Flame atomic absorption determination of trace amounts of cadmium after preconcentration using a thiol-containing task-specific ionic liquid

Dispersive liquid-liquid microextraction (DLLME) based on a task-specific ionic liquid (TSIL) was developed for the extraction and preconcentration of trace amounts of cadmium from aqueous samples, followed by flame atomic absorption spectrometry (FAAS) determination. In the proposed approach, cadmium ions are extracted from aqueous samples using small volumes of trioctylmethylammonium thiosalicylate (TOMATS) dissolved in acetone. TOMATS is a thiol-containing TSIL that can form metal thiolate complexes due to the chelating effect of the ortho-positioned carboxylate group relative to the thiol functionality. The main parameters affecting the performance of DLLME based on TSIL, such as pH, amount of TOMATS, extraction time, injection volume, salt addition, and centrifugation time, were optimized. Under optimum conditions, an LOD of 1.16 ng/mL and a good RSD of 1.8% at 60.0 ng/mL were obtained (n=7). The proposed method was applied to tap water, wastewater, well water, and milk samples. The results showed that DLLME based on TSIL combined with FAAS is a rapid, simple, sensitive, selective, low cost, volatile organic solvent-free, and efficient analytical method for the separation and determination of trace amounts of cadmium ions.     

Concentration and determination of trace amounts of chlorinated pesticides in aqueous samples

Summary A method for the quantitative analysis of the organochloro-pesticides heptachlor, dieldrin, DDT and aldrin in water, using the HPLC technique of on-line trace enrichment, has been developed. A standard HPLC isocratic analytical system was employed the principle modification being the incorporation of a short pre-column across the sample loop connections of a Rheodyne 7125 valve to serve as the trace enrichment column. Pesticide recoveries of >95% were achieved at sample flow rate of 5–15 ml/min by employing stainless steel fittings throughout the system and with 5% methanol included in the pesticide sample reservoir. The pesticides were concentrated onto a 50 mm, 10 m Spherisorb ODS column; analysis was performed on a 25 cm, 5 m Spherisorb ODS column with methanol-water (7525) elution; detection was by UV absorption measurement at 220 mm and 0.64 AUFS.Resolution achieved was >=1.16 and selectivity >=1.14. 100 ml aqueous samples allow ppb detection of the named pesticides in real samples. Total analysis time including concentration and chromatography was less than 30 minutes.     

Headspace liquid-phase microextraction using ionic liquid as extractant for the preconcentration of dichlorodiphenyltrichloroethane and its metabolites at trace levels in water samples

A novel technique, high temperature headspace liquid-phase microextraction (HS-LPME) with room temperature ionic liquid (RTIL), 1-butyl-3-methylimidazolium hexafluorophosphate ([C₄MIM][PF₆]) as extractant, was developed for the analysis of dichlorodiphenyltrichloroethane (p,p′-DDT and o,p′-DDT) and its metabolites including 4,4′-dichlorodiphenyldichloroethylene (p,p′-DDE) and 4,4′-dichlorodiphenyldichloroethane (p,p′-DDD) in water samples by high performance liquid chromatography with ultraviolet detection. The parameters such as salt content, sample pH and temperature, stirring rate, extraction time, microdrop volume, and sample volume, were found to have significant influence on the HS-LPME. The conditions optimized for extraction of target compounds were as follows: 35% NaCl (w/v), neutral pH condition, 70 °C, 800 rpm, 30 min, 10 μL [C₄MIM][PF₆], and 25 mL sample solutions. Under the optimized conditions, the linear range, detection limit (S/N = 3), and precision (R.S.D., n = 6) were 0.3-30 μg L⁻¹, 0.07 μg L⁻¹, and 8.0% for p,p′-DDD, 0.3-30 μg L⁻¹, 0.08 μg L⁻¹, and 7.1% for p,p′-DDT, 0.3-30 μg L⁻¹, 0.08 μg L⁻¹, and 7.2% for o,p′-DDT, and 0.2-30 μg L⁻¹, 0.05 μg L⁻¹, and 6.8% for p,p′-DDE, respectively. Water samples including tap water, well water, snow water, reservoir water, and wastewater were analyzed by the proposed procedure and the recoveries at 5 μg L⁻¹ spiked level were in the range of 86.8-102.6%.     

Pre-column chelation liquid chromatographic separation and determination of trace V,Cu, Co,Pd, Fe and Ni

Conditions for the separation by reversed-phase liquid chromatography (LC) of V(V), Cu(II), Co(III), Pd(II), Fe(III) and Ni(II) chelates with 2-(5-bromopyridylazo)-5-diethylaminophenol (5-Br-PADAP) were studied. Six species of metal chelates were separated successfully with methanol-acetonitrile-water (72:12:16, v/v/v) containing 0.13 M NaCl and 0.29 mM cetyltrimethylammonium bromide (pH 5.0) as the mobile phase on a Nucleosil C₁₈ (5 μm) column (250 × 4 mm i.d.).The conditions of the determination of these metal chelates are discussed. A simple and rapid method for the determination of trace amounts of V(V), Cu(II), Co(III), Pd(II) and Ni(II) simultaneously by reversed-phase LC has been developed. The detection limits are 5 × 10^?12, 1 × 10^?10, 3 × 10^?11, 5.3 × 10^?9 and 2 × 10^?10 g, respectively. The method is applied to the determination of these metals in natural waters and mineral samples.     

New sorbents and indicator powders for preconcentration and determination of trace metals in liquid samples

Two approaches to immobilize complex-forming analytical reagents (PAN, PAR, Xylenol orange, Brombenzothiazo, Crystal violet, Cadion, and Sulfochlorophenolazorhodanine) for the preparation of new sorbents and indicator powders are suggested: on-line coating of reversed-phase silica gel by reagents or doping of porous sol-gel silica with reagents. The retention of Ag, Cd, Cu(II), Co(II), Fe(III), Mn(II), Ni, Pb, and Zn on the sorbents developed was investigated. Quantitative sorption and desorption conditions were optimized. Procedures for the determination of Cd, Cu(II), Fe(III), Pb, and Zn with flame atomic absorption, spectrophotometric, and diffusion scattering spectrometric detection were elaborated. Detection limits for Cd, Cu(II), Fe(III), Pb, and Zn were 3 μg/L, 6 μg/L, 5 μg/L, 40 μg/L, and 1 μg/L, respectively. The procedures were used for the analysis of various real samples, e.g., natural and waste waters, and food. Received: 17 July 1997 / Revised: 20 January 1998 / Accepted: 5 February 1998     

New sorbents and indicator powders for preconcentration and determination of trace metals in liquid samples

Two approaches to immobilize complex-forming analytical reagents (PAN, PAR, Xylenol orange, Brombenzothiazo, Crystal violet, Cadion, and Sulfochlorophenolazorhodanine) for the preparation of new sorbents and indicator powders are suggested: on-line coating of reversed-phase silica gel by reagents or doping of porous sol-gel silica with reagents. The retention of Ag, Cd, Cu(II), Co(II), Fe(III), Mn(II), Ni, Pb, and Zn on the sorbents developed was investigated. Quantitative sorption and desorption conditions were optimized. Procedures for the determination of Cd, Cu(II), Fe(III), Pb, and Zn with flame atomic absorption, spectrophotometric, and diffusion scattering spectrometric detection were elaborated. Detection limits for Cd, Cu(II), Fe(III), Pb, and Zn were 3 μg/L, 6 μg/L, 5 μg/L, 40 μg/L, and 1 μg/L, respectively. The procedures were used for the analysis of various real samples, e.g., natural and waste waters, and food.     

Extraction and preconcentration of ultra trace amounts of beryllium from aqueous samples by nanometer mesoporous silica functionalized by 2,4-dihydroxybenzaldehyde prior to ICP OES determination

A new functionalized nanometer mesoporous silica (MCM-41) using 2,4-dihydroxybenzaldehyde (4-OHsal) was applied as an effective sorbent for solid phase extraction (SPE) of beryllium ions from aqueous solution followed by inductively coupled plasma optical emission spectrometric detection (ICP OES). The influences of some analytical parameters on the quantitative recoveries of the analyte ion were investigated in batch method. In order to perform the batch mode of SPE, known amount of sorbent was added to a test tube containing sample solution buffered at pH 7.2. After manual shaking and centrifugation the aqueous phase was decanted and beryllium was desorbed by adding 1.0 mL of 1.0 mol L^?1 HNO₃ to the sedimented sorbent. The sorbent was separated by centrifugation and the concentration of beryllium in the supernatant was determined by ICP OES. The maximum sorption capacity of the modified MCM-41 was found to be 34 mg g^?1. The sorbent exhibited good stability, reusability and fast rate of equilibrium for sorption/desorption of beryllium ions. The present method was used for preconcentration and determination of beryllium for water samples. Under optimal conditions, the limit of detection (LOD) obtained was 0.3 ng L^?1. The accuracy of the procedure was evaluated by analysis of the certified reference material (NIST 1640).     

Electrothermal vaporization dynamic reaction cell inductively coupled plasma mass spectrometry for the determination of Fe,Co, Ni,Cu, and Zn in biological samples

Slurry sampling electrothermal vaporization dynamic reaction cell inductively coupled plasma mass spectrometry (ETV-DRC-ICP-MS) has been applied to determine Fe, Co, Ni, Cu, and Zn in biological samples. The influences of instrument operating conditions and slurry preparation on the ion signals were reported. Pd was used as the modifier. The effectiveness of the ETV sample introduction technique and dynamic reaction cell in alleviating various spectral interferences in ICP-MS analysis has been demonstrated. This method has been applied to determine Fe, Co, Ni, Cu, and Zn in NIST SRM 1573a tomato leaves reference material and NRCC DORM-2 dogfish muscle reference material and also real samples such as a tea and a swordfish sample purchased locally. Since the sensitivities of the elements studied in slurry and aqueous solution were different, an analyte addition technique was used for the determinations. The analytical results of the reference materials agreed with the certified values. The precision between sample replicates was better than 6% for all determinations. The method detection limit estimated from analyte addition curves was 0.01, 0.006, 0.007, 0.004, and 0.006 μg g⁻¹ for Fe, Co, Ni, Cu, and Zn, respectively, in the original biological samples.     

Spectrophotometric determination of trace amounts of tungsten in geological samples after preconcentration on Amberlite XAD-1180

A method for the preconcentration of trace amounts of tungsten as its thiocyanate complex, using a column filled with Amberlite XAD-1180 resin, is proposed. After elution with a small volume of acetone, the analyte was determined spectrophotometrically with potassium thiocyanate and stannous chloride. The influence of several ions, as interferents, is discussed. The proposed method was applied to the determination of tungsten in geological samples with good analytical results, such as recoveries of 95% or above, relative standard deviations of 6% or below (n = 10) and a detection limit of 12 mugl(-1).     

Separation and preconcentration of trace amounts of aluminum ions in surface water samples using different analytical techniques

A separation/preconcentration of aluminum (III) (Al³⁺) has been developed to overcome the problem of high matrix species, which may interfere with the determination of trace quantity of Al³⁺ in natural water samples. The separation of Al³⁺ in water samples was carried out from interfering cations by complexing them with 2-methyle 8-hyroxyquinoline (quinaldine) on activated silica. Whereas the separated trace amounts of Al³⁺ was preconcentrated by cloud point extraction (CPE), as prior step to its determination by spectrofluorimetry (SPF) and flame atomic absorption spectrometry (FAAS). The Al³⁺ react with 8-hydroxyquinoline (oxine) and then entrapped in non-ionic surfactant Triton X-114. The main factors affecting CPE efficiency, such as pH of sample solution, concentration of oxine and Triton X-114, equilibration temperature and time period for shaking were investigated in detail. The validity of separation/preconcentration of Al³⁺ was checked by certified reference material of water (SRM-1643e). After optimization of the complexation and extraction conditions, a preconcentration factor of 20 was obtained for Al³⁺ in 10 mL of natural water samples. The relative standard deviation for 6 replicates containing 100 μg L⁻¹ of Al³⁺ was 5.41 and 4.53% for SPF and FAAS, respectively. The proposed method has been applied for determination of trace amount of Al³⁺ in natural water samples with satisfactory results.     

Cloud-point formation based on mixed micelles for the extraction, preconcentration and spectrophotometric determination of trace amounts of beryllium in water samples.

A cloud-point extraction process using a mixed micelle of the cationic surfactant cetyl pyridinium chloride (CPC) and non-ionic surfactant Triton X-114 to extract beryllium from aqueous solutions was investigated. The method is based on the color reaction of beryllium with Chrome Azurol S (CAS) in acetate buffer and the mixed micelle-mediated extraction of the complex. This complex was concentrated in a surfactant-rich phase after separation. The optimal extraction and reaction conditions (e.g. pH, reagent and surfactant concentrations, temperature, incubation and centrifuge times) were evaluated and optimized. Under the optimized conditions, the analytical characteristics of the method (e.g. limit of detection, linear range and preconcentration factor) were obtained. Linearity was obeyed in the range of 0.30 - 18 ng mL(-1) of beryllium and the detection limit of the method was 0.05 ng mL(-1). The interference effect of some cations and anions was also studied. The proposed method was successfully applied to the determination of beryllium in real water samples.     

Adsorption of acidic, basic, and neutral proteins from aqueous samples using Fe3O4 magnetic nanoparticles modified with an ionic liquid

We have prepared and characterized Fe₃O₄ nanoparticles and their binary mixtures (IL-Fe₃O₄) with 1-hexyl-3-methylimidazolium bromide as ionic liquid for use in the adsorption of lysozyme (LYS), bovine serum albumin (BSA), and myoglobin (MYO). The optimum operational conditions for the adsorption of proteins (at 0.05–2.0 mg?mL^?1) were 4.0 mg?mL^?1 of nanoparticles and a contact time of 10 min. The maximum adsorption capacities are 455, 182 and 143 mg for LYS, BSA, and MYO per gram of adsorbent, respectively. The Langmuir model better fits the adsorption isotherms, with adsorption constants of 0.003, 0.015 and 0.008 L?mg^?1, in order, for LYS, BSA, MYO. The applicability of two kinetic models including pseudo-first order and pseudo-second order model was estimated on the basis of comparative analysis of the corresponding rate parameters, equilibrium adsorption capacity and correlation coefficients. The adsorption processes are endothermic. The proteins can be desorbed from the nanoparticles by using NaCl solution at pH 9.5, and the nanoparticles thus can be recycled.

Speciation of alkyllead in aqueous samples with application of liquid membrane probe for extraction and preconcentration

Lead is known to be toxic, especially in its organic forms (organolead, OL). In the environment tetraalkyllead species are rapidly degraded by sunlight and atmospheric constituents like ozone or hydroxyl radicals. Such breakdown yields the soluble forms such as trialkyllead and dialkyllead and finally ionic lead species. The liquid membrane extraction probe (LMP) device has been developed and used as an extraction and preconcentration tool for the speciation analysis of organolead compounds by GC/MS. It allows analysis of OL species at low concentrations in complicated matrices of environmental samples. The effect of pH, stirring rate, and time that influence the extraction efficiency of OL extraction by the LMP method were optimized. The transformation of tetramethyllead in aqueous media at different concentrations of major ions K(+), Na(+), Ca(2+), Mg(2+), Cl(-), SO(4)(2-) and the application of LMP to environmental samples are presented. It was found that degradation of tetramethyllead takes between 24 and 37 days. The detection limit (LOD) of the method for all organolead species investigated is around 4.7 microg/L, with a limit of quantitation of 15 microg/L.     

On-line and off-line preconcentration of trace and ultratrace amounts of lanthanides

The need for preconcentration of trace and ultratrace amounts of lanthanides from environmental, geological and biological samples is brought out in introductory part. Both on-line and off-line preconcentration procedures developed for lanthanides since 1980 are reviewed. The preconcentration techniques covered in this review include liquid-liquid extraction (LLE), ion-exchange, co-precipitation, and solid phase or solid-liquid extraction. Separate sections are devoted to each of the preconcentration techniques employed for enrichment of individual or mixtures of lanthanides. Future trends in singular or multielement preconcentration of lanthanides are also discussed.     

A switchable ionic liquid with polarity swing-assisted regeneration properties used for the preconcentration of cadmium in biological samples

In the present study the cadmium (Cd) was determined in serum samples of psoriatic patients. The severity of psoriasis was evaluated according to criteria based on standard clinical diagnosis using Psoriasis Area Severity Index (PASI) score. In present study, an innovative tunable green solvent system based microextraction (TSS-ME) was applied for the enrichment of Cd in acid digested serum samples prior to determination with flame atomic absorption spectrometry. The hydrophobic complex of Cd-ammonium pyrrolidine thiocarbamate was extracted in a tunable solvent system which was prepared from a polybasic amine (N, N, N′, N′-tetramethyl-1, 4-diaminobutane), decanol and water system. The tunable green solvent system (TSS) which has zero ionic strength was converted to homogeneous monophasic polar hydrophilic phase via exposure to CO₂ at different pressure and time duration. Then hydrophobic enriched Cd- ammonium pyrrolidine thiocarbamate was back extracted, using HNO₃ (0.1 to 0.5 mol L⁻¹) then the second round of TSS-ME was applied. The acidic aqueous phase enrich with analyte was separated from tunable solvent. The separated TSS was easily reused for up to 10 time for preconcentration purposes without loss of its enrichment character. The smoker and nonsmoker psoriatic patients at PASI >10, have two to three folds higher Cd levels in serum samples than healthy persons.     

Determination of Cr,Fe, Co,Ni, Cu,Zn, As and Pb in liquid chemical waste by energy dispersive X-ray fluorescence

A method for simultaneous determination of Cr, Fe, Co, Ni, Cu, Zn, As e Pb in liquid chemical waste using Energy Dispersive X-Ray Fluorescence (EDXRF) technique was evaluated. A small sample amount (200 μL) was dried on a 6.35 μm thickness Mylar film at 60 °C and the analyses were carried out using an EDXRF spectrometer operated with an X-ray Mo tube (Zr filter) at 30 kV/20 mA. The acquisition time was 300 s and the Ga element was utilized as internal standard at 25 mg/L for quantitative analysis. The method trueness was assessed by spiking and the detection limit for those elements ranged from 0.39 to 1.7 mg/L. This method is notable because it assists the choice of the more appropriated waste treatment procedure, in which inter elemental interference is a matter of importance. In addition, this inexpensive method allows a non-destructive determination of the elements from ₁₉K to ₉₂U simultaneously.     

Liquid–gas–liquid technique for microextraction and preconcentration of short chain fatty acids from aqueous samples

In this study, an organic solvent‐free microextraction technique termed liquid–gas–liquid microextraction (LGLME) was applied for cleanup and preconcentration of volatile short chain fatty acids in beverages and dairy products. Various parameters affecting the extraction efficiency such as extraction time, stirring speed, sodium chloride content, concentration and volume of donor and acceptor phases, and extraction temperature were studied. Repeatability (RSD, 4.2–8.5%), correlation coefficients (0.998–0.999), LODs (10–20 μg/L) and enrichment factors (152–249) were also investigated. Recoveries were achieved in the range of 90–102% in different matrices. The presented method was applied for the analysis of target analytes in some samples such as grape juice, vinegar and dairy products.     

Determination of trace silver in environmental samples by room temperature ionic liquid-based preconcentration and flame atomic absorption spectrometry

We report on a new method for preconcentration of silver ion at trace level in environmental samples, and its subsequent determination by flame atomic absorption spectrometry (FAAS). The room temperature ionic liquid (RTIL) 1-butyl-3-methylimidazolium hexafuorophosphate and the chelator 5-(4-dimethylaminobenzylidene)-rhodanine were used for extraction. Ag(I) was back-extracted from the organic phase into thiosulfate solution and then determined via FAAS. The effects of pH, concentration of chelating agent, extraction time and temperature, amounts of ionic liquid, ionic strength and potentially interfering ions were studied. Under optimized conditions, the enhancement factor is 30 was achieved. The detection limit (3???) is 0.28?ng?mL^?1, and the relative standard deviation is 4.1% for 7 replicate determinations at 5?ng?mL^?1 of Ag(I). The method was validated by analysis of certified reference materials and applied to the determination of Ag(I) in environmental samples with satisfactory results.

Temperature-controlled ionic liquid dispersive liquid phase microextraction combined with ultra-high-pressure liquid chromatography for the rapid determination of triclosan, triclocarban and methyl-triclosan in aqueous samples

As extraction solvents, ionic liquids have green characteristics. In this study, an environmentally benign analytical method termed temperature-controlled ionic liquid dispersive liquid phase microextraction (TIL-DLME) combined with ultra-highpressure liquid chromatography (UHPLC)-tunable ultraviolet detection (TUV) was developed for the pre-concentration and determination of triclosan (TCS), triclocarban (TCC) and methyl-triclosan (M-TCS) in water samples. Significant parameters that may affect extraction efficiencies were examined and optimized, including the types and amount of ionic liquids, volume of the diluent, heating temperature, cooling time, salt effect and pH value. Under the optimum conditions, linearity of the method was observed in the ranges of 0.0100–100 μg L^?1 for TCS and M-TCS, and 0.00500–50.0 μg L^?1 for TCC with correlation coefficients (r ²) > 0.9903. The limits of detection (LODs) ranged from 1.15 to 5.33 ng L^?1. TCS in domestic water and TCC in reclaimed water were detected at the concentrations of 1.01 and 0.126 μg L^?1, respectively. The spiked recoveries of the three target compounds in reclaimed water, irrigating water, waste water and domestic water samples were obtained in the ranges of 68.4%–71.9%, 61.6%–87.8%, 58.9%–74.9% and 64.9%–92.4%, respectively. Compared with the previous dispersive liquid-liquid microextraction method (DLLME) about the determination of TCS, TCC and M-TCS, this method is not only more environmentally friendly but also more sensitive.