Characterization of polymer-silica nanocomposite particles with core-shell morphologies using Monte Carlo simulations and small angle X-ray scattering

A two-population model based on standard small-angle X-ray scattering (SAXS) equations is verified for the analysis of core-shell structures comprising spherical colloidal particles with particulate shells. First, Monte Carlo simulations of core-shell structures are performed to demonstrate the applicability of the model. Three possible shell packings are considered: ordered silica shells due to either charge-dependent repulsive or size-dependent Lennard-Jones interactions or randomly arranged silica particles. In most cases, the two-population model produces an excellent fit to calculated SAXS patterns for the simulated core-shell structures, together with a good correlation between the fitting parameters and structural parameters used for the simulation. The limits of application are discussed, and then, this two-population model is applied to the analysis of well-defined core-shell vinyl polymer/silica nanocomposite particles, where the shell comprises a monolayer of spherical silica nanoparticles. Comprehensive SAXS analysis of a series of poly(styrene-co-n-butyl acrylate)/silica colloidal nanocomposite particles (prepared by the in situ emulsion copolymerization of styrene and n-butyl acrylate in the presence of a glycerol-functionalized silica sol) allows the overall core-shell particle diameter, the copolymer latex core diameter and polydispersity, the mean silica shell thickness, the mean silica diameter and polydispersity, the volume fractions of the two components, the silica packing density, and the silica shell structure to be obtained. These experimental SAXS results are consistent with electron microscopy, dynamic light scattering, thermogravimetry, helium pycnometry, and BET surface area studies. The high electron density contrast between the (co)polymer and the silica components, together with the relatively low polydispersity of these core-shell nanocomposite particles, makes SAXS ideally suited for the characterization of this system. Moreover, these results can be generalized for other types of core-shell colloidal particles.     

Biphasic synthesis of Au@SiO2 core-shell particles with stepwise ligand exchange

We report the synthesis of well-dispersed core-shell Au@SiO(2) nanoparticles with minimal extraneous silica particle growth. Agglomeration was suppressed through consecutive exchange of the stabilizing ligands on the gold cores from citrate to L-arginine and finally (3-mercaptopropyl)triethoxysilane. The result was a vitreophilic, stable gold suspension that could be coated with silica in a biphasic mixture through controlled hydrolysis of tetraethoxysilane under L-arginine catalysis. Unwanted condensation of silica particles without gold cores was limited by slowing the transfer across the liquid-liquid interface and reducing the concentration of the L-arginine catalyst. In-situ dynamic light scattering and optical transmission spectroscopy revealed the growth and dispersion states during synthesis. The resulting core-shell particles were characterized via dynamic light scattering, optical spectroscopy, and electron microscopy. Their cores were typically 19 nm in diameter, with a narrow size distribution, and could be coated with a silica shell in multiple steps to yield core-shell particles with diameters up to 40 nm. The approach was sufficiently controllable to allow us to target a shell thickness by choosing appropriate precursor concentrations.     

单分散聚丙烯酸丁酯-二氧化硅核壳粒子的制备

近年来,有机-无机核壳材料因其具有可调的光、电、磁等特性而备受关注．无机物外壳可以增强粒子的热力学稳定性、机械强度和抗拉性能．高分子乳胶粒内核具有弹性,且易成膜,外部包覆无机物的乳胶粒可结合两者特性并产生协同效应．     

Polystyrene-silica nanocomposite particles via alcoholic dispersion polymerization using a cationic azo initiator

Submicrometer-sized polystyrene-silica nanocomposite particles have been prepared by alcoholic dispersion polymerization of styrene using commercial alcoholic silica sols of 13 or 22 nm diameter as the sole stabilizing agent. The key to the formation of colloidally stable nanocomposite particles is the selection of a cationic azo initiator (use of nonionic or anionic initiators leads either to the formation of silica-stabilized polystyrene latex particles with very low silica contents or to the precipitation of polystyrene, respectively). Neither surface modification of the silica sol nor the addition of surfactant or polymeric stabilizers is required for successful nanocomposite syntheses. The purified polystyrene-silica nanocomposite particles have relatively narrow particle size distributions, with mean diameters ranging from 331 to 464 nm as judged by disk centrifuge photosedimentometry. Thermogravimetric analyses indicated mean silica contents of 13-26 wt. %, depending on the synthesis conditions. Calcination of the polystyrene-silica nanocomposite particles leads to the formation of hollow silica shells, which indicates a well-defined core-shell morphology for the original nanocomposite particles.     

苯乙烯在阴离子型聚氨酯纳米水分散液中聚合过程的研究

采用自乳化法制备出阴离子聚氨酯纳米水分散液,以其作为乳化剂使苯乙烯单体在其中进行聚合,制备出不同聚苯乙烯与聚氨酯质量比的阴离子型PS/PU纳米复合物水分散液;对苯乙烯单体的聚合过程进行了研究;采用光子相关谱仪和透射电镜对其微观结构、粒径及其分布进行了测试,结果表明,该方法能够制备出稳定的具有核壳结构的PS/PU纳米复合物水分散液,但当苯乙烯单体浓度增大到一定程度(PS/PU质量比为50∶100)时,粒子不稳定而发生聚集.     

Synthesis of Octylmethoxycinamate-silica Core-shell Nanoparticles with Self-templating Method

A self-templating method was employed to synthesize core-shell nanoparticles with octylmethoxycinamate(OMC), a well-known organic UV absorber, as core and nanosilica particles as shell. The characteristic of this method is that the whole process requires neither surface treatment for nanosilica particles nor additional surfactant or stabilizer, and all the reactions could be finished in one-pot, which exempts removing template and reduces reaction steps compared to the conventional process. The morphology, structure, particle size distribution, chemical composition and optical property of OMC-SiO2 nanoparticles were characterized by scanning electron microscopy(SEM), transmission electron microscopy(TEM), dynamic light scattering(DLS), FTIR spectrometry and UV absorption spectrometry, respectively. Experiment results indicate that the resulting OMC-SiO2 nanoparticles were perfectly spherical with smooth particle surfaces, and had clear core-shell structures. The particle size could be tuned by altering reaction conditions. In addition, the mechanism of the self-templating method for forming core-shell nanoparticles was discussed.     

Polypyrrole-palladium nanocomposite coating of micrometer-sized polymer particles toward a recyclable catalyst

A range of near-monodisperse, multimicrometer-sized polymer particles has been coated with ultrathin overlayers of polypyrrole-palladium (PPy-Pd) nanocomposite by chemical oxidative polymerization of pyrrole using PdCl(2) as an oxidant in aqueous media. Good control over the targeted PPy-Pd nanocomposite loading is achieved for 5.2 μm diameter polystyrene (PS) particles, and PS particles of up to 84 μm diameter can also be efficiently coated with the PPy-Pd nanocomposite. The seed polymer particles and resulting composite particles were extensively characterized with respect to particle size and size distribution, morphology, surface/bulk chemical compositions, and conductivity. Laser diffraction studies of dilute aqueous suspensions indicate that the polymer particles disperse stably before and after nanocoating with the PPy-Pd nanocomposite. The Fourier transform infrared (FT-IR) spectrum of the PS particles coated with the PPy-Pd nanocomposite overlayer is dominated by the underlying particle, since this is the major component (>96% by mass). Thermogravimetric and elemental analysis indicated that PPy-Pd nanocomposite loadings were below 6 wt %. The conductivity of pressed pellets prepared with the nanocomposite-coated particles increased with a decrease of particle diameter because of higher PPy-Pd nanocomposite loading. "Flattened ball" morphologies were observed by scanning/transmission electron microscopy after extraction of the PS component from the composite particles, which confirmed a PS core and a PPy-Pd nanocomposite shell morphology. X-ray diffraction confirmed the production of elemental Pd and X-ray photoelectron spectroscopy studies indicated the existence of elemental Pd on the surface of the composite particles. Transmission electron microscopy confirmed that nanometer-sized Pd particles were distributed in the shell. Near-monodisperse poly(methyl methacrylate) particles with diameters ranging between 10 and 19 μm have been also successfully coated with PPy-Pd nanocomposite, and stable aqueous dispersions were obtained. The nanocomposite particles functioned as an efficient catalyst for the aerobic oxidative homocoupling reaction of 4-carboxyphenylboronic acid in aqueous media for the formation of carbon-carbon bonds. The composite particles sediment in a short time (相似文献   

Time-resolved small-angle X-ray scattering studies of polymer-silica nanocomposite particles: initial formation and subsequent silica redistribution

Small angle X-ray scattering (SAXS) is a powerful characterization technique for the analysis of polymer-silica nanocomposite particles due to their relatively narrow particle size distributions and high electron density contrast between the polymer core and the silica shell. Time-resolved SAXS is used to follow the kinetics of both nanocomposite particle formation (via silica nanoparticle adsorption onto sterically stabilized poly(2-vinylpyridine) (P2VP) latex in dilute aqueous solution) and also the spontaneous redistribution of silica that occurs when such P2VP-silica nanocomposite particles are challenged by the addition of sterically stabilized P2VP latex. Silica adsorption is complete within a few seconds at 20 °C and the rate of adsorption strongly dependent on the extent of silica surface coverage. Similar very short time scales for silica redistribution are consistent with facile silica exchange occurring as a result of rapid interparticle collisions due to Brownian motion; this interpretation is consistent with a zeroth-order Smoluchowski-type calculation.     

壳层可控导电聚吡咯/聚苯乙烯复合微球及聚吡咯中空微胶囊的制备

在导电聚合物含量较小时,含核壳结构的导电聚合物复合粒子就可以具有和本体相当的导电率,且加工性好,近年来这种核壳结构微粒的制备已引起了科学家们的广泛关注．Armes等[制备了导电聚吡咯、导电聚苯胺包覆聚苯乙烯的核壳结构胶体粒子及聚苯胺和二氧化硅的纳米复合物．刘正平等用改进的方法在粒径为116nm的单分散聚苯乙烯乳胶粒子上包覆聚吡咯,     

All-acrylic film-forming colloidal polymer/silica nanocomposite particles prepared by aqueous emulsion polymerization

The efficient synthesis of all-acrylic, film-forming, core-shell colloidal nanocomposite particles via in situ aqueous emulsion copolymerization of methyl methacrylate with n-butyl acrylate in the presence of a glycerol-functionalized ultrafine silica sol using a cationic azo initiator at 60 °C is reported. It is shown that relatively monodisperse nanocomposite particles can be produced with typical mean weight-average diameters of 140-330 nm and silica contents of up to 39 wt %. The importance of surface functionalization of the silica sol is highlighted, and it is demonstrated that systematic variation of parameters such as the initial silica sol concentration and initiator concentration affect both the mean particle diameter and the silica aggregation efficiency. The nanocomposite morphology comprises a copolymer core and a particulate silica shell, as determined by aqueous electrophoresis, X-ray photoelectron spectroscopy, and electron microscopy. Moreover, it is shown that films cast from n-butyl acrylate-rich copolymer/silica nanocomposite dispersions are significantly more transparent than those prepared from the poly(styrene-co-n-butyl acrylate)/silica nanocomposite particles reported previously. In the case of the aqueous emulsion homopolymerization of methyl methacrylate in the presence of ultrafine silica, a particle formation mechanism is proposed to account for the various experimental observations made when periodically sampling such nanocomposite syntheses at intermediate comonomer conversions.     

Preparation and characterization of polypyrrole-silica colloidal nanocomposites in water-methanol mixtures

The effect of methanol cosolvent on the synthesis of polypyrrole-silica colloidal nanocomposites using ultrafine silica sols in combination with both FeCl3 and APS oxidants has been investigated. Two protocols were evaluated: the addition of methanol to an aqueous silica sol and the addition of water to a methanolic silica sol. The latter protocol proved to be more robust, since it allowed colloidally stable dispersions to be prepared at higher methanol content (up to 50 vol% using the APS oxidant). This allowed greater control over the particle size of the nanocomposite particles. In general, the spectroscopic data, the particle size range, silica contents and electrical conductivities of these nanocomposites were similar to those reported earlier for purely aqueous formulations. Polypyrrole contents ranged from 49 to 71% by mass and particle diameters varied from around 160 to 360 nm. In terms of colloid stability, the APS oxidant was preferred for nanocomposite syntheses in the presence of methanol. However, the FeCl3 oxidant generally gave higher conductivities and narrower size distributions under comparable conditions. HF etching experiments combined with transmission electron microscopy studies indicated that, to a first approximation, these nanocomposite particles had core-shell morphologies, with a hydrophobic polypyrrole core and a hydrophilic silica shell that compose approximately one monolayer of silica sol particles. Finally, aqueous electrophoresis measurements suggested that the polypyrrole-silica nanocomposites were silica-rich and that the methanolic silica sol was more hydrophobic (lower surface charge density) than the aqueous silica sol.     

Preparation and characterization of a novel nanocomposite particles via in situ emulsion polymerization of vinyl functionalized silica nanoparticles and vinyl acetate

A new class of poly(vinyl acetate) (PVAc)/silica nanocomposite particles was successfully prepared in aqueous solution through a facile synthetic process. First, vinyl functionalized silica nanoparticles (VFSs) were synthesized using one-step method in aqueous emulsion, and then the vinyl groups located on the surface of VFSs were used to induced in situ polymerization of vinyl acetate. Scanning electron microscopy (SEM) images showed that VFSs and PVAc/silica nanocomposite particles all revealed highly monodispersed and uniform spheres. Especially, PVAc/silica nanocomposite particles obtained from transmission electron microscopy images presented an obvious core–shell structure, and the thickness of PVAc shell grafting on the surface of VFSs core was about 17 nm. In addition, the influence of the hydrolyzed and condensed time of vinyl triethoxysilane on the size and size distribution of VFSs was also investigated. The results of dynamic light scattering and SEM analysis indicated that the size and size distribution of VFSs decreased gradually with the extension of the reaction time from 6 to 48 h. Moreover, the structures and thermal properties of the samples were characterized via FT-IR and heat-flow DSC–TG.     

Preparation of novel silica-cadmium sulfide composite nanoparticles having adjustable void space by size-selective photoetching

The size-selective photoetching technique was used to control the size of a CdS nanoparticle inside a silica shell. With monochromatic light irradiation, the diffuse reflectance spectra of silica-coated CdS nanoparticles were blue-shifted, and the size of the resulting CdS nanoparticles incorporated in the silica shells was adjustable by varying the wavelength of irradiated light. TEM observation revealed that the original CdS nanoparticle seemed to be in close contact with the amorphous silica shell to leave almost no clearance, while the monochromatic light irradiation caused the decrease in the size of CdS particles, resulting in the formation of a void space between the photoetched CdS core particle and the silica shell. The average void spaces available in the shells were calculated to be ca. 1.4 and 2.4 nm with the irradiation at 514 and 458 nm, respectively. These results indicated that the size-selective photoetching technique enables the regulation of void space formed in the core-shell structure by choosing the wavelength of irradiation light.     

Preparation of multilayered gold-silica-polystyrene core-shell particles by seeded polymerization

A preparation method for multilayered gold-silica-polystyrene core-shell composite particles is proposed. The gold-silica core-shell particles of 192-nm-sized, synthesized by coating the 18-nm-sized gold particles with silica by a seeded growth technique, were used as cores for succeeding polystyrene coating. After surface modification of gold-silica composite particles by methacryloxypropyltrimethoxysilane (MPTMS), polymerizations of styrene (0.16-0.4 M) were conducted with 8 x 10(-3) M of potassium persulfate initiator in the presence of 1 x 10(-3) M of sodium p-styrenesulfonate anionic monomer. Multilayered core-shell gold-silica-polystyrene particles that contained a single core could be obtained. The coefficient of variation of size distribution (CV) of the composite particles was less than 7%, and polystyrene shell thickness was in a range of 193 to 281 nm.     

核/壳乳液聚合工艺中乳化剂的定量研究

以十二烷基硫酸钠(SDS)为乳化剂,采用多步种子乳液聚合方法制备了核/壳结构乳液,研究了乳化剂加入量以及加料速率对核壳乳液聚合的影响,并推导了核及壳乳液聚合阶段所需乳化剂量的计算公式.研究表明,当种子、核、壳乳液聚合阶段单体量分别为12g、50g和50g,种子乳液聚合阶段加入的乳化剂量为0.44g时,控制核、壳乳液聚合阶段乳化剂的加入量分别在0.64～2.07g及0.04～2.12g之间,且预乳化单体的滴加速度低于2.3g/min时,可以防止二次成核及新乳胶粒子的形成,制得粒径分布窄、核/壳结构明显的乳胶粒子.利用透射电镜(TEM)对所制备的核壳结构乳胶粒子的结构形态进行了验证,试验结果与理论预测结果一致.     

Synthesis of Core-Shell Particles of Polystyrene and Poly(methyl methacrylate) Using Emulsion Photopolymerization

Summary: Submicron core-shell particles of polystyrene (PS) and polystyrene-co-poly(methyl methacrylate) (PS-co-PMMA) coated with PMMA were obtained by emulsion photopolymerization. The seeds of PS or PS-co-PMMA were prepared by emulsion polymerization with or without emulsifier and a ratio of functional monomer and crosslinker (SVBS/EDGMA) in order to obtain different surfaces for the subsequent coating with PMMA. At each stage, the evolution of the average particle size were monitored by using photon correlation spectroscopy (DLS) and the final polymer particles was analyzed via transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The core-shell morphology was identified as the increase of the average particle size in the second stage by DLS technique and by the direct observation by TEM of the differentiation between PS core and PMMA shell, and by the presence of two glass transition temperatures (T_g) as a consequence of the existence of two partially miscible phases.     

Synthesis of SiO2/polystyrene nanocomposite particles via miniemulsion polymerization

The SiO(2)/polystyrene nanocomposite particles were synthesized through miniemulsion polymerization by using sodium lauryl sulfate surfactant (SLS), hexadecane costabilizer in the presence of silica particles coated with methacryloxy(propyl)trimethoxysilane. Core-shell or other interesting morphology composite particles were obtained depending on the size of the silica particles and the surfactant concentration employed. By adjusting these parameters, it was possible to control the size and morphology of the composite particles.     

DESIGN AND CONTROL OF SOAP-FREE HYDROPHILIC-HYDROPHOBIC CORE-SHELL LATEX PARTICLES WITH HIGH CARBOXYL CONTENT IN THE CORE OF THE PARTICLES

Soap-free hydrophilic-hydrophobic core-shell latex particles with high carboxyl content in the core of the particles were synthesized via the seeded emulsion polymerization using methyl methacrylate(MMA),butyl acrylate(BA), methacrylic acid(MAA),styrene(St)and ethylene glycol dimethacrylate(EGDMA)as monomers,and the influences of MMA content used in the core preparation on polymerization,particle size and morphology were investigated by transmission electron microscopy,dynamic light scattering and conductometric titration.The results showed that the seeded emulsion polymerization could be carried out smoothly using "starved monomer feeding process" when MAA content in the core preparation was equal to or less than 24 wt%,and the encapsulating efficiency of the hydrophilic P(MMA-BA-MAAEGDMA) core with the hydrophobic PSt shell decreased with the increase in MAA content.When an interlayer of P(MMAMAA -St)with moderate polarity was inserted between the P(MMA-BA-MAA-EGDMA)core and the PSt shell,well designed soap-free hydrophilic-hydrophobic core-shell latex particles with 24 wt%MAA content in the core preparation were obtained.     

Characterization of the nanomorphology of polymer-silica colloidal nanocomposites using electron spectroscopy imaging

The internal nanomorphologies of two types of vinyl polymer-silica colloidal nanocomposites were assessed using electron spectroscopy imaging (ESI). This technique enables the spatial location and concentration of the ultrafine silica sol within the nanocomposite particles to be determined. The ESI data confirmed that the ultrafine silica sol was distributed uniformly throughout the poly(4-vinylpyridine)/silica nanocomposite particles, which is consistent with the "currant bun" morphology previously used to describe this system. In contrast, the polystyrene/silica particles had a pronounced "core-shell" morphology, with the silica sol forming a well-defined monolayer surrounding the nanocomposite cores. Thus these ESI results provide direct verification of the two types of nanocomposite morphologies that were previously only inferred on the basis of X-ray photoelectron spectroscopy and aqueous electrophoresis studies. Moreover, ESI also allows the unambiguous identification of a minor population of polystyrene/silica nanocomposite particles that are not encapsulated by silica shells. The existence of this second morphology was hitherto unsuspected, but it is understandable given the conditions employed to synthesize these nanocomposites. It appears that ESI is a powerful technique for the characterization of colloidal nanocomposite particles.     

亚微米级聚苯乙烯/聚硅氧烷核壳粒子的制备及其应用

以乳液聚合制备的聚苯乙烯乳液为种子,加入甲基三甲氧基硅烷(MTMS)水解溶液进行缩聚反应,合成亚微米级聚苯乙烯/聚硅氧烷核壳粒子,并以此作为光散射剂添加至聚甲基丙烯酸甲酯(PMMA)树脂中,制备了光散射材料;考察了亚微米级核壳粒子添加在PMMA树脂中的分散性。结果表明:经过双螺杆剪切作用的挤出加工后,可以实现核壳粒子在PMMA树脂中的良好分散。核壳粒子可以大幅度提高PMMA的雾度,当聚苯乙烯/聚硅氧烷核壳粒子(NS82)的含量为1%时,制得的PMMA样片(厚度为2 mm)的雾度为89%,透光率为69%,有效光散射系数为61%。