有机-无机杂化材料膜制备生物传感器用于在线生化需氧量的测定

用溶胶-凝胶与接枝共聚物组成的有机-无机杂化材料固定皮状丝孢酵母制备BOD生物传感器,在研制的在线BOD监测仪上考察其性能。结果表明,该传感器线性高达85．0mg／L BOD,稳定性良好、使用寿命长,可连续使用90d以上,保存14个月后仍可保持70％以上的活性。本方法用于实际样品分析,得到了与传统的5d法较一致的结果,可用于污水的在线监测。     

基于溶胶-凝胶壳聚糖／SiO2杂化材料的安培型葡萄糖生物传感器

近年来，基于溶胶-凝胶技术的有机/无机杂化复合材料由于具有有机物的柔性和易修饰性，以及无机物的刚性和稳定性等，因此有利于保持生物分子的活性和生物传感器的研制．壳聚糖(CS)具有易成膜性和生物相容性，其在生物传感器中的研究已受到重视．本文通过原位溶胶-凝胶(Sol-gel)技术，     

基于溶胶-凝壳聚糖/SiO2杂化材料的安培型葡萄糖生物传感器

近年来 ,基于溶胶 -凝胶技术的有机 /无机杂化复合材料由于具有有机物的柔性和易修饰性 ,以及无机物的刚性和稳定性等 ,因此有利于保持生物分子的活性和生物传感器的研制 [1] .壳聚糖 ( CS)具有易成膜性和生物相容性 ,其在生物传感器中的研究已受到重视 [2 ] .本文通过原位溶胶 -凝胶 ( Sol- gel)技术 ,用 CS和甲基三甲氧基硅烷 ( MTOS)制备了 CS/Si O2 有机 /无机杂化材料 ,并将其用于对葡萄糖氧化酶 ( GOD)的固定 ,研制出葡萄糖生物传感器 .采用人工过氧化物酶普鲁士蓝 ( PB) [3]作为电子传递的媒介体 ,并外加一层 Nafion膜以增强…     

KH-570功能化石墨烯的制备与表征

采用Hummers法对天然石墨进行氧化处理制备了氧化石墨烯,通过γ-甲基丙烯酰氧丙基三甲氧基硅烷与氧化石墨烯反应得到功能化氧化石墨烯,然后在水合肼的作用下制备了功能化石墨烯。未烘干的功能化石墨烯在超声处理下,能稳定分散在体积比为9∶1(V/V)的乙醇/水、丙酮/水或N,N-二甲基甲酰胺/水的混合溶剂中。用傅立叶变换红外光谱、原子力显微镜、X射线光电子能谱及X射线衍射对样品结构、形貌进行了分析。结果表明,KH-570上的硅氧烷与氧化石墨烯上的羟基发生了反应,经水合肼还原后,功能化石墨烯的无序度增加,层间距也比功能化氧化石墨烯的缩小了。功能化石墨烯在DMF/水中呈高度剥离状态,片层厚度为1.1～2.3 nm。     

壳聚糖-纳米金-葡萄糖氧化酶生物传感器的制备及其应用于葡萄糖的测定

采用了一种简便快捷的电沉积方法制备了壳聚糖-纳米金复合膜并应用于葡萄糖生物传感器的构建.氯金酸和壳聚糖的混合液在玻碳电极表面电化学还原为金纳米粒子,再将葡萄糖氧化酶通过戊二醛交联的方式固定在纳米金复合膜修饰的玻碳电极表面,制成一种新型的葡萄糖氧化酶生物传感器.该传感器对葡萄糖的响应十分快速,在5 S内即达到平衡.测定葡萄糖的线性范围为20μmol·L-1～5 mmol·L-1,检出限(3S/N)为12μmol·L-1.     

溶胶-凝胶法合成聚(甲基丙烯酸乙酯-甲基丙烯酸环氧丙酯)/SiO_2杂化聚合物材料

通过溶胶 凝胶过程合成了一系列存在相间偶联键的杂化聚合物材料 .IR分析证实了在无机组份与有机组份间存在碳氮键 ,其特征吸收峰在 1 2 5 0cm-1.DSC的测试结果则表明无机组份含量的增加提高了材料的Tg 值 ,从而提高了杂化材料的使用温度 .利用小角X ray散射 (SAXS)和电镜 (TEM)分析了不同无机组份、不同酸度下体系的形态结构 ,结果表明当无机组份与有机组份的摩尔比为 1∶1且体系的酸度适当时相容性最好 .     

三氟丙基修饰的有机-无机杂化二氧化硅膜制备、氢气分离及水热稳定性能

以三氟丙基三甲氧基硅烷(TFPTMS)和1,2-双(三乙氧基硅基)乙烷(BTESE)为前驱体, 通过溶胶-凝胶法在酸性条件下制备三氟丙基修饰的有机-无机杂化SiO₂膜材料, 并深入研究三氟丙基修饰对溶胶粒径和疏水性能的影响以及膜材料的氢气渗透分离性能和长期水热稳定性. 结果表明三氟丙基已成功修饰到有机-无机杂化SiO₂膜材料中, 且随着TFPTMS修饰量的增加, 溶胶粒径有减小趋势, 膜材料的疏水性能逐渐提高. 当n(TFPTMS)/n(BTESE)＝0.6时, 溶胶平均粒径为2.11 nm, 膜材料对水的接触角达到111.6°±0.7°. H₂在修饰后膜材料中的输运主要遵循微孔扩散机理, 300 ℃时H₂的渗透率为8.86×10^-7 mol·m^-2·s^-1·Pa^-1, H₂/CO₂的理想分离系数达到5.4, 且当进气摩尔比例为1∶1时H₂/CO₂的双组分气体分离系数达到了4.82, 均高于Knudsen扩散分离因子(H₂/CO₂＝4.69), 膜材料呈现出良好的分子筛分性能. 膜材料在250 ℃及水蒸气摩尔含量为5%的水热环境中能稳定工作300 h以上.     

基于纳米复合材料/壳聚糖膜的葡萄糖生物传感器研究

采用纳米普鲁士蓝/金纳米粒子/壳聚糖(nano-PB/AuNPs/Chit)复合膜固定葡萄糖氧化酶(GOD)构建新型葡萄糖生物传感器。通过电化学阻抗谱以及电流-时间曲线法(I-t)研究了传感器的电化学特性。结果表明,传感器在葡萄糖浓度为0.01～1.0 mmol/L范围内呈线性,响应灵敏度为68.15μA.(mmol/L)-1.cm-2,表观米氏常数为5.1 mmol/L。该传感器可用于糖尿病人血糖的测定。     

聚γ-缩水甘油醚氧丙基三甲氧基硅烷的合成与表征

采用双金属氰化络合物催化剂(DMC)催化γ-缩水甘油醚氧丙基三甲氧基硅烷(KH560)开环聚合,合成出结构规整的均聚产物PKH560.通过FTIR2、9Si-NMR1、H-NMR对聚合物的结构进行表征.结果表明,以DMC为催化剂,可以实现KH560的开环聚合,合成出分子量较大的目标产物PKH560.凝胶渗透色谱与多角度激光联用仪(GPC/MALLS)测得该聚合物PKH560的数均分子量大于1×104,分子量分布介于1.10与1.35之间;分析不同聚合时间PKH560的数均分子量与单体转化率之间的关系可知,聚合物的数均分子量Mn与单体转化率呈线性增长关系,聚合物的分子量分布较窄(Mw/Mn=1.10~1.35),表明该聚合反应具有活性聚合的特征.     

SiO_2/Nafion杂化膜固定酶的过氧化氢生物传感器

通过溶胶-凝胶技术制备SiO2/Nafion杂化膜并固定辣根过氧化物酶,以杂化膜中Nafion固定的亚甲基蓝为辣根过氧化物酶和玻碳电极间的电子传递介体,制成了电流型过氧化氢生物传感器。探讨了杂化膜的制备条件、工作电位、pH值、温度、干扰物质等对生物传感器的影响。该生物传感器的线性响应范围为1.0×10-6～1.6×10-4mol/L,检出限(S/N=3)为6.0×10-7mol/L,达到95%稳态响应电流用时少于15s。固定化酶对过氧化氢催化反应的米氏常数为1.129 mmol/L。     

Construction of bienzyme biosensors based on combination of the one-step electrodeposition and covalent-coupled sol-gel process

Horseradish peroxidase (HRP) and glucose oxidase (GOD) bienzyme biosensor was constructed by in-situ formation of the organic-inorganic biocomposite film based on the one-step electrodeposition and covalent-coupled sol-gel process. The electrodeposition was performed in the solution containing functional inorganic precursor possessing the epoxy groups, γ-glycidoxypropyltrimethoxysiloxane (GPTMS), a biopolymer chitosan (CS), HRP and GOD. The covalent-coupled sol-gel process was formed by self-hydrolysis and self-condensation of GPTMS, followed by in-situ covalent cross-linking of CS, HRP and GOD through covalent reaction between amino groups and epoxy groups. The developed bienzyme biosensor presented high stability in acidic solution owing to the covalent-coupled organic-inorganic hybridization. Compared with the non-hybrid HRP-GOD/CS/Au electrode, the bienzyme biosensor of HRP-GOD/GPTMS/CS/Au showed improved sensitivity and a wider linear range for the determination of glucose. The linear response of the developed HRP-GOD/GPTMS/CS/Au biosensor for the determination of glucose ranged from 1 to 351 μmol/L with a detection limit of 0.3 μmol/L.     

AChE biosensor based on zinc oxide sol-gel for the detection of pesticides

Zinc oxide has been used as a matrix for immobilization of acetylcholinesterase (AChE) and detection of the pesticide paraoxon. The immobilized enzyme retained its enzymatic activity up to three months when stored in phosphate buffered saline (pH 7.4) at 4 °C. An amperometric biosensor for the detection of paraoxon was designed. The biosensor detected paraoxon in the range 0.035-1.38 ppm and can be used to detect other AChE inhibiting organophosphate pesticides.     

Amperometric phenol biosensor based on sol-gel silicate/Nafion composite film

An amperometric biosensor based on tyrosinase immobilized in silicate/Nafion composite film has been developed for the determination of phenolic compounds. The Nafion polymer in the composite was used not only to overcome the brittleness of the pure sol-gel-derived silicate film but also to increase the long-term stability of the biosensor. Tyrosinase was immobilized by a thin film of silicate/Nafion composite on a glassy carbon electrode. Phenolic compounds were determined by the direct reduction of biocatalytically-liberated quinone species at −200 mV versus Ag/AgCl (3 M NaCl). The process parameters for the fabrication of the enzyme electrode and various experimental variables such as pH and operating potential were explored for optimum analytical performance of the enzyme electrode. The biosensor can reach 95% of steady-state current in about 15 s. The sensitivities of the biosensor for catechol and phenol were 200 and 46 mA/M, respectively. A detection limit of 0.35 mM catechol was obtained with a signal-to-noise ratio of 3. The enzyme electrode retained 74% of its initial activity after 2 weeks of storage in 50 mM phosphate buffer at pH 7.     

Tyrosinase/laccase bienzyme biosensor for amperometric determination of phenolic compounds

Tyrosinase/laccase bienzyme biosensor for amperometric determination of phenolic compounds was constructed. Enzymes were immobilized in titania gel matrix. The obtained biosensor was successfully used for determination of 2,6-dimethoxyphenol, 4-tertbutylcatechol, 4-methylcatechol, 3-chlorophenol and catechol. The highest sensitivity and the widest linear range were noticed for catechol, 234 mA L mol^− 1 and 2.0 × 10^− 7–3.2 × 10^− 5 mol/L, respectively. Detection limit for catechol, at signal-to-noise ratio of 3 was 1.3 × 10^− 7 mol/L.     

基于胱胺/壳聚糖/酶标纳米金自组装的的酪氨酶传感器的研制

通过自组装技术构制了一种简单有效的酪氨酸酶传感器。该法先通过戊二醛交联将壳聚糖固定在胱胺修饰的金丝电极上,进而通过氨基与纳米金的强力相互作用将酶标纳米金固定在壳聚糖层上。结果表明,酪氨酸酶能很好地保持其生物活性,所构制的传感器达到95%稳定状态电极的时间在15s以内。酚类化合物是通过酶催化产生的醌在-100mV(相对饱和甘汞电极)直接还原而测定的,传感器对邻苯二酚、苯酚、对甲基苯酚测定的灵敏度依次为2.216,4.828,4.885μA·μmol-1L.cm-2,检测限依次为0.32,0.60,0.18μmolL-1。二周后活性仍保持原有活性的75%。     

Measurement of binding kinetics between PI3-K and phosphorylated IGF-1R using a surface plasmon resonance biosensor

A high-performance amperometric glucose biosensor was developed, based on immobilization of glucose oxidase (GOx) on a copper (Cu) nanoparticles/chitosan (CHIT)/carbon nanotube (CNT)-modified glassy carbon (GC) electrode. The Cu and CNT had a synergistic electrocatalytic effect toward the reduction of hydrogen peroxide in the matrix of biopolymer CHIT. The Cu/CHIT/CNT modified GC electrode could amplify the reduction current of hydrogen peroxide greatly. Besides, the Cu/CHIT/CNT modified GC electrode reduces hydrogen peroxide at a much lower applied potential and inhibit the responses of interferents. With GOx as an enzyme model, a new glucose biosensor was fabricated. The sensitivity of the sensor is due not only to the large microscopic area but also to the high efficiency of transformation of H₂O₂ generated by enzymatic reaction to current signal. The biosensor exhibited excellent sensitivity (the detection limit is down to 0.02 mM), fast response time (less than 4 sec), wide linear range (from 0.05 to 12 mM), and perfect selectivity. Correspondence: Wanzhi Wei, State key Laboratory of Chemo/Biosensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, Changsha 410082, China     

A glucose biosensor based on chitosan-Prussian blue-multiwall carbon nanotubes-hollow PtCo nanochains formed by one-step electrodeposition

In this paper, a simple one-step electrodeposition method is described to fabricate chitosan-Prussian blue-multiwall carbon nanotubes-hollow PtCo nanochains (CS-PB-MWNTs-H-PtCo) film onto the gold electrode surface, then glucose oxidase (GOD) and Nafion were modified onto the film subsequently to fabricate a glucose biosensor. The morphologies and electrochemistry of the composite were investigated by using Fourier transform infrared (FTIR) spectrometry, scanning electron microscopy (SEM) and electrochemical techniques including cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), respectively. The performances of the biosensor have been investigated by chronoamperometry method under the optimized conditions. This biosensor showed a linear response to glucose range from 1.5 μM to 1.12 mM with a detection limit of 0.47 μM (S/N=3), a high sensitivity of 23.4 μA mM(-1) cm(-2), and a fast response time. The apparent Michaelis-Menten constant (K(M)(app)) was 1.89 mM. In addition, the biosensor also exhibited strong anti-interference ability, excellent stability and good reproducibility.     

Glucose concentration determination based on silica sol-gel encapsulated glucose oxidase optical biosensor arrays

Optical biosensor arrays for rapidly determining the glucose concentrations in a large number of beverage and blood samples were developed by immobilizing glucose oxidase (GOD) on oxygen sensor layer. Glucose oxidase was first encapsulated in silica based gels through sol-gel approach and then immobilized on 96-well microarrays integrated with oxygen sensing film at the bottom. The oxygen sensing film was made of an organically modified silica film (ORMOSIL) doped with tris(4,7-diphenyl-1,10-phenanthroline) ruthenium dichloride (Ru(dpp)₃Cl₂). The oxidation reaction of glucose by glucose oxidase could be monitored through fluorescence intensity enhancement due to the oxygen consumption in the reaction. The luminescence changing rate evaluated by the dynamic transient method (DTM) was correlated with the glucose concentration with the wide linear range from 0.1 to 5.0 mM (Y = 13.28X − 0.128, R = 0.9968) and low detection limit (0.06 mM). The effects of pH and coexisting ions were systemically studied. The results showed that the optical biosensor arrays worked under a wide range of pH value, and normal interfering species such as Na⁺, K⁺, Cl⁻, PO₄³⁻, and ascorbic acid did not cause apparent interference on the measurement. The activity of glucose oxidase was mostly retained even after 2-month storage, indicating their long-term stability.     

Highly sensitive choline biosensor based on carbon nanotube-modified Pt electrode combined with sol-gel immobilization

A novel amperometric choline biosensor has been fabricated with choline oxidase (ChOx) immobilized by the sol-gel method on the surface of multi-walled carbon nanotubes (MWCNT) modified platinum electrode to improve the sensitivity and the anti-interferential property of the sensor. By analyzing the electrocatalytic activity of the modified electrode by MWCNT, it was found that MWCNT could not only improve the current response to H₂O₂ but also decrease the electrocatalytic potential. The effects of experimental variables such as the buffer solutions, pH and the amount of loading enzyme were investigated for the optimum analytical performance. This sensor shows sensitive determination of choline with a linear range from 5.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol/L when the operating pH and potential are 7.2 and 0.15 V, respectively. The detection limit of choline was 5.0 × 10⁻⁷ mol/L. Selectivity for choline was 9.48 μA·(mmol/L)⁻¹. The biosensor exhibits excellent anti-interferential property and good stability, retaining 85% of its original current value even after a month. It has been applied to the determination of choline in human serum. Translated from Chinese Journal of Analytical Chemistry, 2006, 34(7): 910–914 (in Chinese)     

A sensitive mediator-free tyrosinase biosensor based on an inorganic-organic hybrid titania sol-gel matrix

A novel inorganic-organic hybrid titania sol-gel nanocomposite film was prepared to fabricate a sensitive tyrosinase biosensor for the amperometric detection of trace phenolic compounds without additional electron mediators. Acetylacetone worked as a complexing ligand to chelate with Ti atom in the synthesis process, and the pH of the titania solution could be adjusted to the value which was optimum for retaining tyrosinase activity and such a membrane was stably attached on to the surface of a glassy carbon electrode (GCE). This titania matrix could supply a good environment for enzyme loading, which resulted in a high sensitivity of 15.78 μA μM⁻¹ cm⁻² for monitoring phenols with a detection limit of 1×10⁻⁸ M at a signal-to-noise ratio of 3. The TiO₂ sol-gel derived biosensor exhibited a fast response less than 10 s and a good stability for more than 2 months.