Electrochemical characterization of MWCNT/Ni(OH)<Subscript>2</Subscript> composites as cathode materials

The hydrothermal method was used to synthesize multi-walled carbon nanotube/nickel hydroxide composites (MWCNT/Ni(OH)₂). The structure and morphology of the prepared materials were characterized by X-ray diffraction and transmission electron microscopy. The electrochemical performance of cathodes prepared with multi-walled carbon nanotubes (MWCNT) loaded into the β-nickel hydroxide materials was investigated employing cyclic voltammetry, galvanostatic charge/discharge and electrochemical impedance spectroscopic measurements. It is shown that the cathode active material utilization increases for MWCNT/Ni(OH)₂ obtained after 24 h of hydrothermal synthesis. These composites exhibit a fairly good electrochemical performance as cathode materials. Based on the results, this fact could be associated with the formation of a continuous conductive network structure in the hydroxide matrix. The analyses of impedance data, according to a physicochemical model, allow the improvement of a better understanding of the main structural and physicochemical parameters that control the electrochemical performance of these systems.     

TiO<Subscript>2</Subscript>-SiO<Subscript>2</Subscript> binary xerogels: Synthesis and characterization

Silica/titania binary xerogels were prepared by joint hydrolysis of the ingredients. Gels of various compositions were characterized by ¹H NMR spectroscopy, IR spectroscopy, and thermogravimetry. The spectral characteristics of binary systems differ considerably from mere superposition of the spectra of the two constituent compounds and the spectrum of a mechanical mixture. A feasibility was demonstrated for controlling the acid properties of binary oxide gels via varying the component mole ratio.     

Preparation and characterization of the Ti/IrO<Subscript>2</Subscript>/WO<Subscript>3</Subscript> as supercapacitor electrode materials

WO₃ films have been prepared onto IrO₂-coated Ti substrate by electro-deposition, and as-deposited and annealed films have been characterized by using Raman spectroscopy. It was found that the asdeposited film consists of orthorhombic WO₃ · H₂O phase, which transforms to amorphous WO₃ by annealing at 250°C and to monoclinic phase by annealing at and above 350°C. All electrochemical experiments were carried on Ti/IrO₂/WO₃ annealed at 450°C. The open-circuit potential could change significantly due to the hydration of the coating film. However this process is fairly slow. Reproducible voltammograms could be obtained quickly, further revealing high electrochemical stability of the Ti/IrO₂/WO₃ electrode. And the shapes of CV show the approximate rectangular mirror image, showing the typical characteristic of capacitive behavior. The specific capacitance obtained at a scan rate of 50 mV s⁻¹ is 46 F g⁻¹.     

Controlled growth of ZnO nanorod templates and TiO<Subscript>2</Subscript> nanotube arrays by using porous TiO<Subscript>2</Subscript> film as mask

Silver nanoparticles well dispersed in a spherical Poly(vinylpyrollidone)(PVP) matrix were simply prepared by spray pyrolysis of aqueous solutions of AgNO₃ and PVP without any reducing agent. Highly monodisperse silver particles were obtained above the initial mass ratio of PVP/AgNO₃ ∼ 1 and in a certain narrow temperature range. Below the critical mass ratio the silver particles grew to larger ones polydispersely. As the ratio increased above it, they became smaller maintaining their monodispersity. The use of PVP considerably decreased the reduction temperature of the silver nitrate from 450 °C to 250 °C under the same pyrolysis conditions, due to its reducing nature. As the pyrolysis temperature increased above the decomposition temperature of PVP, the silver particles in the matrix grew to merge to a single particle while their crystallite size did not increase as much. The spherical assemblies of the silver nanoparticles were hardly disengaged even after severe washing off the matrix materials. The mechanism of the nanoparticle growth was also discussed.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Synthesis and supercapacitance of flower-like Co(OH)<Subscript>2</Subscript> hierarchical superstructures self-assembled by mesoporous nanobelts

A facile hydrothermal strategy was first proposed to synthesize flower-like Co(OH)₂ hierarchical microspheres. Further physical characterizations revealed that the flower-like Co(OH)₂ microspherical superstructures were self-assembled by one-dimension nanobelts with rich mesopores. Electrochemical performance of the flower-like Co(OH)₂ hierarchical superstructures were investigated by cyclic voltammgoram, galvanostatic charge–discharge and electrochemical impedance spectroscopy in 3 M KOH aqueous electrolyte. Electrochemical data indicated that the flower-like Co(OH)₂ superstructures delivered a specific capacitance of 434 F g⁻¹ at 10 mA cm⁻² (about 1.33 A g⁻¹), and even kept it as high as 365 F g⁻¹ at about 5.33 A g⁻¹. Furthermore, the SC degradation of about 8% after 1,500 continuous charge–discharge cycles at 5.33 A g⁻¹ demonstrates their good electrochemical stability at large current densities.     

Nanosized TiO<Subscript>2</Subscript> particles decorated on SiO<Subscript>2</Subscript> spheres (TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript>): synthesis and photocatalytic activities

Nanosized TiO₂ and nano-anatase TiO₂ decorated on SiO₂ spherical core shells were synthesized by using a sol–gel method. The synthesized pure TiO₂ nano particle and TiO₂ grafted on SiO₂ sphere with various ratios have been characterized for their structure and morphologies by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectrophotometry (FTIR) and transmission electron microscopy (TEM). Their surface areas were measured using the BET method. The photocatalytic activity of all nanocomposites was investigated using methylene blue as a model pollutant. The synthesized TiO₂/SiO₂ particles appeared to be more efficient in the degradation of methylene blue pollutant, as compared to pure TiO₂ particles.     

Synthesis,characterization and photocatalytic properties of tungsten-doped hydrothermal TiO<Subscript>2</Subscript>

Crystalline anatase phase TiO₂ with photocatalytic properties was obtained through a sol–gel low-temperature hydrothermal process. TiO₂ samples doped with tungsten oxide were also obtained by using this synthetic approach. The photocatalytic oxidation of methylene blue in water was monitored to study the influence of the tungsten doping degree on the photocatalytic degradation performance of TiO₂. The degradation rate constant was further increased by adjusting the tungsten doping degree of hydrothermal TiO₂. Also, a much faster photodegradation of methylene blue was achieved using tungsten doped samples baked at 450°C. The results were compared with those obtained with Degussa P25 used as photocatalyst. The structure and optical properties of tungsten-doped TiO₂ were studied by SEM, X-ray diffraction, UV–vis and DRIFT spectroscopy techniques.     

Synthesis and characterization of radiation sensitive TiO<Subscript>2</Subscript>/monazite photocatalyst

A TiO₂/monazite photocatalyst was prepared by embedding TiO₂ nanoparticles into a monazite substrate surface. TiCl₄ hydrolysis/citric acid chelating procedure under acidic conditions were used to synthesize the nanophase TiO₂ particles. The anatase TiO₂/monazite photocatalyst surface area, morphology, crystalline and elemental concentrations were characterized using Brunauer-Emmett-Teller (BET) method, scanning electron microscopy (SEM), X-ray diffraction (XRD), and inductively coupled plasma-atomic emission spectrometry (ICP-AES). Monazite contains a large amount of Ce-, La-, Nd- and Th-PO₄ compounds; it has been known as a natural mineral material with minor radioactivity. TiO₂-CeO₂ composite is a kind of radiation sensitive photocatalyst in which the radiations of thorium nuclides give energy to trigger TiO₂ and cerium ions which play an energy absorber with charge separator. The result showed that methylene blue and phenol were spontaneously photocatalytic decomposed by TiO₂/monazite composite even in a dark environment. A synergistic effect was also examined with applied exterior UV or ⁶⁰Co irradiation. A hybrid mechanism is proposed; according by the radioluminescence (RL) from excited Ce ion by γ-radiation soliciting CeO₂/TiO₂ heterojunction (HJ). This seems to be a possible mechanism to explain this self-activated photo-catalytic behavior.     

SiO<Subscript>2</Subscript> and TiO<Subscript>2</Subscript> nanoparticles in Aerosol OT reverse microemulsions: Synthesis and characterization

Stable SiO₂ and TiO₂ organosols were prepared by hydrolyzing tetraethyl orthosilicate (TEOS) in the presence of 6–12 M NH₃ and titanium(IV) isopropylate (TTIP) in reverse microemulsions of 0.12–0.25 M bis(2-ethylhexyl) sulfosuccinate (Aerosol OT, AOT) in n-decane with the aqueous pseudophase content of 2–3 vol %, 0.018–0.090 M TEOS, and 0.15–0.55 vol %, 0.003–0.025 M TTIP. The degree of hydrolysis was monitored by IR spectroscopy (for TEOS) and spectrophotometry (for TTIP). Oxide nanoparticles were characterized by photon-correlation spectroscopy (PCS) (D _h = 8–100 nm) and laser electrophoresis (ζ-potential = 7.4–11.6 mV). The occurrence of surface potential made it possible to separate the oxides from the excess of surfactant by nonaqueous electrophoresis and to determine particle sizes (7–40 nm) by means of transmission electron microscopy (TEM).     

Synthesis and characterization of TiO<Subscript>2</Subscript>-montmorillonite nanocomposites and their photocatalytic activity

TiO₂ nanoparticles have been synthesized on the surface of exfoliated montmorillonite at a low temperature in benzyl alcohol medium. According to X-ray diffraction (XRD), N₂ adsorption-desorption isotherm and transmisson electron microscopy (TEM), it was found that the intercalation of TiO₂ nanoparticles destroyed the ordered structure of montmorillonite to some extent, and the crystallites of the nanocomposites are assembled to form a house-of-cards structure. The size of the nanoparticles in the interlamellar space is about 4 nm. The nanocomposites exhibited excellent photocatalytic activity in methylene blue degradation due to the synergetic effect of the adsorptive ability to organic compound of cetyl trimethylammonium bromide—montmorillonite and the catalytic ability of TiO₂ nanoparticles in it.     

Synthesis details and solubility product for cobalt hydroxo salt Co(OH)<Subscript>1.8</Subscript>Cl<Subscript>0.2</Subscript>

The hydroxo salt Co(OH)_1.8Cl_0.2 is precipitated by a deficit of OH^? ions from dilute CoCl₂ solutions under the conditions that inhibit the appearance of local excesses of OH^? ions. The three-variable method is used to determine the solubility product for this compound. A linear correlation between the composition and solubility product is found for Co(OH)₂, Co(OH)_1.8Cl_0.2, and Co(OH)_1.5Cl_0.5.     

Synthesis and characterization of macroporous Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C composites as cathode materials for Li-ion batteries

The macroporous Li₃V₂(PO₄)₃/C composite was synthesized by oxalic acid-assisted carbon thermal reaction, and the common Li₃V₂(PO₄)₃/C composite was also prepared for comparison. These samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and electrochemical performance tests. Based on XRD and SEM results, the sample has monoclinic structure and macroporous morphology when oxalic acid is introduced. Electrochemical tests show that the macroporous Li₃V₂(PO₄)₃/C sample has a high initial discharge capacity (130 mAh g⁻¹ at 0.1 C) and a reversible discharge capacity of 124.9 mAh g⁻¹ over 20 cycles. Moreover, the discharge capacity of the sample is still 91.5 mAh g⁻¹, even at a high rate of 2 C, which is better than that of the sample with common morphology. The improvement in electrochemical performance should be attributed to its improved lithium ion diffusion coefficient for the macroporous morphology, which was verfied by cyclic voltammetry and electrochemical impedance spectroscopy.     

TiO<Subscript>2</Subscript> nanofibers embedding single crystalline TiO<Subscript>2</Subscript> nanowires

Epitaxially grown titanium dioxide (TiO₂) nanofibers embedding single crystalline TiO₂ nanowires (NWs) were successfully fabricated by electropinning poly(vinyl pyrrolidone)/ethanol solutions mixed with hydrothermally synthesized TiO₂ NWs and titanium isopropoxide precursors and subsequently calcinating the electrospun nanofibers. Utilizing scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the morphologies of TiO₂ NWs and nanofibers were investigated. High resolution TEM (HR-TEM) and selected area electron diffraction (SAED) allowed us to indentify the fact that, during the calcination process under the optimized condition, titanium isopropoxide precursors were epitaxially crystallized on the surface of single crystalline TiO₂ NWs. Based on the X-ray diffraction (XRD) experiments, it was also realized that the crystalline structure of hydrothermally synthesized TiO₂ NWs and epitaxially crystallized TiO₂ nanofibers is anatase and that TiO₂ composite nanofibers embedding TiO₂ NWs exhibited a higher crystallinity than the pristine TiO₂ nanofibers. Additionally, ultraviolet visible (UV–Vis) spectra of nanofibers indicated that optical properties of TiO₂ nanofibers can be tuned by introducing the single crystalline TiO₂ NWs.     

Synthesis and characterization of a new hybrid TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> filler for lithium conducting gel electrolytes

This paper describes the synthesis and properties of a new type of ceramic fillers for composite polymer gel electrolytes. Hybrid TiO₂-SiO₂ ceramic powders have been obtained by co-precipitation from titanium(IV) sulfate solution using sodium silicate as the precipitating agent. The resulting submicron-size powders have been applied as fillers for composite polymer gel electrolytes for Li-ion batteries based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF/HFP) copolymeric membranes. The powders, dry membranes and gel electrolytes have been examined structurally and electrochemically, showing favorable properties in terms of electrolyte uptake and electrochemical characteristics in Li-ion cells.     

Synthesis and thermal decomposition of neodymium(III) peroxotitanate to Nd<Subscript>2</Subscript>TiO<Subscript>5</Subscript>

Neodymium(III) peroxotitanate is used as a precursor for obtaining Nd₂TiO₅. The last one possesses numerous valuable electrophysical properties. TiCl₄, Nd(NO₃)₃·6H₂O and H₂O₂ in mol ratio 1:2:10 were used as starting materials. The reaction ambience was alkalized to pH = 9 with a solution of NH₃. The obtained neodymium(III) peroxotitanate and intermediate compounds of the isothermal heating were proved by the help of quantitative analysis and infrared spectroscopy (IRS). It has Nd₄[Ti₂(O₂)₄(OH)₁₂]·7H₂O composition. The absorption band observed in IRS at 831 cm^?1 relates to a triangular bonding of the peroxo group of Ti, at 1062 cm^?1—terminal groups Ti–OH and at 1491 and 1384 cm^?1—the bridging OH^?-groups Ti–O(H)–Ti. Nd₂TiO₅ was obtained by thermal decomposition of neodymium(III) peroxotitanate. The isothermal conditions for decomposition were determined on the base of differential thermal analysis, thermogravimetric and differential scanning calorimetry results in the temperature range of 20–1000 °C. The mechanism of thermal decomposition of Nd₄[Ti₂(O₂)₄(OH)₁₂]·7H₂O to Nd₂TiO₅ was studied. In the temperature range of 20–208 °C, a simultaneous decomposition of the peroxo groups by the separation of oxygen and hydrate water is conducted and Nd₄[Ti₂O₄(OH)₁₂] is obtained. From 208 to 390 °C, the terminal OH^?-groups are separated and Nd₄[Ti₂O₇(OH)₆] is formed. In the range of 390–824 °C, the bridging OH^?-groups are completely decomposed to Nd₂TiO₅. The optimal conditions for obtaining nanocrystalline Nd₂TiO₅ are 900 °C for 6 h and 20–80 nm.     

Hydrothermally synthesized Ni(OH)<Subscript>2</Subscript>@Zn(OH)<Subscript>2</Subscript> composite with enhanced electrochemical performance for supercapacitors

Two kinds of electrode materials Ni(OH)₂ and Ni(OH)₂@Zn(OH)₂ composite are fabricated on nickel foam. Electrochemical experiments indicate Ni(OH)₂@Zn(OH)₂ composite deserves further study due to high specific capacitance and good cycle stability, so that it can achieve energy storage and conversion as much as possible. When the hydrothermal time is different, the electrochemical performance of the sample is also different. Accurately, samples can obtain better electrochemical performance at 15 h, and the maximum specific capacitance of Ni(OH)₂@Zn(OH)₂ is 7.87 F cm^?2 compared to Ni(OH)₂ (0.61 F cm^?2) at 5 mA cm^?2. Even at 50 mA cm^?2, specific capacitance is 5.24 F cm^?2 and rate capability is 66.6%. Furthermore, Ni(OH)₂@Zn(OH)₂-15 h loses 19.8% after 1000 cycles, revealing the composite has an outstanding stable cycle. These properties also indicate Ni(OH)₂@Zn(OH)₂-15 h is a promising electrode material.     

Synthesis,characterization of B-doped TiO<Subscript>2</Subscript> nanotubes with high photocatalytic activity

B-doped TiO₂ nanotubes (B/TiO₂ NTs) were prepared by the combination of sol–gel process with hydrothermal treatment. The prepared catalysts were characterized by XRD, TEM and XPS. The photocatalytic activity of B/TiO₂ NTs was evaluated through the photodegradation of aqueous methyl orange. The results demonstrated that the 1.5% B/TiO₂ NTs calcined at 300 °C possessed the best photocatalytic activity. Compared with pure TiO₂ nanotubes, the doping with B significantly enhanced the photocatalytic efficiency.     

Co<Subscript>2</Subscript>(OH)<Subscript>3</Subscript>Cl xerogels with 3D interconnected mesoporous structures as a novel high-performance supercapacitor material

Co₂(OH)₃Cl xerogel interconnected mesoporous structures have been prepared by a facile one pot sol-gel process and heat treated at 200 and 400 °C. All samples are studied for their morphology, structure, and electrochemical stability upon cycling. The specific capacitance of the as-prepared Co₂(OH)₃Cl from single electrode study is 450 F/g, when the electrodes are cycled in 3 M KOH at a specific current 2 A/g. Interestingly, capacity retention after 500 and 1000 cycles is about 92 and 75 %, respectively. Sample heated at 200 °C exhibits 308 F/g at 2 A/g and that heated at 400 °C shows only 32 F/g at 0.2 A/g. With an increase in preparation temperature, amorphous Co₂(OH)₃Cl is converted to crystalline Co₃O₄ phases with lower electrochemical performance. In full cell study, as-prepared Co₂(OH)₃Cl showed a capacity of about 49 F/g as asymmetric capacitor and 32 F/g as symmetric capacitor at 2 A/g current density. Co₂(OH)₃Cl being a novel porous material with merits of homogeneous porosity, high surface area, and an interconnected three dimensional (3D) structure exhibits considerably high capacitance. With a significant specific capacity and electrochemical stability, the synthesized material is a novel potential candidate for supercapacitors.

Open image in new window

Graphical abstract ?