Perfecting imperfect "monolayers": removal of siloxane multilayers by CO2 snow treatment

Self-assembled monolayers (SAMs) of N-(3-triethoxysilylpropyl)-4-hydroxybutyramide were prepared on silicon oxide on silicon (Si/SiO(2)). Initial silane adsorption and high-temperature annealing led to a stable base monolayer with many large over-lying islands of disordered multilayers as a result of the non-self-limited growth process. The disordered multilayers were hydrolyzed and subsequently removed by CO(2) snow treatment. The resulting films were one monolayer thick as measured by ellipsometry. Atomic force microscopy, attenuated total reflection Fourier transform infrared spectroscopy, and contact angle analysis showed that the films were composed of monolayers with full and uniform surface coverage rather than nonuniform coverage by islands or patches of multilayers. Monolayers of octadecyltrichlorosilane were also prepared by multilayer removal via CO(2) treatment, showing the general applicability of the technique toward siloxane SAMs. We believe that CO(2) is an excellent solvent for weakly bound and hydrolyzed molecules that compose multilayers, and this ability to prepare near-perfect monolayer films from imperfect ones allows for less stringent formation conditions.     

Tribological properties of self-assembled monolayers of catecholic imidazolium and the spin-coated films of ionic liquids

A novel compound of an imidazolium type of ionic liquid (IL) containing a biomimetic catecholic functional group normally seen in mussel adhesive proteins was synthesized. The IL can be immobilized on a silicon surface and a variety of other engineering material surfaces via the catecholic anchor, allowing the tribological protection of these substrates for engineering applications. The surface wetting and adhesive properties and the tribological property of the synthesized self-assembled monolayers (SAMs) are successfully modulated by altering the counteranions. The chemical composition and wettability of the IL SAMs were characterized by means of X-ray photoelectron spectroscopy (XPS) and contact angle (CA) measurements. The adhesive and friction forces were measured with an atomic force microscope (AFM) on the nanometer scale. IL composite films were prepared by spin coating thin IL films on top of the SAMs. The macrotribological properties of these IL composite films were investigated with a pin-on-disk tribometer. The results indicate that the presence of IL SAMs on a surface can improve the wettability of spin-coated ionic liquids and thus the film quality and the tribological properties. These films registered a reduced friction coefficient and a significantly enhanced durability and load-carrying capacity. The tribological properties of the composite films are better than those of pure IL films because the presence of the monolayers improves the adhesion and compatibility of spin-coated IL films with substrates.     

Hydration of hydrophilic thiolate monolayers visualized by atomic force microscopy

Monolayers of mercaptoundecanol and mercaptoundecanoic acid were prepared on Au(111) films, immersed in aqueous solutions, and probed by frequency-modulation atomic force microscopy. The pN-order tip-surface force was observed over the monolayers as a function of vertical and lateral coordinates, together with the topography of the monolayers. The observed force distribution was modulated between adjacent OH endgroups in the mercaptoundecanol monolayer, as opposed to on top of COOH and COO(-) endgroups in the mercaptoundecanoic acid monolayer. Models of the interfacial hydrogen bond between water and the endgroups were proposed. The force distribution was insensitive to the electrolyte composition. There was no qualitative sign of tip-induced confinement of water.     

Functionalized imidazolium wear‐resistant ionic liquid ultrathin films for MEMS/NEMS applications

As a kind of new material, ionic liquids (ILs) are considered a new type of lubricant for micro/nanoelectromechanical system (M/NEMS) due to their excellent thermal and electrical conductivity. However, so far, only a few reports have investigated the friction and wear of thin films of these materials at the micro scale. Evaluating the nanoscale tribological performance of ILs when applied as films of a few nanometers thickness on a substrate is a critical step for their application in M/NEMS devices. To achieve this purpose, IL thin films with four kinds of anions were synthesized and prepared on single‐crystal silicon wafers by the dip‐coating method. Film thickness was determined by the ellipsometric method. Their surface morphologies were observed by means of atomic force microscopy (AFM). The nano and micro tribological properties of the IL films were investigated by a friction force microscope (FFM)with a spherical probe and a UMT‐2MT tribotester, respectively. The corresponding morphologies of the wear tracks of the IL films were examined using a three‐dimensional non‐contact interferometric microscope. The impact of temperature on the adhesion behavior was studied, as well as the effect of sliding frequency and load on the friction coefficient, load bearing capacity and anti‐wear durability. It was found that friction, adhesion and durability of IL films were strongly dependent on their anionic molecular structures, wettability and ambient environment. Copyright © 2010 John Wiley & Sons, Ltd.     

Substrate-dependent enhancement of the durability of EPD graphene coating as a macroscale solid lubricant

Graphene has exhibited outstanding properties of reducing friction and wear when it is utilized as a novel solid lubricant, while its durability, especially at the macroscale, remains a challenge for robust industrial applications. In this study, we demonstrate a remarkable substrate-dependent enhancement of the durability and load capacity of graphene film prepared with electrophoretic deposition method. The tribological performance of graphene films on four typical engineering material surfaces was examined. Graphene films exhibit highly consistent coefficients of friction ranging from 0.1 to 0.16, decreasing by 76%–87% compared with that obtained for the bare substrates (0.60–0.83). As for durability, graphene films on the stainless steel and titanium alloy substrates show largely enhanced lifetime compared with that on the silicon or cemented carbide substrates. The graphene film on titanium allay can sustain up to 260,000 cycles, 10–20 times longer than that on brittle substrates. Such a remarkably enhanced durability should be attributed to the relatively higher ductility of the substrates and its high adhesion with graphene, which is beneficial for forming a dense layer of graphene-containing tribo-film within the sliding interface. The results of this study may provide a useful guideline for utilizing graphene films as solid lubricants in engineering fields.     

活性端基聚苯乙烯表面修饰膜的制备与摩擦学性能

以巯丙基三甲氧基硅烷为链转移剂 ,利用自由基聚合反应合成了三甲氧基硅烷封端的聚苯乙烯 ,研究了其在单晶硅基底上的自组装行为 ,并用红外、X射线光电子能谱、原子力显微等对膜进行了表征 .研究发现 ,聚合物的浓度大于 1mg mL时才能形成较完整的聚合物膜 ,均方根粗糙度低于 1nm ,自组装过程在 90℃时 1h内即可完成 .与空白基底相比 ,自组装聚苯乙烯膜具有良好的减摩抗磨性能 ,稳定摩擦系数为 0 12 .     

具有不同取代链长的卟啉衍生物LB膜的结构研究

本文研究了三种羧酸取代的四苯基卟啉衍生物在空气/Cd^2^+水溶液界面上所形成的单层膜及LB膜。这三种卟啉衍生物中, 一种没有脂链, 另外两种具有不同长度的脂链。由π-A等温线得到的平均表观分子面积相差很大。紫外-可见光谱表明, LB膜中卟啉的Soret吸收带相对于溶液的吸收均红移, 但红移程度不同。LB膜的偏振紫外-可见光谱表明, LB膜中三种卟啉衍生物的卟啉环具有基本一致的取向。运用亚相降低法得到了三种卟啉衍生物单层LB膜, 其紫外-可见光谱与用垂直提拉法得到的LB膜的紫外-可见光谱具有一致的特征。这些结果表明: 卟啉衍生物有无取代链及取代链长的不同对平均表观分子面积的大小和膜中环间的距离有影响, 但对环的取向没有影响。环的取向由环本身及环上的亲水取代基来确定。气/液界面上三种卟啉衍生物的单层膜中环也具有一致的取向, 且与LB膜中环的取向相差不大。提拉不会对膜中环的取向及膜的结构造成大的改变。     

Marked increase in the binding strength between the substrate and the covalently attached monolayers of zeolite microcrystals by lateral molecular cross-linking between the neighboring microcrystals

Monolayers of cubic zeolite microcrystals (1.7 x 1.7 x 1.7 and 0.3 x 0.3 x 0.3 mum3) were assembled on glass plates through imine- or urethane-linkages between the zeolite-tethered 3-aminopropyl (AP) groups and the glass-bound benzaldehyde or isocyanate groups, which were prepared by treating AP-tethering glass plates with a large excess of terephthaldicarboxaldehyde (TPDA) or 1,4-diisocyanatobutane (DICB), respectively, in toluene. The additional treatment of the monolayers of zeolite microcrystals with TPDA or DICB led to lateral molecular cross-linking between the neighboring, closely packed zeolite microcrystals in the monolayers through AP-TPDA-AP imine or AP-DICB-AP urethane linkages between the zeolite-tethered AP groups and the newly introduced TPDA or DICB, respectively. The comparison of the binding strengths between the glass substrates and the monolayers revealed that the molecular cross-linking leads to as much as 7- and 38-fold (by average) increase in the binding strength in the cases of 1.7 x 1.7 x 1.7 and 0.3 x 0.3 x 0.3 mum3 crystals, respectively. We predict that the effect of lateral cross-linking on the binding strength will further increase with further decreasing the size of the building blocks to nanoparticles and to molecules.     

XPS and AFM characterization of the self‐assembled molecular monolayers of a 3‐aminopropyltrimethoxysilane on silicon surface,and effects of substrate pretreatment by UV‐irradiation

The self‐assembled (SA) molecular monolayers of a 3‐aminopropyltrimethoxysilane (3‐APTS) on a silicon (111) surface, and the effects of ultraviolet (UV) pre‐treatment for substrates on the assembling process have been studied using XPS and atomic force microscopy (AFM). The results show that the SA 3‐APTS molecules are bonded to the substrate surface in a nearly vertical orientation, with a thickness of the monolayer of about 0.8–1.5 nm. The SA molecular monolayers show a substantial degree of disorder in molecular packing, which are believed to result from the interactions of amine tails in the silane molecules used with surface functionalities of the substrates, and the oxygen‐containing species from the ambient. UV irradiation for silicon substrates prior to the self‐assembly reaction can enhance the assembly process and hence, significantly increase the coverage of the monolayer assembled for the substrates. Copyright © 2010 John Wiley & Sons, Ltd.     

Covalently attached monolayers on crystalline hydrogen-terminated silicon: extremely mild attachment by visible light

A very mild method was developed for the attachment of high-quality organic monolayers on crystalline silicon surfaces. By using visible light sources, from 447 to 658 nm, a variety of 1-alkenes and 1-alkynes were attached to hydrogen-terminated Si(100) and Si(111) surfaces at room temperature. The presence and the quality of the monolayers were evaluated by static water contact angles, X-ray photoelectron spectroscopy, and IR spectroscopy. Monolayers prepared by thermal, UV light, or visible light initiation were compared. Additionally, the ability of infrared reflection-absorption spectroscopy to study organic monolayers on silicon was explored. A reaction mechanism is discussed on the basis of investigations of the reaction behavior of 1-alkenes with silicon wafers with varying types and levels of doping. Finally, a series of mixed monolayers derived from the mixed solutions of a 1-alkene and an omega-fluoro-1-alkene were investigated to reveal that the composition of the mixed monolayers was directly proportional to the molar ratio of the two compounds in the solutions.     

Examining the frictional forces between mixed hydrophobic-hydrophilic alkylsilane monolayers

Monolayers presenting methyl-terminated (hydrophobic) and hydroxyl-terminated (hydrophilic) surfaces on silica have been studied by molecular dynamics simulation and the effects of hydrogen bonding, chain length, and chain mixing on the frictional properties determined. The hydroxyl-terminated monolayers were found to show large adhesion zones as a result of strong interfacial interlayer hydrogen bonds; the interfacial sliding forces observed in the hydroxyl-terminated monolayers being one order of magnitude higher than the interfacial forces for the hydrophobic surfaces at the characteristic point of zero-load. Mixed hydroxyl- and methyl-terminated monolayers of equal length were found to exhibit intermediate shear stress values between those observed for pure monolayers, with the magnitude of the shear stress depending on the surface content of the hydroxyl-terminated chains. For mixed monolayers of unequal chain lengths, at high loads a maximum in the magnitude of the shear stress as a function of the length of the methyl-terminated chain was observed due to the creation of a buffer zone between the hydroxyl-terminated chains that produces strong hydrogen-bonding interactions. The effect of a constant normal load or constant separation simulation ensemble on the results has also been studied and in general found to have minimal influence on the observed behavior, although some differences are observed for the shear stress at intermediate normal loads due to the formation of stronger hydrogen bond networks at constant load compared to constant separation.     

Nanoscale patterning of alkyl monolayers on silicon using the atomic force microscope

Self-assembled monolayers (SAMs) of 1-alkenes on hydrogen-passivated silicon substrates were successfully patterned on the nanometer scale using an atomic force microscope (AFM) probe tip. Nanoshaving experiments on alkyl monolayers formed on H-Si(111) not only demonstrate the flexibility of this technique but also show that patterning with an AFM probe is a viable method for creating well-defined, nanoscale features in a monolayer matrix in a reproducible and controlled manner. Features of varying depths (2-15 nm) were created in the alkyl monolayers by controlling the applied load and the number of etching scans made at high applied loads. The patterning on these SAM films is compared with the patterning of alkyl siloxane monolayers on silicon and mica.     

Asymmetric Arrangement of Monolayer in the Multilayer Films of 2-Hydroxy-4,4＇-dihexyloxy-azobenzene

Multilayer films of 2-hydroxy-4,4‘‘-dihexyloxy-azobenzene (HAB) on silicon substrates have been studied with atomic force microscopy, temperature-dependent FTIR, and X-Ray diffraction technique. The results show that the multilayer films are formed by stacking of HAB monolayers via π-π interactions and the adjacent two monolayers in the film are arranged in an asymmetric way in the multilayer films.     

Langmuir-Blodgett film of hydrophobin protein from Pleurotus ostreatus at the air-water interface

We present results concerning the formation of Langmuir-Blodgett (LB) films of a class I hydrophobin from Pleurotus ostreatus at the air-water interface, and their structure as Langmuir-Blodgett (LB) films when deposited on silicon substrates. LB films of the hydrophobin were investigated by atomic force microscopy (AFM). We observed that the compressed film at the air-water interface exhibits a molecular depletion even at low surface pressure. In order to estimate the surface molecular concentration, we fit the experimental isotherm with Volmer's equation describing the equation of state for molecular monolayers. We found that about (1)/ 10 of the molecules contribute to the surface film formation. When transferred on silicon substrates, compact and uniform monomolecular layers about 2.5 nm thick, comparable to a typical molecular size, were observed. The monolayers coexist with protein aggregates, under the typical rodlet form with a uniform thickness of about 5.0 nm. The observed rodlets appear to be a hydrophilic bilayer and can then be responsible for the surface molecular depletion.     

Monolayer behavior of 1,2-dipalmitoylgalloylglycerol, a synthetic lipid with strong cohesive properties

Monolayers of 1,2-dipalmitoylgalloylglycerol (DPGG) were investigated at the air-water interface. The monolayers exhibit high rigidity which leads to the formation of surface tension gradients in the film. Transfer to solid substrate yields homogeneous Langmuir-Blodgett films with low surface roughness. Large numbers of aggregates were observed by Brewster angle microscopy and imaging ellipsometry at relatively high molecular areas. At all pressures, the DPGG molecules adopt conformations corresponding to low tilt angles. Constant area measurements result in a pressure increase as the film rearranges to maximize the intermolecular interactions. An optimal intermolecular distance required for the formation of a hydrogen-bond network between headgroups is proposed to explain the observed, highly cohesive monolayer behavior.     

Alternative method for fabricating chemically functionalized AFM tips: silane modification of HF-treated Si3N4 probes

An alternative method for fabricating functionalized, atomic force microscopy (AFM) tips is presented. This technique is simple and requires only minimal preparation and tip modification to generate chemically sensitive probes that have a robust organic monolayer of flexible terminal chemistry attached to the surface. Specifically, commercially microfabricated Si3N4 AFM tips were modified with self-assembled monolayers (SAMs) of octadecyltrichlorosilane and (11-bromoundecyl)trichlorosilane after removing the native silicon oxide surface layer with concentrated hydrofluoric acid. The structure of these SAM films on solid silicon nitride surfaces was studied using contact angle goniometry and Fourier transform infrared spectroscopy. Pull-off force measurements on various bare (mica, graphite, and silicon) and SAM-functionalized substrates confirm that mechanically robust, long-chain organic silane SAMs can be formed on HF-treated Si3N4 tips without the presence of an intervening oxide layer. Adhesion experiments show that the integrity of the organic film on the chemically modified tips is maintained over repeated measurements and that the functionalized tips can be used for chemical sensing experiments since strong discrimination between different surface chemistries is possible.     

nc-Si:H/c-Si硅异质结太阳电池中本征硅薄膜钝化层的优化

采用射频等离子体增强化学气相沉积(RF-PECVD)法在低温、低功率的条件下制备了一系列本征硅薄膜, 研究了硅烷浓度(C_S)对薄膜微结构、光电特性及表面钝化性能的影响. 将本征硅薄膜作为钝化层应用到氢化纳米晶硅/晶硅(nc-Si:H/c-Si)硅异质结(SHJ)太阳电池中, 研究了硅烷浓度和薄膜厚度对电池性能的影响. 实验发现: 随着硅烷浓度的降低, 本征硅薄膜的晶化率、氢含量、结构因子、光学带隙和光敏性等都在过渡区急剧变化; 本征硅薄膜的钝化性能由薄膜的氢含量及氢的成键方式决定. 靠近过渡区的薄膜具有较好的致密性和光敏性, 氢含量最高, 带隙态密度低, 且主要以SiH 形式成键, 对硅片表现出优异的钝化性能, 使电池的开路电压大幅提高. 但是, 当薄膜的厚度过小时, 会严重影响其钝化质量. 本实验中, 沉积本征硅薄膜的最优硅烷浓度为6% (摩尔分数), 且当薄膜厚度为~8 nm时, 所制备电池的性能最好. 实验最终获得了开路电压为672 mV, 短路电流密度为35.1 mA·cm^-2, 填充因子为0.73, 效率为17.3%的nc-Si:H/c-Si SHJ太阳电池     

Morphological behavior of thin polyhedral oligomeric silsesquioxane films at the molecular scale

Synchrotron X-ray reflectivity (XRR) was used to study the structure of thin films of polyhedral oligomeric silsesquioxanes (POSS) with side organic chains of different flexibility and containing terminal epoxy groups. POSS films were deposited from volatile solvents on hydroxylated and hydrogen-passivated silicon surfaces. The XRR data show a variety of structural morphologies, including autophobic molecular monolayers and bilayers as well as uniform films. The role of conformational and energetic factors governing the development of different morphologies in a restricted geometry is discussed.     

Monolayer behavior and BAM observaion of biphenyl liquid crystalline polysiloxane at the A/W interface

Monolayers of a chiral biphenyl liquid crystalline polysiloxane and its monomer have been studied by π–A isotherms and hysteresis measurements. Both of them can form monolayers at different temperatures. The molecular packing in the monolayers are temperature-dependent for the monomer but not for the polymer. The molecular orderings are dominated by the packing of the biphenyl mesogens. Metastable monolayers with different ordering and thickness of domains have been directly observed by Brewster Angle Microscopy (BAM) in monomer monolayers. Both of them show characteristics of rigid monolayers. A broken process of the monolayers can be observed during expansion.     

Growth kinetics and morphology of self-assembled monolayers formed by contact printing 7-octenyltrichlorosilane and octadecyltrichlorosilane on Si(100) wafers

The growth kinetics and morphologies of self-assembled monolayers deposited by contact printing 7-octenyltrichlorosilane (OCT) and octadecyltrichlorosilane (OTS) on Si(100) were studied by ellipsometry and atomic force microscopy. We found that, for both OCT and OTS, full monolayers could be obtained at room temperature after printing times of 120-180 s; the printing-based monolayer assembly processes follow apparent Langmuir adsorption kinetics, with the measured film growth rates increasing both with the ambient humidity and with concentration of the ink used to load the stamp. At a dew point of 10 degrees C and an ink concentration (in toluene) of 50 mM, the observed film growth rate constant is 0.05 s(-)(1). When the printing was carried out at a lower ambient humidity (dew points of 1-3 degrees C), the measured rates of assembly were approximately a factor of 2 slower. Increasing the deposition temperature from 25 to 45 degrees C under these conditions increased the film growth rate only slightly. The morphology of the films depends on the identity of the ink. Uniform, high-coverage films could be obtained readily from the eight-carbon chain length adsorbate OCT, provided that the stamp was not overloaded with the ink; for high concentrations outside of the optimal range, the surface presented significant numbers of adsorbed particles ascribed, in part, to siloxane polymers formed by hydrolysis of the ink on the stamp before printing. In marked contrast, for the 18-carbon adsorbate OTS, the printed films always consisted of a mixture of a uniform monolayer plus adsorbed polysiloxane particles. The different film morphologies seen for OCT and OTS are proposed to result from the different transfer efficiencies of the organotrichlorosilane relative to polysiloxane hydrolysis products formed during the printing process. These transfer efficiencies exhibit sensitivities related to the permeation of the poly(dimethylsiloxane) (PDMS) stamp by the silane reagents. Short-chain inks such as OCT evidently permeate the PDMS stamp more deeply than longer-chain inks such as OTS. This difference, and the different diffusion rates of ink vs oligomeric silane hydrolysis products, determines the film morphology obtained by contact printing. The mass transfer dynamics of the process thus yield surface layers derived from varying quantities of siloxane oligomers, which subsequently transfer to the substrate along with unhydrolyzed silane adsorbate during the printing step. The structural evolution of the contact-printed films so obtained is strikingly different from that of SAMs prepared by immersion.