块状壳聚糖多孔支架内交替浸渍沉积磷灰石层

在聚合物支架内沉积羟基磷灰石涂层有望提高支架的生物活性和骨传导性. 本研究采用交替浸渍沉积法, 以块状壳聚糖(Cs)三维多孔支架为沉积模板, 在氯化钙溶液和磷酸氢二钠溶液中交替浸渍, 沉积了羟基磷灰石(HA)涂层. 应用XRD、FT-IR、SEM、孔隙率测试、焙烧法和压缩实验对沉积前后支架的组成、形貌、孔隙率、无机物沉积量以及压缩强度进行了表征. 研究结果表明, 支架上沉积物为低结晶度的碳酸羟基磷灰石, 沿c轴择优生长, 与天然骨中磷灰石类似. 扫描电镜照片显示, 磷灰石在支架孔壁上的沉积量呈梯度分布, 外部沉积量多于内部, 靠近支架表面孔隙部分堵塞, 但内部仍保持连通的孔隙结构. 经6次交替浸渍处理的支架, 孔隙率为94.0%, 羟基磷灰石沉积量达到总质量的13.5%, 压缩强度则由0.055 MPa提高到0.109 MPa.     

Evaluation of the porous structures of new polymer packing materials by inverse size-exclusion chromatography

A highly cross-linked porous polymer resin based on styrene-divinylbenzene matrix with pores created by the use of micellar imprinting technique was used as chromatographic packing material. Its performance as a column packing material in inverse size-exclusion chromatography was compared with a non-imprinted resin of the same polymer matrix. The porous structures (the pore size and the porosity) of the resins in the dry and wet states and their relationships with the elution volume of probe solutes (alkanes and polystyrene standards) were established. Characteristic properties of the resins such as specific pore volume, specific surface area and porosity are compared with results obtained by other methods of characterization such as mercury intrusion porosimetry, solvent regain and nitrogen sorption. The results show that the new porous resin can be used in the separation of small molecules. The separation is based on the size of the molecules, and the larger pores (meso- and macropores) in the porous resin can provide a much easier access to the smaller pores (micropores) which are useful in the chromatographic separations.     

2H-solid state NMR and DSC study of isobutyric acid in mesoporous silica materials

Solid state deuterium NMR has been used to study the molecular motion of d(6)-isobutyric acid (d(6)-iBA) in the pure (unconfined) state and confined in the cylindrical pores of two periodic mesoporous silica materials (MCM-41, pore size 3.3 nm and SBA-15, pore size 8 nm), and in a controlled pore glass (CPG-10-75, pore size ca. 10 nm). The line shape analysis of the spectra at different temperatures revealed three rotational states of the iBA molecules: liquid (fast anisotropic reorientation of the molecule), solid I (rotation of the methyl group) and solid II (no rotational motion on the time scale of the experiment). Transition temperatures between these states were determined from the temperature dependence of the fraction of molecules in these states. Whereas the solid I-solid II transition temperature is not affected by confinement, a significant lowering of the liquid-solid I transition temperature in the pores relative to the bulk acid was found for the three matrix materials, exhibiting an unusual dependence on pore size and pore morphology. Complementary DSC measurements on the same systems show that the rotational melting (solid I-liquid) of d(6)-iBA in the pores occurs at a temperature 20-45 K below the thermodynamic melting point. This finding indicated that the decoupling of rotational and translational degrees of freedom in phase transitions in confined systems previously found for benzene is not restricted to molecules with non-specific interactions, but represents a more general phenomenon.     

基体石墨的孔隙结构及其对单质Ag扩散的影响

高温气冷堆燃料元件的基体石墨是一种多孔复合材料,是燃料元件的主要组成部分,其结构影响燃料元件的性能和裂变产物在燃料元件中的扩散。 本文利用压汞法表征基体石墨的孔隙结构,并讨论了基体石墨制备工艺中最大压制压强与热处理过程对孔隙结构的影响。 结果表明,基体石墨大孔孔径分布为6001900 nm,高温热处理使基体石墨的总孔隙率、中值孔径、大孔孔容均减小;基体石墨热处理样品的大孔孔容随最大压制压强的增加而呈线性减少,热处理过程单质Ag在石墨基体中的扩散速度与大孔孔容变化具有正相关性。     

Surface melting of octamethylcyclotetrasiloxane confined in controlled pore glasses: curvature effects observed by 1H NMR

We have measured the thickness of the pre-molten surface layer that appears at the interface of octamethylcyclotetrasiloxane (OMCTS) to the matrix in controlled pore glasses with pore diameters ranging 7.5-73 nm. Except for the glass with the largest pores, the layer thickness data for different pore diameters fall on a single master curve when plotted versus Tm - T, where Tm is the size-dependent volume melting point of the pore-confined OMCTS. Hence, at a single temperature, the surface layer thickness depends strongly on the curvature of the pore wall and therefore that of the solid-liquid interface. For temperatures where it exceeds two monolayers, the layer thickness depends logarithmically on Tm - T; for the glass with the largest pores, this turns into a power law with the exponent -1/2. The results are interpreted in terms of a continuous model of the solid-liquid interface with an arbitrary curvature. Because OMCTS is a weakly polar molecule with close to spherical shape, our data also lend themselves to Lennard-Jones type simulations.     

Morphological changes of ethylene/vinyl acetate-based controlled delivery systems during release of water-soluble solutes

Thin slabs of theophylline and monomer albumin release systems were prepared by dispersing 212-300 μm and 300-25 μm particles respectively, of these bioactive agents in a methylene chloride solution of ethylene/vinyl acetate (EVAc) copolymer (40 wt% vinyl acetate), and evaporating the solvent at low temperatures according to the Langer—Folkman technique. Compositions containing 21.41 wt%, 31.04 wt% and 40.0 wt% albumin, and 19.32 wt% theophylline were prepared. Solute release experiments were performed in deionized water at 37 ± 0.1°C under perfect-sink conditions. The concentration of released solute was determined by measuring the absorbance of the UV spectra at 276 nm for albumin and 272 nm for theophylline. Both solutes could be released for long periods of time at controlled rates. The main mechanism of release was established to be solute dissolution and diffusion through the generated, waterfilled pore structure. Photomicrographs present the main features of this pore network. Mercury porosimetry was used to determine the pore volume and size of pores for freezedried slabs before, during and after the dissolution/diffusion/release process. Considerable pore collapse was observed and pore diameters of 8-650 μm were detected. In addition to solution diffusion through large pores, diffusion might occur through small constrictions between large pores or through a pore network of much smaller pores created in the matrix.     

Porous structure of natural and modified clinoptilolites

The evaluation of the pore-size distribution (PSD) of natural and modified mesoporous zeolites, i.e., clinoptilolites is presented. We demonstrate the SEM results showing that the pores of fracture-type from 25-50 nm to 100 nm in size between clinoptilolite grains, as well as pores between crystal aggregates up to 500 nm in size are present in the studied material. The detailed distribution of pore sizes and tortuosity factor of the above-mentioned materials are determined from the adsorption-desorption isotherms of nitrogen measured volumetrically at 77 K. To obtain the reliable pore size distribution (PSD) of the above-mentioned materials both adsorption and desorption branches of the experimental hysteresis loop are described simultaneously by recently developed corrugated pore structure model (CPSM) of Androutsopoulos and Salmas. Evaluated pore size distributions are characterized by well-defined smooth peaks placed in the region of the mesoporosity. Moreover, the mean pore diameter calculated from the classical static measurement of nitrogen adsorption at 77 K correspond very well to the pore diameters from SEM, showing the applicability of the CPSM for characterization of the porosity of natural zeolites. We conclude that classical static adsorption measurements combined with the proper modeling of the capillary condensation/evaporation phenomena are a powerful method which can be applied for pore structure characterization of natural and modified clinoptilolites.     

Penetration into three-dimensional complex porous structures

The short-term uptake of a fluid by porous media is important in a number of processes, such as in coating and printing operations. We present a new model to predict short-term absorption into real pore geometries taking into account fluid properties, surface forces, and the complex pore geometry. Two assumptions are made to reduce the complexity of the situation: (1) the flow resistance between pores can be estimated from pore geometry or air permeability measurements, and (2) the volume of fluid in the constrictions between pores is small. Pores can be connected in any manner and can be in any arrangement. The absorption rates predicted by the model are compared to experimental values obtained with coating layers of plastic, kaolin, and calcium carbonate pigments. These coatings are characterized in terms of void fraction, pore size, contact angle, and permeability. The comparison is good for water and inks when the air permeability of the porous layer is used to determine the average resistance to flow in the sample. These resistance values are close to the values obtained from pore geometries estimated from particle packing simulations.     

Low density ionogels obtained by rapid gellification of tetraethyl orthosilane assisted by ionic liquids

A non-hydrolytic one pot sol-gel method has been used to synthesize mesoporous silica ionogels with the confined ionic liquid (IL) 1-ethyl 3-methyl imidazolium tetra fluoro-borate [EMIM][BF(4)]. The precursor for obtaining the SiO(2) matrix was tetraethyl orthosilicate (TEOS) and formic acid was used as a catalyst. These ionogels have been characterized by density measurements, TEM, BET, DSC, TGA and FTIR. The incorporation of the ionic liquid [EMIM][BF(4)] enhances the gellification rate which results in the ionogels having very low density (~0.3 g cm(-3)). The low density has been explained on the basis of the creation of 'blind embedded pores' in the matrix (apart from open pores) due to very rapid gellification (~1 min). Morphological studies provide experimental evidence for the presence of blind pores/voids inside the ionogel ingots. We have also shown that the IL entrapped in nanopores (~7-8 nm pore size) of the SiO(2) matrix has different physical properties than the bulk IL viz. (a) the phase transition temperatures (T(g), T(c) and T(m)) of the IL change upon confinement, (b) the thermal stability reduces upon confinement, and (c) the pore wall interaction with the IL results in changes in the C-H vibrations of the imidazolium ring and alkyl chain (the former increasing) which is also indicated in our DFT-calculation.     

新型固液双重致孔球形离子交换剂的制备及其性能研究

以甲基丙烯酸缩水甘油酯为单体 ,采用固液联合致孔方式 ,通过一步悬浮聚合制备了一种新型双孔高分子球形载体 .经化学修饰后 ,得到含二乙胺羟丙基的阴离子交换剂 (介质A) .优化了制备条件 .并与用相同方法制备的但仅含有机溶剂致孔剂的介质B进行了比较 .介质A和B均具有较高的静态吸附容量和机械强度 .由于介质A内含有流动相可以对流通过的大孔 ,因此其动态吸附容量远高于介质B ,并且在较高的流速下表现出较好的色谱流动性能     

The effects of polymer chain rigidification, zeolite pore size and pore blockage on polyethersulfone (PES)-zeolite A mixed matrix membranes

The polyethersulfone (PES)-zeolite 3A, 4A and 5A mixed matrix membranes (MMMs) were fabricated with a modified solution-casting procedure at high temperatures close to the glass transition temperatures (T_g) of polymer materials. The effects of membrane preparation methodology, zeolite loading and pore size of zeolite on the gas separation performance of these mixed matrix membranes were studied. SEM results show the interface between polymer and zeolite in MMMs experiencing natural cooling is better (i.e., less defective) than that in MMMs experiencing immediate quenching. The increment of glass transition temperature (T_g) of MMMs with zeolite loading confirms the polymer chain rigidification induced by zeolite. The experimental results indicate that a higher zeolite loading results in a decrease in gas permeability and an increase in gas pair selectivity. The unmodified Maxwell model fails to correctly predict the permeability decrease induced by polymer chain rigidification near the zeolite surface and the partial pore blockage of zeolites by the polymer chains. A new modified Maxwell model is therefore proposed. It takes the combined effects of chain rigidification and partial pore blockage of zeolites into calculation. The new model shows much consistent permeability and selectivity predication with experimental data. Surprisingly, an increase in zeolite pore size from 3 to 5 Å generally not only increase gas permeability, but also gas pair selectivity. The O₂/N₂ selectivity of PES-zeolite 3A and PES-zeolite 4A membranes is very similar, while the O₂/N₂ selectivity of PES-zeolite 5A membranes is much higher. This implies the blockage may narrow a part of zeolite 5A pores to approximately 4 Å, which can discriminate the gas pair of O₂ and N₂, and narrow a part of zeolites 3A and 4A pores to smaller sizes. It is concluded that the partial pore blockage of zeolites by the polymer chains has equivalent or more influence on the separation properties of mixed matrix membranes compared with that of the polymer chain rigidification.     

In-pore tensile stress by drying-induced capillary bridges inside porous materials

We present here some evidences that capillary liquid bridges are able to deform micrometric cylindrical pores by tensile stress. Brine-soaked filter membranes are submitted to drying conditions leading to NaCl precipitation inside the 5-10 μm pores. A close examination demonstrated that two forms of NaCl crystallites are successively generated. First, primary cubic crystals grow, driven by the permanent evaporation. When this angular primary solid gets near the pore wall, while the evaporation makes the pore volume to be partly invaded by air, capillary liquid can bridge the now-small gap between the halite angles and the pore wall. In a second step, these small capillary bridges are frozen by a secondary precipitation event of concave-shaped NaCl. The proposed interpretation is that the liquid capillary bridges deform the host matrix of the membrane, and the situation is fossilized by the growth of solid capillary bridges. A quantitative interpretation is proposed and the consequences towards the natural media outlined.     

Interfacial effects on vitrification of confined glass-forming liquids

Mesoporous silica phases, with uniform pores of dimensions in the 2-30 nm range, offer a uniquely well-defined environment for the study of the effects of two-dimensional spatial confinement on the properties of glass-forming liquids. We report observations by differential scanning calorimetry of the vitrification of o-terphenyl (OTP), salol, and glycerol in hexagonal mesoporous silica (MCM-41 and SBA-15) in a wide range of pore sizes from 2.6 to 26.4 nm. In agreement with previous studies, where a controlled porous glass is used as a solid matrix, the glass transition temperature for o-terphenyl diminishes with decreasing pore size. In contrast to OTP, glycerol shows a gradual increase in glass transition temperature, while in salol a slight reduction of glass transition temperature is observed, followed by an increase, which results in glass transition temperature indistinguishable from that of the bulk for the smallest pores. These results are discussed in terms of liquid-surface interactions in an interfacial layer, monitored by Fourier-transformed infrared spectroscopy in the study. The hydrogen bonding with silica surface silanols dominates the glass transition trends observed in salol and glycerol.     

Nanochannel array plastics with tailored surface chemistry

The utilization of nanoporous substrates in applications such as selective ion transport, biomolecule separation, seeded templating, and catalysis necessitates the ability to efficiently control pore surface properties. We approached this task by preparing nanoporous polymer monoliths from ABC triblock copolymer precursors that assemble into a cylindrical morphology, where the A block constitutes matrix, C is the removable minor component, and B provides the functionality on the surface of the pores. Polystyrene-polydimethylacrylamide-polylactide (PS-PDMA-PLA) triblock copolymers were prepared by a combination of controlled ring-opening and free-radical polymerization techniques. After selective etching of the PLA cylinders from shear-aligned monoliths, a nanoporous polystyrene matrix containing a hexagonally packed array of hydrophilic, PDMA-coated channels was obtained. Extremely high degrees of alignment and order could be attained, and nanoporous substrates with second-order orientation factors of as high as 0.96 were prepared. PDMA brushes inside the pores were then hydrolyzed in a controlled fashion to introduce a desired number of carboxylic acid groups to the internal pore surface. Carbodiimide mediated couplings with amines were then used to confirm the accessibility of the interior acidic groups and to render materials with different functional content. This modular approach allows for the convenient preparation of functionalized nanoporous materials from a single block copolymer precursor.     

Importance of molecular shape in the adsorption of nitrogen,carbon dioxide and methane on surfaces and in confined spaces

The importance of shape in the adsorption of nitrogen, carbon dioxide and methane (common molecular probes for solid characterization) on surfaces and in confined spaces is investigated for its effects on the adsorption capacity and isosteric heat. We study the possibility of using an equivalent pseudo-sphere model to describe the potential energy of interaction of these molecular probes. On a flat open surface, we find that the equivalent pseudo-sphere model describes adsorption of these species sufficiently well. However, in the confined space of pores, especially pores that accommodate three layers or less, the pseudo-sphere model describes the adsorption badly because of the geometrical constraint on the molecular packing. It is recommended that to study adsorption properly in small pores, potential models that correctly describe molecular shape should be used. In characterization, pseudo-sphere models are commonly used to generate the kernels (local isotherms) for the determination of pore size distribution which can lead to misleading results. We illustrate this with an example to show that the wrong pore size distribution results if pseudo-sphere kernels are used.     

煤颗粒燃烧的孔隙特性研究

以实验为基础,系统研究了典型煤种燃烧时的颗粒孔隙过程。采用低温吸附法和电子显微图像计算机法测量了煤燃烧过程中的颗粒孔隙,获得了颗粒孔径分布和孔形分布等孔隙特性,建立了煤颗粒燃烧的微孔效应和亚微孔效应理论。     

Characterization of pH-induced changes in the morphology of polyelectrolyte multilayers assembled from poly(allylamine) and low molecular weight poly(acrylic acid)

We report characterization of pH-dependent behavior in polyelectrolyte multilayers (PEMs) fabricated from poly(allylamine) (PAH) and low molecular weight poly(acrylic acid) (PAA) synthesized by living/controlled polymerization. Exposure of these films to solutions of low pH (e.g. pH 2.0-3.2) resulted in transformations from films that were smooth and uniform to films with porous morphologies, as characterized by scanning electron microscopy (SEM). We observed large differences in both the extent of this transformation and the sizes of the pores that resulted compared to films fabricated using higher molecular weight PAA used in past studies. Whereas transformations reported in past studies generally lead to pores with sizes in the range of 0.3-2 μm, we observed larger-scale transformations and films with cell-like internal structures comprised of networks of closed pores, interconnected pores, and through-pores with sizes as large as 10-15 μm depending on pH and the manner in which the films were incubated. Films fabricated using fluorescently end-labeled samples of PAA permitted real-time imaging of changes in internal structure using confocal microscopy (LSCM). The results of these studies also revealed large differences in the nature of these transformations when films were placed in contact with surfaces as opposed to when dipped into aqueous solutions. Our results reveal approaches that can be used to fabricate films with large pores (e.g., pores with sizes on the order of 10-15 μm) and suggest methods that could potentially be used to generate PEMs having controlled gradients in pore size.     

Nucleation free energy of pore formation in an amphiphilic bilayer studied by molecular dynamics simulations

The formation of a pore in a membrane requires a considerable rearrangement of the amphiphilic molecules about to form the bilayer edge surrounding the pore, and hence is accompanied by a steep increase of the free energy. Recent rupture and conductance experiments suggest that this reshuffling process is also responsible for a small energy barrier that stabilizes "prepores" with diameters of less than 1 nm, rendering both the opening and closing of pores an activated process. We use the potential of mean constraint force method to study this free energy profile, as a function of pore radius, in a coarse grained bilayer model. The calculations show that the free energy rises by (15-20) kT during pore opening, making it an extremely rare nucleation event. Although we do not observe a barrier to pore closure, the results do make the existence of such a barrier plausible. For larger pores we find a smooth transition to Litster's model, from which a line tension coefficient of about 3.7 x 10(-11) J m(-1) is deduced.     

Hierarchically porous carbon membranes derived from PAN and their selective adsorption of organic dyes

Porous carbon membranes were favorably fabricated through the pyrolysis of polyacrylonitrile(PAN) precursors, which were prepared with a template-free technique-thermally induced phase separation. These carbon membranes possess hierarchical pores, including cellular macropores across the whole membranes and much small pores in the matrix as well as on the pore walls. Nitrogen adsorption indicates micropores(1.47 and 1.84 nm) and mesopores(2.21 nm) exist inside the carbon membranes, resulting in their specific surface area as large as 1062 m2/g. The carbon membranes were used to adsorb organic dyes(methyl orange, Congo red, and rhodamine B) from aqueous solutions based on their advantages of hierarchical pore structures and large specific surface area. It is particularly noteworthy that the membranes present a selective adsorption towards methyl orange, whose molecular size(1.2 nm) is smaller than those of Congo red(2.3 nm) and rhodamine B(1.8 nm). This attractive result can be attributed to the steric structure matching between the molecular size and the pore size, rather than electrostatic attraction. Furthermore, the used carbon membranes can be easily regenerated by hydrochloric acid, and their recovery adsorption ratio maintains above 90% even in the third cycle. This work may provide a new route for carbon-based adsorbents with hierarchical pores via a template-free approach, which could be promisingly applied to selectively remove dye contaminants in aqueous effluents.