Reduction of polyatomic interferences in biological material using dynamic reaction cell ICP-MS

An analytical method is described for the routine quantification of five elements (As, Cr, Fe, Ni, and Se) in plants and animal feedstuffs using dynamic reaction cell inductively coupled plasma mass spectrometry (ICP-DRC-MS) after microwave digestion. Methane (for Cr, Fe, Ni, and Se) and oxygen (for As) were used as reaction gases to reduce polyatomic interferences. Optimization of the gas flow rate and the quadrupole dynamic bandpass tuning parameter (RPq) was carried out for the method. Detection limits (LOD) were in the range of 0.03–0.65 µg L^? 1 and were significantly lower compared to the standard mode without DRC. The trueness of the method was tested using three reference materials from Round robin tests. Results were well in accordance with the certified values. Furthermore, DRC data were examined by analyzing the same samples using sector field ICP-MS (SF-ICP-MS) and an ICP-MS equipped with collision cell technology (ICP-CCT-MS). The data obtained were in the confidence range of the reference material, too. The investigated method was applied for the analysis of grass and corn silage samples.     

Heavy elements concentrations,physiochemical characteristics and natural radionuclides levels along the Saudi coastline of the Gulf of Aqaba

This paper represents the first work on the concentrations of heavy elements, physiochemical characteristics and activity levels of the naturally occurring radionuclides in the Saudi Arabian coastline of the Gulf of Aqaba. Concentrations of 19 heavy elements were measured, namely: Ag, Al, As, Ba, Be, Cd, Co, Cr, Cu, Fe, Hg, Mn, Mo, Ni, Pb, Sb, Se, V and Zn. The radioactivity levels of ²³⁸U, ²³²Th and ⁴⁰K were estimated to be: 17 ± 1.7, 22.5 ± 3.7 and 649.6 ± 64.2 Bq kg^?1, respectively. The measurements were carried out using inductively coupled plasma-mass spectrometry (ICP-MS). In addition, physiochemical characteristics of 19 sediment samples (i.e., saturation percentage, pH, electrical conductivity, organic matter, cation exchange capacity and content of clay, silt and sand) have been determined. Indications for high correlation between most heavy elements are found. The correlation between heavy elements and the radionuclides ²³⁸U, ²³²Th and ⁴⁰K was generally significant.     

Determination of trace impurities in titanium dioxide by slurry sampling electrothermal atomic absorption spectrometry

A slurry sampling electrothermal atomic absorption spectrometry method for the determination of Al, Ca, Cd, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, Ni, Pb, Sr, Tl and Zn in powdered titanium dioxide is described. The behaviour of the titanium matrix in the atomizer and its interferences with the determination of Al, Fe, Co, Ni and Mn were studied. A tungsten carbide modified graphite tube was used to improve the signal shape and the repeatability for the determination of Fe. For all elements, except for Cd and Pb, quantification by a calibration curve established with aqueous standards was possible. No chemical modifier was used throughout in order to minimize contamination. For the contamination risk elements such as Ca, Fe, K, Mg, Na and Zn, the slurry sampling technique allows to achieve limits of detection (3σ of the blank) 5–20 times lower than the solution technique, resulting for these elements in values of 1, 3, 0.5, 0.5, 0.9 and 2 ng g⁻¹, respectively, and, generally being in the range of 0.2 ng g⁻¹ (Cd) to 10 ng g⁻¹ (Al and Tl). The results obtained by the slurry sampling technique are compared with those of other independent methods including four solution methods and neutron activation analysis.     

Ti in dilute slurries of TiO2 nanoparticles by in-torch vaporization sector field inductively coupled plasma-mass spectrometry☆

A Re coil-filament in-torch vaporization (ITV) sample introduction system was interfaced to a sector field inductively coupled plasma-mass spectrometry (SFICP-MS) system. In this first report on an un-optimized ITV-SF-ICP-MS system, detection limits were established using 5 μL volumes of 100 pg mL^− 1 standard solutions, translating to 0.5 pg absolute. Such absolute amounts of a dried solution are near or below the detection limit of many ICP-based techniques. The absolute detection limits for Cd, Eu, Pb, Ti, U and Zn were in the 0.2–2 fg range (or, in the 10's of millions to millions of atoms for Pb, Cd, Zn and Ti, about one million atoms for U and about 800 thousand for Eu). These absolute detection limits along with the ability of ITV to handle minute amounts of discrete samples (thus eliminating memory effects from nanoparticles adhering to the walls of pneumatic nebulization sample introduction systems and from clogging of the mass spectrometer orifice), use of sonicated water-based slurries (that eliminated contamination from acid digestion reagents or from slurry stabilization reagents), and elimination of oxygen containing molecular ion interferences due to use of dry samples enabled concentration determinations of Ti (and consequently of TiO₂) in pg mL^− 1 concentrations of slurries of manufactured, 20 nm diameter TiO₂ nanoparticles.     

Controlled dissolution of silicon dioxide layers for depth resolved multielement analysis by inductively coupled plasma-mass spectrometry

Dissolution procedures were developed to control the number of surface layers removed, in an attempt to achieve depth resolved analysis by inductively coupled plasma-mass spectrometry (ICP-MS). NIST 612 glass was chosen because it is a homogeneous material with many elements at interesting concentrations, ~ 50 ppm. Varying dissolution time and HF concentration resulted in the reproducible removal of SiO₂ layers as thin as 70 Å deep. Dissolved trace metals were determined after dilution by inductively coupled plasma-mass spectrometry (ICP-MS) with a magnetic sector instrument. The amount removed was determined from the concentration of a major element, Ca. With the exception of Zn, trace metal concentrations agreed reasonably well with their certified values for removal depths of 500, 300 and 150 Å. Zinc concentration was significantly high in all dissolutions indicating either a contamination problem or that Zn is removed at a faster rate than Ca. For the dissolutions that removed 70 Å of SiO₂, Cr, Mn, Co, Sr, Cd, Ce, Dy, Er, Yb and U recovery results agreed with their certified values (~ 50 ppm); Ti, As, Mo, Ba, and Th could not be determined because net intensities were below 3σ of the blank; and measured concentrations for Cu, Pb and Zn were well above the certified values.     

Determination of sulfur by molecular absorption of carbon monosulfide using a high-resolution continuum source absorption spectrometer and an air-acetylene flame

A standard air-acetylene flame, attached to a high-resolution continuum source atomic absorption spectrometer, was used to determine sulfur via measurements of selected rotational lines of carbon monosulfide (CS) formed in the flame. The lines are part of the strong molecular absorption system around 258 nm. Their half-widths in the order of a few picometers are comparable to common atomic lines. The analytical method is characterized by simplicity, rapidity, reliability, and robustness. Potential chemical and spectral interferences were tested using nitric, hydrochloric, perchloric and hydrofluoric acids at concentrations up to 5% (v/v), and solutions of Al, Ca, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, and Pb at concentrations up to 2000 mg L⁻¹. The only serious spectral interference occurred with Pb at concentrations higher than 200 mg L⁻¹, which is due to the formation of lead sulfate in the solution. The limit of detection achieved for sulfur was 2.4 mg L⁻¹, using the CS line at 258.056 nm and a measurement time of 5 s. A linear dynamic range of more than 3 orders of magnitude was obtained. The analytical results were verified by means of standard reference materials, yielding good precision and accuracy.     

Biomonitoring of atmospheric trace element deposition around an industrial town in Ghana

Parmelia sulcata lichen species have been used to study the atmospheric deposition of heavy metals and other toxic elements around an industrial area in Ghana. Natural soil samples were collected at all the sampling points and analysed in order to investigate surface accumulation of the heavy metals. The sampling points used for the study were: Afienya, Doryemu Cemetery and Doryemu River. The surface accumulation of the heavy metals would be used to examine the correlation of the elements in the lichen and soil samples in order to separate contributions from atmospheric deposition and from that of soil minerals. Thermal neutron activation analysis techniques employing a 30 kW tank-in-pool research reactor operating at a thermal neutron flux of 5×10¹¹ s⁻¹ cm⁻² was used to determine Al, Cr, Mn, Fe, Ti, Th and V in both the lichen and soil samples. The level of contamination was quantified using the enrichment factor approach. This approach was adopted in order to ascertain whether these elements are enriched in the soil or in the atmosphere. The sampling points were enriched in the atmosphere with Cr, Mn, Fe, Ti, Th and V in the decreasing order of Afienya, Doryemu Cemetery and Doryemu River.     

Evaluation of on-line desalter-inductively coupled plasma-mass spectrometry system for determination of Cr(III), Cr(VI), and total chromium concentrations in natural water and urine samples

We have developed a simple and convenient method for the determination of Cr(III), Cr(VI), and the total chromium concentrations in natural water and urine samples that use a flow injection on-line desalter-inductively coupled plasma-mass spectrometry system. When using aqueous ammonium chloride (pH 8) as the stripping solution, the severe interference from sodium in the matrix can be eliminated prior to inductively coupled plasma-mass spectrometry measurement, and the Cr(VI) level can be determined directly. To determine the total concentration of Cr in natural water and urine samples, we used H₂O₂ or HNO₃ to decompose the organic matter and convert all chromium species into the Cr(VI) oxidation state. To overcome the spectral interference caused by the matrix chloride ion in the resulting solutions, we employed cool plasma to successfully suppress chloride-based molecular ion interference during the inductively coupled plasma-mass spectrometry measurement. By significantly eliminating interference from the cationic and anionic components in the matrices prior to the inductively coupled plasma-mass spectrometry measurement, we found that the detection limit reached 0.18 μg L^− 1 (based on 3 sigma). We validated this method through the analysis of the total chromium content in two reference materials (NIST 1643c and 2670E) and through measuring the recovery in spiked samples.     

Heavy metals contamination in roadside soil near different traffic signals in Dubai,United Arab Emirates

The present research was conducted to study heavy metal contamination in roadside soil viz. (i) at sites having more than two traffic signals (ii) roads having only one traffic signal and (iii) roads having no traffic signals. The samples were collected and analyzed for seven heavy metals i.e. cadmium (Cd), lead (Pb), copper (Cu), nickel (Ni), iron (Fe), manganese (Mn) and zinc (Zn) by Atomic Absorption Spectroscopy (AAS) following the acid digestion of the respective soil samples. The range of the metals observed in soil having more than two traffic signals were Cd (0.17–1.01), Pb (259.66–2784.45), Cu (15.51–65.90), Ni (13.31–98.13), Fe (325.64–5136.37), Mn (57.95–166.43), and Zn (91.34–166.43) mg kg^?1 respectively. Similarly, the range of metals analyzed in samples collected from the roadside having only one traffic signal were Cd (nd–0.80), Pb (145.95–308.09), Cu (0.82–18.04), Ni (18.29–59.36), Fe (88.51–3649.42), Mn (25.88–147.34) and Zn (8.97–106.11 mg kg ^?1) respectively. However, the range of metals at roads having no traffic signals were Cd (0.0–0.57), Pb (8.34–58.20), Cu (2.88–5.81), Ni (3.34–73.80), Fe (55.34–332.81), Mn (2.98–98.73) and Zn (1.23–46.6 mg kg^?1) respectively. Cd, Cu, Ni, Fe, Mn and Zn in soil were present within the normal range of background levels, whereas lead was reported in high concentration. The level of lead had a correlation with the traffic density attributing its origin to vehicular exhaust. The values from three different sites of monitoring suggest that automobiles are a major source of the studied metals for the roadside environment.     

Development of a solid phase extraction method for the multielement determination of trace metals in natural waters including sea-water by FI-ICP-MS

An automated solid phase extraction method by flow analysis on-line inductively coupled plasma mass spectrometry (FI-ICP-MS) for the determination of cobalt, chromium, nickel, cadmium, manganese, zinc, copper and lead in sea-water and other natural waters is described. The system is based on retention of the analytes onto a minicolumn packed with a chelating resin, 1,5-bis (2-pyridyl)-3-sulphophenyl methylene thiocarbonohydrazide immobilized on aminopropyl-controlled pore glass, placed in the injection valve of a simple flow manifold. The effects of chemical and flow variables were investigated and selected as a compromise between sensitivity and sampling frequency. So, the sample solutions (adjusted to pH 8.0 ± 0.5) were passed through the column. After washing the column with water, the adsorbed metals were subsequently eluted into the plasma with 4% m/m nitric acid. Detection limits of the trace metals (180 s sample loading time at a sample flow rate of 0.7 mL min^? 1; sampling frequency 8.6 h^? 1) were 0.002 μg L^? 1 for Co, 0.057 μg L^? 1 for Cr, 0.117 μg L^? 1 for Ni, 0.004 μg L^? 1 for Cd, 0.210 μg L^? 1 for Mn, 0.260 μg L^? 1 for Zn, 0.030 μg L^? 1 for Cu and 0.020 μg L^? 1 for Pb, with enrichment factors between 2.2 and 6.8. The accuracy of the proposed method was checked with certified reference materials (CRMs) of sea-water SLEW 3, LGC6016 and CASS-5, river water SLRS-5 and fortified lake water TMDA-54.4. The results from the determination of these metals were in agreement with the certified values and recovery values ranged between 92.2 and 110.6%. The method was applied to the determination of these metal ions in sea-water samples collected in the Málaga Bay in order to realize a pilot study necessary to generate preliminary information on which to base a more detailed pollution study by heavy metals of the Bay.     

Analysis of total and dissolved heavy metals in surface water of a Mexican polluted river by total reflection X-ray fluorescence spectrometry

The present area of study is located in the Upper Course of the Lerma River (UCLR). The Lerma is one of the most important rivers of Mexico, where it drains highly populated and industrialized regions. The aim of the present study is to determine the heavy metal concentration of Cr, Mn, Fe, Cu and Pb in dissolved and total phases of the UCLR by means of Total Reflection X-ray Fluorescence Spectrometry (TXRF). The surface water samples were collected at 8 sites distributed following the stream flow direction of the river. Four sampling campaigns were carried out in each site in a 1-year period. A sample preparation method was applied in order to obtain the total and dissolved fraction and to destroy the organic matter. The total heavy metal average concentration decrease in the following order: Fe (2566 μg/L) > Mn (300 μg/L) > Cu (66 μg/L) > Cr (21 μg/L) > Pb (15 μg/L). In general, the heavy metal concentrations in water of the UCLR are below the maximum permissible limits.     

Fe-N/C catalysts for oxygen reduction based on silicon carbide derived carbon

Two different Fe-N/C(SiC) catalysts (Fe + Bipyr/C(SiC) and Fe + Phen/C(SiC)) for oxygen reduction based on silicon carbide derived carbon were synthesized and investigated in 0.1 M KOH aqueous solution by rotating disc electrode method. It was found that the electrocatalytic activity and stability are significantly influenced by the change of the nitrogen ligand in the catalyst. Comparable current density values obtained for 20%Pt-Vulcan electrode could be achieved for Fe + Bipyr/C(SiC) and Fe + Phen/C(SiC) catalysts in alkaline media. The durability tests (~ 150 h) showed that the decrease of the activity for Fe + Bipyr/C(SiC) and Fe + Phen/C(SiC) is only 0.5 mV h^− 1 and 0.17 mV h^− 1, respectively. The Fe + Bipyr/C(SiC) catalyst demonstrated higher activity in the RDE measurements, but during the long-term test the Fe + Phen/C(SiC) catalyst prove to be more stable than Fe + Bipyr/C(SiC).     

Thermodynamic analysis of sorption isotherms of chromium(VI) anionic species on reed biomass

A new sorbent material for removing Cr(VI) anionic species from aqueous solutions has been investigated. Adsorption equilibrium and thermodynamics of Cr(VI) anionic species onto reed biomass were studied at different initial concentrations, sorbent concentrations, pH levels, temperatures, and ionic strength. Equilibrium isotherm was analyzed by Langmuir model. The experimental sorption data fit the model very well. The maximum sorption capacity of Cr(VI) onto reed biomass was found to be 33 mg · g^?1. It was noted that the Cr(VI) adsorption by reed biomass decreased with increase in pH. An increase in temperature resulted in a higher Cr(VI) loading per unit weight of the adsorbent. Removal of Cr(VI) by reed biomass seems to be mainly by chemisorption. The change in entropy (ΔS^°) and heat of adsorption (ΔH^°) for Cr(VI) adsorption on reed biomass were estimated as 2205 kJ · kg^?1 · K^?1 and 822 kJ · kg^?1, respectively. The values of isosteric heat of adsorption varied with the surface loading of Cr(VI).     

Determination of lead,cadmium and mercury in blood for assessment of environmental exposure: A comparison between inductively coupled plasma–mass spectrometry and atomic absorption spectrometry

A biomonitoring method for the determination of Pb, Cd, and Hg at background levels in whole blood by inductively coupled plasma-mass spectrometry is described. While this method was optimized for assessing Pb, Cd and Hg at environmental levels, it also proved suitable for assessing concentrations associated with occupational exposure. The method requires as little as 200 μl of blood that is diluted 1 + 49 for direct analysis in the inductively coupled plasma-mass spectrometer. Method performance is compared to well-established AAS methods. Initial method validation was accomplished using National Institute of Standards and Technology (NIST) Standard Reference Material 966, Toxic Metals in Bovine Blood. Method detection limits (3s) are 0.05 μg dl^− 1 for Pb, 0.09 μg l^− 1 for Cd; and 0.17 μg l^− 1 for Hg. Repeatability ranged from 1.4% to 2.8% for Pb; 3% to 10% for Cd; and 2.6% to 8.8% for Hg. In contrast, AAS method detection limits were 1 μg dl^− 1, 0.54 μg l^− 1, and 0.6 μg l^− 1, for Pb, Cd, and Hg, respectively. Further performance assessments were conducted over a 2-year period via participation in four international External Quality Assessment Schemes (EQAS) operated specifically for toxic metals in blood. This includes schemes operated by (a) the New York State Department of Health's Wadsworth Center, Albany, NY, USA (b) L′Institut National de Santé Publique du Québec, Centre de Toxicologie du Québec, Canada, (c) Friedrich-Alexander University, Erlangen, Germany, and (d) the University of Surrey, Guildford, UK Trace Elements scheme. The EQAS data reflect analytical performance for blind samples analyzed independently by both inductively coupled plasma-mass spectrometry and AAS methods.     

Laser ablation–inductively coupled plasma–dynamic reaction cell–mass spectrometry for the multi-element analysis of polymers

In this work, the potential of laser ablation–inductively coupled plasma–mass spectrometry for the fast analysis of polymers has been explored. Different real-life samples (polyethylene shopping bags, an acrylonitrile butadiene styrene material and various plastic bricks) as well as several reference materials (VDA 001 to 004, Cd in polyethylene) have been selected for the study. Two polyethylene reference materials (ERM-EC 680 and 681), for which a reference or indicative value for the most relevant metals is available, have proved their suitability as standards for calibration.Special attention has been paid to the difficulties expected for the determination of Cr at the μg g^− 1 level in this kind of materials, due to the interference of ArC⁺ ions on the most abundant isotopes of Cr. The use of ammonia as a reaction gas in a dynamic reaction cell is shown to alleviate this problem, resulting in a limit of detection of 0.15 μg g^− 1 for this element, while limiting only modestly the possibilities of the technique for simultaneous multi-element analysis. In this regard, As is the analyte most seriously affected by the use of ammonia, and its determination has to be carried out in vented mode, at the expense of measuring time.In all cases studied, accurate results could be obtained for elements ranging in content from the sub-μg g^− 1 level to tens of thousands of μg g^− 1. However, the use of an element of known concentration as internal standard may be needed for materials with a matrix significantly different from that of the standard (polyethylene in this work).Precision ranged between 5% and 10% RSD for elements found at the 10 μg g^− 1 level or higher, while this value could deteriorate to 20% for analytes found at the sub-μg g^− 1 level. Overall, the technique evaluated presents many advantages for the fast and accurate multi-element analysis of these materials, avoiding laborious digestion procedures and minimizing the risk of analyte losses due to the formation of volatile compounds.     

Synthesis and spectroscopic characterization of new tetradentate Schiff base and its coordination compounds of NOON donor atoms and their antibacterial and antifungal activity

New Schiff base (H₂L) ligand is prepared via condensation of o-phthaldehyde and 2-aminobenzoic acid in 1:2 ratio. Metal complexes are prepared and characterized using elemental analyses, IR, solid reflectance, magnetic moment, molar conductance, ¹H NMR, ESR and thermal analysis (TGA). From the elemental analyses data, the complexes were proposed to have the general formulae [MCl(L)(H₂O)]·2H₂O (where M = Cr(III) and Fe(III)); [M(L)]·yH₂O (where M = Mn(II), Ni(II), Cu(II) and Zn(II), y = 1–2) and [M(L)(H₂O)_n]·yH₂O (where M = Co(II) (n = y = 2), Co(II) (n = y = 1), Ni(II) (n = 2, y = 1). The molar conductance data reveal that all the metal chelates were non-electrolytes. IR spectra show that H₂L is coordinated to the metal ions in a bi-negative tetradentate manner with NOON donor sites of the azomethine-N and carboxylate-O. The ¹H NMR spectral data indicate that the two carboxylate protons are also displaced during complexation. From the magnetic and solid reflectance spectra, it was found that the geometrical structure of these complexes are octahedral (Cr(III), Fe(III), Co(II) and Ni(II)), square planar (Cu(II)), trigonal bipyramidal (Co(II)) and tetrahedral (Mn(II), Ni(II) and Zn(II)). The thermal behaviour of these chelates showed that the hydrated complexes losses water molecules of hydration in the first step followed immediately by decomposition of the ligand molecule in the subsequent steps. The biological activity data show that the metal complexes to be more potent/antibacterial than the parent Shciff base ligand against one or more bacterial species.     

Elemental analysis by surface-enhanced Laser-Induced Breakdown Spectroscopy combined with liquid–liquid microextraction

In this work, the possibility of using Laser-Induced Breakdown Spectrometry (LIBS) combined with liquid–liquid microextraction techniques is evaluated as a simple and fast method for trace elemental analysis. Two different strategies for LIBS analysis of manganese contained in microdroplets of extraction solvent (Triton X-114) are studied: (i) analysis by direct laser irradiation of microdroplets; and (ii) analysis by laser irradiation of microdroplets dried on metallic substrates (surface-enhanced LIBS — SENLIBS). Experiments were carried out using synthetic samples with different concentrations of manganese in a 10% w/w Triton X-114 matrix. The analysis by direct laser irradiation of microdroplets showed low precision, sensitivity and poor linearity across the concentration range evaluated (R² < 0.95). On the other hand, the SENLIBS method of analysis improved the sensitivity, the precision and the linearity of the calibration curve with respect to the direct analysis of microdroplets. In comparison with experimental results obtained by direct analysis, SENLIBS also allowed several replicate measurements to be carried out in a single microdroplet. The limit of detection obtained was 6 μg g^− 1 of Mn.     

Chemometric interpretation of digital image colorimetry. Application for titanium determination in plastics

Basic color data (RGB) obtained from digital images were studied by Factorial Analysis. The results demonstrated that individual RGB data represent different contributions. On the other hand, the total intensity of colors is proposed like a fourth variable in digital colorimetry and can be interpreted as complementary information related to the conditions of image capture in digital cameras. The chemometric study evidences that the analytical information, for quantitative applications, is formed by two parts: deterministic, with valuable analytical interest, and undeterministic or unvaluable analytical information. These results were revealed after variable reduction and data compression, using Principal Component Analysis and Fourier Transform, respectively.The digital colorimetric study was applied to the reaction of Ti(IV) with hydrogen peroxide at 0.09 M sulfuric acid media. They produce a yellow–orange complex solution. And their RGB intensities could be linearly correlated with Ti(IV) concentration in the range of 2.0 to 30.0 mg l^? 1. In the best conditions, using the intensity of the blue color, a simple and fast method for Ti(IV) determination could be developed. Its detection limit was found to be (criterion 3 s) 0.6 mg l^? 1 and the rsd for 10.0 mg l^? 1 of Ti(V) was 4.8%.Calibration by artificial neural nets represents an option that improves the answer to low concentration.Applications of the colorimetric method to the analysis of Ti in representative plastics, with content in mg g^? 1 level, are presented. Its validity was assessed by ICP-AES with standard addition. Results were in satisfactory agreement. The method is fast and reduces the analysis time.     

Determination of NiII(3-OMe-salophene) in MCF7 and HT29 cancer cell lines using HR-CS-AAS and in serum albumin using LC with monolithic silica

A high-resolution continuum source atomic absorption spectrometric method was developed and validated for the determination of Ni^II(3-OMe-salophene) (a complex with anticancer activity in vitro) in MCF7 and HT29 cancer cell lines. The primarily most sensitive line 232.003 nm was selected for analysis. Compared to the standard nickel, the absorbance values obtained for Ni^II(3-OMe-salophene) complex was at least 93% at the upper end of linear range of the calibration curve. The use of common matrix modifiers including magnesium nitrate, palladium nitrate, ammonium hydrogen phosphate, lanthanum chloride and calcium nitrate brought no significant improvement in the GF AAS measurement. The dynamic linear working range of the calibration curve was found to be between 2.16 and 12.0 μg L^? 1 (ppb). This covers a concentration range of the complex from 0.036 μM to 0.204 μM. Typical coefficients of variation (n = 6) ranged from 0.2% to 6.7% for Ni in Ni^II(3-OMe-salophene). Detection and quantitation limits were 0.65 and 2.16 μg L^? 1 (ppb), respectively. The proposed method has been successfully applied to the analysis of Ni^II(3-OMe-salophene) complex in cell lines of breast cancer (MCF7) and colon cancer (HT29). However, being based on the determination of nickel in the salophene complex, the method was unsuitable for the quantitation of Ni^II(3-OMe-salophene) in serum albumin, which originally contains significant amount of nickel. For this purpose, a high performance liquid chromatographic method with a monolithic silica RP-18e column has been developed to quantitate the complex in serum albumin. The developed chromatographic method depends on detecting the whole complex in serum rather than the bounded nickel. A mobile phase consisting of 25 mM phosphate buffer pH 3/methanol (30:70, v/v) was pumped at a flow rate of 1 mL min^? 1. The eluted complex was monitored at a wavelength of 250 nm. The dynamic linear working range of the calibration curve for the developed LC method was found to be between 100 and 20,000 μg L^? 1 (0.23–46.18 μM). Detection and quantitation limits were 30 and 100 μg L^? 1 (ppb), respectively.     

Application of Box–Behnken design in the optimisation of an on-line pre-concentration system using knotted reactor for cadmium determination by flame atomic absorption spectrometry

The present paper proposes an on-line pre-concentration system for cadmium determination in drinking water using flame atomic absorption spectrometry (FAAS). Cadmium(II) ions are retained as 1-(2-pyridylazo)-2-naphthol (PAN) complex at the walls of a knotted reactor, followed of elution using hydrochloric acid solution. The optimization was performed in two steps using factorial design for preliminary evaluation and a Box–Behnken design for determination of the critical experimental conditions. The variables involved were: sampling flow-rate, reagent concentration, pH and buffer concentration, and as response the analytical signal (absorbance). The validation process was performed considering the parameters: linearity and other characteristics of the calibration curve, analytical features of on-line pre-concentration system, precision, effect of other ions in the pre-concentration system and accuracy. Using the optimized experimental conditions, the procedure allows cadmium determination with a detection limit (3 σ / S) of 0.10 μg L^− 1, a quantification limit (10 σ / S) of 0.33 μg L⁻¹, and a precision, calculated as relative standard deviation (RSD) of 2.7% (n = 7) and 2.4% (n = 7) for cadmium concentrations of 5 and 25 μg L^− 1, respectively. A pre-concentration factor of 18 and a sampling frequency of 48 h⁻¹ were obtained. The recovery for cadmium in the presence of several ions demonstrated that this procedure could be applied for the analysis of water samples. The method was applied for cadmium determination in drinking water samples collected in Salvador City, Brazil. The cadmium concentrations found in five samples were lower than the maximum permissible levels established by the World Health Organization.