PREPARATION OF ACTIVATED CARBON FIBER AND THEIR XENON ADSORPTION PROPERTIES（Ⅱ）-XENON ADSORPTION PROPERTIES

The adsorption of xenon from air has an interest in the monitoring of nuclear explosion oraccident, or in the treatment of nuclear waste gas. In this paper, the pore structure of several series ofactivated carbon fibers has been characterized. The adsorption properties of xenon on theseactivated carbon fibers under different temperatures have been studied in details. The results showthat the xenon adsorption amount on activated carbon fibers do not increase with specific surfacearea of adsorbents, but are closely related to their pore size distribution. Pores whose radius equal toor narrow than 0.4nm would be more advantageous to the adsorption of xenon.     

活性碳纤维的结构修饰及其吸附氙性能的研究

活性炭纤维对氙的吸附容量与其孔结构密切相关，为了提高活性炭纤维对氙气的吸附容量，本文分别用亚甲基蓝、对硝基苯酚等有机物，或氯化钠、碘等无机化合物填充的方法修饰活性炭纤维的孔结构；以及利用高锰酸钾或硝酸等氧化处理修饰活性炭纤维的表面化学性质，同时，利用低温氮等温吸附表征了这些改性活性炭纤维的孔结构，以及通过光电子能谱表征了改性活性炭纤维的表面化学结构，上述化合物充填或氧化改性活性炭纤维对氙的吸附性能的研究结果表明，适量化合物填充，或合适浓度硝酸对活性炭纤维的表面处理，可以有效地修饰活性炭纤维的孔结构或改变活性炭纤维表面对氙的亲和力。因而可有效地提高改性活性炭纤维对氙的吸附容量。     

PREPARATION OF ACTIVATED CARBON FIBER AND THEIR XENON ADSORPTION PROPERTIES（Ⅲ）-ADSORPTION ON MODIFIED ACTIVATED CARBON FIBER

Structures of a series of activated carbon fibers were modified by impregnating them withorganic and inorganic materials such as Methylene blue(Mb)、 p-nitrophenol (PNP)、 NaCl or byoxidizing with KMnO4 or HNO3. The influence of pore filling or chemical treatment on their xenonadsorption properties was studied. The experimental results show that Mb and PNP filling ofactivated carbon fibers result in the decrease of xenon adsorption capacities of these treated ACFs,which is due to the decrease of their surface area and micro-pore volume. However, the adsorptioncapacity increases greatly with oxidizing treatment of activated carbon fibers by 7mol/L HNO3.     

活性炭纤维吸附氙气性能的研究：Ⅰ——原料不同对吸附性能的影响

本文选用６种纤维制备的活性炭纤维,研究了它们对氙气的吸附性能。结果表明,原料不同,导致产品吸附量明显不同,其中ＰＶＦ基活性炭纤维吸附氙气的性能最佳。     

中孔活性炭纤维对VB12的吸附性能研究

用炭黑政性聚丙烯腈原丝，制得了富含中孔的活性炭纤维，研究了它对大分子物质VB12的吸附性能。     

PREPARATION OF ACTIVATED CARBON FIBERS AND THEIR XENON ADSORPTION PROPERTIES（Ⅰ）-PREPARATION AND PORE STRUCTURE CHARACTERIZATION

A series of sisal based activated carbon fibers were preqared with steam activation at temperature from 750℃ to 900℃.Their pore structures were characterized through their nitrogen adsorption isotherms at 77K using different theories.The results showed that t-plot method and DR-plot method could suitably be used to characterize the mesopore structure and the multi-stage distribution of pore size of activated carbon fibers.It also showed that the pore size widens with the increase of activation temperature.     

常温下活性碳纤维对氙的动态吸附性能研究

本文研究了光致电离检测器的检测性能和四种活性碳纤维对氙的动态吸附,并且讨论了影响活性碳纤维动态吸附氙的两个影响因素,结果表明：光致电离检测器可以实现对氙的特征性检出;活性碳纤维对氙的动态吸附性能良好,是一种很好的氙吸附材料。     

Visualized observation of pores in activated carbon fibers by HRTEM and combined image processor

Image analysis has been applied to the TEM observation of activated carbon fibers, in order to evaluate the pore structure visually. It is suggested that the present method can show the shape of the pores as well as providing a quantitative estimation of the pore structure. The results are consistent with those obtained by common gas adsorption method and with synthesized molecular graphics TEM images of pores. The pore analysis on activated carbon fibers by TEM combined with image processing can provide a powerful tool to characterize the porous structure of activated carbons from a different new viewpoint.     

Characteristics of Nonafluorobutyl Methyl Ether (NFE) Adsorption onto Activated Carbon Fibers and Different-Size-Activated Carbon Particles

The characteristics of adsorption of 1,1,1,2,2,3,3,4,4-nonafluorobutyl methyl ether (NFE), a chlorofluorocarbon (CFC) replacement, onto six different activated carbon; preparations (three activated carbon fibers and three different-sized activated carbon particles) were investigated to evaluate the interaction between activated carbon surfaces and NFE. The amount of NFE adsorbed onto the three activated carbon fibers increased with increasing specific surface area and pore volume. The amount of NFE adsorbed onto the three different-sized-activated carbon particles increased with an increase in the particle diameter of the granular activated carbon. The differential heat of the NFE adsorption onto three activated carbon fibers depended on the porosity structure of the activated carbon fibers. The adsorption rate of NFE was also investigated in order to evaluate the efficiency of NFE recovery by the activated carbon surface. The Sameshima equation was used to obtain the isotherms of NFE adsorption onto the activated carbon fibers and different-sized-activated carbon particles. The rate constant k for NFE adsorption onto activated carbon fibers was larger for increased specific surface area and pore volume. The rate of NFE adsorption on activated carbons of three different particle sizes decreased with increasing particle diameter at a low initial pressure. The adsorption isotherms of NFE for the six activated carbons conformed to the Dubinin-Radushkevich equation; the constants BE(0) (the affinity between adsorbate and adsorbent) and W(0) (the adsorption capacity) were calculated. These results indicated that the interaction between the activated carbon and NFE was larger with the smaller specific surface area of the activated carbon fibers and with the smaller particle diameter of the different-sized-activated carbon particles. The degree of packing of NFE in the pores of the activated carbon fibers was greater than that in the pores of the granular activated carbons. Copyright 2000 Academic Press.     

Competitive Adsorption of Chloroform and Iron Ion onto Activated Carbon Fiber

Chloroform in tap water has been a significant problem because it may be a carcinogenic substituent. Iron ion exists in tap water because of dissolution from iron water pipes. Iron ions in tap water cause discoloration and a bad odor. The isotherms of chloroform and iron ion adsorption onto activated carbon fibers in a single solution (chloroform or iron ion) and in a binary mixture solution (chloroform and iron ion) were investigated to estimate the competitiveness between chloroform and iron ions. The amount of adsorbed iron ions increased with increasing pore volume of the activated carbon fibers, while that of chloroform decreased. The amount of chloroform adsorbed onto the activated carbon fibers in the binary mixture solution was greater than that in the single solution. These results indicate that the adsorption of chloroform and iron ion onto activated carbon fibers could be competitive.     

活性碳纤维对银离子还原吸附能力的改进

活性碳纤维不仅对有机物有高的吸附容量,对贵金属离子也具有强的还原吸附能力,可将Pd(Ⅱ）,Ag（Ⅰ）,Au（Ⅲ）等离子还原为金属单质。因而可用于提取矿液或加收废液中的贵金属。由此,提高或改善贵金属在活性碳纤维上的还原吸附容量或分布形成,显得非常重要。本文研究了活性碳纤维制备条件、表面氧化改性、以有负载有机物等对活性碳纤维还原能力的影响。结果表明,（1）制备条件对剑麻基活性碳纤维的还原能力有很大的影响。用H3PO4或ZnCl2活化的活性碳纤维对银离子具有更高的还原吸附容量,分别可达250和700mg/g,约为水蒸汽活化剑麻基活性碳纤维对银离子还原吸附容量的2倍和5倍。（2）过氧化氢、高锰酸钾、或硝酸等无机氧化剂对活性碳纤维进行表面改性,也能提高活性碳纤维的还原能力。结果表明,虽然改性活性碳纤维的比表面积和孔体积下降10-20%左右,但基表面含氧量及含氧基团的种类发生了改变。这些改性活性碳纤维对Ag(NH3)2^ 的还原吸附量大幅度提高,可达550mg/g以上。推断表面改性在活性碳纤维表面创造了更多有利于碱性条件下发生氧化还原的活性点。（3）在活性碳纤维表面负载适当的有机物如亚甲基蓝、苯胺或对硝基苯酚,也能显著提高活性碳纤维对Ag(NH3)2^ 的还原吸附能力。     

吸附树脂和活性炭对气体中苯的吸附研究

采用了动态吸附实验方法研究了吸附树脂NDA-201和椰壳型活性炭C1对苯蒸汽的吸附行为.对吸附平衡数据采用Dubinill-Astakov方程进行了拟合分析,并根据吸附剂孔结构特征探讨了吸附机理.实验结果表明,两种吸附剂的苯吸附等温线存在交叉现象,对高浓度苯蒸汽吸附治理可采用NDA-201树脂,低浓度则采用椰壳型活性炭C1;Dubinin-Astakov方程能用来对两种吸附剂的等温线进行拟合,表明吸附剂的微孔区域对吸附起着重要作用.微孔体积计算值的比较和特征曲线叠合的程度说明了.Polanyi吸附势理论更适合于描述椰壳型活性炭C1对苯的吸附,这可能是由于椰壳型活性炭C1的孔分布集中于微孔区,而NDA-201树脂除了微孔外还有一定量的中孔和大孔.     

Carbon molecular sieves for air separation from Nomex aramid fibers

Activated carbon fibers prepared from aramid fibers have proved to possess outstanding homogeneity in pore size, most of all when Nomex aramid fiber is used as precursor. Taking advantage of this feature, microporous carbon molecular sieves for air separation have been prepared through carbon vapor deposition of benzene on Nomex-derived carbon fibers activated to two different burnoff degrees. Carbon molecular sieves with good selectivity for this separation and showing acceptable adsorption capacities were obtained from ACFs activated to the two burnoff degrees chosen.     

STUDY ON THE FACTORS AFFECTING REDUCTION CAPACITIES OF ACTIVATED CARBON FIBERS

1. INTRODUCTION The discharge of effluent containing precious metal ions, which comes from electroplating, mining, smelting, and other industries, not only contaminate the environment where people live, but also cause the waste of natural resources. From…     

沥青基球状活性炭气相吸脱附行为研究

本文利用热重法研究了一系列沥青基球状活性炭对蒸汽及正已烷蒸汽的动态吸脱附曲线。结果表明,PSAC对苯蒸汽的吸附及再生性能优良。随吸附温度的降低、比表面积的增大、总孔容及微孔容的增大,PSAC对苯蒸汽的吸附容量增大。PSAC对正已烷的吸附速度大于对苯蒸汽的吸附速度,但其对正已烷的平衡吸附容量小于对苯蒸汽的平衡吸附容量。     

活性炭纤维吸附脱除NO过程中NO氧化路径分析

在小型固定床吸附实验台上开展了黏胶基活性炭纤维吸附脱除NO的实验研究。采用H₂O₂溶液浸渍以及热处理方法对活性炭纤维表面进行修饰,以获得表面孔隙结构接近而含氧官能团含量不同的样品;考察样品在惰性氮气气氛、含氧气氛下吸附脱除NO的效果,以及表面含氧含氮官能团的变化规律。探讨了含氧官能团在NO催化氧化过程中的作用及含氧气氛下O₂对于NO转化为NO₂的影响,分析了活性炭纤维表面吸附的NO向NO₂的主要转化途径。结果表明,在氮气气氛下活性炭纤维表面C-O官能团对吸附态的NO起到氧化作用,吸附态NO被C-O官能团氧化生成-NO₂官能团;在含氧气氛下活性炭纤维吸附NO后表面出现-NO₂、-NO₃官能团,通过长时间实验测定三种样品在含氧气氛下对NO吸附的效果,发现三种样品稳定时催化氧化效果一致,表明含氧官能团对初始NO的物理吸附影响较大,而对整个吸附过程影响较小。吸附在活性炭纤维表面上的NO与环境气氛中的游离态O₂发生氧化反应是NO转变为NO₂的主要途径。     

高度交联聚苯乙烯吸附剂的结构与吸附性能研究

在通过Ｆｒｉｅｄｅｌ—Ｃｒａｆｔｓ后交联反应制备高度交联聚苯乙烯吸附剂的过程中，向反应体系中加入非极性芳香化合物甲苯，当加入少量甲苯时，吸附剂的比表面积、孔容等变小，但其吸附能力却明显提高；当加入甲苯超过某一量时，其吸附能力又随加入甲苯的量的增加而降低，这说明孔结构和骨架结构共同影响着高度交联聚苯乙烯吸附剂的吸附性能．     

Modification of Activated Carbon Fibers and Their Characterizes of Adsorption for Xenon

Activated carbon fibers (ACFs) are characterizes by their highly developed internal surface area and porosity. Especially the development of micro- and mesopores is of great importance because it allows the carbons to adsorb large amounts and various types of chemicals from gases or liquids. Due to such a valuable feature, activated carbon fibers have been in use for many years. Porous carbon materials have now become extremely versatile adsorbents of major industrial significance. The high surface area and porosity of activated carbon fibers are the result of the activation process; physical or chemical activation. However, the complexity of the carbon structure, although voluminous research has been done and great effort has been made toward the control of pore size and its distribution^[1-3]. The recent development of industrial technology provides new application fields for porous carbons and,at the same time, requires the carbon to have a desired pore structure. To meet such a requirement, many novel approaches to control pore structure have been proposed.     

通过密度函数理论表征炭质吸附剂的孔径分布

通过密度函数理论（DFT-DensityFunctionalTheory）对炭质吸附剂的孔径分布进行了表征。该法以多孔固体上N2吸附分子模型为依据，用一种方法对多孔固体的孔径分布从微孔到大孔范围进行确定。本文用该法对自制的聚丙烯腈活性炭纤维、国产煤质活性炭及日本产活性炭微球等六种炭质吸附剂的孔径分布进行了表征。     

硝基苯在纳米炭黑上的吸附特征

利用炭黑作吸附剂,考察吸附质流速和硝酸处理浓度对炭黑吸附有机废水中硝基苯的影响,确定了最佳吸附处理条件,比较了不同炭素材料的吸附性能。实验结果表明:与炭管、椰壳活性炭和颗粒活性炭3种炭素材料相比,炭黑对硝基苯具有更佳的吸附性能。XRD、BET表征结果表明炭黑表面存在大约40nm介孔结构,毛细凝聚在吸附中起到了重要作用。