the soft‐templating method.     

Synthesis and formation of hierarchical mesoporous silica network in acidic aqueous solutions of sodium silicate and cationic surfactant

Synthesis and formation of hierarchical mesoporous silica network in acidic aqueous solutions of commercial sodium silicate and cationic surfactant were studied by SEM, TEM, XRD and nitrogen adsorption-desorption methods. The formation process occurs through several steps, involving (1) formation of mesoporous silica nanoparticles; (2) aggregation of mesoporous silica nanoparticles into blocks; (3) growth of silica nanorods in closely-packed arrays by merging of silica nanoparticles; (4) separation of the nanorods to form 3D silica network; and (4) shrinking of the mesoporous silica network. The as-prepared 3D silica network exhibits bimodal morphology constituting mesoporous and macroporous phases.     

Fabrication and analytical applications of hybrid mesoporous membranes.

Recently, a hybrid mesoporous membrane composed of surfactant-templated mesoporous silica inside a porous anodic alumina membrane has been developed. Since this membrane allows the use of columnar silica-mesopores (silica-nanochannels) as nanofluidic channels, separation of molecules can be realized by mass transport through the silica-nanochannel with molecular dimensions. Here, we review the methods to fabricate the hybrid mesoporous membranes, their structural features, and the analytical applications of hybrid mesoporous membranes.     

有机官能团化介孔分子筛固载铑膦配合物的制备及其对己烯-1氢甲酰化的催化性能

 制备了表面有机官能团化的MCM-41和MCM-48介孔分子筛以及SiO2等载体固载铑膦配合物催化剂,考察了所制备催化剂对液相己烯-1氢甲酰化的催化性能,并用X射线衍射、BET、红外光谱和原子吸收光谱等技术对载体和催化剂的组成和结构进行了表征. 结果表明,固载化铑膦配合物对烯烃氢甲酰化的催化性能与有机官能团的种类及载体的结构有关; 固载于含胺基和腈基有机官能团化介孔分子筛载体的铑膦配合物表现出较高的催化活性和稳定性.     

Ultrastable, redispersible, small, and highly organomodified mesoporous silica nanotherapeutics

Practical biomedical application of mesoporous silica nanoparticles is limited by poor particle dispersity and stability due to serious irreversible aggregation in biological media. To solve this problem, hydrothermally treated mesoporous silica nanoparticles of small size with dual-organosilane (hydrophilic and hydrophobic silane) surface modification have been synthesized. These highly organomodified mesoporous silica nanoparticles were characterized by transmission electron microscopy, X-ray diffraction, N(2) adsorption-desorption, dynamic light scattering, zeta potential, and solid-state (29)Si NMR, and they prove to be very stable in simulated body fluid at physiological temperature. Additionally, they can be dried to a powdered solid and easily redispersed in biological media, maintaining their small size for a period of at least 15 days. Furthermore, this preparation method can be expanded to synthesize redispersible fluorescent and magnetic mesoporous silica nanoparticles. The highly stable and redispersible mesoporous silica NPs show minimal toxicity during in vitro cellular assays. Most importantly, two types of doxorubicin, water-soluble doxorubicin and poorly water-soluble doxorubicin, can be loaded into these highly stable mesoporous silica nanoparticles, and these drug-loaded nanoparticles can also be well-redispersed in aqueous solution. Enhanced cytotoxicity to cervical cancer (HeLa) cells was found upon treatment with water-soluble doxorubicin-loaded nanoparticles compared to free water-soluble doxorubicin. These results suggest that highly stable, redispersible, and small mesoporous silica nanoparticles are promising agents for in vivo biomedical applications.     

以EDTANa2为矿化剂近中性条件下室温合成介孔二氧化硅

利用EDTANa2作为矿化剂, 在近中性条件下于室温合成了厚壁(约3 nm)蠕虫介孔分子筛. 在反应物配比为n(CTAB):n(TEOS):n(EDTANa2):n(H2O)=(0.05~0.2):(0.1~2):(0.1~0.5):(100~500)范围内都能得到介孔二氧化硅. 以XRD、N2吸附、FTIR、SEM和TEM详细考察了体系配比和温度对介孔二氧化硅结构和形貌的影响, 发现CTAB用量越大, 介孔d值相应增大. 温度对介孔二氧化硅的结构和形貌有很大的影响, 温度在2~15 ℃范围内都能生成孔径分布较规则的介孔, 介孔材料的形貌随温度的升高由空心管变成小颗粒聚集体; 合成的介孔分子筛中的模板剂可以通过乙醇萃取的方式除去. 提出了介孔的生成遵从(S+-E-)0-I0中性模板机理.     

Mesoporous Silica Nanoparticles Functionalized with Amino Groups for Biomedical Applications

The synthesis and characterization of amino-functionalized mesoporous silica nanoparticles are presented following two different synthetic methods: co-condensation and post-synthesis grafting of 3-aminopropyltriethoxysilane. The amino groups’ distribution on the mesoporous silica nanoparticles was evaluated considering the aggregation state of a grafted photosensitizer (Verteporfin) by using spectroscopic techniques. The homogeneous distribution of amino groups within the silica network is a key factor to avoid aggregation during further organic functionalization and to optimize the performance of functionalized silica nanoparticles in biomedical applications. In addition, the formation of a protein corona on the external surface of both bare and amino-functionalized mesoporous silica was also investigated by adsorbing Bovine Serum Albumin (BSA) as a model protein. The adsorption of BSA was found to be favorable, reducing the aggregation phenomena for both bare and amino-modified nanoparticles. Nevertheless, the dispersant effect of BSA was much more evident in the case of amino-modified nanoparticles, which reached monodispersion after adsorption of the protein, thus suggesting that amino-modified nanoparticles can benefit from protein corona formation for preventing severe aggregation in biological media.     

有序介孔氧化硅薄膜制备及其组装化学

本文综述了近年来利用有机模板法合成有序介孔二氧化硅薄膜的研究进展，重点阐述了两相界面外延生长和蒸发诱导自组装两种制备方法及其合成机理。此外，讨论了有序介孔二氧化硅薄膜的组装化学，包括金属元素掺杂，纳米粒子在介孔薄膜中的组装，以及有机物/二氧化硅纳米复合薄膜的制备，并对介孔二氧化硅薄膜未来的发展趋势做了展望。     

Reversible replication between ordered mesoporous silica and mesoporous carbon

Highly ordered mesoporous silica can be regenerated from a mesoporous carbon CMK-3 that is a negative replica of mesoporous silica SBA-15, indicating reversible replication between carbon and inorganic materials.     

载有量子点的介孔二氧化硅微球的制备与性能研究

采用自组装方法制备了一种磁核/介孔二氧化硅壳的微球, 调节体系中C₁₈TMS的加入量可控制介孔硅球的比表面积; 并通过化学修饰的方法对介孔微球表面进行巯基功能化修饰. 利用巯基与量子点之间的相互作用可将一定尺寸的量子点吸附于介孔二氧化硅球的孔中, 令介孔微球具有荧光效应; 同时可以利用吸附不同粒径的量子点的荧光光谱对介孔二氧化硅微球孔径的大小进行近似考察.