Poly(3‐hexylthiophene)‐b‐poly(3‐cyclohexylthiophene): Synthesis,microphase separation,thin film transistors,and photovoltaic applications

We report the synthesis, characterization, microphase separation, field‐effect charge transport, and photovoltaic properties of regioregular poly(3‐hexylthiophene)‐b‐poly(3‐cyclohexylthiophene) (P3HT‐b‐P3cHT). Two compositions of P3HT‐b‐P3cHT (HcH63 and HcH77) were synthesized with weight‐average molecular weights of 155,500 and 210,800 and polydispersity indices of 1.45 and 1.57, respectively. Solvent‐casted HcH77 was found to self‐assemble into nanowires with a width of 12.5 ± 0.9 nm and aspect ratios of 50–120, as observed by TEM imaging. HcH77 and HcH63 annealed 280 °C were observed by small angle X‐ray scattering (SAXS) and wide angle X‐ray scattering (WAXS) to be microphase‐separated with characteristic length scales of 17.0–21.7 nm. The microphase‐separated domains were shown to be crystalline with interlayer backbone (100) d‐spacings of 1.69 and 1.40 nm, which correspond to the P3HT and P3cHT blocks, respectively. Field‐effect transistors fabricated from P3HT‐b‐P3cHT thin films showed a mobility of holes (0.0019 cm²/Vs) which is independent of thermal annealing. Bulk heterojunction solar cells based on HcH77/fullerene (PC₇₁BM) blend thin films had a maximum power conversion efficiency of 2.45% under 100 mW/cm² AM1.5 solar illumination in air. These results demonstrate that all‐conjugated block copolymers are suitable semiconductors for applications in field‐effect transistors and bulk heterojunction solar cells. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 614–626, 2010     

Synthesis of poly(m‐phenylene) and poly(m‐phenylene)‐block‐ poly(3‐hexylthiophene) with low polydispersities

Well‐defined poly(m‐phenylene) (PMP), which is poly(1,3‐dibutoxy‐m‐phenylene), was successfully synthesized via Grignard metathesis polymerization. PMP with a reasonably high number‐average molecular weight (M_n) of 25,900 and a very low polydispersity index of 1.07 was obtained. The polymerization of a Grignard reagent monomer, 1‐bromo‐2,4‐dibutoxy‐5‐chloromagnesiobenzene, proceeded in a chain‐growth manner, probably due to the meta‐substituted design producing a short distance between the MgCl and Br groups and thereby making a smooth nickel species (? C? Ni? C? ) transfer to the intramolecular chain end (? C? Ni? Br) over a benzene ring. PMP showed a good solubility in the common organic solvents, such as tetrahydrofuran, CH₂Cl₂, and CHCl₃. Furthermore, a new block copolymer comprised of PMP and poly(3‐hexylthiophene) was also prepared. The tapping mode atomic force microscopy image of the surface of the block copolymer thin film on a mica substrate showed a nanofibril morphology with a clear contrast. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Synthesis and Thin Film Phase Behaviour of Functional Rod‐Coil Block Copolymers Based on Poly(para‐phenylenevinylene) and Poly(lactic acid)

We report the synthesis of a series of block copolymers consisting of a rod‐like semiconducting poly(2,5‐di(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene) (DEH‐PPV) block and a flexible poly(lactic acid) (PLA) block that can be selectively degraded under mild conditions. Such selectively degradable block copolymers are designed as self‐assembling templates for bulk heterojunction donor–acceptor layers in organic solar cells. A lamellar microphase‐separated domain structure was identified for block copolymers with PLA volume fractions between 29 and 79% in bulk and thin films using SAXS, TEM, and AFM. Depending on the ratio of the two blocks we find either lamellae oriented parallel or perpendicular to the substrate in thin films.

     

Copolymerization of propylene with higher α‐olefins in the presence of the syndiospecific catalyst i‐Pr(Cp)(9‐Flu)ZrCl2/MAO

The catalyst system i‐Pr(Cp)(9‐Flu)ZrCl₂/methylaluminoxane was used for the synthesis of random syndiotactic copolymers of propylene with 1‐hexene, 1‐dodecene, and 1‐octadecene as comonomers. An investigation of the microstructure by ¹³C NMR spectroscopy revealed that the stereoregularity of the copolymers decreased because of an increase in skipped insertions in the presence of the higher 1‐olefin. The melting temperature of the copolymers, as measured by differential scanning calorimetry (DSC), decreased linearly with increasing comonomer content independently of the comonomer nature. During the DSC heating cycle, an exothermic peak indicating a crystallization process was observed. The decrease in the crystallization temperature with higher 1‐olefin content, measured by crystallization analysis fractionation, indicated a small but significant dependence on the nature of the comonomer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 128–140, 2002     

Crystallization and morphology of poly(ethylene oxide‐b‐lactide) crystalline–crystalline diblock copolymers

The crystallization behaviors and morphology of asymmetric crystalline–crystalline diblock copolymers poly(ethylene oxide‐lactide) (PEO‐b‐PLLA) were investigated using differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), and microscopic techniques (polarized optical microscopy (POM) and atomic force microscopy (AFM)). Both blocks of PEO₅‐b‐PLLA₁₆ can be crystallized, which was confirmed by WAXD, while PEO block in PEO₅‐b‐PLLA₃₀ is difficult to crystallize because of the confinement induced by the high glass transition temperature and crystallization of PLLA block with the microphase separation of the block copolymer. Comparing with the crystallization and morphology of PLLA homopolymer and differences between the two copolymers, we studied the influence of PEO block and microphase separation on the crystallization and morphology of PLLA block. The boundary temperature (T_b) was observed, which distinguishes the crystallization into high‐ and low‐temperature ranges, the growth rate and morphology were quite different between the ranges. Crystalline morphologies including banded spherulite, dendritic crystal, and dense branching in PEO₅‐b‐PLLA₁₆ copolymer were formed. The typical morphology of dendritic crystals including two different sectors were observed in PEO₅‐b‐PLLA₃₀ copolymer, which can be explained by secondary nucleation, chain growth direction, and phase separation between the two blocks during the crystallization process. Lozenge‐shaped crystals of PLLA with screw dislocation were also observed employing AFM, but the crystalline morphology of PEO block was not observed using microscopy techniques because of its small size. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1400–1411, 2008     

Self‐assembly of oligo(p‐phenylenevinylene)‐block‐poly(ethylene oxide) in polar media and solubilization of an oligo(p‐phenylenevinylene) homooligomer inside the assembly

Rod–coil amphiphilic diblock copolymers, consisting of oligo(p‐phenylenevinylene) (OPV) as a rod and hydrophobic block and poly(ethylene oxide) (PEO) as a coil and hydrophilic block, were synthesized by a convergent method. The aggregation behavior of the block copolymers in a selective solvent (tetrahydrofuran/H₂O) was probed with the absorption and emission of the OPV block. With increasing H₂O concentration, the absorption maximum was blueshifted, the emission from the molecularly dissolved OPV decreased, and that from the aggregated OPV increased. This indicated that the OPV blocks formed H‐type aggregates in which the OPV blocks aligned in a parallel orientation with one another. The transmission electron microscopy observation revealed that the block copolymers with PEO weight fractions of 41 and 62 wt % formed cylindrical aggregates with a diameter of 6–8 nm and a length of several hundreds nanometers, whereas the block copolymer with 79 wt % PEO formed distorted spherical aggregates with an average diameter of 13 nm. Furthermore, the solubilization of an OPV homooligomer with the block copolymer was studied. When the total polymer concentration was less than 0.1 wt %, the block copolymer solubilized OPV with a 50 mol % concentration. The structure of the aggregates was a cylinder with a relatively large diameter distribution. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1569–1578, 2005     

One‐pot synthesis of conjugated poly(3‐hexylthiophene)‐b‐poly(phenyl isocyanide) hybrid rod–rod block copolymers and its self‐assembling properties

In this article, the synthesis of a series of conjugated rod–rod block copolymers based on poly(3‐hexylthiophene) (P3HT) and poly(phenyl isocyanide) (PPI) building blocks in a single pot is presented. Ni‐catalyzed Grignard metathesis polymerization of 2,5‐dibromo‐3‐hexylthiophene and subsequent addition of 4‐isocyanobenzoyl‐2‐aminoisobutyric acid decyl ester in the presence of Ni(dppp)Cl₂ as a single catalyst afford P3HT‐b‐PPI with tunable molecular weights and compositions. In solid state, microphase separation occurred as differential scanning calorimetric analysis of P3HT‐b‐PPI revealed two glass transition temperatures. In solutions, the copolymers can self‐assemble into spherical aggregates with P3HT core and PPI shell in tetrahydrofuran and exhibit amorphous state in CHCl₃. However, atomic force microscopy revealed that the block copolymers self‐assemble into nanofibrils on the substrate. These unique features warrant the resultant conjugated rod–rod copolymers' potential study in organic photovoltaic and other electronic devices. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2939–2947     

Evidence for the Chain‐Growth Synthesis of Statistical π‐Conjugated Donor–Acceptor Copolymers

The synthesis of a series of dithienosilole–benzotriazole donor–acceptor statistical copolymers with various donor–acceptor ratios is reported, prepared by Kumada catalyst‐transfer polymerization. Statistical copolymer structure is verified by ¹H NMR and optical absorption spectroscopy, and supported by density functional theory (DFT) calculations. The copolymers exhibit a single optical absorption band that lies between dithienosilole and benzotriazole homopolymers, which shifts with varying donor–acceptor content. A chain extension experiment using a partially consumed benzotriazole solution as a macroinitiator followed by addition of dithienosilole leads to the synthesis of a statistical dithienosilole–benzotriazole block copolymer from a pure benzotriazole block, demonstrating that both chain extension and simultaneous monomer incorporation are possible using this methodology.

     

Synthesis and characterization of poly(1,4‐bis((E)‐2‐(3‐dodecylthiophen‐2‐yl)vinyl)benzene) derivatives

New amorphous semiconducting copolymers, poly(9,9‐dialkylfluorene)‐alt‐(3‐dodecylthienyl‐divinylbenzene‐3‐dodecylthienyl) derivatives (PEFTVB and POFTVB), were designed, synthesized, and characterized. The structure of copolymers was confirmed by H NMR, IR, and elemental analysis. The copolymers showed very good solubility in organic solvents and high thermal stability with high T_g of 178–185 °C. The weight average molecular weight was found to be 107,900 with polydispersity of 3.14 for PEFTVB and 76,700 with that of 3.31 for POFTVB. UV–vis absorption studies showed the maximum absorption at 428 nm (in solution) and 435 nm (in film) for PEFTVB and at 430 nm (in solution) and 436 nm (in film) for POFTVB. Photoluminescence studies showed the emission at 498 nm (in solution) and 557 nm (in film) for PEFTVB and at 498 nm (in solution) and 536 nm (in film) for POFTVB. The solution‐processed thin‐film transistors showed the carrier mobility of 2 × 10^?4 cm² V^?1 s^?1 for PEFTVB‐based devices and 2 × 10^?5 cm² V^?1 s^?1 for POFTVB‐based devices. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3942–3949, 2010     

Microwave‐assisted synthesis of star‐shaped poly(ε‐caprolactone)‐block‐poly(L‐lactide) copolymers and the crystalline morphologies

A monomode microwave reactor was used for the synthesis of designed star‐shaped polymers, which were based on dipentaerythritol with six crystallizable arms of poly(ε‐caprolactone)‐b‐poly(L ‐lactide) (PCL‐b‐PLLA) copolymer via a two‐step ring‐opening polymerization (ROP). The effects of irradiation conditions on the molecular weight were studied. Microwave heating accelerated the ROP of CL and LLA, compared with the conventional heating method. The resultant hexa‐armed polymers were fully characterized by means of FTIR, ¹H NMR spectrum, and GPC. The investigation of thermal properties and crystalline behaviors indicated that the crystalline behaviors of polymers were largely depended on the macromolecular architecture and the length of the block chains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Phase separation and polymer crystallization in a poly(4‐methyl‐1‐pentene)–dioctylsebacate–dimethylphthalate system via thermally induced phase separation

The effects of the polymer concentration and quenching temperature on the phase separation, the membrane morphology and polymer crystallization behavior in a poly(4‐methyl‐1‐pentene) (TPX)‐dioctylsebacate (DOS)‐dimethylphthalate (DMP) system via thermally induced phase separation were studied with a pseudobinary phase diagram, with the weight ratio of DOS:DMP = 1:1. SEM was used to observe the membrane morphology and structure, whereas the TPX crystallization behavior was studied with DSC and WAXD. Liquid‐liquid phase separation occurred, although quenching under the crystallization temperature. As the quenching temperature decreased, the pore size decreased, with better connected pore structure formed. The membranes quenched at 333 and 363 K showed good cellular structures, with an average pore size of about 2.3μm, whereas the pores of the membranes quenched at 393 and 423 K were not well formed, with some lamellar crystals on the inner side. The diluent assisted the mobility of the polymer chain, which improved the polymer crystallization. Dual‐melting‐peak behavior occurred for all the samples studied here. As the quenching temperature increased, the first peak of the melting trace moved to a higher temperature, whereas the second one stayed almost the same. The flexibility of the TPX main chain was restricted by the side groups, which allowed liquid‐liquid phase separation to occur first when quenched below the equilibrium crystallization temperature. This allowed primary and secondary crystallization, which was responsible for the dual‐melting‐peak behavior. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 153–161, 2007     

Synthesis of poly(p‐phenylene)‐poly(4‐diphenylaminostyrene) bipolar block copolymers with a well‐controlled and defined polymer chain structure

A poly(p‐phenylene) (PPP)‐poly(4‐diphenylaminostyrene) (PDAS) bipolar block copolymer was synthesized for the first time. A prerequisite prepolymer, poly(1,3‐cyclohexadiene) (PCHD)‐PDAS binary block copolymer, in which the PCHD block consisted solely of 1,4‐cyclohexadiene (1,4‐CHD) units, was synthesized by living anionic block copolymerization of 1,3‐cyclohexadiene and 4‐diphenylaminostyrene. To obtain the PPP‐PDAS bipolar block copolymer, the dehydrogenation of this prepolymer with quinones was examined, and tetrachloro‐1,2‐(o)‐benzoquinone was found to be an appropriate dehydrogenation reagent. This dehydrogenation reaction was remarkably accelerated by ultrasonic irradiation, effectively yielding the target PPP‐PDAS bipolar block copolymer. The hole and electron drift mobilities for PPP‐PDAS bipolar block copolymer were both on the order of 10^?3 to 10^?4 cm²/V·s, with a negative slope when plotted against the square root of the applied field. Therefore, this bipolar block copolymer was found to act as a bipolar semi‐conducting copolymer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis,one‐ and two‐photon properties of poly[9,10‐bis(3,4‐bis(2‐ethylhexyl‐oxy)phenyl)‐2,6‐anthracenevinylene‐alt‐N‐octyl‐3,6‐/2,7‐carbazolevinylene]

The synthesis, one‐ and two‐photon absorption (TPA) and emission properties of two novel 2,6‐anthracenevinylene‐based copolymers, poly[9,10‐bis(3,4‐bis(2‐ethylhexyloxy)phenyl)‐2,6‐anthracenevinylene‐alt‐N‐octyl‐3,6‐carbazolevinyl‐ene] ( P1 ) and poly[9,10‐bis(3,4‐bis(2‐ethylhexyloxy)phenyl)‐2,6‐anthracenevinyl‐ene‐alt‐N‐octyl‐2,7‐carbazolevinylene] ( P2 ) were reported. The as‐synthesized polymers have the number‐average molecular weights of 1.56 × 10⁴ for P1 and 1.85 × 10⁴ g mol^?1 for P2 and are readily soluble in common organic solvents. They emit strong bluish‐green one‐ and two‐photon excitation fluorescence in dilute toluene solution (? _P1 = 0.85, ? _P2 = 0.78, λ_em( P1 ) = 491 nm, λ_em( P2 ) = 483 nm). The maximal TPA cross‐sections of P1 and P2 measured by the two‐photon‐induced fluorescence method using femtosecond laser pulses in toluene are 840 and 490 GM per repeating unit, respectively, which are obviously larger than that (210 GM) of poly[9,10‐bis‐(3,4‐bis(2‐ethylhexyloxy) phenyl)‐2,6‐anthracenevinylene], indicating that the poly(2,6‐anthracenevinylene) derivatives with large TPA cross‐sections can be obtained by inserting electron‐donating moieties into the polymer backbone. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 463–470, 2010     

Synthesis of block copolymers comprised of poly(3‐hexylthiophene) segment with trisiloxane side chains and their application to organic thin film transistor

The demand of stretchability for a semiconducting polymer has increased to realize wearable devices and sensors. However, studies involving intrinsically stretchable π‐conjugated polymers are still limited. Here, we develop a soft‐polythiophene derivative, P3SiHT, with a trisiloxane unit in the side chains via a hexylene spacer unit. In addition, diblock (P3HT‐b‐P3SiHT) and triblock (P3HT‐b‐P3SiHT‐b‐P3HT) copolymers could be synthesized based on Kumada catalyst‐transfer polycondensation. The results of atomic force microscopy and grazing incidence small‐angle X‐ray scattering indicate that the block copolymer thin films form a phase‐separated structure between the P3HT and P3SiHT domains. The organic thin film transistor devices were prepared to assess the electrical properties of the block polymers. As a result, the block copolymers showed comparable or even higher hole mobility than that of P3HT homopolymer, thus due to the enhanced phase‐separation and thereby charge transportation. The mechanical test of the bulk films indicates that P3HT‐b‐P3SiHT‐b‐P3HT shows lower tensile modulus and longer elongation at break than P3HT homopolymer and other diblock copolymers. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1787–1794     

Amphiphilic diblock copolymers based on poly(2‐ethyl‐2‐oxazoline) and poly(4‐substituted‐ε‐caprolactone): Synthesis,characterization, and cellular uptake

Amphiphilic diblock copolymers with various block compositions were synthesized on poly(2‐ethyl‐2‐oxazoline) (PEtOz) as a hydrophilic block and poly(4‐methyl‐ε‐caprolactone) (PMCL) or poly(4‐phenyl‐ε‐caprolactone) (PBCL) as a hydrophobic block. These PEtOz‐b‐PMCL and PEtOz‐b‐PBCL copolymers consisting of soft domains of amorphous PEtOz and PM(B)CL had no melting endothermal peaks but displayed T_g. The lower critical solution temperature (LCST) values for the PEtOz‐b‐PMCL, and the PEtOz‐b‐PBCL aqueous solution were observed to shift to lower temperature than PEtOz homopolymers. Their aqueous solutions were characterized using fluorescence techniques and dynamic light scattering (DLS). The block copolymers formed micelles with critical micelle concentrations (CMCs) in the range 0.6–11.1 mg L^?1 in an aqueous phase. As the length of the hydrophobic PMCL or PBCL blocks elongated, lower CMC values were generated. The mean diameters of the micelles were between 127 and 318 nm, with PDI in the range of 0.06–0.21, suggesting nearly monodisperse size distributions. The drug entrapment efficiency and drug‐loading content of micelles depend on block polymer compositions. In vitro cell viability assay showed that PEtOz‐b‐PMCL has low cytotoxicity. Doxorubicin hydrochloride (DOX)‐loaded micelles facilitated human cervical cancer (HeLa) cell uptake of DOX; uptake was completed within 2 h, and DOX was able to reach intracellular compartments and enter the nuclei by endocytosis. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2769–2781     

Insights into poly(3‐hexylthiophene)‐b‐poly(ethylene oxide) block copolymer: Synthesis and solvent‐induced structure formation in thin films

We report the synthesis, characterization, and solvent‐induced structure formation in thin films of an amphiphilic rod‐coil conjugated block copolymer, poly(3‐hexylthiophene)‐b‐poly(ethylene oxide). The diblock copolymers were prepared by a facile click reaction and their characterizations as well as thermal, crystalline, optical properties, and self‐assembly behavior have been investigated in detail. A series of morphologies including two‐phase separated nanostructure, nanofibrils, and their mixed morphology could be obtained depending on the selectivity of solvents to different blocks. Structural analyses demonstrate there is a subtle balance between microphase separation of copolymer and the π‐π stacking of the conjugated P3HT and such balance can be controlled by changing the solvents of different selectivity in solution and the length of P3HT block. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Melt crystallization and morphology of poly(ε‐caprolactone)‐poly(ethylene glycol) diblock copolymers with different compositions and molecular weights

Ring opening polymerization of ε‐caprolactone was realized in the presence of monomethoxy poly(ethylene glycol) with M_n = 1000 and 2000, using Zn(La)₂ as catalyst. The resulting PCL‐PEG diblock copolymers with CL/EO repeat unit molar ratios from 0.2 to 3.0 were characterized by using DSC, WAXD, SEC, and ¹H NMR. The crystal phase of PCL blocks exist in all polymers, and the crystallization ability of PCL blocks increases with CL/EO ratio. PEG blocks are able to crystallize for copolymers with CL/EO below 1.0 only. Melt crystallization results were analyzed with Avrami equation. The Averami exponent n is around 3.0 in most cases, in agreement with heterogeneous nucleation with three dimensional growth. The morphology of the crystals was observed by using POM. Rod‐like crystals were found to grow in 1, 3 or 2, 4 quadrants for samples with low molecular weights. In the case of a copolymer with M_n,PEG = 2000 and M_n,PCL = 800, PEG blocks could crystallize and grow on PCL crystals after PCL finished to form rod‐like crystals, leading to formation of poorly or well structured spherulites. The spherulite growth rate (G) was determined at different crystallization temperatures (T_c) ranging from 9 to 49 °C. All the copolymers present a steady G decrease with increasing crystallization temperature due to lower undercooling. On the other hand, increase of CL/EO ratio leads to increase of G in the same T_c range. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 286–293, 2010     

Synthesis and characterization of donor–acceptor poly(3‐hexylthiophene) copolymers presenting 1,3,4‐oxadiazole units and their application to photovoltaic cells

We have used Grignard metathesis polymerization to prepare poly(3‐hexylthiophene)‐based copolymers containing electron‐withdrawing 4‐tert‐butylphenyl‐1,3,4‐oxadiazole‐phenyl moieties as side chains. We characterized these copolymers using ¹H and ¹³C nuclear magnetic resonance spectroscopy, thermogravimetric analysis, and gel permeation chromatography. The band gap energy of copolymer was determined from the onset of the optical absorption. The quenching effects were observed in the photoluminescence spectra of the copolymers incorporating pendant electron‐deficient 1,3,4‐oxadiazole moieties on the side chains. The photocurrents of devices were enhanced in the presence of an optimal amount of the 1,3,4‐oxadiazole moieties, thereby leading to improved power conversion efficiencies. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3331–3339, 2010     

Synthesis,reactivity, and optoelectronic properties of poly(3‐alkenylthiophene) diblock copolymers

Poly(3‐hexylthiophene)‐b‐poly(3‐pentenylthiophene) and poly(3‐hexylthiophene)‐b‐poly(3‐undecenylthiophene) diblock copolymers have been synthesized by McCullough method. X‐ray diffraction analysis of the diblock copolymers displayed all the reflection peaks specific to regioregular poly(3‐hexylthiophene), indicating that the presence of poly(3‐alkenylthiophene) block does not affect the packing of the polymer in the solid state. The synthesized diblock copolymers were subjected to hydroboration/oxidation and hydrosilation to demonstrate the reactivity of the alkenyl substituents. Furthermore, poly(3‐hexylthiophene)‐b‐poly(3‐pentenylthiophene) was used as a chain transfer agent for the ruthenium‐catalyzed ring‐opening metathesis polymerization of cyclooctene to generate a polycyclooctene graft copolymer, which was hydrogenated to give poly(3‐hexylthiophene)‐b‐poly(3‐pentenylthiophene‐g‐polyethylene). The opto‐electronic properties and the morphology of the synthesized polymers have been investigated. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

α‐keto‐β‐diimine nickel‐catalyzed olefin polymerization: Effect of ortho‐aryl substituents and preparation of stereoblock copolymers

A series of α‐keto‐β‐diimine nickel complexes (Ar‐N = C(CH₃)‐C(O)‐C(CH₃)=N‐Ar)NiBr₂; Ar = 2,6‐R‐C₆H₃‐, R = Me, Et, iPr, and Ar = 2,4,6‐Me₃‐C₆H₃‐) was prepared. All corresponding ligands are unstable even under an inert atmosphere and in a freezer. Stable copper complex intermediates of ligand synthesis and ethyl substituted nickel complex were isolated and characterized by X‐ray. All nickel complexes were used for the polymerization of ethene, propylene, and hex‐1‐ene to investigate their livingness and the extent of chain‐walking. Low‐temperature propene polymerization with less bulky ortho‐substituents was less isospecific than the one with isopropyl derivative. Propene stereoblock copolymers were prepared by iPr derivative combining the polymerization at low temperature to prepare isotactic polypropylene (PP) block and at a higher temperature, supporting chain‐walking, to obtain amorphous regioirregular PP block. Alternatively, a copolymerization of propene with ethene was used for the preparation of amorphous block. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2440–2449