Ultrasensitive Detection of Cu<Superscript>2+</Superscript> Using a Microcantilever Sensor Modified with L-Cysteine Self-Assembled Monolayer

A microcantilever was modified with a self-assembled monolayer (SAM) of L-cysteine for the sensitively and selectively response to Cu(II) ions in aqueous solution. The microcantilever undergoes bending due to sorption of Cu(II) ions. The interaction of Cu(II) ions with the L-cysteine on the cantilever is diffusion controlled and does not follow a simple Langmuir adsorption model. A concentration of 10^?10 M Cu(II) was detected in a fluid cell using this technology. Other cations, such as Ni²⁺, Zn²⁺, Pb²⁺, Cd²⁺, Ca²⁺, K⁺, and Na⁺, did not respond with a significant deflection, indicating that this L-cysteine-modified cantilever responded selectively and sensitively to Cu(II).     

Highly sensitive and selective detection of beryllium ions using a microcantilever modified with benzo-9-crown-3 doped hydrogel

A microcantilever sensor modified by chitosan/gelatin hydrogels that are doped with benzo-9-crown-3 has been developed for the sensitive and selective detection of beryllium ions in an aqueous solution. The microcantilever undergoes bending deflection upon exposure to Be(2+) due to selective absorption of Be(2+) in the hydrogel. The detection limit is 10(-11) M. Other metal ions, such as Li(+), Na(+), K(+), Mg(2+), and Ca(2+), have a marginal effect on the deflection of the microcantilever. The mechanism of the bending is discussed and the results showed that the microcantilever may be used for in situ detection of beryllium.     

Control of 1D wave versus 2D honeycomb CoIIICdIICuI heterotrimetallic architectures by Delta L-Lambda L diastereoisomerism of L-cysteinatocobalt(III) building units

The reactions of the Delta L and Lambda L isomers of [Co( l-Hcys- N, S)(en) 2] (2+) ( l-H 2cys = l-cysteine) with CuCl in aqueous HCl gave Co (III)Cu (I) dinuclear complexes with the same S-bridged structures, Delta L- 1 and Lambda L- 1. When Delta L- 1 was treated with CdCl 2 in water, a 1D wavelike (Co (III) 2Cd (II)Cu (I)) n polymeric complex ( 2) was produced. On the other hand, similar treatment of Lambda L- 1 led to the formation of a 2D honeycomb-like (Co (III) 3Cd (II) 3Cu (I)) n polymeric complex ( 3), supported by the presence of counter-monoanions.     

Characterization of l-cysteine capped CdTe quantum dots and application to test Cu(II) deficiency in biological samples from critically ill patients

The catalytic activity of copper ion gives, from the physiological point of view, a central role in many biological processes. Variations in the composition and location of cellular copper have been addressed given their physiological and pathological consequences. In this paper l-cysteine capped CdTe quantum dots is used for the fluorimetric determination of Cu(II) in biological samples from healthy individuals and patients admitted to the Intensive Care Units (ICU). An acceptable homogeneity in the CdTe QDs size has been obtained with an average value of 3 nm. No significant alterations in the spectral properties were observed for 2 months when stored in vacutainers at 6 °C and a concentration of approximately 2 μM. Data from oxidative stress markers such superoxide dismutase, total antioxidant capacity and DNA damage can be correlated with a Cu(II) deficiency for the ICU patients as measured by flame-atomic absorption spectroscopy (FAAS) and inductively coupled plasma source mass spectrometry (ICP-MS). Aqueous solutions 0.3 μM of l-cysteine capped CdTe QDs in MOPS buffer (6 mM, pH 7.4) used at 21 °C in the range 15–60 min after preparation of the sample for the measurements of fluorescence gives contents in Cu(II) for erythrocytes in good agreement with those obtained in FAAS and ICP-MS but the comparative ease of use makes the fluorimetric technique more suitable than the other two techniques for routine analysis.     

Vapour phase Fourier transform infrared spectrometric determination of L-cysteine and L-cystine

A novel and selective procedure for the determination of l-cysteine and l-cystine based on vapour-generation Fourier transform infrared spectrometry is described. Potassium iodate solution was injected into a glass vessel containing l-cysteine and/or l-cystine. The evolved CO was swept by a stream of nitrogen to an infrared gas cell. The vapour phase FTIR spectra were continuously recorded, as a function of time, between 2240 and 2000cm(-1), which includes the CO absorption band. The maximum absorbance at 2170cm(-1) was selected as a measurement criterion. The calibration curve was linear over the range 6-300mgL(-1). The method provided a limit of detection of 2mgL(-1) of l-cysteine, a throughput of 12samples h(-1) and an R.S.D. of 1.76% for five independent analyses of a 75mgL(-1)l-cysteine solution. For the measurement of l-cysteine and l-cystine separately, after measuring total concentration of l-cysteine and l-cystine, l-cysteine was masked with p-benzoquinone at a pH of 3 and individual l-cystine was determined. The amount of l-cysteine was obtained by difference. The method was applied to the determination of l-cysteine and l-cystine in pharmaceutical and urine samples. Results obtained for real samples compared well with those obtained by a reference spectrometric method.     

An anti E. coli O157:H7 antibody-immobilized microcantilever for the detection of Escherichia coli (E. coli).

A silicon microcantilever sensor was developed for the detection of Escherichia coli O157:H7. The microcantilever was modified by anti-E. coli O157:H7 antibodies on the silicon surface of the cantilever. When the aquaria E. coli O157:H7 positive sample is injected into the fluid cell where the microcantilever is held, the microcantilever bends upon the recognition of the E. coli O157:H7 antigen by the antibodies on the surface of the microcantilever. A negative control sample that does not contain E. coli O157:H7 antigen did not cause any bending of the microcantilever. The detection limit of the sensor was 1 x 10(6) cfu/mL when the assay time was < 2 h.     

Renewable sol-gel carbon ceramic electrodes modified with a Ru-complex for the amperometric detection of l-cysteine and glutathione

A renewable three-dimensional chemically modified carbon ceramic electrode containing Ru [(tpy)(bpy)Cl] PF₆ was constructed by sol-gel technique. It exhibits an excellent electro-catalytic activity for oxidation of l-cysteine and glutathione at pH range 2-8. Cyclic voltammetry was employed to characterize the electrochemical behavior of the chemically modified electrode. The electrocatalytic behavior is further exploited as a sensitive detection scheme for l-cysteine and glutathione by hydrodynamic amperometry. Optimum pH value for detection is 2 for both l-cysteine and glutathione. The catalytic rate constants for l-cysteine and glutathione were determined, which were about 2.1×10³ and 2.5×10³ M⁻¹ s⁻¹, respectively. Under the optimized condition the calibration curves are linear in the concentration range 5-685 and 5-700 μM for l-cysteine and glutathione determination, respectively. The detection limit (S/N=3) and sensitivity is 1 μM, 5 nA/μM for l-cysteine and 1 μM, 7.8 nA/μM for glutathione. The relative standard deviation (RSD) for the amperogram's currents with five injections of l-cysteine or glutathione at concentration range of linear calibration is <1.5%. The advantages of this amperometric detector are: high sensitivity, good catalytic effect, short response time (t<3 s), remarkable long-term stability, simplicity of preparation and reproducibility of surface fouling (RSD for six successive polishing is 3.31%). This sensor can be used as a chromatographic detector for analysis of l-cysteine and glutathione.     

One-step synthesis and applications of fluorescent Cu nanoclusters stabilized by l-cysteine in aqueous solution

Herein, an innovative and simple strategy for synthesizing high fluorescent Cu nanoclusters was successfully established while l-cysteine played a role as the stabilizer. Meaningfully, the current Cu nanoclusters together with a quantum yield of 14.3% were prepared in aqueous solution, indicating their extensive applications. Subsequently, the possible fluorescence mechanism was elucidated by fluorescence, UV–vis, HR-TEM, FTIR, XPS, and MS. Additionally, the CuNCs were employed for assaying Hg²⁺ on the basis of the interactions between Hg²⁺ and l-cysteine; thus facilitating the quenching of their fluorescence. The proposed analytical strategy permitted detections of Hg²⁺ in a linear range of 1.0 × 10⁻⁷ mol L⁻¹ × 10⁻³ mol L⁻¹, with a detection limit of 2.4 × 10⁻⁸ mol L⁻¹ at a signal-to-noise ratio of 3. Significantly, this CuNCs described here were further applied for coding and fluorescent staining, suggesting may broaden avenues toward diverse applications.     

A novel potentiometric biosensor for selective L-cysteine determination using L-cysteine-desulfhydrase producing Trichosporon jirovecii yeast cells coupled with sulfide electrode

Trichosporon jirovecii yeast cells are used for the first time as a source of l-cysteine desulfhydrase enzyme (EC 4.4.1.1) and incorporated in a biosensor for determining l-cysteine. The cells are grown under cadmium stress conditions to increase the expression level of the enzyme. The intact cells are immobilized on the membrane of a solid-state Ag₂S electrode to provide a simple l-cysteine responsive biosensor. Upon immersion of the sensor in l-cysteine containing solutions, l-cysteine undergoes enzymatic hydrolysis into pyruvate, ammonia and sulfide ion. The rate of sulfide ion formation is potentiometrically measured as a function of l-cysteine concentration. Under optimized conditions (phosphate buffer pH 7, temperature 37 ± 1 °C and actual weight of immobilized yeast cells 100 mg), a linear relationship between l-cysteine concentration and the initial rate of sulfide liberation (dE/dt) is obtained. The sensor response covers the concentration range of 0.2-150 mg L⁻¹ (1.7-1250 μmol L⁻¹) l-cysteine. Validation of the assay method according to the quality control/quality assurance standards (precision, accuracy, between-day variability, within-day reproducibility, range of measurements and lower limit of detection) reveals remarkable performance characteristics of the proposed biosensor. The sensor is satisfactorily utilized for determination of l-cysteine in some pharmaceutical formulations. The lower limit of detection is ∼1 μmol L⁻¹ and the accuracy and precision of the method are 97.5% and ±1.1%, respectively. Structurally similar sulfur containing compounds such as glutathione, cystine, methionine, and d-cysteine do no interfere.     

Binding of glycine and L-cysteine on Si(111)-7 x 7

The adsorption of glycine and l-cysteine on Si(111)-7 x 7 was investigated using high-resolution electron energy loss spectroscopy (HREELS) and X-ray photoelectron spectroscopy (XPS). The observation of the characteristic vibrational modes and electronic structures of NH3+ and COO- groups for physisorbed glycine (l-cysteine) demonstrates the formation of zwitterionic species in multilayers. For chemisorbed molecules, the appearance of nu(Si-H), nu(Si-O), and nu(C=Omicron) and the absence of nu(O-H) clearly indicate that glycine and l-cysteine dissociate to produce monodentate carboxylate adducts on Si(111)-7 x 7. XPS results further verified the coexistence of two chemisorption states for each amino acid, corresponding to a Si-NH-CH2-COO-Si [Si-NHCH(CH2SH)COO-Si] species with new sigma-linkages of Si-N and Si-O, and a NH2-CH2-COO-Si [NH2CH(CH2SH)COO-Si] product through the cleavage of the O-H bond, respectively. Glycine/Si(111)-7 x 7 and l-cysteine/Si(111)-7 x 7 can be viewed as model systems for further modification of Si surfaces with biological molecules.     

Speciation of arsenic by hydride generation-atomic absorption spectrometry (HG-AAS) in hydrochloric acid reaction medium

The effects on the absorbance signals obtained using HG-AAS of variations in concentrations of the reaction medium (hydrochloric acid), the reducing agent [sodium tetrahydroborate(III); NaBH(4)], the pre-reducing agent (l-cysteine), and the contact time (between l-cysteine and arsenic-containing solutions) for the arsines generated from solutions of arsenite, arsenate, monomethylarsonic acid (MMA), and dimethylarsenic acid (DMA), have been investigated to find a method for analysis of the four arsenic species in environmental samples. Signals were found to be greatly enhanced in low acid concentration in both the absence (0.03-0.60 M HCl) and the presence of l-cysteine (0.001-0.03 M HCl), however with l-cysteine present, higher signals were obtained. Total arsenic content and speciation of DMA, As(III), MMA, and As(V) in mixtures containing the four arsenic species, as well as some environmental samples have been obtained using the following conditions: (i) total arsenic: 0.01 M acid, 2% NaBH(4), 5% l-cysteine, and contact time<10 min; (ii) DMA: 1.0 M acid, 0.3-0.6% NaBH(4), 4.0% l-cysteine, and contact time <5 min; (iii) As(III): 4-6 M acid and 0.05% NaBH(4) in the absence of l-cysteine; (iv) MMA: 4.0 M acid, 0.03% NaBH(4), 0.4% l-cysteine, and contact time of 30 min; (v) As(V): by difference. Detection limits (ppb) for analysis of total arsenic, DMA, As(III), and MMA were found to be 1.1 (n=7), 0.5 (n=5), 0.6 (n=7), and 1.8 (n=4), respectively. Good percentage recoveries (102-114%) of added spikes were obtained for all analyses.     

Label-free Microcantilever Immunosensor Based on a Competitive Immunoassay for the Determination of Clenbuterol

A label-free microcantilever immunosensor based on a competitive immunoassay is reported for the determination of clenbuterol. The immunosensor was fabricated by modifying clenbuterol–ovalbumin on the gold surface of the microcantilever with crossing linkage by L-cysteine and glutaraldehyde. Atomic force microscopy was utilized to characterize the construction of immunosensor and to measure the deflection of the microcantilever. The deflection response of the microcantilever was in negatively proportional to the concentration of clenbuterol from 1.0?×?10^?2 to 20?µg/L with a limit of detection of 1.0?×?10^?2?µg/L. The fabricated immunosensor was used to determine clenbuterol in pork samples with satisfactory results. In addition, the results were in accordance with those obtained by high-performance liquid chromatography. The reported immunosensor displayed high sensitivity and specificity together with excellent repeatability and reliability.     

A general microcantilever surface modification method using a multilayer for biospecific recognition

The key to microcantilever surface modification technology is to selectively modify one side of a microcantilever surface with molecular recognition layers. In this paper, we report a general microcantilever modification method using a multilayer film.     

Dimethyl methylphosphonate decomposition on Cu surfaces: supported Cu nanoclusters and films on TiO2(110)

The thermal decomposition of dimethyl methylphosphonate (DMMP), which is a simulant molecule for organophosphorus nerve agents, has been investigated on Cu clusters as well as on Cu films deposited on a TiO(2)(110) surface. Scanning tunneling microscopy studies were conducted to characterize the cluster sizes and surface morphologies of the deposited Cu clusters and films. Temperature-programmed desorption experiments demonstrated that the surface chemistry of DMMP is not sensitive to the size of the Cu clusters over the range studied in this work. DMMP reaction on an annealed 40 monolayer Cu film resulted in the desorption of H(2), methane, methyl, formaldehyde, methanol, and molecular DMMP, and reaction on the small (4.4 +/- 0.9 nm diameter, 1.8 +/- 0.6 nm height) and large (10.7 +/- 1.9 nm diameter, 4.8 +/- 1.0 nm height) Cu clusters generated similar products. Formaldehyde and methane production is believed to occur via a methoxy intermediate on the Cu surface. These products are favored on the higher coverage Cu films that completely cover the TiO(2) surface since competing reaction pathways on TiO(2) are suppressed. X-ray photoelectron spectroscopy studies showed that DMMP begins to decompose on the Cu clusters upon adsorption at room temperature and that atomic carbon, atomic phosphorus, and PO(x) remain on the surface after DMMP decomposition.     

Structural characterization and formation kinetics of sitting-atop (SAT) complexes of some porphyrins with copper(II) ion in aqueous acetonitrile relevant to porphyrin metalation mechanism. Structures of aquacopper(II) and cu(II)-SAT complexes as determined by XAFS spectroscopy

The formation of the sitting-atop (SAT) complexes of 5,10,15,20-tetraphenylporphyrin (H(2)tpp), 5,10,15,20-tetrakis(4-chlorophenyl)porphyrin (H(2)t(4-Clp)p), 5,10,15,20-tetramesitylporphyrin (H(2)tmp), and 2,3,7,8,12,13,17,18-octaethylporphyrin (H(2)oep) with the Cu(II) ion was spectrophotometrically confirmed in aqueous acetonitrile (AN), and the formation rates were determined as a function of the water concentration (C(W)). The decrease in the conditional first-order rate constants with the increasing C(W) was reproduced by taking into consideration the contribution of [Cu(H(2)O)(an)(5)](2+) in addition to [Cu(an)(6)](2+) to form the Cu(II)-SAT complexes. The second-order rate constants for the reaction of [Cu(an)(6)](2+) and [Cu(H(2)O)(an)(5)](2+) at 298 K were respectively determined as follows: (4.1 +/- 0.2) x 10(5) and (3.6 +/- 0.2) x 10(4) M(-1) s(-1) for H(2)tpp, (1.15 +/- 0.06) x 10(5) M(-1) s(-1) and negligible for H(2)t(4-Clp)p, and (4.8 +/- 0.3) x 10(3) and (1.3 +/- 0.3) x 10(2) M(-1) s(-1) for H(2)tmp. Since the reaction of H(2)oep was too fast to observe the reaction trace due to the dead time of 2 ms for the present stopped-flow technique, the rate constant was estimated to be greater than 1.5 x 10(6) M(-1) s(-1). According to the structure of the Cu(II)-SAT complexes determined by the fluorescent XAFS measurements, two pyrrolenine nitrogens of the meso-substituted porphyrins (H(2)tpp and H(2)tmp) bind to the Cu(II) ion with a Cu-N(pyr) distance of ca. 2.04 A, while those of the beta-pyrrole-substituted porphyrin (H(2)oep) coordinate with the corresponding bond distance of 1.97 A. The shorter distance of H(2)oep is ascribed to the flexibility of the porphyrin ring, and the much greater rate for the formation of the Cu(II)-SAT complex of H(2)oep than those for the meso-substituted porphyrins is interpreted as due to a small energetic loss at the porphyrin deformation step during the formation of the Cu(II)-SAT complex. The overall formation constants, beta(n), of [Cu(H(2)O)(n)()(an)(6)(-)(n)](2+) for the water addition in aqueous AN were spectrophotometrically determined at 298 K as follows: log(beta(1)/M(-1)) = 1.19 +/- 0.18, log(beta(2)/M(-2)) = 1.86 +/- 0.35, and log(beta(3)/M(-3)) = 2.12 +/- 0.57. The structure parameters around the Cu(II) ion in [Cu(H(2)O)(n)(an)(6-n)](2+) were determined using XAFS spectroscopy.     

Effect of surface viscosity on the vibration of microcantilevers

Using the theory of beam bending and the theory of surface rheology, the equation describing the effect of a surface viscous film on the vibration of an elastic microcantilever is derived. A generalized solution for the vibration of the microcantilever is obtained, which depends on the boundary conditions and the surface viscosity. There is a phase lag between the externally harmonic excitation and the microcantilever response due to the energy loss from surface flow. For small energy dissipation with negligible surface energy, the maximum energy loss occurs approximately at the natural frequencies of the microcantilever.     

紫杉醇微悬臂梁免疫传感器方法的研究

以巯基化的紫杉醇单抗修饰微梁镀金表面,制备了高灵敏的紫杉醇微悬臂梁免疫传感器.利用酶联免疫吸附测定方法对巯基化前后紫杉醇单抗的活性变化,以及巯基化单抗在微梁上的修饰进行检测与验证.采用紫杉醇微悬臂梁免疫传感器对不同浓度的紫杉醇溶液进行检测.结果表明:虽然巯基化后紫杉醇单抗的活性降低了18.6%,但巯基化紫杉醇单抗可以修...     

Effects of catechins on superoxide and hydroxyl radical

Superoxide (O2-.) was reduced by the addition of superoxide dismutase (SOD: O2-. scavenger) and catechins. In competitive reactions utilizing different concentrations of spin-trap agent, the IC50 values of each sample were changed. With regard to the Cu2+/H2O2 and Fe2+/H2O2 reaction systems, metal chelater, hydroxyl radical (.OH) scavenger and catechins eliminated the levels of .OH. For the Cu2+/H2O2 reaction systems, the IC50 for .OH scavenger changed, but that for metal chelater and catechins did not. However, for the Fe2+/H2O2 reaction system, the IC50 for .OH scavenger and catechins changed, whereas that for metal chelater did not. The ESR signal for free Cu2+ was changed by addition of metal chelater and catechins. In the spectrophotometer experiments, it was confirmed that the CuCl2 spectrum was changed by addition of metal chelater and catechins but not by .OH scavenger. Conversely, the FeSO4 spectrum was not changed by addition of .OH scavenger or catechins, but was altered by metal chelater. Lipid peroxidation was inhibited by catechins in a concentration-dependent manner. Therefore, it was suggested that the catechins did not scavenge directly the generated .OH from the Cu2+/H2O2 reaction system, but inhibited the generation of .OH by acting on the Cu2+/H2O2 reaction system. On the other hand, with respect to the .OH generated from the Fe2+/H2O2 reaction system, it was suggested that the catechins had a direct scavenging capacity of the .OH, but had little chelating activity of iron. It was confirmed that catechins have the ability to scavenge for O2-. as well as .OH and to inhibit the generation of .OH by chelation with metal ions.     

Solution [Cu(amm)]2+ is a strongly solvated square pyramid: a full account of the copper K-edge XAS spectrum within single-electron theory

The solution structure of Cu(II) in 4 M aqueous ammonia, [Cu(amm)](2+), was assessed using copper K-edge extended X-ray absorption fine structure (EXAFS) and Minuit XANes (MXAN) analyses. Tested structures included trigonal planar, planar and D2d -tetragonal, regular and distorted square pyramids, trigonal bipyramids, and Jahn-Teller distorted octahedra. Each approach converged to the same axially elongated square pyramid, 4 x Cu-Neq=2.00+/-0.02 A and 1 x Cu-Nax=2.16+/-0.02 A (EXAFS) or 2.20+/-0.07 A (MXAN), with strongly localized solvation shells. In the MXAN model, four equatorial ammonias averaged 13 degrees below the Cu(II) xy-plane, which was 0.45+/-0.1 A above the mean N4 plane. When the axial ligand equilibrium partial occupancies of about 0.65 ammonia and 0.35 water were included, EXAFS modeling found Cu-Lax distances of 2.16 and 2.31 A, respectively, reproducing the distances found in the crystal structures of [Cu(NH3)5](2+) and [Cu(NH3)4(H2O)](2+). A transverse axially localized solvent molecule was found at 2.8 A (EXAFS) or 3.1 A (MXAN). Six second-shell solvent molecules were also found at about 3.4+/-0.01 (EXAFS) or 3.8+/-0.2 A (MXAN). The structure of Cu(II) in 4 M pH 10 aqueous NH 3 may be notationally described as {[Cu(NH 3)4.62(H2O)0.38](solv)}(2+).6solv, solv=H2O, NH 3. The prominent shoulder and duplexed maximum of the rising K-edge XAS of [Cu(amm)](2+) primarily reflect the durable and well-organized solvation shells, not found around [Cu(H2O)5](2+), rather than two-electron shakedown transitions. Not accounting for solvent scattering thus may confound XAS-based estimates of metal-ligand covalency. [Cu(amm)](2+) continues the dissymmetry previously found for the solution structure of [Cu(H2O)5](2+), again contradicting the rack-bonding theory of blue copper proteins.