Kinetic spectrophotometric determination of traces of sulfide

A method for the determination of sulfide based on the addition reaction of sulfide with magenta at pH 7 and 25 degrees C is described. The decrease in absorbance of magenta at 540 nm, its lambda(max), over a fixed time is proportional to the concentration of sulfide over the range of 25-2500 ng ml(-1). The limit of detection was found to be 15 ng ml(-1). Ten replicate analysis of a sample solution containing 1.5 mug ml(-1) sulfide gave a relative standard deviation of 0.8%. The effects of various cations and anions on sulfide determination have been reported and procedures for removal of interferences have been described.     

Organic solvent-soluble membrane filters for the preconcentration and spectrophotometric determination of iron(II) traces in water with Ferrozine

An organic solvent-soluble membrane filter (MF) is proposed for the simple and rapid reconcentration with subsequent spectrophotometric determination of trace levels of iron (II) in water. Iron (II) is collected on a nitrocellulose membrane filter as ion associate of an anionic complex, which is formed by iron (II) and Ferrozine and a cation-surfactant. The ion-pair compound and the MF can be dissolved in small volumes of 2-ethoxyethanol and the absorbance of the resulting solution is measured at 560 nm against a reagent blank with molar absorptivity of 4.01 × 10⁴ L mol^–1 cm^–1. Beer’s law is obeyed over the concentration range 0–10 μg L^–1 of iron (II) in water and the detection limit is 0.03 μg L^–1 with a 50-fold enrichment factor. The proposed method can satisfactorily be applied to the determination of iron (II) in natural water and sea water. Received: 23 June 1998 / Revised: 21 July 1998 / Accepted: 25 August 1998     

Kinetic spectrophotometric determination of traces of sulfide in nonionic micellar medium

A sensitive kinetic spectrophotometric method for the determination of ng amounts of sulfide has been developed based on the reduction of Azure A by sulfide in the presence of Brij-35 at pH 7. The decrease in absorbance of Azure A at 600 nm is proportional to the concentration of sulfide over the range 25–1400 ng mL^–1. The variables affecting the rate of the reaction were investigated and the optimum conditions were established. The method is simple, rapid, precise, sensitive, and widely applicable. The limit of detection is 17 ng mL^–1, and the relative standard deviation of seven determinations of 500 ng mL^–1 sulfide was 2.1%. The method was applied to the determination of sulfide in spring water.     

Kinetic spectrophotometric determination of traces of sulfide in nonionic micellar medium

A sensitive kinetic spectrophotometric method for the determination of ng amounts of sulfide has been developed based on the reduction of Azure A by sulfide in the presence of Brij-35 at pH 7. The decrease in absorbance of Azure A at 600 nm is proportional to the concentration of sulfide over the range 25-1,400 ng mL(-1). The variables affecting the rate of the reaction were investigated and the optimum conditions were established. The method is simple, rapid, precise, sensitive, and widely applicable. The limit of detection is 17 ng mL(-1), and the relative standard deviation of seven determinations of 500 ng mL(-1) sulfide was 2.1%. The method was applied to the determination of sulfide in spring water.     

Organic solvent-soluble membrane filters for the preconcentration and spectrophotometric determination of iron(II) traces in water with Ferrozine

An organic solvent-soluble membrane filter (MF) is proposed for the simple and rapid reconcentration with subsequent spectrophotometric determination of trace levels of iron (II) in water. Iron (II) is collected on a nitrocellulose membrane filter as ion associate of an anionic complex, which is formed by iron (II) and Ferrozine and a cation-surfactant. The ion-pair compound and the MF can be dissolved in small volumes of 2-ethoxyethanol and the absorbance of the resulting solution is measured at 560 nm against a reagent blank with molar absorptivity of 4.01 × 10⁴ L mol^–1 cm^–1. Beer’s law is obeyed over the concentration range 0–10 μg L^–1 of iron (II) in water and the detection limit is 0.03 μg L^–1 with a 50-fold enrichment factor. The proposed method can satisfactorily be applied to the determination of iron (II) in natural water and sea water.     

Synergetic extraction and spectrophotometric determination of iron (II) in steel

Summary A simple and rapid method is described for synergetic extraction and spectrophotometric determination of iron(II). The Fe(II)--furildioxime-pyridine complex extracted into chloroform has a characteristic pink color measurable at 570 nm. Iron is also separated from associated elements and the results of the analysis of synthetic mixtures and standard steel samples are reported.

---

Zusammenfassung Eine einfache und rasche Methode zur Extraktion und Bestimmung von Eisen(II) wurde beschrieben. Der Komplex Fe(II)--Furildioxim-Pyridin wird mit Chloroform extrahiert. Seine charakteristische rosa Farbe ist bei 570 nm meßbar. Eisen läßt sich so auch von Begleitelementen trennen. Die Analysenergebnisse für synthetische Gemische und Standard-Stahlproben werden mitgeteilt.

     

Diformylhydrazine as analytical reagent for spectrophotometric determination of iron(II) and iron(III)

The bidentate ligand diformylhydrazine (OHC-HN-NH-CHO), DFH, combines with iron(II) and iron(III) in alkaline media in the pH range 7.3-9.3 to form an intensely colored red-purple iron(III) complex with an absorption maximum at 470 nm. Beer's law is obeyed for iron concentrations from 0.25 to 13 microg mL(-1). The molar absorptivity was in the range 0.3258x10(4)-0.3351x10(4) L mol(-1) cm(-1) and Sandell's sensitivity was found to be 0.0168 microg cm(-2). The method has been applied to the determination of iron in industrial waste, ground water, and pharmaceutical samples.     

Kinetic spectrophotometric determination of tetraphenylporphinecobalt(II) based on photochromism of immobilized norbornadiene

The cobalt(II) complex is detected spectrophotometrically by its catalysis of a photochromic isomerism of norbornadiene (NBD). NBD is immobilized on porous glass beads, and is isomerized to quadricyclane (QC) by UV irradiation. The beads are then immersed in a solution containing tetraphenylporphinecobalt(II) [TPPCo(II)], and the QC is converted back to NBD by a catalytic reaction with TPPCo(II). The rate constant, measured spectrophotometrically, is proportional to the concentration of TPPCo(II). The detection limit of TPPCo(II) is 60 μM for a reaction period of 1 h. This spectrophotometric detection can be applied repetitively without any supply of the chemical reagent, as NBD immobilized on the porous glass beads can be re-isomerized to QC by UV irradiation.     

Sequential flow-injection spectrophotometric determination of iron(II) and iron(III) by copper(II)-catalyzed reaction with Tiron

A flow injection method for the sequential determination of iron(II) and iron(III) was developed. It is based on the differential reaction kinetics of iron(II) and iron(III) with Tiron in a double-injection FI system. The proposed method employs the accelerating action of copper(II) for the oxidation of iron(II) in the presence of Tiron. A linear calibration graph is obtained for iron (II) and iron(III) in the concentration range 1.8 × 10^–5– 1.8 × 10^–4 mol/L; the throughput of samples is 30 injections/h. Received: 22 October 1996 / Revised: 4 December 1996 / Accepted: 10 December 1996     

Sequential flow-injection spectrophotometric determination of iron(II) and iron(III) by copper(II)-catalyzed reaction with Tiron

A flow injection method for the sequential determination of iron(II) and iron(III) was developed. It is based on the differential reaction kinetics of iron(II) and iron(III) with Tiron in a double-injection FI system. The proposed method employs the accelerating action of copper(II) for the oxidation of iron(II) in the presence of Tiron. A linear calibration graph is obtained for iron (II) and iron(III) in the concentration range 1.8 × 10^–5– 1.8 × 10^–4 mol/L; the throughput of samples is 30 injections/h.     

Kinetic spectrophotometric determination of antimony(III) based on induced oxidation of tris(1,10-phenanthroline)iron(II) by chromium(VI)

The method involves the measurement of the extent of the induced reaction, which ceases a few seconds after initiation. Antimony(III) can be determined in the range 0.4–10 μg ml^-1. The standard deviation is ±0.25 μg. The method is applied to marine sediments.     

Kinetic spectrophotometric method for gold(III) determination

The kinetic spectrophotometric method for Au(III) determination was developed and validated. It was based on the catalytic effect of gold on the oxidation of methylene blue B (3,7di-(dimethyl amino)-10-dehydro-phenotiazin chloride) by ammonium peroxo-disulfate in citric buffer solution. There was the linearity of the calibration curve in the concentration range from 0.09 to 2.90 μg ml⁻¹ Au(III). The relative standard deviation was 2.50% and correlation coefficient of 0.9999. The limit of detection was determined as signal to noise ratio (3:1) and it was 5.5 ng ml⁻¹. The limit of quantification, based on signal to noise ratio 10:1 was 19.25 ng ml⁻¹. The selectivity was tested on the basis of influence of known amounts of different ions in the reaction mixture, upon the reaction rate. Kinetic and thermodynamic parameters were reported for both catalytic and non-catalytic reactions. The method was verified by Au(III) determination in anti-rheumatic drug “Tauredon” and in human urine samples, using ICP-AES as the comparative method. As the method is accurate, reliable, quick and simple it could be useful for clinical and toxicological practice.     

Ion flotation—spectrophotometric determination of traces of chromium(VI)

Ion flotation is used to concentrate chromium(VI) in the range 3–70μg l^-1 from 14 samples. The chromium(III)—diphenylcarbazone complex formed by reaction with diphenylcarbazide is floated efficiently with sodium lauryl sulfate, and the subsided foam is measured spectrophotometrically after simple dilution. Continuous flotation methods at solution flow rates of 2, 3 and 4 l h^-1 are discussed.     

Kinetic spectrophotometric determination of iron oxidation states in geological materials

Summary A kinetic spectrophotometric approach is applied to the determination of iron oxidation states in geological materials. Silicate rock samples were sealed in a Teflon vial under argon atmosphere and were decomposed with a mixture of hydrofluoric acid and sulphuric acid by the microwave digestion technique. The absorbance of iron(III)-Tiron complex was followed at 560 nm and the absorbance/time relation was analyzed by non-linear least squares fitting. The FeO and Fe₂O₃ determinations in silicate rocks by the proposed kinetic method agree with those done by the static o-phenanthroline method. The analytical results for standard igneous rock samples are compared with published data.     

Micro-fusion and spectrophotometric determination of iron(II) and iron(III) in chrome spinels and other refractories

Spectrophotometric determination of FeO in milligram samples of chrome spinels and related refractory minerals after high-frequency micro-fusion with lithium tetraborate in an inert atmosphere is described. Anomalous responses (apparent reduction or oxidation of FeO depending on the ferroïn-type reagent)_rendered the procedure highly unreliable. All the fluxes containing structural oxygen, as well as phosphoric acid, acted as oxidants even when atmospheric oxidation was rigorously excluded. However, the method is suitable for micro-determination of total iron in spinels. Spectrophotometric measurements gave an average relative standard deviation of 0.73%.     

Spectrophotometric and derivative spectrophotometric determination of iron by extraction of the iron(II)-TPYZ-picrate ion-association complex

A solvent extraction-spectrophotometric determination of microamounts of iron has been developed, based on the formation of an ion-association complex of iron(II) with 2,4,6-tris(2'-pyridyl)-1,3,5-triazine as primary ligand and picrate as counter-ion, which is extracted into 1,2-dichloroethane. The complex is formed at pH 4.0-7.0 and the iron concentration can be determined by measuring the absorbance directly in the organic phase. The apparent molar absorptivity is 2.2 x 10(5) l.mole(-1).cm(-1). As the method is practically free from interferences it was applied to the determination of iron in different biological and inorganic samples. Although the proposed method is very sensitive it can be further sensitized by employing the derivative spectrophotometric technique.     

Sequential determination of iron(II) and iron(III) in pharmaceutical by flow-injection analysis with spectrophotometric detection.

A flow injection procedure for the sequential spectrophotometric determination of iron(II) and iron(III) in pharmaceutical products is described. The method is based on the catalytic effect of iron(II) on the oxidation of iodide by bromate at pH = 4.0. The reaction was monitored spectrophotometrically by measuring the absorbance of produced triiodide ion at 352 nm. The activating effect for the catalysis of iron(II) was extremely exhibited in the presence of oxalate ions, while oxalate acted as a masking agent for iron(III). The iron(III) in a sample solution could be determined by passing through a Cd-Hg reductor column introduced in the FIA system to reduce iron(III) to iron(II), which allows total iron determination. Under the optimum conditions, iron(II) and iron(III) could be determined over the range of 0.05 - 5.0 and 0.10 - 5.0 microg ml(-1), respectively with a sampling rate of 17 +/- 5 h(-1). The experimental limits of detection were 0.03 and 0.04 microg ml(-1) for iron(II) and iron(III), respectively. The proposed method was successfully applied to the speciation of iron in pharmaceutical products.     

Kinetic spectrophotometric determination of trace manganese (II) with dahlia violet in nonionic microemulsion medium

A new catalytic kinetic spectrophotometric method has been developed for the determination of trace amount of manganese (II) in nonionic microemulsion medium. The method is based on the catalytic effect of manganese (II) on the oxidation of dahlia violet by potassium periodate with nitrilotriacetic acid as an activitor in the presence of nonionic microemulsion. Under the optimum conditions, the calibration graph is linear in the range of 0.0004-0.0056 μg ml⁻¹ of manganese (II) at 580 nm. The detection limit achieved is 3.75×10⁻⁵ μg ml⁻¹. Manganese (II) in foodstuff samples was determined with satisfactory results.