Synthesis and characterization of highly conjugated side‐group‐substituted benzo[1,2‐b:4,5‐b′]dithiophene‐based copolymer for use in organic solar cells

A new donor–acceptor (D–A) conjugated copolymer based on benzo[1,2‐b:4,5‐b′]dithiophene (BDT) and thieno[3,4‐c]pyrrole‐4,6‐dione (TPD) was synthesized via a Stille cross‐coupling reaction. A highly conjugated thiophene‐based side group, tris(thienylenevinylene) (TTV), was incorporated into each BDT unit to generate the two‐dimensional D–A copolymer (PBDT‐TTV). An alkoxy‐substituted BDT‐based TPD copolymer (PBDT‐OR) was synthesized using the same polymerization method for comparison. PBDT‐TTV thin films produced two distinct absorption peaks. The shorter wavelength absorption (458 nm) was attributed to the BDT units containing the TTV group, and the longer wavelength band (567–616 nm) was attributed to intramolecular charge transfer between the BDT donor and the TPD acceptor. The highest occupied molecular orbital energy levels of PBDT‐OR and PBDT‐TTV were calculated to be −5.53 and −5.61 eV, respectively. PBDT‐TTV thin films harvested a broad solar spectrum covering the range 300–700 nm. A comparison with the PBDT‐OR films revealed stronger interchain π–π interactions in the PBDT‐TTV films and, thus, a higher hole mobility. A polymer solar cell device prepared using PBDT‐TTV as the active layer was found to exhibit a higher power conversion efficiency than a device prepared using PBDT‐OR under AM 1.5 G (100 mW/cm²) conditions. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 653–660     

Benzo[2,1‐b;3,4‐b′]dithiophene‐based low‐bandgap polymers for photovoltaic applications

The synthesis of four alternating copolymers using benzo[2,1‐b;3,4‐b′]dithiophene (BDP) as the common donor unit is presented. Before the synthesis, theoretical calculations that we performed predicted that the incorporation of BDP, which consists of fused dithiophene units with a benzene ring, into these polymers would produce a low‐lying highest occupied molecular orbital (HOMO) energy level. Low‐lying HOMO levels are desirable to produce high open circuit voltages (V_OC) in organic bulk heterojunction (BHJ) photovoltaic devices. The polymers' structural characterization, as well as the preliminary results of their performance in BHJ devices, using (6,6)‐phenyl C₆₁‐butyric acid methyl ester as the electron acceptor, is presented. The V_OC values follow the expected trend: increasing with decreasing HOMO level of the polymer. High V_OC values of 0.81 and 0.82 V have been obtained from two polymers: PBDPBT and PBDPDPP. The initial power conversion efficiency achieved in these unoptimized devices was 1.11% because of relatively low J_SC values. The variation observed in the J_SC values between the four polymers is discussed. Device performance is expected to increase with optimization of processing conditions for the devices. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

New conjugated copolymers based on benzo[1,2‐b; 3,4‐b′]dithiophene and derivatives of benzo[g]quinoxaline for bulk heterojunction solar cells

A series of new low‐band gap copolymers based on dioctyloxybenzo[1,2‐b;3,4‐b′] dithiophene and bis(2‐thienyl)‐2,3‐diphenylbenzo[g]quinoxaline monomers have been synthesized via a Stille reaction. The effect of different functional groups attached to bis(2‐thienyl)‐2,3‐diphenylbenzo[g]quinoxaline was investigated and compared with their optical, electrochemical, hole mobility, and photovoltaic properties. Polymer solar cell (PSC) devices of the copolymers were fabricated with a configuration of ITO/ PEDOT: PSS/copolymers: PCBM (1:4 wt ratio)/Ca/Al. The best performance of the PSC device was obtained by using PbttpmobQ as the active layer. A power conversion efficiency of 1.42% with an open‐circuit voltage of 0.8 V, a short‐circuit current (JSC) of 5.73 mA cm⁻², and a fill factor of 30.9% was achieved under the illumination of AM 1.5, 100 mW cm⁻². © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and photovoltaic performance of donor–acceptor polymers containing benzo[1,2‐b:4,5‐b′]dithiophene with thienyl substituents

Three alternating donor–acceptor copolymers have been synthesized by Stille coupling polymerization of 2,6‐(trimethyltin)?4,8‐bis(5‐dodecylthiophene‐2‐yl)benzo[1,2‐b:4,5‐b′]dithiophene with 1,3‐dibromo‐5‐hexylthieno[3,4‐c]pyrrole‐4,6‐dione, 4,7‐dibromo‐1,3‐benzothiadiazole, and 5,7‐dibromo‐2,3‐didodecylthieno[3,4‐b]pyrazine, respectively. The synthesized polymers were tested in bulk heterojunction solar cells as blends with the acceptor [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM). The thienopyrroledione copolymer displayed a power conversion efficiency of 3.00% which was increased to 3.86% by application of the additive 1,8‐diiodooctane (DIO). Tapping mode atomic force microscopy analysis indicated that there was an increase in the phase separation between polymer and PCBM, leading to an improvement in the performance upon the addition of DIO. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2622–2630     

Synthesis and characterization of naphtho[2,1‐b:3,4‐b′]dithiophene‐based polymers with extended π‐conjugation systems for use in bulk heterojunction polymer solar cells

Two novel polymeric semiconductor materials based on naphtho[2,1‐b:3,4‐b']dithiophene (NDT), PNDT‐TTT and PNDT‐TET , were designed and synthesized. These synthesized polymers were tested in bulk heterojunction solar cells as blends with the acceptor [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₁BM). PNDT‐TTT contained tri‐thiophene units, and PNDT‐TET contained bi‐thiophene units coupled by ethylenic linkages. Comparison to the properties of PNDT‐T , which contained single thiophene units, these polymers exhibit red‐shifted absorption spectra as a result of the enhanced conjugation lengths. These effects resulted in high short circuit currents (J_SC) in the organic solar cells. The PNDT‐TET ‐ and PNDT‐TTT ‐based devices exhibited considerably better photovoltaic performances, with power conversion efficiencies of 3.5 and 3.3%, respectively, compared to the PNDT‐T ‐based device (1.3%). © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4742–4751     

4,9‐Dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione functionalized copolymers for organic photovoltaic devices

The synthesis of conjugated polymers 1 – 5 functionalized with 4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione in the backbone is reported and their use in the construction of organic solar cells is demonstrated. Increasing the molar ratio of 2,7‐dibromo‐3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione, relative to 4,4′‐dihexyl‐5,5′‐dibromo‐2,2′‐bithiophene, in the copolymer synthesis significantly lowers the solubility of these polymers. The incorporation of highly conjugated 3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione unit into the polymer backbone has been confirmed by UV–vis absorption. The observation of decreasing quantum yield for the emission in the order of 1 , 2 , 3 is consistent with copolymers with different comonomer content. The power conversion efficiencies of solar cells using blends of these polymers with PCBM ([6,6]‐phenyl C₆₁‐butyric acid methyl ester) were determined to be 0.11% for polymer 1 , 0.33% for 2 , and 0.26% for 3 , respectively. Under identical white light illumination, the power conversion efficiency of the device based on polymer 2 /PCBM as the active layer was three times higher compared to that of device based on polymer 1 /PCBM. Owing to the limited solubility and poor film‐forming ability of polymer 3 , the power conversion efficiency of solar cell based on 3 /PCBM blend is lower than that of 2 /PCBM blend, but is still larger than that of 1 /PCBM blend. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2680–2688, 2008     

Naphtho[2,1‐b:3,4‐b′]dithiophene‐based Bulk Heterojunction Solar Cells: How Molecular Structure Influences Nanoscale Morphology and Photovoltaic Properties

Organic bulk heterojunction photovoltaic devices based on a series of three naphtho[2,1‐b:3,4‐b′]dithiophene (NDT) derivatives blended with phenyl‐C₇₁‐butyric acid methyl ester were studied. These three derivatives, which have NDT units with various thiophene‐chain lengths, were employed as the donor polymers. The influence of their molecular structures on the correlation between their solar‐cell performances and their degree of crystallization was assessed. The grazing‐incidence angle X‐ray diffraction and atomic force microscopy results showed that the three derivatives exhibit three distinct nanoscale morphologies. We correlated these morphologies with the device physics by determining the J–V characteristics and the hole and electron mobilities of the devices. On the basis of our results, we propose new rules for the design of future generations of NDT‐based polymers for use in bulk heterojunction solar cells.     

Alternating copolymers incorporating cyclopenta[2,1‐b:3,4‐b′]dithiophene unit and organic dyes for photovoltaic applications

We have synthesized six p‐type copolymers, CPDT ‐ co ‐ TPADCN , CPDT ‐ co ‐ TPADTA , CPDT ‐ co ‐ TPATCN , CPDT ‐ co ‐ DFADCN , CPDT ‐ co ‐ DFADTA , and CPDT ‐ co ‐ DFATCN , consisting of a cyclopenta[2,1‐b:3,4‐b′]dithiophene (CPDT) unit and an organic dye in an alternating arrangement. Triphenylamine (TPA) or difluorenylphenyl amine (DFA) units serve as the electron donors, whereas dicyanovinyl (DCN), 1,3‐diethyl‐2‐thiobarbituric acid, or tricyanovinyl (TCN) units act as the electron acceptors in the dyes. The target polymers were prepared via Stille coupling, followed by postfunctionalization to introduce the electron acceptors to the side chains. Because of the strongest withdrawing ability of TCN acceptor to induce efficient intramolecular charge transfer, CPDT ‐ co ‐ TPATCN and CPDT ‐ co ‐ DFATCN exhibit the broader absorption spectra covering from 400 to 900 nm and the narrower optical band gaps of 1.34 eV. However, the CPDT ‐ co ‐ TPATCN :PC₇₁BM and CPDT ‐ co ‐ DFATCN :PC₇₁BM based solar cells showed the power conversion efficiencies (PCEs) of 0.22 and 0.31%, respectively, due to the inefficient exciton dissociation. The DFA‐based polymers possess deeper‐lying HOMO energy levels than the TPA‐based polymer analogues, leading to the higher V_oc values and better efficiencies. The device based on CPDT ‐ co ‐ DFADTA :PC₇₁BM blend achieved the best PCE of 1.38% with a V_oc of 0.7 V, a J_sc of 4.57 mA/cm², and a fill factor of 0.43. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Using Cyclopenta[2,1‐b:3,4‐c′]dithiophene‐4‐one as a Building Block for Low‐Bandgap Conjugated Copolymers Applied in Solar Cells

A novel electron‐accepting unit cyclopenta[2,1‐b:3,4‐c′]dithiophene‐4‐one (CPDTO‐c′), which is an isomer of CPDTO‐b′ was developed. CPDTO‐c′ can be incorporated into the D–A backbone through 5, 7 positions. The 2 position of CPDTO‐c′ can be easily functionalized with an electron‐withdrawing chain. By copolymerizing CPDTO‐c′ with four different donor units: benzo[1,2‐b:4,5‐b′]dithiophene (BDT), dithieno[3,2‐b:2′,3′‐d]silole (DTS), carbazole, and fluorene, four new conjugated copolymers P1 – P4 were obtained. All these polymers have good solubility and low‐lying HOMO energy levels (−5.41 ∼ −5.92 eV). Among them, P1 and P2 exhibit broad absorption and narrow optical bandgaps of 1.91 and 1.72 eV, respectively. Solar cells based on P1 /PC₇₁BM afforded a PCE up to 2.72% and a high V_oc up to ∼0.9 V.     

Poly(4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene vinylene): Synthesis,optical and photovoltaic properties

A new benzodithiophene (BDT)‐based polymer, poly(4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene vinylene) (PBDTV), was synthesized by Pd‐catalyzed Stille‐coupling method. The polymer is soluble in common organic solvents and possesses high thermal stability. PBDTV film shows a broad absorption band covering from 350 nm to 618 nm, strong photoluminescence peaked at 545 nm and high hole mobility of 4.84 × 10^?3 cm²/Vs. Photovoltaic properties of PBDTV were studied by fabricating the polymer solar cells based on PBDTV as donor and PC₇₀BM as acceptor. With the weight ratio of PBDTV: PC₇₀BM of 1:4 and the active layer thickness of 65 nm, the power conversion efficiency of the device reached 2.63% with V_oc = 0.71 V, I_sc = 6.46 mA/cm², and FF = 0.57 under the illumination of AM1.5, 100 mW/cm². © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1822–1829, 2010     

A vinylene‐linked benzo[1,2‐b:4,5‐b']dithiophene‐2,1,3‐benzothiadiazole low‐bandgap polymer

A new heteroarylene‐vinylene donor–acceptor polymer P(BDT‐V‐BTD) with reduced bandgap has been synthesized and its photophysical, electronic and photovoltaic properties investigated both experimentally and theoretically. The structure of the polymer comprises an unprecedented combination of a strong donor (4,8‐dialkoxy‐benzo[1,2‐b:4,5‐b']dithiophene, BDT), a strong acceptor (2,1,3‐benzothiadiazole, BTD) and a vinylene spacer. The new polymer was obtained by a metal‐catalyzed cross‐coupling Stille reaction and fully characterized by NMR, UV–vis absorption, GPC, TGA, DSC and electrochemistry. Detailed ab initio computations with solvation effects have been performed for the monomer and model oligomers. The electrochemical investigation has ascertained the ambipolar character of the polymer and energetic values of HOMO, LUMO and bandgap matching materials‐design rules for optimized organic photovoltaic devices. The HOMO and LUMO energies are consistently lower than those of previous heteroarylene‐vinylene polymer while the introduction of the vinylene spacer afforded lower bandgaps compared to the analogous system P(BDT‐BTD) with no spacer between the aromatic rings. These superior properties should allow for enhanced photovoltages and photocurrents in photovoltaic devices in combination with PCBM. Preliminary photovoltaic investigation afforded relatively modest power conversion efficiencies of 0.74% (AM 1.5G, 100 mW/cm²), albeit higher than that of previous heteroarylene‐vinylene polymers and comparable to that of P(BDT‐BTD). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Reduced‐bandgap triphenylamine‐alt‐benzo[1,2‐b:4,5‐b′]dithiophene copolymers pending benzothiadiazole or diketopyrrolopyrrole units for efficient polymer solar cells

Two new side‐chain donor–acceptor (D‐A)‐based triphenylamine‐alt‐benzo[1,2‐b:4,5‐b′]dithiophene (TPA‐alt‐BDT) copolymers ( P1 and P2 ) with pendant benzothiadiazole (BT)/diketopyrrolopyrrole (DPP) in TPA unit were synthesized by Stille coupling polymerization. Their thermal, photophysical, electrochemical, blend film morphology and photovoltaic properties were investigated. Efficient bulk heterojunction polymer solar cells (PSCs) were obtained by solution process using both copolymers as donor materials and PC₇₁BM as acceptor. The maximum power conversion efficiency (PCE) of 3.17% with a highest open‐circuit voltage (V_oc) of 0.86V was observed in the P1 ‐based PSCs, while the maximum short‐circuit current (J_sc) of 10.77 mA cm^?2 was exhibited in the P2 ‐based PSCs under the illumination of AM 1.5, 100 mW cm^?2. The alternating binary donor units and pending acceptor groups played a significant role in tuning photovoltaic properties for this class of the side‐chain D–A‐based copolymers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4103–4110     

Synthesis and photovoltaic properties of copolymers based on benzo[1,2‐b:4,5‐b′]dithiophene and thiophene with electron‐withdrawing side chains

Six alternating conjugated copolymers ( PL1 – PL6 ) of benzo[1,2‐b:4,5‐b′]dithiophene (BDT) and thiophene, containing electron‐withdrawing oxadiazole (OXD), ester, or alkyl as side chains, were synthesized by Stille coupling reaction. The structures of the polymers were confirmed, and their thermal, optical, electrochemical, and photovoltaic properties were investigated. The introduction of conjugated electron‐withdrawing OXD or formate ester side chain benefits to decrease the bandgaps of the polymers and improve the photovoltaic performance due to the low steric hindrance of BDT. Bulk heterojunction polymer solar cells (PSCs) were fabricated based on the blend of the as‐synthesized polymers and the fullerene derivative [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) in a 1:2 weight ratio. The maximum power conversion efficiency of 2.06% was obtained for PL5 ‐based PSC under the illumination of AM 1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and photovoltaic properties of thieno[3,4‐b]pyrazine or dithieno[3′,2′:3,4;2″,3″:5,6]benzo[1,2‐d]imidazole‐containing conjugated polymers

Novel conjugated polymers composed of benzo[1,2‐b:4,5‐b′]dithiophene and thieno[3,4‐b]pyrazine or dithieno[3′,2′:3,4;2″,3″:5,6]benzo[1,2‐d]imidazole units are synthesized by Stille polycondensation. The resulting polymers display a longer wavelength absorption and well‐defined redox activities. The effective intramolecular charge‐transfer and energy levels of all polymers are elucidated by computational calculations. Bulk‐heterojunction solar cells based on these polymers as p‐type semiconductors and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) as an n‐type semiconductor are fabricated, and their photovoltaic performances are for the first time evaluated. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1067–1075     

New moderate bandgap polymers containing alkoxysubstituted‐benzo[c][1,2,5]thiadiazole and thiophene‐based units

Alkoxysubstituted benzo[c][1,2,5]thiadiazole electron accepting units were prepared and copolymerized with various thiophene‐based electron donating monomers to produce new low bandgap polymers P1–4 . The materials showed broad absorption in the range from 300 to 700 nm with bandgaps below 2 eV in solution. Efficiencies of over 1% were obtained from photovoltaic cells using P4 with PCBM as acceptor. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Modulation of electronic properties of π‐conjugated copolymers derived from naphtho[1,2‐b:5,6‐b′]dithiophene donor unit: A structure‐property relationship study

A set of three donor‐acceptor conjugated (D‐A) copolymers were designed and synthesized via Stille cross‐coupling reactions with the aim of modulating the optical and electronic properties of a newly emerged naphtho[1,2‐b:5,6‐b′]dithiophene donor unit for polymer solar cell (PSCs) applications. The PTNDTT‐BT , PTNDTT‐BTz , and PTNDTT‐DPP polymers incorporated naphtho[1,2‐b:5,6‐b′]dithiophene ( NDT ) as the donor and 2,2′‐bithiazole ( BTz ), benzo[1,2,5]thiadiazole ( BT ), and pyrrolo[3,4‐c]pyrrole‐1,4(2H,5H)‐dione ( DPP ), as the acceptor units. A number of experimental techniques such as differential scanning calorimetry, thermogravimetry, UV–vis absorption spectroscopy, cyclic voltammetry, X‐ray diffraction, and atomic force microscopy were used to determine the thermal, optical, electrochemical, and morphological properties of the copolymers. By introducing acceptors of varying electron withdrawing strengths, the optical band gaps of these copolymers were effectively tuned between 1.58 and 1.9 eV and their HOMO and LUMO energy levels were varied between ?5.14 to ?5.26 eV and ?3.13 to ?3.5 eV, respectively. The spin‐coated polymer thin film exhibited p‐channel field‐effect transistor properties with hole mobilities of 2.73 × 10^?3 to 7.9 × 10^?5 cm² V^?1 s^?1. Initial bulk‐heterojunction PSCs fabricated using the copolymers as electron donor materials and [6,6]‐phenyl C71 butyric acid methyl ester (PC₇₁BM) as the acceptor resulted in power conversion efficiencies in the range of 0.67–1.67%. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2948–2958     

Design and synthesis of dithieno[3,2‐b:2′3′‐d]pyrrole‐based conjugated polymers for photovoltaic applications: consensus between low bandgap and low HOMO energy level

A strategy of the fine‐tuning of the degree of intrachain charge transfer and aromaticity of polymer backbone was adopted to design and synthesize new polymers applicable in photovoltaics. Three conjugated polymers P1 , P2 , and P3 were synthesized by alternating the electron‐donating dithieno[3,2‐b:2′3′‐d]pyrrole (D) and three different electron‐accepting (A) segments ( P1 : N‐(2‐ethylhexyl)phthalimide; P2 : 1,4‐diketo‐3,6‐diphenylpyrrolo[3,4‐c]pyrrole; and P3 : thiophene‐3‐hexyl formate) in the polymer main chain. Among the three polymers, P2 possessed the broadest absorption band ranging from 300 to 760 nm, the lowest bandgap (1.63 eV), and enough low HOMO energy level (?5.27 eV) because of the strong intrachain charge transfer from D to A units and the appropriate extent of quinoid state in the main chain of P2 , which was convinced by the theoretical simulation of molecular geometry and front orbits. Photovoltaic study of solar cells based on the blends of P1 – P3 and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) demonstrated that P2 :PCBM exhibited the best performance: a power conversion efficiency of 1.22% with a high open‐circuit voltage (V_OC) of 0.70 V and a large short‐circuit current (I_SC) of 5.02 mA/cm² were achieved. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Benzo[1,2‐b:4,5‐b′]dithiophene Building Block for the Synthesis of Semiconducting Polymers

This review covers the synthesis and polymerization of benzo[1,2‐b: 4,5‐b′]dithiophene (BDT) to generate semiconducting polymers used in organic field‐effect transistors (OFET) and organic solar cells applications.     

A Soluble High Molecular Weight Copolymer of Benzo[1,2‐b:4,5‐b′]dithiophene and Benzoxadiazole for Efficient Organic Photovoltaics

The synthesis and characterization of a soluble high molecular weight copolymer based on 4,8‐bis(1‐pentylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene and 2,1,3‐benzoxadiazole is presented. High efficiency organic photovoltaic (OPV) devices comprised of this polymer and phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) were fabricated by additive processing with 1‐chloronapthalene (CN). When the active layer is cast from pristine chlorobenzene (CB), power conversion efficiencies (PCEs) average 1.41%. Our best condition—using 2% chloronapthalene as a solvent additive in CB—results in an average PCE of 5.65%, with a champion efficiency of 6.05%.