Comparison of laser induced breakdown spectroscopy and spark induced breakdown spectroscopy for determination of mercury in soils

Mercury is a toxic element found throughout the environment. Elevated concentrations of mercury in soils are quite hazardous to plants growing in these soils and also the runoff of soils to nearby water bodies contaminates the water, endangering the flora and fauna of that region. This makes continuous monitoring of mercury very essential. This work compares two potential spectroscopic methods (laser induced breakdown spectroscopy (LIBS) and spark induced breakdown spectroscopy (SIBS)) at their optimum experimental conditions for mercury monitoring. For LIBS, pellets were prepared from soil samples of known concentration for generating a calibration curve while for SIBS, soil samples of known concentration were used in the powder form. The limits of detection (LODs) of Hg in soil were calculated from the Hg calibration curves. The LOD for mercury in soil calculated using LIBS and SIBS is 483 ppm and 20 ppm, respectively. The detection range for LIBS and SIBS is discussed.     

Characterization of laser induced breakdown plasmas used for measurements of arsenic,antimony and selenium hydrides

Studies have been performed to characterize laser induced breakdown spectroscopy (LIBS) plasmas formed in Ar/H₂ gas mixtures that are used for hydride generation (HG) LIBS measurements of arsenic (As), antimony (Sb) and selenium (Se) hydrides. The plasma electron density and plasma excitation temperature have been determined through hydrogen, argon and arsenic emission measurements. The electron density ranges from 4.5 × 10¹⁷ to 8.3 × 10¹⁵ cm^?3 over time delays of 0.2 to 15 μs. The plasma temperatures range from 8800 to 7700 K for Ar and from 8800 to 6500 K for As in the HG LIBS plasmas. Evaluation of the plasma properties leads to the conclusion that partial local thermodynamic equilibrium conditions are present in the HG LIBS plasmas. Comparison measurements in LIBS plasmas formed in Ar gas only indicate that the temperatures are similar in both plasmas. However it is also observed that the electron density is higher in the Ar only plasmas and that the emission intensities of Ar are higher and decay more slowly in the Ar only plasmas. These differences are attributed to the presence of H₂ which has a higher thermal conductivity and provides additional dissociation, excitation and ionization processes in the HG LIBS plasma environment. Based on the observed results, it is anticipated that changes to the HG conditions that change the amount of H₂ in the plasma will have a significant effect on analyte emission in the HG LIBS plasmas that is independent of changes in the HG efficiency. The HG LIBS plasmas have been evaluated for measurements of elements hydrides using a constant set of HG LIBS plasma conditions. Linear responses are observed and limits of detection of 0.7, 0.2 and 0.6 mg/L are reported for As, Sb and Se, respectively.     

Onboard calibration igneous targets for the Mars Science Laboratory Curiosity rover and the Chemistry Camera laser induced breakdown spectroscopy instrument

Accurate characterization of the Chemistry Camera (ChemCam) laser-induced breakdown spectroscopy (LIBS) on-board composition targets is of prime importance for the ChemCam instrument. The Mars Science Laboratory (MSL) science and operations teams expect ChemCam to provide the first compositional results at remote distances (1.5–7 m) during the in situ analyses of the Martian surface starting in 2012. Thus, establishing LIBS reference spectra from appropriate calibration standards must be undertaken diligently. Considering the global mineralogy of the Martian surface, and the possible landing sites, three specific compositions of igneous targets have been determined. Picritic, noritic, and shergottic glasses have been produced, along with a Macusanite natural glass. A sample of each target will fly on the MSL Curiosity rover deck, 1.56 m from the ChemCam instrument, and duplicates are available on the ground. Duplicates are considered to be identical, as the relative standard deviation (RSD) of the composition dispersion is around 8%. Electronic microprobe and laser ablation inductively coupled plasma mass spectrometry (LA ICP-MS) analyses give evidence that the chemical composition of the four silicate targets is very homogeneous at microscopic scales larger than the instrument spot size, with RSD < 5% for concentration variations > 0.1 wt.% using electronic microprobe, and < 10% for concentration variations > 0.01 wt.% using LA ICP-MS. The LIBS campaign on the igneous targets performed under flight-like Mars conditions establishes reference spectra for the entire mission. The LIBS spectra between 240 and 900 nm are extremely rich, hundreds of lines with high signal-to-noise, and a dynamical range sufficient to identify unambiguously major, minor and trace elements. For instance, a first LIBS calibration curve has been established for strontium from [Sr] = 284 ppm to [Sr] = 1480 ppm, showing the potential for the future calibrations for other major or minor elements.     

Forms of soil organic nitrogen in a Pactola soil as seen by pyrolysis/gas chromatography/atomic emission detection (Py–GC/AED)

In this study, soil organic nitrogen (SON) forms from a Pactola forest soil were investigated by using pyrolysis–cryogenic gas chromatography/atomic emission (Py–GC/AED). The samples were taken at different soil depths of 0–12 cm, 12–25 cm and 25–38 cm and separated into particle-size fractions. Each fraction was analyzed by Py–GC/AED at 300, 400 and 500 °C consecutively. The main N-structures found in pyrolysates were ammonia, acetonitrile, hydrogen cyanide, pyridine and pyrrole. Ratios of acetonitrile and hydrogen cyanide to pyridine and pyrrole decreased with soil depth. Acetonitrile and hydrogen cyanide had positive correlations with total organic N (TON) down the soil profile. A decrease of the optimal pyrolysis temperatures of soil samples with increasing soil depth was observed for acetonitrile and hydrogen cyanide. In the surface soil samples, there was no correlation found for both pyridine and pyrrole with TON. But with depth, the correlation coefficient increased and reached to 0.912 for pyridine, and 0.875 for pyrrole at the depth of 25–38 cm. The increased correlation coefficients of pyridine and pyrrole with TON in combination with the low shifts of the optimal pyrolysis temperatures of the soil samples down the soil profile for acetonitrile and hydrogen cyanide indicated clear differences in N-structures between different soil layers.     

Chemical analysis of industrial scale deposits by combined use of correlation coefficients with emission line detection of laser induced breakdown spectroscopy spectra

Laser-induced breakdown spectroscopy (LIBS) was used to determine the mineral composition of various industrial scale samples. The aim of the study has been to investigate the capacity of LIBS to provide a fast, reliable analytical tool for carrying out routine analysis of inorganic scales, potentially on site, as a means to facilitate decision making concerning scale removal procedures. LIBS spectra collected in the range of 200–660 nm conveyed information about the metal content of the minerals. Via a straightforward analysis based on linear correlation of LIBS spectra it was possible to successfully discriminate scale samples into three main groups, Fe-rich, Ca-rich and Ba-rich, on the basis of correlation coefficients. By combining correlation coefficients with spectral data collected in the NIR, 860–960 nm, where sulfur emissions are detected, it became further possible to discriminate sulfates from carbonates as confirmed by independent analysis based on Raman spectroscopy. It is emphasized that the proposed LIBS-based method successfully identifies the major mineral or minerals present in the samples classifying the scales into relevant groups hence enabling process engineers to select appropriate scale dissolution strategies.     

Role of laser pre-pulse wavelength and inter-pulse delay on signal enhancement in collinear double-pulse laser-induced breakdown spectroscopy

Dual-pulse (DP) laser-induced breakdown spectroscopy (LIBS) provides significant improvement in signal intensity as compared to conventional single-pulse LIBS. We investigated collinear DPLIBS experimental performance using various laser wavelength combinations employing 1064 nm, 532 nm, and 266 nm Nd:YAG lasers. In particular, the role of the pre-pulse laser wavelength, inter-pulse delay times, and energies of the reheating pulses on LIBS sensitivity improvements is studied. Wavelengths of 1064 nm, 532 nm, and 266 nm pulses were used for generating pre-pulse plasma while 1064 nm pulse was used for reheating the pre-formed plasma generated by the pre-pulse. Significant emission intensity enhancement is noticed for all reheated plasma regardless of the pre-pulse excitation beam wavelength compared to single pulse LIBS. A dual peak in signal enhancement was observed for different inter-pulse delays, especially for 1064:1064 nm combinations, which is explained based on temperature measurement and shockwave expansion phenomenon. Our results also show that 266 nm:1064 nm combination provided maximum absolute signal intensity as compared to 1064 nm:1064 nm or 532 nm:1064 nm.     

Assessment of soil quality of arable soils in Hungary using DRIFT spectroscopy and chemometrics

Nowadays, there is a great demand for precise, sensitive and adequate indicators for evaluating the quality of soils. In spite of recent developments in this field, a fast, non-destructive method for soil quality assessment has not yet been evaluated. The objective of this study was to investigate the possibility of using diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy to estimate soil quality in the form of soil quality index (SQI). A set of soil samples (n = 89) was scanned and regression was carried out using a combination of DRIFT spectroscopy and partial least-squares (PLS). The reliability of the DRIFT-PLS calibration model (n = 53) was acceptable (coefficient of determination, R² = 0.49; residual prediction deviation, RPD = 1.4) for the estimating of the SQI values. The validation of the calibration model using a validation set (n = 36) of unknown samples also resulted in good acceptability with R² = 0.68 and RPD = 1.85. The DRIFT-PLS based model could provide a rapid, cheap estimate of SQI values and subsequently of soil quality by taking into account the integrated effects of the mineralogical and organic components of the soil. This approach could be useful to monitor soil quality under conditions where the analysis of a large number of soil samples is required.     

Influence of sample temperature on the expansion dynamics and the optical emission of laser-induced plasma

We investigate the influence of sample temperature on the dynamics and optical emission of laser induced plasma for various solid materials. Bulk aluminum alloy, silicon wafer, and metallurgical slag samples are heated to temperature T_S ≤ 500 °C and ablated in air by Nd:YAG laser pulses (wavelength 1064 nm, pulse duration approx. 7 ns). The plasma dynamics is investigated by fast time-resolved photography. For laser-induced breakdown spectroscopy (LIBS) the optical emission of plasma is measured by Echelle spectrometers in combination with intensified CCD cameras. For all sample materials the temporal evolution of plume size and broadband plasma emission vary systematically with T_S. The size and brightness of expanding plumes increase at higher T_S while the mean intensity remains independent of temperature. The intensity of emission lines increases with temperature for all samples. Plasma temperature and electron number density do not vary with T_S. We apply the calibration-free LIBS method to determine the concentration of major oxides in slag and find good agreement to reference data up to T_S = 450 °C. The LIBS analysis of multi-component materials at high temperature is of interest for technical applications, e.g. in industrial production processes.     

Quality variations of poultry litter biochar generated at different pyrolysis temperatures

Producing biochar and biofuels from poultry litter (PL) through slow pyrolysis is a farm-based, value-added approach to recycle the organic waste. Experiments were conducted to examine the effect of pyrolysis temperature on the quality PL biochar and to identify the optimal pyrolysis temperature for converting PL to agricultural-use biochar. As peak pyrolysis temperature increased incrementally from 300 to 600 °C, biochar yield, total N content, organic carbon (OC) content, and cation exchange capacity (CEC) decreased while pH, ash content, OC stability, and BET surface area increased. The generated biochars showed yields 45.7–60.1% of feed mass, OC 325–380 g kg⁻¹, pH 9.5–11.5, BET surface area 2.0–3.2 m² g⁻¹, and CEC 21.6–36.3 cmol_c kg⁻¹. The maximal transformation of feed OC into biochar recalcitrant OC occurred at 500 °C, yet 81.2% of the feed N was lost in volatiles at this temperature. To produce agricultural-use PL biochar, 300 °C should be selected in pyrolysis; for carbon sequestration and other environmental applications, 500 °C is recommended.     

Quantitative analysis of samples at high temperature with remote laser-induced breakdown spectrometry using a room-temperature calibration plot

A method for measurement of composition in samples at high temperature using a calibration curve performed at low temperature is presented. The method uses a transfer function which avoids the need for building a calibration plot at high temperature. The method has shown suitability for high-temperature measurements up to 850 °C in steel slags exhibiting coefficients of correlation of 0.991 and 0.989 for Si / Ca and Mg / Ca ratios, respectively. The accuracy of the method has been assessed by comparing the results with remote LIBS at high temperature to those by XRF at room temperature. As an example of its versatility, the method has been applied to the determination of the basicity index of steel slags at high temperature.     

Femtosecond and nanosecond laser induced breakdown spectroscopic studies of NTO,HMX, and RDX

We present our results from the laser induced breakdown spectroscopic studies of 5-Nitro-2,4-dihydro-3H-1,2,4-triazol-3-one (NTO), Octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), and 1,3,5-Trinitroperhydro-1,3,5-triazine (RDX) investigated using nanosecond and femtosecond pulses. The presence of C, CN peaks in the spectra, signatures of high energy materials, was confirmed and persistence of emissions has been measured. Some of the Nitrogen peaks in fs LIBS spectra were found to be lower in magnitude (after normalization with N 868.60 nm peak) compared to the ns LIBS spectra. The presence of an additional CN peak in the fs spectra was identified for all samples. The ratio of CN peaks (388.28 nm, 387.08 nm, 386.16 nm) to C peak (247.82 nm), recorded with similar fluences, was discovered to be stronger in the fs case. Some of the possible mechanisms ensuing from our studies towards discrimination of such materials are outlined.     

High oxygen-reduction activity of silk-derived activated carbon

Activated carbon prepared from silk fibroin, which is free of metal elements, showed a high catalytic activity for the oxygen-reduction reaction (ORR). The activated carbon had a very high onset potential of E_onset = 0.83 V (vs. RHE) in oxygen-saturated 0.5 M H₂SO₄ at 60 °C. The ORR on the activated carbon proceeded by a four-electron process in the high-electrode-potential region; this gradually decreased to a 3.5-electron reaction below about 0.6 V (vs. RHE). Only about 1% of nitrogen atoms (mostly quaternary) remained in the activated carbon by heat-treatment at up to 1200 °C are responsible for the high catalytic activity. The open circuit voltage of a polymer electrolyte fuel cell using the activated carbon as the cathode and a platinum/carbon black anode under pure oxygen and hydrogen gases, respectively, both at one atmosphere, was 0.96 V at 27 °C.     

Effects of low-molecular-weight organic ligands and phosphate on adsorption of Pseudomonas putida by clay minerals and iron oxide

Adsorption of Pseudomonas putida on kaolinite, montmorillonite and goethite was studied in the presence of organic ligands and phosphate. Citrate, tartrate, oxalate and phosphate showed inhibitive effect on P. putida adsorption by three minerals in a broad range of anion concentrations. The highest efficiencies of the four ligands in blocking the adsorption of P. putida on goethite, kaolinite and montmorillonite were 58–90%, 35–76% and 20–48%, respectively. The ability of organic ligands in prohibiting the binding of P. putida cells to the minerals followed the sequence of citrate > tartrate > oxalate > acetate. The significant suppressive effects on P. putida adsorption were ascribed to the increased negative charges by adsorbed ligands and the competition of ligands with bacterial surface groups for binding sites. The inhibitive effects on P. putida adsorption by organic ligands were also dependent on the steric hindrance of the molecules. Acetate presented promotive effect on P. putida adsorption by kaolinite and goethite at low anion concentrations. The results obtained in this study suggested that the adsorption of bacteria in soils especially in the rhizosphere can significantly be impacted by various organic and inorganic anions.     

Design and development of a low cost,high performance UV digester prototype: Application to the determination of trace elements by stripping voltammetry

A low cost, high performance ultraviolet digester was developed and tested in our laboratory. Its main features include limited costs (around 600 € for all the parts) and high efficiency toward total organic carbon (TOC) abatement. As a result the TOC of typical natural waters is reduced to less than 10% of its initial value with half an hour treatment. Easiness of use, temperature control and flexibility in sample size (up to 25 mL) and number (up to twelve 12 mL test tube) are other important characteristics of the developed UV digester.This apparatus was tested as a pretreatment method for the determination of the total content of trace elements such as copper, uranium and platinum in natural waters by cathodic adsorptive stripping voltammetry. The voltammetric technique was chosen because it is strongly interfered by the presence of even low levels of natural organic complexing molecules. As a result, a 30 minute UV treatment yielded results non distinguishable from ICP-MS data.     

Determination of inorganic and total mercury by vapor generation atomic absorption spectrometry using different temperatures of the measurement cell

A simple and inexpensive laboratory-built flow injection vapor generation system coupled to atomic absorption spectrometry (FI-VG AAS) for inorganic and total mercury determination has been developed. It is based on the vapor generation of total mercury and a selective detection of Hg^2 + or total mercury by varying the temperature of the measurement cell. Only the inorganic mercury is measured when the quartz cell is at room temperature, and when the cell is heated to 650 °C or higher the total Hg concentration is measured. The organic Hg concentration in the sample is calculated from the difference between the total Hg and Hg^2 + concentrations. Parameters such as the type of acid (HCl or HNO₃) and its concentration, reductant (NaBH₄) concentration, carrier solution (HCl) flow rate, carrier gas flow rate, sample volume and quartz cell temperature, which influence FI-VG AAS system performance, were systematically investigated. The optimized conditions for Hg^2 + and total Hg determinations were: 1.0 mol l^− 1 HCl as carrier solution, carrier flow rate of 3.5 ml min^− 1, 0.1% (m/v) NaBH₄, reductant flow rate of 1.0 ml min^− 1 and carrier gas flow rate of 200 ml min^− 1. The relative standard deviation (RSD) is lower than 5.0% for a 1.0 μg l^− 1 Hg solution and the limit of quantification (LOQ, 10 s) is 55 ng g^− 1. Certified samples of dogfish muscle (DORM-1 and DORM-2) and non-certified fish samples were analyzed, using a 6.0 mol l^− 1 HCl solution for analyte extraction. The Hg^2 + and CH₃Hg⁺ concentrations found were in agreement with certified ones.     

Heavy elements concentrations,physiochemical characteristics and natural radionuclides levels along the Saudi coastline of the Gulf of Aqaba

This paper represents the first work on the concentrations of heavy elements, physiochemical characteristics and activity levels of the naturally occurring radionuclides in the Saudi Arabian coastline of the Gulf of Aqaba. Concentrations of 19 heavy elements were measured, namely: Ag, Al, As, Ba, Be, Cd, Co, Cr, Cu, Fe, Hg, Mn, Mo, Ni, Pb, Sb, Se, V and Zn. The radioactivity levels of ²³⁸U, ²³²Th and ⁴⁰K were estimated to be: 17 ± 1.7, 22.5 ± 3.7 and 649.6 ± 64.2 Bq kg^?1, respectively. The measurements were carried out using inductively coupled plasma-mass spectrometry (ICP-MS). In addition, physiochemical characteristics of 19 sediment samples (i.e., saturation percentage, pH, electrical conductivity, organic matter, cation exchange capacity and content of clay, silt and sand) have been determined. Indications for high correlation between most heavy elements are found. The correlation between heavy elements and the radionuclides ²³⁸U, ²³²Th and ⁴⁰K was generally significant.     

Thermal decomposition pathway of undoped and doped zinc layered gallate nanohybrid with Fe3+, Co2+ and Ni2+ to produce mesoporous and high pore volume carbon material

A series of brucite-like materials, undoped and doped zinc layered hydroxide nitrate with 2% (molar) Fe³⁺, Co²⁺ and Ni²⁺ were synthesized. Organic–inorganic nanohybrid material with gallate anion as a guest, and zinc hydroxide nitrate, as an inorganic layered host was prepared by the ion-exchange method. The nanohybrid materials were heat-treated at various temperatures, 400–700 °C. X-ray diffraction, thermal analysis and also Fourier transform infrared results showed that incorporation of the doping agents within the zinc layered hydroxide salt layers has enhanced the heat-resistivity of the nanohybrid materials in the thermal decomposition pathway. Porous carbon materials can be obtained from the heat-treating the nanohybrids at 600 and 700 °C. Calcination of the nanohybrids at 700 °C under nitrogen atmosphere produces mesoporous and high pore volume carbon materials.     

High-Temperature Liquid Chromatography Inductively Coupled Plasma Atomic Emission Spectrometry hyphenation for the combined organic and inorganic analysis of foodstuffs

The coupling of a High-Temperature Liquid Chromatography system (HTLC) with an Inductively Coupled Plasma Atomic Emission Spectrometer (ICP-AES) is reported for the first time. This hyphenation combines the separation efficiency of HTLC with the detection power of a simultaneous ICP-AES system and allows the combined determination of organic compound and metals. The effluents of the column were introduced into the spectrometer and the chromatograms for organic compounds were obtained by plotting the carbon emission signal at a characteristic wavelength versus time. As regards metals, they were determined by injecting a small sample volume between the exit of the column and the spectrometer and taking the emission intensity for each one of the elements simultaneously. Provided that in HTLC the effluents emerged at high temperatures, an aerosol was easily generated at the exit of the column. Therefore, the use of a pneumatic nebulizer as a component of a liquid sample introduction system in the ICP-AES could be avoided, thus reducing the peak dispersion and limits of detection by a factor of two. The fact that a hot liquid stream was nebulized made it necessary to use a thermostated spray chamber so as to avoid the plasma cooling as a cause of the excessive mass of solvent delivered to it. Due to the similarity in sample introduction, an Evaporative Light Scattering Detector (ELSD) was taken as a reference. Comparatively speaking, limits of detection were of the same order for both HTLC–ICP-AES and HTLC–ELSD, although the latter provided better results for some compounds (from 10 to 20 mg L^?1 and 5–10 mg L^?1, respectively). In contrast, the dynamic range for the new hyphenation was about two orders of magnitude wider. More importantly, HTLC–ICP-AES provided information about the content of both organic (glucose, sucrose, maltose and lactose at concentrations from roughly 10 to 400 mg L^?1) as well as inorganic (magnesium, calcium, sodium, zinc, potassium and boron at levels included within the 6–3000 mg L^?1) species. The new development was applied to the analysis of several food samples such as milk, cream, candy, isotonic beverage and beer. Good correlation was found between the data obtained for the two detectors used (i.e., ICP-AES and ELSD).     

Towards a two-dimensional laser induced breakdown spectroscopy mapping of liquefied petroleum gas and electrolytic oxy-hydrogen flames

Two-dimensional mapping of the laser-induced breakdown spectroscopy (LIBS) signal of chemical species information in liquefied petroleum gas (LPG) and electrolytic oxy-hydrogen (EOH) flames was performed with in situ flame diagnostics. Base LIBS signals averaged from measurements at wavelengths of 320 nm to 350 nm describe the density information of a flame. The CN LIBS signal provides the concentration of fuel, while the H/O signal represents the fuel/air equivalence ratio. Here, we demonstrate the meaningful use of two-dimensional LIBS mappings to provide key combustion information, such as density, fuel concentration, and fuel/air equivalence ratio.     

Preparation of activated carbon from Turbinaria turbinata seaweeds and its use as supercapacitor electrode materials

Turbinaria turbinata brown seaweeds were tested as carbon electrode material in symmetric, electrochemical supercapacitors. The electrochemical properties of the carbon materials were characterised for their application as supercapacitors using cyclic voltammetry, galvanostatic charge/discharge method and electrochemical impedance spectroscopic analyses. Our initial results showed that the optimal behaviour was obtained for the sample prepared by pyrolysis at 800 °C. The average surface area of the carbon was 812 m²/g. Electrochemical tests with an organic electrolyte gave the following interesting results: a capacitance of 74.5 F/g, a specific series resistance of 0.5 Ω cm² and an ionic resistivity of 1.3 Ω cm². These results show the promising capacitive properties of carbon derived from seaweeds and their application in electrochemical supercapacitors.