铂修饰光阴极及其在纳晶太阳能电池中的应用

分别用真空镀膜法、热分解法和电化学法制备了铂金修饰导电玻璃,并以此作为光阴极组装了染料敏化纳晶TiO₂太阳能电池.用SEM观察了铂金修饰导电玻璃表面形貌,发现用真空镀膜法制备的铂金膜结构缺陷多、不均匀,存在较多的污点.用热分解法制备的铂金膜具有多孔状结构,但存在较多的有机物分解的残留物.用电镀法制备的铂金膜结构均匀、排列规则、缺陷少、污染少.测定了所制备铂金膜的电阻,结果表明由电镀法所制得的铂金膜电阻最小,用热解法和真空镀膜法制得的铂金膜电阻较大.测定了DSSC电池的光电性能,发现用电镀法制得的铂金膜的催化性能最好,大大提高了DSSC电池的性能;其次是热分解法,由真空镀膜法制备的铂金膜对电池的性能没有多大改善.     

Comparison of NAA and ICP-MS for the determination of major and trace elements in environmental sample

Summary Major and trace elements in soil and plant samples, including standard reference materials were determined by means of neutron activation analysis (NAA) and inductively coupled plasma-mass spectrometry (ICP-MS). The analytical procedure for NAA utilized dried powder samples. The concentration of iodine in soil samples was determined by radiochemical NAA. The irradiated samples were cooled and then counted with a Ge gamma-ray detector connected to a multi-channel analyzer. For ICP-MS analysis, the samples were decomposed by microwave digestion with an acid mixture. The concentration of I in the soil samples was measured by ICP-MS after separation by ignition. The analytical values for most elements in the environmental samples by both methods were in good agreement, whereas sample treatments were different. Measured value of Zr in the soil samples by ICP-MS was about 50% lower than that by NAA. It should be assumed that some minerals of Zr in soil particles were not entirely dissolved by the acid mixture. Analytical results of Cd for three different Cd levels in unpolished rice flour samples (NIES 10-a, b and c) determined by ICP-MS were in agreement with certified values. The concentration of Cd in the sample with the lowest Cd level, as determined by NAA with 57% counting error, was 3 times higher than the certified value.     

锰离子控制掺杂二氧化钛薄膜光催化活性增强的机理探讨

采用溶胶-凝胶法通过工艺控制制备了锰离子以不同形式掺杂TiO₂的光催化剂薄膜,并通过XPS和SEM对薄膜的结构进行表征.通过UV-Vis分光光度计及电化学工作站表征了薄膜的光吸收性能和光电化学性能,通过甲基橙溶液的光催化降解脱色率来表征催化剂薄膜的光催化活性.结果表明,以锰离子MT掺杂方式制备的TiO₂薄膜可明显增强TiO₂的光催化活性,而以MM掺杂方式制备的TiO₂薄膜反而降低了TiO₂的光催化活性;锰离子MT掺杂方式的最佳掺杂质量分数为0.8%.催化剂薄膜的电化学行为显示,薄膜具有p-n结的电容-电压特性,锰离子MT掺杂TiO₂薄膜的开路电位和瞬时光电流信号较强,说明其光生载流子易于生成并且分离效果较好.依据半导体的p-n结原理探讨了锰离子控制掺杂TiO₂的光催化活性机理.     

方波伏安法评估聚苯胺膜修饰电极的电荷传输速度

研究导电聚合物的电荷传输机制与速度对于其在应用方面的研究极为重要［‘］．例如在电池的研究中，充放电的速度决定于导电聚合物的电荷传输速度；在电致变色器件的研究中，响应时间也是决定于导电聚合物在氧化还原态间的变化速度，即电荷传输速度．显然较低的电荷传输速度不利于器件的实用化，因此人们必须找到一种能够迅速准确评价电荷传输速度的方法，由于导电聚合物是一个特殊的体系，用一般的电化学方法对其电荷传输速度进行测定时常常遇到这样或那样的问题［‘j．一般说来，导电聚合物的氧化还原过程中均伴随着抗衡离子的运动．体系…     

Nitration and amination of polyphenylene oxide: Synthesis, gas sorption and permeation analysis

A high degree of nitration of polyphenylene oxide (PPO) was successfully achieved by carefully optimizing synthetic protocol. The reduction of nitro group to amino could be done quantitatively. The physical properties of formed polymers were investigated and correlated with gas sorption and permeation properties. The formed polymers were amorphous in nature as revealed by wide angle X-ray diffraction spectra. An increase in the packing density in comparison to unsubstituted PPO as a result of induced polarity was indicated by lowering of fractional free volume and d-spacing. The substitution by either nitro or amino group increased the chain stiffness as revealed by the dynamic mechanical analysis. Though both, nitro and amino group substitution on PPO led to a decrease in pure gas permeability, the selectivity of various gas pairs was increased by these substitutions. The gas sorption analysis revealed that both, solubility selectivity and diffusivity selectivity were increased by these polar group substitutions. The nitro group substitution was more effective in improving solubility selectivity, while amino group substitution was more effective in improving diffusivity selectivity.     

Room temperature phosphorescence of 1-naphtalenacetamide included in beta-cyclodextrin in presence of 1,3-dibromopropane

The spectral characteristics of the inclusion of 1-naphthalenacetamide in beta-cyclodextrin have been studied by luminescence methods. The addition of bromoalcohols or bromoalkanes produces a decrease of the fluorescence of the inclusion complex, giving rise to a new band corresponding to phosphorescence emission. The emission intensity is much higher in the presence of bromoalkanes than in the presence of bromoalcohols. The deoxygenation of the solutions is achieved by flowing nitrogen, by the addition of sodium sulphite and by a combination of both methods, which results in the most effective approach. The phosphorescence emission is produced in the turbid suspension formed in the presence of the bromoalkane. The formation of microcrystals seems necessary to obtain phosphorescence emission from the ternary system.     

Synthesis and characterization of heat-stabilized albumin magnetic microspheres

Human serum albumin magnetic microspheres containing 30% iron oxide particles were synthesized by a heat-stabilization process. The average diameter, the size distribution and the morphology were characterized by scanning electron microscopy, atomic force microscopy and transmission electron microscopy. The distribution of the iron oxide nanoparticles within the microspheres was confirmed by the contrast obtained in the morphology by backscattered electron imaging in scanning electron microscopy. Energy-dispersive X-ray spectroscopy showed the presence of iron in the microspheres. The cabbage like surface structure in some of the microspheres obtained in scanning electron microscopy can be better understood by atomic force microscopy. This peculiar surface structure in the microsphere may be due to the cross-linking in the protein molecule by heat. The amount of iron oxide in the microsphere was analyzed by atomic absorption spectroscopy. The magnetic properties of the particles were measured in a superconducting quantum interference device magnetometer. Received: 12 September 2000 Accepted: 5 February 2001     

Nd—Al双金属活性体对异戊二烯的溶液聚合

近年来,对于稀土Ziegler-Natta催化剂活性体的研究比较活跃。使用催化剂活性体可以消除剩余烷基铝等因素对聚合反应的影响,比以前所用的多组分混合物的催化体系更客观地反映出聚合过程。我们在以前工作的基础上,从体系中分离出Nd-Al双金属活性体,并用于引发异戊二烯溶液聚合,探讨不同聚合条件下异戊二烯溶液聚合的规律,以利于对稀土催化聚合反应的深入了解。     

CdS纳米粒子的表面修饰及其对光学性质的影响

用反胶束法合成了用表面活性剂分子磺基焉珀酸双－２－乙基已酯钠盐（ＡＯＴ）进行表面修饰的ＣｄＳ纳米粒子（记为ＣｄＳ／ＡＯＴ－ＳＯ３＾－）,研究了这种纳米粒子在正庚烷（ｈｅｐｔａｅ）和吡啶（Ｐｙ）溶剂中的荧肖及光解行为,发现其在正庚烷中荧光很强,而Ｐｙ却强烈地猝灭ＣｄＳ纳一子的荧光,用电荷转移猝灭机制进行了解释,这种解释为ＣｄＳ纳米粒子在Ｐｙ中光解实验进一步证实。     

Dependence of turbidity oscillations of self-oscillating polymers on the selective recognition of the crown ether receptors contained in the polymer chain

The turbidity oscillations of self-oscillating polymers in the Belousov-Zhabotinsky (BZ) reaction system depending on the crown ether receptors contained in the polymer network have been studied. The three monomers are copolymerized, namely, N-isopropylacrylamide, the metal catalyst monomer for the BZ reaction, and the crown ether receptor monomer, to prepare the self-oscillating polymers used in this study. The turbidity oscillations are characterized by monitoring the transmittance of the polymer solution in the BZ reaction system at a specific wavelength of 570 nm. The oscillations are varied by crown ether receptors used in the polymerization process, i.e., BCAm(6) or BCAm(5), for the selective recognition of specific cations between potassium and sodium ions in the solution. The selective recognition of the BCAm receptors in the polymer chain for the two ions has brought out a variation in the turbidity oscillations by a change in the hydrophilicity of the polymer chain. The oscillations of the polymer solution composed of the BCAm(5) receptor are more influenced by sodium ion, while the polymer solution of BCAm(6) receptor is affected by potassium ion. However, the oscillation patterns of the redox changes obtained by these solution systems look much alike despite the differences in the polymer chain by crown ether receptors and cations of bromate used for the BZ reaction.     

Dry deposition of elemental iodine on skin,hair, and clothing from air

Hairless rats, clothes, human hair, filter paper and water were exposed to gaseous elemental iodine in a glass chamber for 60–120 minutes. The deposition of gaseous elemental iodine on skin and lung of rats, human hair, water, clothes and paper were investigated by measuring iodine content in the exposed material by epithermal neutron activation analysis (ENAA). For measurement of the iodine concentration in the chamber air, elemental iodine in the air was collected by continuously sucking air through an active charcoal column. The trapped iodine in the active charcoal was then determined by ENAA. The measured deposition velocity in the test chamber of gaseous elemental iodine on skin, clothing, hair and water ranges from 0.006 on filter paper and water to about 0.05 cm/s on skin and clothes. The variation of elemental iodine concentration in air of the glass chamber was investigated by collecting and analyzing air samples at various time intervals. The results show that the variation with time in the concentration of the iodine can be described by an exponential function.     

Filler-elastomer interactions: influence of silane coupling agent on crosslink density and thermal stability of silica/rubber composites

In this work, the crosslink density and thermal stability of the silica/rubber composites treated by silane coupling agents, i.e., gamma-aminopropyl triethoxysilane (APS), gamma-chloropropyl trimethoxysilane (CPS), and gamma-methacryloxypropyl trimethoxysilane (MPS), were investigated. The chemical structures of modified silicas were studied in term of solid-state 29Si NMR spectroscopy. The crosslink density of the composites was determined by swelling measurement. The development of organic functional groups on silica surfaces treated by coupling agents led to an increase in the crosslink density of the composites, resulting in increasing final thermal stability of the composites. The composites treated by MPS showed the superior crosslink density and thermal stability in these systems. The results could be explained by the fact that the organic functional groups of silica surfaces by silane surface treatments led to an increase of the adhesion at interfaces between silicas and the rubber matrix.     

Über analytische Untersuchungen an magnetischen Materialien

The determination of metals in cubic ferrites is performed by volumetric analysis in the semi-microscale. The iron content is titrated cerimetrically. All other elements are determined by complexometric titration, partially after separation by ion-exchange methods. The separation of iron was achieved by ether and cupferron extraction. The errors of the determination amount up to 0.5% for iron, for other metals up to 1.0% or about 2% in the case of multicomponent systems.     

Precursor-directed assembly of complex oxide nanobeads: the role of strongly coordinated inorganic anions

The use of an inorganic perrhenate ligand in the structure of early-transition-metal alkoxide precursors permits to achieve uniform self-assembly of the primary nanoparticles produced by their hydrolysis. The latter has been carried out in a hydrocarbon reaction medium by the addition of water with vigorous stirring, either in the pure form or in solutions in parent alcohols. The self-assembly is guided by the surface charge enhanced by the presence of strongly coordinated anions as determined by zeta potential measurements. The aggregation process has been followed in real time by nanoparticle tracking analysis (NanoSight technique). The reaction products are spherical aggregates with a size that can be efficiently controlled through the polarity of the reaction medium. The produced nanobeads have been characterized by TEM, SEM-EDS, DLS, nitrogen adsorption, and FTIR. The coordination of metal centers has been investigated using EXAFS spectroscopy. The aggregates remain amorphous on thermal treatment of up to 700 °C (24 h treatment) but crystallize when treated at 1000 °C. This latter process is associated with the total loss of rhenium content and offers early-transition-metal oxides as products.     

Kinetics and mechanisms of the oxidation by permanganate of L-Phenylalanine

The oxidation of L-Phenylalanine by permanganate ion in aqueous phosphate buffers is autocatalized by the inorganic reaction product, which is stabilized in solution by adsorption of phosphate ions on its surface. This product is a soluble form of colloidal manganese dioxide. The rate of the noncatalytic reaction pathway is first-order in both the oxidizing and reducing agent. It is not affected by potassium chloride addition to the solution, but by phosphate addition. The rate increases with the pH of the medium. The autocatalytic pathway is first-order in both permanganate ion and colloidal manganese dioxide, (the permanganate ion according to the Langmuir isotherm). The autocatalytic rate increases with reductant concentration (follows the Langmuir adsorption isotherm). It is not affected by potassium chloride addition to the solution, whereas an increase in the phosphate concentration results in an increase in the rate with the same pH of the medium. Mechanisms consistent with the experimental data are proposed.     

Studies on α-, β-, and γ-cyclodextrin inclusion complexes of isoquinoline alkaloids berberine, palmatine and coralyne

The complexation of three isoquinoline alkaloids berberine, palmatine and coralyne with α-, β-, and γ-CDs were studied by absorption, fluorescence, circular dichroism, NMR spectroscopy and microcalorimetric assay techniques. Their binding constant (K _BH) values were determined by Benesi–Hildebrand equation. All the alkaloids formed 1:1 stoichiometry complexes with the cyclodextrins (CDs). The binding affinity is largest in β-CD followed by γ-, and α-CD for coralyne, followed by berberine and then palmatine. The thermodynamic parameters of the complexation were determined by calorimetry. The stoichiometry of complex formation and the variation of the apparent binding constant from spectroscopic studies were confirmed by calorimetry. The formation of the inclusion complexes was entropy driven in almost all the systems. Coralyne formed the strongest complex with all the CDs, followed by berberine and palmatine in that order. Coralyne-β-CD complex was studied through NMR, indicating more than one interaction mode.     

AUGMENTATION OF ULTRAVIOLET ERYTHEMA BY INDOMETHACIN IN ACTINIC PRURIGO: EVIDENCE OF MECHANISM OF PHOTOSENSITIVITY

Abstract— The effect of topical indomethacin on the intensity of erythema induced by ultraviolet radiation was measured by reflectance spectrophotometry in six patients with actinic prurigo. The intensity of UV-C erythema was decreased by indomethacin in five patients. The intensity of UV-B erythema was increased by indomethacin in five patients, and UV-A erythema was increased by indomethacin in all patients. The increased inflammatory response induced by UV-B and UV-A with indomethacin application was related to erythemal sensitivity at these wavelengths. Topical indomethacin caused no change in the intensity of UV-A erythema in a group of non-photosensitive subjects.
That inhibition of cyclo-oxygenase augments the inflammatory response to ultraviolet radiation suggests that lipoxygenase metabolites of arachidonic acid may be involved in the mechanism of photosensitivity in actinic prurigo.     

INVESTIGATION OF POLYDL-LACTIDE-b-POLY（ETHYLENE GLYCOL）-b-POLYDL-LACTIDE MICROSPHERES CONTAINING PLASMID DNA

PolyDL-lactide (PDLLA) and the block copolymer, polyDL-lactide-b-poly(ethylene glycol)-b-polyDL-lactide (PELA) were used as the microsphere matrix to encapsulate plasmid DNA. The PDLLA, PELA, pBR322-1oaded PDLLA and pBR322-1oaded PELA microspheres were prepared by solvent extraction method based on the formation of multiple w1/o/w2 emulsion. The microspheres were characterized by surface morphology, mean particle size, particle size distribution and loading efficiency. The integrity of DNA molecules after being extracted from microspheres was determined by agarose gel electrophoresis. The result suggested that plasmid DNA molecules could retain their integrity after being encapsulated by PELA. The PELA microspheres could prevent plasmid DNA from being digested by DNase. The in vitro degradation and release profiles of plasmid DNA-loaded microspheres were measured in pH - 7.4 buffer solution at 37℃. The in vitro degradation profiles of the microspheres were evaluated by the deterioration in microspheres surface morphology, the molecular weight reduction of polymer, the mass loss of microspheres, the changes of pH values of degradation medium, and the changes of particle size. The in vitro release profiles of the microspheres were assessed by measurement of the amount of DNA presented in the release medium at determined intervals. The release profiles were correlation with the degradation profiles. The release of plasmid DNA from PELA microspheres showed a similar biphasic trend, that is, an initial burst release was followed by a slow, but sustained release.     

Enzymatically synthesized polyaniline film deposition studied by simultaneous open circuit potential and electrochemical quartz crystal microbalance measurements

The chemical and enzymatic deposition of polyaniline (PANI) films by in situ polymerization was studied and the resulting films were characterized. The film formation and polymerization processes were simultaneously monitored by the evolution of the open circuit potential and quartz-crystal microbalance measurements. Different substrates, such as Indium-Tin oxide electrodes and gold-coated quartz-crystal electrodes were used as substrates for PANI deposition. Electroactive PANI films were successfully deposited by in situ enzymatic polymerization at low oxidation potential. The electrogravimetric response of the enzymatically deposited PANI film was studied by cyclic voltammetry in monomer-free acidic medium. The morphology of the films was observed by scanning electron microscopy, revealing a granular structure in enzymatically deposited PANI. The PANI films were also characterized by thermogravimetric analysis, electrochemical impedance spectroscopy, and X-ray photoelectron and Fourier-transformed infrared spectroscopy. The simultaneous use of quartz crystal microbalance and open circuit potential is presented as a very useful technique to monitor enzymatic reactions involving oxidoreductases.     

Atomization of Al in a tungsten coil electrothermal atomic absorption spectrophotometer

Electrothermal atomic absorption spectrophotometry of Al in a tungsten coil atomizer was evaluated and applied for its determination in hemodialysis fluid. The system was mounted on a Varian Spectra AA-40 spectrophotometer with continuum background correction and all measurements, in peak height absorbance, were done at 309.3 nm. The purge gas was a mixture of 90% Ar plus 10% H(2). Observation height, gas flow, drying, pyrolysis and atomization steps were optimized. The heating program was carried out by employing a heating cycle in four steps: dry, pyrolysis, atomization and clean. The determination of Al in hemodialysis solutions was performed by using a matrix-matching procedure. Al in hemodialysis solutions was determined by TCA and by electrothermal atomization with a graphite tube atomizer. There is no differences between results obtained by both methods at a confidence level of 95%. The characteristic mass of Al by using the TCA was 39 pg and the detection limit was 2.0 mug l(-1).