Random distributed feedback fiber laser pumped by an ytterbium doped fiber laser

A random distributed feedback fiber laser operating at 1115 nm has been demonstrated experimentally in standard communication optical fibers by using a LD-pumped Yb-doped fiber laser as the pump source. We have studied the effect of different fiber spans on this new type of random fiber laser output power. It is shown that the generation power is the highest up to 198 mW in a 50 km fiber span. The slope efficiency is more than 28.7%. Stable, high-power continuous-wave (CW) lasing can be generated when the pump power is 3.6 W. The threshold power has also been calculated which well proves a random fiber laser operating via Rayleigh scattering, amplified through the Raman scattering.     

Random fiber laser of POSS solution-filled hollow optical fiber by end pumping

Random fiber laser is obtained by end pumping a hollow optical fiber (HOF) filled with a dispersive solution of polyhedral oligomeric silsesquioxanes (POSS) nanoparticles and laser dye pyrromethene 597 (PM597) in carbon disulfide (CS₂), in which the concentration is 1.5×10^?2 M for PM597 and 18.5 wt% for POSS, respectively. It is found that the pump light at the one end of the liquid core optical fiber (LCOF) can pass the whole length of LCOF because the POSS nanoparticles were dispersed in CS₂ at a molecular level (1–3 nm) with high stability and without sedimentation. Above the threshold pump energy (～0.81 mJ) the random fiber laser appears coherent and resonant feedback multimode lasing in the weakly scattering system. For the LCOF containing PM597 with the same concentration and no POSS nanoparticles, there occurs only ASE that can be observed under the same experimental condition.     

Random Bragg-grating-based wavelength-tunable random fiber laser with a full-open cavity

A full-open-cavity wavelength-tunable random fiber laser(WT-RFL) with compact structure and hundreds of picometers tuning range is proposed and demonstrated. A π fiber Bragg grating(FBG) is used in the WT-RFL as a filter to select lasing wavelengths. The two random Bragg grating arrays(RBGAs) and a section of high gain erbium-doped fiber result in a low lasing threshold and high stability. A numerical model to analyze the tunable characteristics is developed. The results show that the laser threshold is 22 m W, and the maximum peak-power fluctuation is 0.55 d B. To the best of our knowledge, it is the first time that a compact and full-open-cavity WT-RFL with two RBGAs and a π-FBG is proposed.     

激光散斑与随机激光器件制作

提出了一种基于大学物理实验教学中激光散斑的随机激光器件的制作,分析了随机激光的分类标准和产生机理,系统考察了不同泵浦条件下该激光器件的输出特性.该实验方案为大学物理实验提供了与科技前沿接轨的素材.     

Side-pumped fiber laser

A neodymium-doped side-pumped double-clad fiber laser operating at 1.06 µm is described. We report here, what is, to our knowledge, the first exclusively repetitive side-pumping scheme with two monomode laser diodes. Side-pumping has been realized by prism-fiber couplers. A pump-light-loss analysis at the pump positions has been performed. An output power of 13.5 mW is obtained with both diode lasers. The highest slope efficiency of 66% with respect to absorbed pump power at 809 nm is achieved when pumping with only one diode.     

Random laser action in ZnO

We report a direct evidence of random laser in optically pumped ZnO powder. Discrete lasing modes are observed above threshold. The laser emission spectra depend on the angle of observation and are random. The lasing action is attributed to the coherent feedback due to recurrent light scattering in the powder. The lasing threshold intensity depends on the excitation volume. Received: 15 September 1999 / Revised version: 2 February 2000 / Published online: 5 July 2000     

Random period arc-induced long-period fiber gratings

We report the fabrication of arc-induced long-period fiber gratings with strong random variations in the period. Long-period fiber gratings with standard deviations in the period from 8.50 to 36.98 μm were fabricated. The spectral position of the resonant bands is determined by the average period value, being similar to that observed in a long-period fiber grating with a fixed period equal to the average period of the random grating. Moreover the notch bands keep the shape characteristics like wideband and depth compared with a long-period grating with a constant period. In addition, their sensitivity to external parameters such as ambient refractive index is not too different with that of fixed period long-period gratings.     

Random laser in one dimension

We present an analytical approach to random lasing in a one-dimensional medium, consistent with transfer matrix numerical simulations. It is demonstrated that the lasing threshold is defined by transmission through the passive medium and thus depends exponentially on the size of the system. Lasing in the most efficient regime of strong three-dimensional localization of light is discussed. We argue that the lasing threshold should have anomalously strong fluctuations from probe to probe, in agreement with recent measurements.     

Modulational-instability sigma-resonator fiber laser

A modulational-instability laser with a resonator in a sigma configuration has been developed. The importance of a suitable intracavity filter for removing the autocorrelation background of the output signal is shown. A pulse train with a repetition rate of 107 GHz determined by the Fabry-Perot etalon used in the resonator was obtained at 1.56mum .     

Microstructured polymer fiber laser

A microstructured polymer optical fiber doped with Rhodamine 6G dye was fabricated and demonstrated as an optical amplifier and a fiber laser. As an amplifier, the fiber achieved a gain in excess of 30 dB. As a pulsed fiber laser, the fiber exhibited a threshold of 20 microJ, a slope efficiency of 18%, and a lifetime as high as 130,000 shots at 10 Hz. The maximum output energy was 16 microJ. The advantages that such fibers offer lie in the simplicity and flexibility of their fabrication and in their potential for use as compact, tunable solid-state sources.     

High-power photonic-bandgap fiber laser

An original architecture of an active fiber allowing a nearly diffraction-limited beam to be produced is demonstrated. The active medium is a double-clad large-mode-area photonic-bandgap fiber consisting of a 10,000 ppm by weight Yb(3+)-doped core surrounded by an alternation of high- and low-index layers constituting a cylindrical photonic crystal. The periodic cladding allows the robust propagation of a approximately 200 microm(2) fundamental mode and efficiently discriminates against the high-order modes. The M(2) parameter was measured to be 1.17. A high-power cw laser was built exhibiting 80% slope efficiency above threshold. The robust propagation allows the fiber to be tightly bent. Weak incidence on the slope efficiency was observed with wounding radii as small as 6 cm.     

All-fiber mode-locked fiber laser

An environmentally stable mode-locked fiber laser based on nonlinear polarization rotation is experimentally demonstrated. The laser is based on a novel laser configuration that has negligible low-power steady-state reflectivity from one side and, consequently, no CW gain. The laser is self starting and the configuration is implementable as an all-fiber laser with standard polarization-maintaining fiber-pigtailed components. A pulse duration of 5.6 ps is obtained at a repetition rate of 5.96 MHz and at an average power of 8 mW. As an application of the proposed laser configuration, 213 mW of supercontinuum (600-1750 nm) was demonstrated from a fiber laser system with no sections of free-space optics.     

Ultrahigh-repetition-rate bound-soliton fiber laser

Ultrahigh-repetition-rate (over 100 GHz) bound-soliton pulses were experimentally generated in a fiber laser. Through incorporating a Loyt-type filter made of a piece of high birefringent fiber and an intracavity polarizer in a fiber laser, we found that not only ultrahigh-repetition-rate single-pulse soliton but also bound-soliton trains could be generated. Numerical simulations confirm the experimental observations.     

Self-polarized ytterbium-doped fiber laser

We demonstrate a linearly-polarized, ytterbium-doped fiber laser that uses an uncoated, undoped ceramic YAG plate as the output coupler, and the corresponding polarization extinction ratio of laser beam increases with incident pump power and then saturates at larger pump power. For comparison, the output coupler of the fiber laser is replaced by 10% reflectivity plane mirror, while the feature of the polarization of laser output is kept unchanged. The results show that the origin of the pump-dependent and self-started polarization is associated with the intensity-dependent nonlinear birefringence in the gain fiber.     

光纤陀螺随机游走分析方法研究

 光纤陀螺测试中,随机游走系数的分析对陀螺整体性能的评价起着很重要的作用。分别介绍了分析光纤陀螺随机游走噪声的两种方法：Allan方差法和改进的Allan方差法。分别应用这两种方法,在对某型光纤陀螺(FOG)实测静态数据计算的基础上进一步分析了该光纤陀螺中的噪声分量,并对分析结果进行比较。最终计算结果表明：在增加计算时间为代价的前提下,改进Allan方差法能方便地区别出各种噪声,并明显提高了光纤陀螺各随机噪声游走系数的计算精度。     

Three-level neodymium fiber laser incorporating photonic bandgap fiber

We report a neodymium fiber laser incorporating an all-solid photonic bandgap fiber to suppress the four-level laser transition 4F(3/2)-4I(11/2). We demonstrate lasing at 907 nm on the three-level transition 4F(3/2)-4I(9/2) when pumping at 808 nm. The maximum slope efficiency obtained was 32% with a threshold pump power of 70 mW.     

Random laser action in bovine semen

Experiments using bovine semen reveal that the addition of a high-gain water soluble dye results in random laser action when excited by a Q-switched, frequency doubled, Nd:Yag laser. The data shows that the linewidth collapse of the emission is correlated to the sperm count of the individual samples, potentially making this a rapid, low sample volume approach to count determination.     

基于飞秒激光直写光纤光栅的掺镱光纤激光器

 利用飞秒激光微加工技术,可以在光纤纤芯内直写出布拉格光栅,它与传统的光纤光栅制作方法相比,具有耗时短、无需光敏光纤、周期可任意设定、光栅稳定性高等优点。采用800 nm钛宝石飞秒激光器,在Hi1060光纤内写入一支8 mm长的布拉格光栅,光纤光栅的周期为2.9 μm,这是中心波长为1 042 nm的八阶光纤布拉格光栅。将所得光栅与一段有源的双包层光纤熔接,作为激光输出镜,利用975 nm的LD光纤模块作为泵浦源,采用端泵浦技术构成双包层光纤激光器。双包层光纤采用Nufern公司镱(Yb³⁺)离子掺杂双包层光纤,光纤长度3 m。所得激光器的输出功率为71.1 W,中心波长1 042 nm,带宽约为0.8 nm。     

基于飞秒激光直写光纤光栅的掺镱光纤激光器

利用飞秒激光微加工技术,可以在光纤纤芯内直写出布拉格光栅,它与传统的光纤光栅制作方法相比,具有耗时短、无需光敏光纤、周期可任意设定、光栅稳定性高等优点。采用800 nm钛宝石飞秒激光器,在Hi1060光纤内写入一支8 mm长的布拉格光栅,光纤光栅的周期为2.9 μm,这是中心波长为1 042 nm的八阶光纤布拉格光栅。将所得光栅与一段有源的双包层光纤熔接,作为激光输出镜,利用975 nm的LD光纤模块作为泵浦源,采用端泵浦技术构成双包层光纤激光器。双包层光纤采用Nufern公司镱(Yb3+)离子掺杂双包层光纤,光纤长度3 m。所得激光器的输出功率为71.1 W,中心波长1 042 nm,带宽约为0.8 nm。     

A self-seeded fiber laser incorporated with a fiber Bragg grating external cavity semiconductor laser

A self-seeded fiber laser incorporated with a fiber Bragg grating external cavity semiconductor laser (FBG-ECL) and a Mach-Zehnder interferometer (MZI) were reported in this paper. The MZI provided a Q-switching with response time in the order of micro-seconds. The FBG-ECL provided narrow pulses as seeds to shorten the Q-switched pulses. Experimentally, pulse width of 0.8 μs was measured, which was one fifth of the pulse width without self-seeding.