实心砖墙对电磁波的衰减特性

应用模式传输线理论分析了多层周期介质实心砖墙对电磁波的衰减特性。计算得到了电磁波穿透实心砖墙的透射反射系数与入射角和频率的关系曲线,数值计算的结果与软件仿真的结果符合较好。利用电磁波测量系统测量得到了实心砖墙对电磁波衰减随频率（2~8 GHz）的变化关系。综合考虑数值计算和实验测量的结果,得到频率为2~8 GHz时,实心砖墙对电磁波的衰减为15~25 dB。     

S—Ka频段电磁波在等离子体中传输特性的实验研究

在感应耦合等离子体风洞上开展了等离子体中电磁波传输特性实验研究,获得了不同频率电磁波在等离子体中的传输衰减.通过微波诊断技术,获得了等离子体射流的电子数密度和碰撞频率.通过矢量网络分析仪和标准增益天线组成的电磁波传输特性测试系统,获得了电磁波经过等离子体之后的衰减,研究了电子数密度范围7.0×10~(10)-1.0×10~(13)cm~(-3)、等离子体碰撞频率在109 Hz量级的等离子体对2.6—40 GHz不同频率电磁波传输特性的影响,分析了经典传输理论和薄层理论预测结果与实验结果的差异.该实验工作为等离子体中电磁波传输特性的理论研究和数值仿真提供了基础数据.     

WiFi电磁波能量在砖墙中的传播特性研究

WiFi电磁波的穿墙能力直接影响通信的效果和质量.结合砖墙的电磁特征,理论分析了WiFi电磁波在砖墙中的传播特性,推导出了WiFi电磁波穿墙厚度与平均功率流密度的关系式,给出能量传输实例及图像.结果表明:WiFi电磁波能穿透砖墙,穿透过程中信号能量逐渐衰减,但是衰减较小.因此,砖墙对WiFi通信连接的阻碍作用并不大.     

等离子体中电磁波传输特性理论与实验研究

本文对35 GHz和96 GHz电磁波在等离子体中的传输特性进行了理论与实验研究, 得到了电磁波衰减随等离子体密度、碰撞频率和电磁波频率的变化规律. 等离子体密度增加一个数量级时, 电磁波衰减增加一个数量级; 随着等离子体碰撞频率的增加, 电磁波衰减先增加后减小; 随着电磁波频率的增加, 衰减下降. 以激波管为实验平台进行了电磁波在等离子体中传输特性的实验研究, 实验结果和理论结果吻合较好. 理论和实验结果均表明, 提高电磁波频率是解决黑障问题的有效途径.     

太赫兹波在磁化等离子体中传输特性

建立了电磁波穿过磁化等离子体鞘套的一维模型,并采用数值分析方法对太赫兹（THz）电磁波在磁化等离子体鞘套中传播时的反射率、透射率和衰减值进行了计算仿真,分析了磁化条件下磁场强度、太赫兹波频率、等离子体鞘套厚度、等离子体碰撞频率和等离子体密度对太赫兹波在磁化等离子体鞘套中传播特性的影响。仿真结果表明:排除衰减波峰对应的频率范围,外加磁场有效降低了太赫兹波传输的衰减,在固定磁场强度下,衰减波峰两侧的衰减值均达到了5 dB以下,有效地解决了通信黑障问题。     

建筑墙体对电磁脉冲响应的FDTD分析

 采用时域有限差分法和傅里叶变换对电磁脉冲作用于建筑墙体后发生的反射和透射进行了比较全面的研究分析。采用周期边界实现了不同建筑墙体对电磁脉冲响应的数值计算，对计算的结果进行了讨论分析，研究结果表明：钢筋阵对低频段的屏蔽效果很好，当频率增加时，屏蔽效果变差。混凝土墙的频域波形具有明显的周期性，存在许多谐振频率，谐振时透过很大，谐振频率由墙的厚度、磁导率和介电常数决定，要提高墙的屏蔽效果必须增加墙的电导率，以达到一个比较好的屏蔽效果。钢筋混凝土墙的屏蔽效果和反射特性由钢筋和混凝土墙共同调制决定。     

掺还原铁粉混凝土板反射和透射性能

通过控制混凝土板的厚度、混凝土板中还原铁粉掺量、在混凝土板中加钢丝网,研究混凝土板对电磁波的反射和透射性能。反射率测量采用弓形架测试方法,透射衰减测量采用两端口测试方法。混凝土板对电磁波的反射率测试频段为2~18GHz,透射衰减测试频段为12~18GHz。不同的混凝土板对电磁波的反射率在-5dB左右。40mm厚的混凝土板中还原铁粉的掺量超过200kg/m3时,电磁波的透射衰减量可达到-50dB以上。通过分析实验结果,发现混凝土板的厚度、混凝土板中还原铁粉掺量和钢丝网对反射率大小影响较小,对透射衰减量影响较大。     

椭圆柱体对任意入射极化的电磁波的散射

基于电磁场的多尺度变换理论,得到了以导体椭圆柱为例的电磁波任意极化,任意垂直入射到目标上的散射场的解析式.将所得结果应用于计算圆柱目标的散射场,结果与文献完全一致.对椭圆柱体的散射宽度随入射波方位角,电磁波频率以及目标尺寸的变化进行了仿真.结果表明,在垂直于电磁波的方向上观测时,椭圆柱的垂直尺寸对散射有较大的影响,电磁波水平极化时散射最强.所用算法适用于介质椭圆柱等目标的散射特性研究,所得结果为目标尺寸、形状遥感电磁测量等实际应用提供了理论依据.     

基于Drude-FDTD算法的单负介质组合填充波导传播特性研究

提出了电单负介质和磁单负介质组合填充矩形波导结构,通过理论分析和修正的3D-Drude-FDTD算法进行数值仿真,分析了电磁波在其中的传播特性.仿真结果表明,新结构波导中存在异于传统介质填充波导的亚波长导模,且传播常数基本不随频率的变化而变化,可以用于宽带微波器件和天线的设计. 关键词： 单负介质 传播常数 截止频率 时域有限差分法     

电磁波在等离子体中的非线性吸收衰减

研究平面电磁波在等离子体中的非线性吸收衰减.首先应用电磁波在等离子体中传播的极化理论得到非线性介电函数,进而求出了考虑非线性情况下的波矢.采用垂直入射具有金属衬底的均匀等离子体模型,对不同入射频率的电磁波的衰减以及总出入射功率比进行了数值模拟.与只考虑线性情况的结果作了比较,结果显示非线性项在研究过程中所起的作用是不可忽视的.     

红外热像法研究空心砖墙表面温度

建筑墙体的室内表面温度直接反映墙体的保温隔热性能,并且作为室内平均辐射温度的主要组成部分对室内热环境有重要影响。针对建筑工程中大量使用的空心砖墙体具有表面温度不均匀的特点,采用ThermaCAM P20型红外热像仪和ThermaCAM Reporter分析软件,研究应用红外热像法测量空心砖墙体的表面温度,分析空心砖墙体的温度特征以及空心砖、 砌筑砂浆、 配砖等组成材料对表面温度分布的影响。在高层住宅建筑工程现场,选择三层住宅的填充外墙位置,使用不同的烧结页岩空心砖、 砌筑砂浆和配砖砌筑成三种空心砖墙体进行传热实验。通过采集三种烧结页岩空心砖墙体在冬季室内采暖条件下的内表面温度红外热像图,对比分析了两种空心砖和两种砂浆砌筑的墙体表面温度特性数据以及温度均匀性和温度频率分布。结果表明：提高空心砖和砌筑砂浆的保温性,能够有效提高墙体内表面温度,改善室内热环境;由保温砂浆代替水泥砂浆砌筑的节能型烧结页岩空心砖墙体,表面温度的不均匀性从0.6 ℃下降为0.4 ℃,并使表面温度频率分布发生变化,从非对称分布变为正态分布;随着表面温度均匀性的提高,平均温度所占的频率增大。本研究为空心砖墙体热功能的提高和优化提供了依据。     

Attenuation characteristics of obliquely incident electromagnetic wave in weakly ionized dusty plasma based on modified Bhatnagar–Gross–Krook collision model

The attenuation characteristics of obliquely incident electromagnetic(EM) wave in L-Ka frequency band in weakly ionized dusty plasma are analyzed based on the modified Bhatnagar-Gross-Krook(BGK) collision model.According to the kinetic equation and the charging theory,the total complex dielectric constant of the weakly ionized dusty plasma is derived by considering that the minimum velocity of the electron accessible to the dust particle surface is non-zero and the second potential part of the collision cross-section contributes to the charging.The attenuation characteristics within the modified model are compared with those within the traditional model.The influence of the dusty plasma parameters and the incident angle of EM waves on the attenuation in weakly ionized dusty plasma is further analyzed.Finally,the influence of different reentry heights on the attenuation characteristics of the obliquely incident EM wave is discussed.The results show that the effect of the minimum electron velocity and the second term of the collision cross-section on the attenuation characteristics of EM waves cannot be ignored.When the dust density and dust radius are changed,the trends of the attenuation of obliquely incident EM waves are consistent,but the influence of dust density is weaker than that of dust radius due to the constraint of orbit-limited motion(OLM) theory.The plasma thickness,electron density,and incident angle are proportional to the attenuation amplitude of EM waves.The effect of different reentry heights on the attenuation obliquely incident EM waves is related to the electron density and plasma thickness.     

介质镀膜空芯光纤在THz频段的传输特性

 理论分析了介质镀膜空芯光纤在THz频段的传输特性,得出了该光纤的特征方程及模式分布。利用射线光学原理计算了介质膜材料为聚酰亚胺、介质膜厚度为0.05 mm的光纤的衰减常数随介质膜内直径的变化情况。得出其主模在THz频段的衰减常数小于1 dB/m,该值远小于相同内径的金属圆波导在这一频段的衰减常数。模拟计算了介质膜厚度为0.05 mm、内径为1 mm,金属膜内径为1.05 mm的介质镀膜空芯光纤在0~1 THz的S参数,模拟结果显示该光纤在THz频段有很宽的通带,且在通带内衰减常数小于0.5 dB/m,可用于THz频段电磁波远距离传输。     

墙体对微波脉冲的衰减特性

 研究墙体对微波脉冲的衰减特性，测量了微波脉冲垂直入射墙体后的脉冲信号，经过计算得到普通砖混墙、普通钢筋混凝土墙、钢筋网混凝土墙对窄带微波和超宽带微波的衰减值；分析了微波脉冲穿越不同墙体的频谱变化。研究结果表明，普通钢筋混凝土墙和普通砖混墙对窄带微波脉冲的衰减为0.342～0.699 dB/cm，对超宽带信号的衰减为0.134～0.183 dB/cm。钢筋网混凝土墙（厚65 cm）对超宽带信号的衰减较大（29.07～45.79 dB），同时使穿透墙体的超宽带信号频率分布向高频位移。     

Investigation into the Effect of Dielectric Loss on RF Characteristics of Helical SWS

A general theory has been developed to account for the effect of the dielectric loss of discrete rods on the performance characteristics of an actual helical slow wave structure (SWS). The effect of the lossy dielectric rods has been studied on various propagation parameters, namely, phase propagation constant, interaction impedance and attenuation constant at different operating frequency. It is clearly shown that the influence of dielectric loss on RF characteristics is much larger at the millimeter frequency band than that at the microwave frequency band, especially on interaction impedance and attenuation constant. The general theory developed here has been further confirmed by comparing the results with those obtained elsewhere for some special cases.     

Frequency selective surface structure optimized by genetic algorithm

Frequency selective surface (FSS) is a two-dimensional periodic structure which has prominent characteristics of bandpass or bandblock when interacting with electromagnetic waves. In this paper, the thickness, the dielectric constant, the element graph and the arrangement periodicity of an FSS medium are investigated by Genetic Algorithm (GA) when an electromagnetic wave is incident on the FSS at a wide angle, and an optimized FSS structure and transmission characteristics are obtained. The results show that the optimized structure has better stability in relation to incident angle of electromagnetic wave and preserves the stability of centre frequency even at an incident angle as large as 80°, thereby laying the foundation for the application of FSS to curved surfaces at wide angles.     

A homogenised vibratory model for predicting the acoustic properties of hollow brick walls

The prediction and the physical understanding of sound transmission through masonry walls made of hollow bricks remain an open question. To solve this problem a semi-analytical approach is proposed. The inhomogeneous structures of the brick wall are homogenised and a simplified analytical model is established to calculate the transmission loss of an equivalent finite and multilayered anisotropic plate. An efficient numerical homogenisation technique is derived to define the equivalent anisotropic brick. This process only needs the knowledge of the elastic tensor of the brick material that has been determined using ultrasonic measurements. The features of the simplified brick wall have been then investigated through Lamb waves dispersion curves. Finally, the model has been used to explain the transmission loss curve of a wall and a good agreement between predictions and test data is obtained.