超声化学技术合成MnO2/MoS2纳米交互积层材料

层状氧化锰在氢氧化四甲基胺溶液中超声处理20分钟后，层状氧化锰剥离成纳米层胶体分散液。层状LiMoS₂在超声条件下浸入到10^-4M HNO₃溶液中，随后将得到的处理液加入到层状氧化锰纳米层胶体分散液中，超声处理合成得到了MnO₂/MoS₂纳米交互积层材料，提出了相同电性无机纳米层间超声化学合成新型交互积层材料新技术。     

杂化钙钛矿(NH3C6H12NH3)CuCl4的制备与表征

采用低温溶液法合成了含有二铵阳离子结构的新型二维层状结构的有机/无机杂化钙钛矿材料（NH₃C₆H₁₂NH₃） CuCl₄。采用元素分析、红外光谱、X射线衍射和紫外-可见光吸收光谱等手段对其结构与性能进行了表征。结果表明该材料的紫外-可见吸收光谱吸收峰位于285 nm和387 nm,层间距为1.18 nm。二铵阳离子的引入,使有机层⁺NH₃C₆H₁₂NH₃+与2个相邻的无机框架CuCl₄^2-分别通过较强的氢键结合在一起,排列更为规整,热稳定性更高。与单铵阳离子结构的杂化钙钛矿材料相比,由于不存在两层有机分子层间较弱的范德华力,（NH₃C₆H₁₂NH₃） CuCl₄材料的电阻率为1.36×10⁵ Ω·cm,比单胺结构的杂化钙钛矿材料的电阻率低3个数量级。     

层状钨基氧化物复合材料的合成与电子特性

W₂O₆·H₂O /一元烷基胺复合物[(C_nH_2n+1NH₂，n=4、8、12、16)嵌入层状氧化钨W₂O₆·H₂O] 的XRD、IR、TG-DSC分析表明：烷基胺C_nH_2n+1NH₂能基于质子加合的机制嵌入W₂O₆·H₂O层间，且插层复合物之间烷基胺的插入与抽出是个可逆过程；烷基胺嵌入层间后以全反式构象双层排布，层间距d随烷基胺碳原子数的增加而线性增长，烷基链与层板的夹角为71.6°。插层复合物UV-Vis分析发现，各种复合物的禁带宽度相对半导体氧化钨的禁带宽度变宽了很多，这表明可以通过嵌入不同的物质来调节氧化钨层与层之间的电子传递能力。     

柱撑阴离子粘土的合成、表征及催化性能研I.ZnAl─SiW11及ZnAl—SiW11Z的合成

采用水热合成及离子交换方法将缺位及单取代型Keggin结构钨硅杂多含氧酸根SiW₁₁及SiW₁₁O₃₉Z(H₂O)^6-嵌入Zn─Al型阴离子粘土层间,得到了大层间距的新型层往状微孔材料ZnAl─SiW₁₁及ZnAl-SiW₁₁Z(Z=Co²⁺、Ni²⁺和Cu²⁺),XRD与IR测试结果表明,它们只有9.7Å 的通道高度.     

大比表面积钛黑颜料的制备和表征

本文首次通过pH值控制沉淀法制备前驱物丁二酸钛肼复盐, 并进一步热分解制备大比表面积钛黑颜料-黑色钛氧化物。通过比表面积(BET)、电子能谱(EDS)、X射线光电子能谱分析(XPS)、X射线粉末衍射(XRD)、场发射扫描电子显微镜(HRSEM)、物理吸附仪、激光粒度仪和Color i5型台式分光测色仪对黑色钛氧化物进行了表征, 确定了黑色钛氧化物的组成为2TiO₂·Ti₂O₃, 其表面积为53.854 4 m²·g^-1。并考察了酸源、水合肼用量、酸钛比、反应时间、pH、NaOH浓度和煅烧温度等各种反应参数对黑色钛氧化物的颗粒尺寸、分布均匀性和黑色度的影响。用元素分析仪和等离子体光谱仪测定了前驱物组成, 确定其组成为[Ti(C₄H₄O₄)₂]_0.85·2Ti₂O₃·6N₂H₄·3H₂O, 并探讨了黑色钛氧化物形成机理, 为新型混合价材料黑色钛氧化物的制备提供重要参考依据。     

锂离子电池正极材料LiNi0.75-xCoxMn0.25O2的合成及电化学性能研究

以LiOH·H₂O、Ni(OAc)₂·4H₂O、Co(OAc)₂·4H₂O和MnO₂为原料，在水热反应釜中预处理，然后进行高温固相反应，合成了一系列锂镍钴锰氧化物LiNi_0.75-xCo_xMn_0.25O₂(x=0.05,0.10,0.15,0.20,0.25)。通过X射线衍射(XRD)、扫描电子显微镜（SEM）和电化学性能测试对所得样品的结构、形貌、粒径及电化学性能进行了表征。结果表明，当x=0.20时，所合成的正极材料具有很好的α-NaFeO₂型层状晶体结构，晶胞参数a=0.286 1 nm，c=1.416 4 nm， V=0.100 4 nm³，以50 mA·g^-1的电流密度在3～4.3 V(vs Li/Li⁺)充放电时，首次放电比容量达172.5 mAh·g^-1，首次放电效率高达90.9%，30个循环后其放电比容量依然保持在161.1 mAh·g^-1。     

钙钛矿氧化物H1.9K0.3La0.5Bi0.1Ta2O7和Pt/WO3组成的Z体系下完全光解水性能

以质子化层状钙钛矿氧化物H_1.9K_0.3La_0.5Bi_0.1Ta₂O₇ (HKLBT)作为产氢催化剂, Pt/WO₃作为产氧催化材料进行Z 型体系下完全分解水反应. 考察了不同载流子传递介质及不同载流子浓度对反应活性的影响. 结果表明, 以Fe²⁺/Fe³⁺为载流子传递介质时可以实现水的完全分解(H₂/O₂体积比为2:1), 8 mmol·L^-1的FeCl₃作为初始载流子传递介质时, 产氢、产氧活性分别为66.8和31.8 μmol·h^-1, 氢氧体积比为2.1:1. 受光催化材料对载流子传递介质氧化还原速度的限制, 过高的载流子传递介质浓度并不能提高光催化活性.     

长链烷胺及手性钛的螯合物Ti[(OC2H4)3N][OCH(CH3)2]在层状V2O5中的插层行为

用一种简便快速方法合成了一系列长链有机胺插层V₂O₅化合物. 用粉末X射线衍射(XRD)、红外光谱(FT-IR)、漫反射紫外-可见光谱(DR UV-VIS)等手段对插层产品的结构进行了表征. 除了正十六胺插层V₂O₅产品外, 其它长链烷胺插层V₂O₅产品的层间距d₀₀₁与长链烷胺碳数n之间具有良好的线性关系: d₀₀₁＝0.160n_C＋0.731 nm. 正十六胺与V₂O₅反应后生成两个插层相, 一个相的层间距d₀₀₁为4.01 nm, 另一相的d₀₀₁为3.20 nm. 此外, 研究了手性钛的螯合物Ti[(OC₂H₄)₃N][OCH(CH₃)₂] (记为TEAIP)在V₂O₅层间的插层行为, 得到相应的插层产品.     

银-磷酸钛纳米复合膜的构建及其电化学生物传感

利用ITO基底上层层组装构建的多层内嵌银纳米粒子的磷酸钛薄膜固定了血红蛋白并且用于生物传感研究。由于银纳米粒子与磷酸钛膜的协同作用,实验中可以观察到Hb的直接电子传递。研究表明所制备的Hb-Ag-TiP/PDDA/ITO电极对H₂O₂响应迅速、稳定,检测限达3.3×10^-6 mol·L^-1。     

水滑石焙烧产物-镁铝复合氧化物表面性质的反相气相色谱研究

用共沉淀法制备的镁铝水滑石(Mg/Al物质的量比为3),经一定温度焙烧后,得到“笼”状结构的复合氧化物,并采用反相气相色谱法(IGC)对复合氧化物和混合氧化物(氧化镁和氧化铝)的表面性质进行了研究。实验测得一系列探针分子在复合氧化物和混合氧化物上的保留时间,可计算出其吸附热力学函数(吸附自由能(ΔG^?),吸附焓(ΔH^?),吸附熵(ΔS^?)),表面能色散组分(γ_S^d)及复合氧化物的表面酸碱参数(K_A,K_D),并探讨了探针分子在复合氧化物上的吸附机理。结果表明,探针分子进入复合氧化物的“笼”状结构后,可以减小温度对探针分子吸附过程的影响。此外,计算出复合氧化物的表面酸碱参数K_A=3.21及K_D=21.02,定量地表明镁铝复合氧化物是一种两性偏碱的材料。     

Pillared titanates: Titanium oxide of high surface area and porosity

Pillaring layered titanates with robust polyoxometallic oligomers is a route to prepare microporous titanium oxide. In addition to using the organic intercalated compounds as precursors, the pillaring reaction on this layered metal oxide with a high charge density was facilitated by using layered titanate of low crystallinity and small particle size, which was achieved by hydrolyzing TiCl₄ in strong alkaline solution. The resultant compound had a formula close to that of layered trititanate, NaHTi₃O₇·2H₂O. Both aluminium Keggin ions, formulated as [Al₁₃O₄(OH)₂₄(H₂O)₁₂]⁷⁺, and hydroxyzirconium tetramer cations, formulated as [Zr₄(OH)₈(H₂O)₁₆]⁸⁺, were introduced into the interlayers of this layered titanate. The layered structure was retained up to 600°C for the alumina-pillared derivative, but only to 500°C for the zirconia-pillared derivative. The pillared samples had BET surface areas ⩾ 150 m²/g and contained both micro- and mesopores. Many of the physicochemical properties of the compounds before and after pillaring were compared. Most of the characteristic properties of TiO₂ were retained on the pillared derivatives.     

Graphene Nanosheets as a Platform for the 2D Ordering of Metal Oxide Nanoparticles: Mesoporous 2D Aggregate of Anatase TiO2 Nanoparticles with Improved Electrode Performance

Graphene nanosheets are successfully applied as an effective platform for the 2D ordering of metal oxide nanoparticles. Mesoporous 2D aggregates of anatase TiO₂ nanoparticles are synthesized by the heat treatment of the uniformly hybridized nanocomposite of layered titanate–reduced graphene oxide (RGO) at elevated temperatures. The precursor layered titanate–RGO nanocomposite is prepared by self‐assembly of anionic RGO nanosheets and cationic TiO₂ nanosols. The calcination of the as‐prepared layered titanate–RGO nanocomposite at 500 °C induces a structural and morphological change of layered titanate nanoplates into anatase TiO₂ nanoparticles without significant modification of the RGO nanosheet. Increasing the heating temperature to 600 °C gives rise to elimination of the RGO component, leading to the formation of sheetlike porous aggregates of RGO‐free TiO₂ nanoparticles. The nanocomposites calcined at 500–700 °C display promising functionality as negative electrodes for lithium ion batteries. Among the present calcined derivatives, the 2D sheet‐shaped aggregate of TiO₂ nanoparticles obtained from calcination at 600 °C delivers the greatest specific discharge capacity with good capacity retention for all current density conditions applied. Such superior electrode performance of the nanocomposite calcined at 600 °C is attributable both to the improved stability of the crystal structure and crystal morphology of titania and to the enhancement of Li⁺ ion transport through the enlargement of mesopores. The present findings clearly demonstrate the usefulness of RGO nanosheets as a platform for 2D‐ordered superstructures of metal oxide nanoparticles with improved electrode performance.     

Highly Dispersed TiO6 Units in a Layered Double Hydroxide for Water Splitting

A family of photocatalysts for water splitting into hydrogen was prepared by distributing TiO₆ units in an MTi‐layered double hydroxide matrix (M=Ni, Zn, Mg) that displays largely enhanced photocatalytic activity with an H₂‐production rate of 31.4 μmol h^?1 as well as excellent recyclable performance. High‐angle annular dark‐field scanning transmission electron microscopy (HAADF‐STEM) mapping and XPS measurement reveal that a high dispersion of TiO₆ octahedra in the layered doubled hydroxide (LDH) matrix was obtained by the formation of an M²⁺‐O‐Ti network, rather different from the aggregation state of TiO₆ in the inorganic layered material K₂Ti₄O₉. Both transient absorption and photoluminescence spectra demonstrate that the electron–hole recombination process was significantly depressed in the Ti‐containing LDH materials relative to bulk Ti oxide, which is attributed to the abundant surface defects that serve as trapping sites for photogenerated electrons verified by positron annihilation and extended X‐ray absorption fine structure (EXAFS) techniques. In addition, a theoretical study on the basis of DFT calculations demonstrates that the electronic structure of the TiO₆ units was modified by the adjacent MO₆ octahedron by means of covalent interactions, with a much decreased bandgap of 2.1 eV, which accounts for its superior water‐splitting behavior. Therefore, the dispersion strategy for TiO₆ units within a 2D inorganic matrix can be extended to fabricate other oxide or hydroxide catalysts with greatly enhanced performance in photocatalysis and energy conversion.     

精氨酸插层氧化锰纳米结构材料的制备和表征

应用氧化法水热合成了Na型层状氧化锰[BirMO(Na)], 通过离子交换反应在0.1 mol/L HCl溶液中Na型层状氧化锰转化成H型层状氧化锰[BirMO(H)]. BirMO(H)在四甲基氢氧化铵[(CH3)4NOH]溶液中搅拌处理7 d后, 剥离生成了MnO2纳米层胶体分散液. 剥离的MnO2纳米层胶体分散液在pH＝4.0～11.0的精氨酸溶液中搅拌2 d, 得到了层间距为1.49 nm的精氨酸插层氧化锰纳米结构材料. 通过XRD, DSC-TGA, SEM, IR及元素分析对合成试样进行了分析表征. 结果表明精氨酸在氧化锰层间的插入量及插入形式与重组溶液的pH值密切相关, 其最大插入量为1.80 mmol/g.     

Preparation and characterization of SiO2/TiO2 composite microspheres with microporous SiO2 core/mesoporous TiO2 shell

SiO₂/TiO₂ composite microspheres with microporous SiO₂ core/mesoporous TiO₂ shell structures were prepared by hydrolysis of titanium tetrabutylorthotitanate (TTBT) in the presence of microporous silica microspheres using hydroxypropyl cellulose (HPC) as a surface esterification agent and porous template, and then dried and calcined at different temperatures. The as-prepared products were characterized with differential thermal analysis and thermogravimetric (DTA/TG), scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption. The results showed that composite particles were about 1.8 μm in diameter, and had a spherical morphology and a narrow size distribution. Uniform mesoporous titania coatings on the surfaces of microporous silica microspheres could be obtained by adjusting the HPC concentration to an optimal concentration of about 3.2 mmol L⁻¹. The anatase and rutile phase in the SiO₂/TiO₂ composite microspheres began to form at 700 and 900 °C, respectively. At 700 °C, the specific surface area and pore volume of the SiO₂/TiO₂ composite microspheres were 552 and 0.652 mL g⁻¹, respectively. However, at 900 °C, the specific surface area and pore volume significantly decreased due to the phase transformation from anatase to rutile.     

ESR and reflectance spectra of manganese in polycrystalline TiO2 (rutile)

The ESR and reflectance spectra of polycrystalline TiO₂ containing manganese oxide (up to 8% atomic ratio) have been investigated. The results show that there is only a limited solubility of substitutional Mn⁴⁺ in TiO₂. The manganese ions are isolated, since the solubility limit prevents clustering of Mn⁴⁺ in TiO₂ matrix. Manganese in excess (with respect to the solubility value) is present as MnTiO₃. The electronic spectrum of Mn⁴⁺ in the rutile lattice is discussed on the basis of the behavior of isoelectronic Cr³⁺ in solid solution in TiO₂.     

Preparation of TiO2 Sol Using TiCl4 as a Precursor

A titanium dioxide sol with narrow particle size distribution was synthesized using TiCl₄ as the starting material. The sol was prepared by a process where HCl was added to a gel of hydrated titanium oxide to dissolve it. The resulting aqueous titanic acid solution was heated to form titanium dioxide sol. The effects of preparation parameters were investigated. TiCl₄ was slowly added to distilled water at 5°C. Aqueous solution of sodium hydroxide was added to adjust the pH of the system to 8–12. After aging for a period of time, the peptized sol was filtered and sufficiently washed. The filtered cake was repulped in water. Hydrochloric acid was slowly added to the solution with stirring. After condensation reaction and crystallization, a transparent sol with suspended TiO₂ was formed. XRD results show that the crystalline phase was anatase. The suspended TiO₂ particles were rhombus primary particles with the major axis ca. 20 nm and the minor axis ca. 5 nm. The TiO₂ particles prepared at pH 8 had the largest surface area of 141 cm³/g and it was microporous. The compositions of the solution which yielded the smallest suspended TiO₂ particles were TiO₂:HCl (35% HCl) = 1:1 (molar ratio), concentration of TiO₂ = 10%. Hydroxypropyl cellulose with viscosity of 150–400 cps was added as a dispersant. The sol was excellent in dispersibility and long-term stability. Transparent thin films could be obtained through dip-coating glass substrate in the sol. The dip-coating on glass can be less than three times to have one monolayer TiO₂. The transparent TiO₂ thin film had strong hydrophilicity after being illuminated by UV light.     

Fabrication of Predominantly Mn4+‐Doped TiO2 Nanoparticles under Equilibrium Conditions and Their Application as Visible‐Light Photocatalyts

The chemical state of a transition‐metal dopant in TiO₂ can intrinsically determine the performance of the doped material in applications such as photocatalysis and photovoltaics. In this study, manganese‐doped TiO₂ is fabricated by a near‐equilibrium process, in which the TiO₂ precursor powder precipitates from a hydrothermally obtained transparent mother solution. The doping level and subsequent thermal treatment influence the morphology and crystallization of the TiO₂ samples. FTIR spectroscopy and X‐ray photoelectron spectroscopy analyses indicate that the manganese dopant is substitutionally incorporated by replacing Ti⁴⁺ cations. The absorption band edge can be gradually shifted to 1.8 eV by increasing the nominal manganese content to 10 at %. Manganese atoms doped into the titanium lattice are associated with the dominant 4+ valence oxidation state, which introduces two curved, intermediate bands within the band gap and results in a significant enhancement in photoabsorption and the quantity of photogenerated hydroxyl radicals. Additionally, the high photocatalytic performance of manganese‐doped TiO₂ is also attributed to the low oxygen content, owing to the equilibrium fabrication conditions. This work provides an important strategy to control the chemical and defect states of dopants by using an equilibrium fabrication process.     

Electrochemical Property of Manganese Oxide Nanobelt Bundles with Layered Structure

One‐dimensional manganese oxide nanobelt bundles with birnessite‐type structure have been synthesized by a hydrothermal process in a NaOH solution employing K‐type layered manganese oxide as a precursor. The obtained manganese oxide nanobelt bundles exhibit excellent discharge properties and cycle stability. The initial capacity is 376 mAh·g^?1 and the reversible capacity of 243 mAh·g^?1 is maintained after the 50th cycle at a current density of 20 mA·g^?1. Meanwhile, the manganese oxide nanobelt bundles show an excellent cycle performance even if at relative high current density.