Magnetoelectric Bi3.25Nd0.75Ti3O12–La0.6Ca0.4MnO3 composite thin films derived by SOL–GEL method

Magnetoelectric (ME) Bi_3.25Nd_0.75Ti₃O₁₂–La_0.6Ca_0.4MnO₃ (BNT–LCMO) composite thin films were deposited on Pt/Ti/SiO₂/Si(100) substrates by a simple SOL–GEL method and spin-coating process with two different deposition sequences: BNT/LCMO/Pt/Ti/SiO₂/Si(BLP) and LCMO/BNT/Pt/Ti/SiO₂/Si(LBP). Our results show the composite thin films exhibit both good ferroelectric and magnetic properties, as well as a ME effect. BLP thin films have larger maximum ME voltage coefficient values than LBP structured thin films. The deposition sequence has a notable effect on the ferroelectric and magnetic properties and ME coupling behavior of the bi-layer thin films.     

Preparation and characterization of nanostructured Ni(OH)2 and NiO thin films by a simple solution growth process

Nanostructured Ni(OH)2 thin films were prepared by a simple solution growth process with F(-) and NH3 used as Ni2+ coordination agents, and ammonia hydroxide solution used as OH(-) supplier to accelerate the hydrolyzation of nickel complex species. The results showed Ni(OH)2 thin films were constructed mainly with hexagonal beta-Ni(OH)2 nanorods; the F(-) and NH3 in reactive solutions played important roles in the film growth process; and solution pH had great influence on the morphologies of thin films, which was explained by the competition of Ni(OH)2 nucleation and growth in solutions. NiO crystallinity thin films were obtained by annealing Ni(OH)2 thin films at 400 degrees C for 2 h and the morphologies of the Ni(OH)2 thin films were sustained well during the annealed process.     

Fabrication and properties of thermosensitive organic/inorganic hybrid hydrogel thin films

We report on a facile method for fabricating thermosensitive organic/inorganic hybrid hydrogel thin films from a cross-linkable organic/inorganic hydrid copolymer, poly[ N-isopropylacrylamide- co-3-(trimethoxysilyl)propylmethacrylate] [P(NIPAm- co-TMSPMA)]. Fourier transform infrared (FT-IR) spectra confirmed the formation of hybrid hydrogel thin films after hydrolysis of the methoxysilyl groups (Si-O-CH 3) and subsequent condensation of the silanol groups (Si-OH). Atomic force microscopy (AFM) images revealed that the surface morphology of the hydrogel thin films depended on the supporting substrates. Microdomains were observed for the hydrogel thin films on a gold surface, which can be attributed to inhomogeneous network structures. The thermoresponsive swelling-deswelling behavior and the viscoelastic properties of the hydrogel thin films were investigated as a function of temperature (25-45 degrees C) by using a quartz crystal microbalance (QCM) operated in water. The high frequency shear modulus of the P(NIPAm- co-TMPSMA) hydrogel thin films was several hundred kilopascals.     

Novel colorimetric sensor for mercury (Ⅱ) based on layer-by-layer assembly of unmodified silver triangular nanoplates

A simple layer-by-layer deposition technique was used to fabricate the multilayer thin films of unmodified silver triangular nanoplates(AgTNPs).The multilayer of AgTNPs thin films were fabricated by alternate deposition of each anionic sodium citrate stabilized AgTNPs and cationic poly(diallyldimethylammonium chloride).All prepared AgTNPs multilayer thin films were exhibited a strong plasmon band at the wavelength of 667 nm,which confirmed the formation of AgTNPs onto the substrate.The characteristics of the multilayer thin films were investigated using contact angle measurement,UV-visible spectroscopy,X-ray diffraction analysis(XRD),atomic force microscope(AFM)and field emission scanning electron microscope(FESEM).As these films are to be used as a mercury(II)colorimetric sensor,the changes in optical properties of the films were evaluated for various mercury(Ⅱ)concentrations.AgTNPs assembled into thin films showed a strong color shift from blue to mauve and colorless when exposed to mercury(Ⅱ).The constructed multilayer thin films exhibited excellent color changes of mercury(II) with a linear range between 0.5 and 20 ppm.The limit of detection(LOD) and limit of quantitation(LOQ) were 0.45 ± 0.002 and 1.52 ± 0.002 ppm,respectively.The recovery values of AgTNPs multilayer thin films are satisfactory in the range of 100.1%-106.4%when applied to determining mercury(Ⅱ) in water samples.     

宽带隙Cu(In,Al)Se2薄膜的制备及表征

以特殊脉冲电沉积方法制备CuInSe2(CIS)前驱体薄膜, 通过真空蒸镀法在CIS薄膜上沉积Al膜, 经硒化退火后在氧化铟锡(ITO)基底上制备了Cu(InAl)Se2(CIAS)薄膜. 采用扫描电子显微镜(SEM)、X射线能谱(EDS)、X射线衍射(XRD)、X射线光电子能谱(XPS)、紫外-可见吸收光谱(UV-Vis)对其形貌、结构、成分及光学吸收性质进行了表征. 结果表明, 制备的CIAS薄膜颗粒均匀, 表面平整致密, 呈黄铜矿结构. 薄膜在可见光区具有良好的吸收, 带隙约为1.65 eV.     

纳米二氧化钒薄膜的制备及红外光学性能

采用双离子束溅射方法在Si3N4/SiO2/Si基底表面沉积氧化钒薄膜, 在氮气气氛下热处理获得二氧化钒薄膜. 利用X射线衍射(XRD)、扫描电子显微镜(SEM)和X射线光电子能谱(XPS)研究了热处理温度对氧化钒薄膜晶体结构、表面形貌和组分的影响, 利用傅里叶变换红外光谱(FT-IR)对二氧化钒薄膜的红外透射性能进行了测试分析. 结果表明, 所制备的氧化钒薄膜以非晶态V2O5和四方金红石结构VO2为主, 经400 ℃、2 h热处理后获得了(011)择优取向的单斜金红石结构纳米VO2薄膜, 提高热处理温度至450 ℃, 纳米结构VO2薄膜的晶粒尺寸减小. FT-IR结果显示,纳米VO2薄膜透射率对比因子超过0.99, 高温关闭状态下透射率接近0. 小晶粒尺寸纳米VO2薄膜更适合在热光开关器件领域应用.     

Photophysical property and photostability of J-aggregate thin films of thiacyanine dyes prepared by the spin-coating method

By use of electrostatic interactions of dye molecules and poly(diallyldimethylammonium chloride) (PDDA), the spin-coating technique has been successfully applied to the preparation of stable J-aggregate thin films of thiacarbocyanine dyes on a polycarbonate or quartz plate. The J-aggregate thin films were prepared by the spin-coating of PDDA aqueous solution on dye thin films prepared on a substrate by the spin-coating of 2,2,3,3-tetrafluoro-1-propanol solution of dyes. Photophysical properties of the dye thin films and J-aggregate thin films were studied by measuring the fluorescence spectra, quantum yields, and lifetimes. Coherent size of the J-aggregates was estimated to be 3-12 by means of the absorption bandwidth (full width at half maximum) or radiative lifetime. Photostability of the J-aggregate thin films was also studied in terms of photodegradation efficiency under argon and oxygen in comparison with the dye thin films, and J-aggregate thin films were found to be more stable than the corresponding dye thin films.     

聚苯乙烯/聚二甲基硅氧烷嵌段共聚物的表面形态研究

采用原子力显微镜(AFM)和透射电镜(TEM)研究了聚苯乙烯/聚二甲基硅氧烷嵌段共聚物(PS-b-PDMS)薄膜的相形态.结果表明,当采用甲苯作为溶剂,旋转涂膜的薄膜样品呈现网络状的形态分布在表面,而样品所对应的透射电镜照片中,PDMS相作为球状分布在PS的连续相中.退火温度对共聚物表面形态有一定的影响,当退火温度高于PDMS的玻璃化温度,表面中PDMS相增多.PS-b-PDMS嵌段共聚物的表面形态随着所用溶剂的变化而有所不同,当采用甲苯作为溶剂时,样品的PS相形成凹坑分布在PDMS的相区之中,而采用环己烷作为溶剂时,PS相作为突起分布在PDMS相区之中.另外,基底对共聚物薄膜表面形态的有较大的影响,当采用硅晶片作为基底时,样品中的PDMS相和PS相呈现近似平行于表面的层状结构.     

"Contact" of nanoscale stiff films

We investigated the contact behaviors of a nanoscopic stiff thin film bonded to a compliant substrate and derived an analytical solution for determining the elastic modulus of thin films. Microscopic contact deformations of the gold and polydopamine thin films (<200 nm) coated on polydimethylsiloxane elastomers were measured by indenting a soft tip and analyzed in the framework of the classical plate theory and Johnson-Kendall-Roberts (JKR) contact mechanics. The analysis of this thin film contact mechanics focused on the bending and stretching resistance of thin films and is fundamentally different from conventional indentation measurements where the focus is on the fracture and compression of the films. The analytical solution of the elastic modulus of nanoscopic thin films was validated experimentally using 50 and 100 nm gold thin films coated on polydimethylsiloxane elastomers. The technical application of this analysis was further demonstrated by measuring the elastic modulus of thin films of polydopamine, a recently discovered biomimetic universal coating material. Furthermore, the method presented here is able to quantify the contact behaviors of nanoscopic thin films, effectively providing fundamental design parameters, the elastic modulus, and the work of adhesion, crucial for transferring them effectively into practical applications.     

富勒醇与阳离子聚电解质复合薄膜的制备与表征

采用静电自组装技术制备了富勒醇与聚对亚苯亚乙烯基 (PPV)的前驱体、聚二烯丙基二甲基氯化铵(PDDA)的复合薄膜 ,利用紫外 可见光吸收光谱 (UV Vis)、原子力显微镜 (AFM )、透射电镜 (TEM)和X射线光电子能谱 (XPS)对薄膜进行了表征 .UV Vis吸收光谱显示 ,在特定波长下自组装薄膜的吸光度与薄膜的双层数成线性关系 ,组装过程具有一致性与重复性 .AFM图象显示富勒醇组装到基片表面后形成直径为几十到10 0多nm的团簇 .富勒醇溶液过滤后组装薄膜 ,薄膜具有较好的均匀性 ;富勒醇溶液不经过滤 ,直接组装薄膜 ,将在薄膜中引入C6 0 晶粒 .XPS分析结果提示C6 0 被羟基修饰并通过静电吸引机制与阳离子聚电解质组装成膜 .富勒醇与PPV的前驱体、PDDA具有很好的自组装性能 ,膜层间的结合力较强 ,所组装的薄膜具有较高的牢固度 .     

TiO2-MoO3复合纳米管阵列薄膜的制备及其可见光活性

通过阳极氧化的方法制备TiO₂纳米管薄膜, 在MoO₃存在的条件下对该薄膜进行热处理得到TiO₂-MoO₃复合纳米管阵列薄膜. 利用X射线衍射(XRD), 扫描电子显微镜(SEM), X射线光电子能谱(XPS), 电化学阻抗谱(EIS), Mott-Schottky 及光电化学方法对得到的薄膜进行了表征. XRD结果表明, TiO₂-MoO₃复合纳米管薄膜中的TiO₂主要为锐钛矿晶型. SEM实验证实了薄膜纳米管结构的存在, 样品中的MoO₃均匀地分散在TiO₂纳米管表面. 利用XPS方法分析了TiO₂-MoO₃复合纳米管薄膜元素的组成, 结果表明, MoO₃在TiO₂表面形成TiO₂-MoO₃复合纳米管薄膜. 研究了热处理温度以及热处理时间对样品的光电化学性能的影响, 相对于单纯TiO₂纳米管薄膜, 适量引入MoO₃提高了样品在可见光区的光电响应能力, 样品的平带电位负移. 在450 °C热处理60 min制得的TiO₂-MoO₃复合半导体纳米管阵列薄膜光电响应活性最高.     

二氧化硅纳米粒子薄膜的制备及光学性能

以二氧化硅胶体和聚二烯丙基二甲基氯化铵(PDDA)为原料,利用静电自组装技术制备了PDDA/SiO2复合薄膜. TEM图象显示,薄膜中的SiO2纳米粒子为密堆积,薄膜均匀、致密;电子衍射实验结果显示,所组装的薄膜为非晶态膜.载玻片表面组装SiO2纳米粒子薄膜后,透射率随薄膜双层数增加呈现周期变化.薄膜具有增透作用,载玻片双面组装薄膜后在一定波长范围内的透射率可提高5％以上. PDDA/SiO2复合薄膜的光学性质主要由SiO2纳米粒子决定,每一双层的平均物理厚度小于SiO2纳米粒子的粒径,薄膜中存在层间穿插现象,逐层组装的复合薄膜具有单层光学薄膜的特性.     

掺钠钼电极在硒化铜铟镓(CIGS)太阳能薄膜电池应用

适量钠元素对铜铟镓硒薄膜生长具有促进作用,本文主要研究了掺钠钼电极特性及其对铜铟镓硒薄膜太阳能电池性能的影响。利用磁控溅射方法制备不同厚度的钼钠/钼(Mo Na/Mo)薄膜作为背电极,并在(Mo Na/Mo)薄膜电极上蒸镀铜铟镓硒(CIGS)薄膜,并利用单质硒源硒化处理后制备CIGS薄膜电池。SEM和XRD结果表明采用三层叠层Mo/Mo/Mo Na薄膜做电极的Mo Na容易被氧化,电阻率增加,采用四层叠层Mo/Mo/Mo Na/Mo薄膜电极方式有效降低电阻率,阻止Mo Na被氧化,CIGS晶粒较大且致密。在同一条件下,在不同Mo Na/Mo厚度电极上制备CIGS薄膜电池,80 nm Mo Na厚度上的CIGS薄膜电池效率达6.54%。     

LaNiO3衬底上Pb(ZrxTi1－x)O3铁电薄膜及梯度薄膜的制备和研究

报道了在镍酸镧 (LaNiO₃, 简称LNO)衬底上锆钛酸铅 [Pb(Zr_xTi_1－x)O₃, 简称PZT]铁电薄膜及其成分梯度薄膜的结构、介电性能、铁电性能以及热释电性能. 首先通过金属有机化合物热分解(MOD)法在Si(100)基片上制备出LaNiO₃, 薄膜, 再通过溶胶-凝胶(sol-gel)法, 在LNO/Si(100)衬底上制备出Pb(Zr_0.80Ti_0.20)O₃, [PZT(80/20)]和Pb(Zr_0.20Ti_0.80)O₃, [PZT(20/80)]铁电薄膜及其成分梯度薄膜. 经俄歇微探针能谱仪(AES)对制备的梯度薄膜进行了成分深度分析, 结果证实成分梯度的存在. 经XRD分析表明, 制备的梯度薄膜为四方结构和三方结构的复合结构, 但其晶面存在一定的结构畸变. 经介电频谱测试表明, 梯度薄膜的介电常数比每个单元的介电常数要大, 但介电损耗相近. 在10 kHz下, 梯度薄膜的介电常数和介电损耗分别为317和0.057. 经电滞回线的测试表明, 梯度薄膜的剩余极化强度比每个单元都大, 而矫顽场却明显较小. 梯度薄膜的剩余极化强度和矫顽场分别为29.96 μC•cm^-2 和54.12 kV•cm^－1. 经热释电性能测试表明, 室温下梯度薄膜的热释电系数为5.54×10-8 C•cm^－2•K^－1, 高于每个单元的热释电系数.     

Compositional and structural engineering of DNA multilayer films

We report the layer-by-layer (LbL) preparation of multilayered thin films that consist solely of DNA. The properties of the films were varied by assembling the layers from different oligonucleotide building blocks, which are composed of repeating homopolymeric units of nucleotides [adenosine (A), cytosine (C), guanine (G), and thymidine (T)] or "random" sequences. Films assembled from oligonucleotides with a single complementary unit did not show continual layer buildup. To form a repeating multilayer system, it was necessary for single-stranded DNA to be available for subsequent layers to hybridize. By using oligonucleotides with multiple nucleotide units, multilayer films were successfully assembled. We demonstrate that the thickness and swellability of the films can be controlled by the extent of hydrogen bonding (the G/C content of the oligonucleotide) and orientation of the oligomers. We have examined the stability and swellability of the films in solutions of varying salt concentration as well as in a denaturing urea solution. Stable, hollow DNA capsules were also formed by preparing the films on sacrificial colloidal templates, followed by removal of the core. The assembly of propagating structures through DNA hybridization paves the way for the engineering of DNA films with tailored composition, structure, and permeability, making them likely to find application in drug/gene delivery and biomolecular sensing.     

沉积电位对电沉积ZnS薄膜的影响

采用电沉积方法,在不同沉积电位条件下,在氧化锡铟(ITO)导电玻璃上沉积制备了ZnS薄膜,利用XRD、SEM和UV-VIS测试技术对在不同沉积电位所制备薄膜的晶相结构、表面微观形貌和光学性能进行了表征.研究结果表明:沉积电位在1.5 V—1.7 V范围内制备的ZnS薄膜呈非晶态,其可见光透过率从60 %降低到20 %,薄膜的光学带隙约为3.97 eV.在沉积电位为2.0 V条件下所沉积薄膜为ZnS结晶相和金属Zn混合相,薄膜透过率显著降低.     

Vanadium(IV) oxide thin films on glass and silicon from the atmospheric pressure chemical vapour deposition reaction of VOCl3 and water

The dual source atmospheric pressure chemical vapour deposition (APCVD) reaction of VOCl₃ and H₂O was used to prepare thin films of vanadium oxides on glass and silicon substrates. The thin films were characterised by X-ray diffraction, Raman spectroscopy X-ray photoelectron spectroscopy and scanning electron microscopy. At reactor temperatures above 600 °C with a gas-phase excess of water over VOCl₃, vanadium(IV) oxide thin films were produced which show a thermochromic transition temperature of 67 °C. The APCVD process is directly compatible with high throughput float-glass production enabling the use of a thin film of VO₂ as an intelligent window coating. With reactor temperatures below 600 °C or with a gas-phase excess of VOCl₃ over water, V₂O₅ thin films were produced. Vanadium(IV) oxide thin films could also be prepared on silicon substrates from the APCVD reaction of VOCl₃ and H₂O, which opens up further technological applications for the APCVD of VO₂ thin films.     

Studies of photosensitive alignment layer based on ladder‐like polysilsequioxane liquid‐crystal devices using atomic force microscopy/force curve

Atomic force microscopy (AFM)/force curve measurements were used to study the photochemical process of UV‐treated (0, 10, 20, 30 and 60 min) organic thin films that were prepared from azobenzene and cinnamate side‐chain co‐grafted ladder‐like polysilsequioxanes (LPS). The morphological data of the thin films describe the changing process on the surface of the thin film. The statistical results of the adhesion force of the thin films further demonstrate the intermolecular characteristics of the thin films. A photosensitive thin film after UV exposure for 20 min would be a better material with a preferred orientation that can be used to make liquid‐crystal devices. Copyright © 2003 John Wiley & Sons, Ltd.     

Improved optical and electrical properties of sol–gel-derived boron-doped zinc oxide thin films

Sol–gel spin-coating was used to grow zinc oxide (ZnO) thin films doped with 0–2.5 at.% B on quartz substrates. The structural, optical, and electrical properties of the thin films were investigated using field-emission scanning electron microscopy, X-ray diffraction (XRD), photoluminescence (PL), ultraviolet–visible spectroscopy, and van der Pauw Hall-effect measurements. All the thin films had deposited well onto the quartz substrates and exhibited granular morphology. The average crystallite size, lattice constants, residual stress, and lengths of the bonds in the crystal lattice of the thin films were calculated from the XRD data. The PL spectra showed near-band-edge (NBE) and deep-level emissions, and B doping varied the PL properties and increased the efficiency of the NBE emission. The optical transmittance spectra for the undoped ZnO and boron-doped zinc oxide (BZO) thin films show that the optical transmittance of the BZO thin films was significantly higher than that of the undoped ZnO thin films in the visible region of the spectra and that the absorption edge of the BZO thin films was blue-shifted. In addition, doping the ZnO thin films with B significantly varied the absorption coefficient, optical band gap, Urbach energy, refractive index, extinction coefficient, single-oscillator energy, dispersion energy, average oscillator strength, average oscillator wavelength, dielectric constant, and optical conductivity of the BZO thin films. The Hall-effect data suggested that B doping also improved the electrical properties such as the carrier concentration, mobility, and resistivity of the thin films.     

Surface morphology and biological activity of protein thin films produced by electrospray deposition

Protein thin films were prepared by the electrospray deposition (ESD) method from aqueous solutions of alpha-lactalbumin (alpha-LA) at different concentrations, and their surface morphologies and biological activities were characterized. The surface morphologies of the deposited films were observed using scanning electron microscopy (SEM) and atomic force microscopy (AFM). The SEM and AFM images showed that the film surfaces had a fine porous structure, in which the pore diameters ranged from 40 to 600 nm. The biological activities of the cross-linked protein films were tested by the mechanochemical method. The response to calcium ion (Ca(2+)) demonstrated that the biological activity of the films was preserved. These results indicate that the ESD method is potentially useful for the fabrication of active protein thin films. The freestanding protein thin films prepared by ESD and postdeposition cross-linking provide novel options for protein-based biomaterials.