固相萃取-气相色谱串联质谱法测定饮用水中的多环芳烃和邻苯二甲酸酯

采用固相萃取、中性硅胶-中性氧化铝复合柱对水样进行提取和净化,采用气相色谱串联质谱法测定水样中的16种多环芳烃和6种邻苯二甲酸酯.该方法对水样中的多环芳烃和邻苯二甲酸酯的检测限分别为0.10～0.26 ng/L和0.20～2.0 ng/L,加标回收率分别在88.6％～111.7％和85.3％～110.5％之间,样品重复测定6次,相对标准偏差(RSD)均小于15％.实验结果表明,该方法灵敏度高、重复性好、定量准确,可用于饮用水中多环芳烃和邻苯二甲酸酯的测定.     

气相色谱-质谱法同时测定地下水中42种半挥发性有机污染物

建立了同时测定地下水中多环芳烃(PAHs)、多氯联苯(PCBs)、有机氯农药(OCPs)和有机磷农药(OPPs)等42种半挥发性有机污染物的分析方法,对固相萃取、液-液萃取、萃取溶剂和色谱柱等分析条件进行优化。最终采用乙酸乙酯-正己烷(1∶4)液液萃取,DB-5MS色谱柱分离,GC-MS/SIM测定,内标法定量。结果表明,42种目标物在0.5~1 000μg/L范围内线性关系良好(r20.995);方法检出限为0.05~3.08 ng/L。在10、40、400 ng/L加标水平下,42种目标物的基体加标平均回收率为73.0%~107%,相对标准偏差(RSD,n=5)为1.4%~11.3%。将方法应用于石家庄周边地区水样检测,结果可靠。该方法灵敏、准确、简单易行,可显著提高地下水中主要有机污染物的分析效率。     

竹炭固相萃取/气相色谱-质谱联用对环境水样中16种多环芳烃的测定

以竹炭为固相萃取吸附材料,考察了其对环境水样中16种多环芳烃的吸附富集能力,采用DB-35MS弹性石英毛细管色谱柱对16种多环芳烃进行分离,气相色谱-质谱联用法对多环芳烃进行定性及定量分析.结果表明,1 000 mg竹炭作为固相萃取吸附剂,10 mL二氯甲烷作为洗脱剂,上样速率5 mL/min,水样中甲醇体积分数为15%的条件下,16种多环芳烃有较好的回收率,竹炭固相萃取柱的穿透体积大于500 mL,通过实验比较竹炭的萃取回收率优于商品化的C18固相萃取柱.16种多环芳烃的质量浓度在10 ～500 ng/L范围内与峰面积的线性关系良好(苯并(k)荧蒽,苯并(a)芘,二苯并(a,h)蒽,苯并(g,h,i)苝为25 ～500 ng/L),相关系数为0.983 6 ～0.998 4.方法的检出限为0.6 ～8.0 ng/L,实际水样的加标回收率为67% ～113%,相对标准偏差为2.1% ～11.3%.通过对白沙河河水的分析表明,该方法能够满足实际水样的测定,竹炭可以作为固相萃取材料应用于水中16种多环芳烃的分析测定.     

亚临界水萃取及气相色谱-串联质谱法检测红茶中多种农药残留

建立了亚临界水萃取及气相色谱-串联质谱(GC-MS/MS)检测红茶中21种有机氯和拟除虫菊酯农药残留的方法。在萃取压力为5 MPa条件下,样品经150 ℃的亚临界水提取15 min后,将目标物转移至丙酮-正己烷(1:1, v/v)中,经ENVI-Carb固相萃取净化小柱净化,DB-5毛细管气相色谱柱分离,在多反应监测(MRM)模式下进行MS/MS检测,基质匹配溶液内标法定量。各目标物在5.0～320.0 μg/L范围内线性关系良好,相关系数均大于0.99,其定量限(信噪比(S/N)＞10)为50 ng/g,检出限(S/N＞3)为10 ng/g。茶叶基质中添加50、100和200 ng/g的标准品时,21种农药的回收率为70.18%～119.98%,相对标准偏差(RSD)为5.01%～11.76%。该方法的灵敏度、准确度和精密度均符合农药残留测定的技术要求,适用于红茶中有机氯和拟除虫菊酯农药残留的检测。     

固相萃取-气相色谱-质谱联用快速检测地下水中13种有机氯农药及苯并(a)芘

通过优化固相萃取条件,改进色谱分离条件,建立了一种快速测定水中13种有机氯和苯并(a)芘的GC-MS方法。方法的特点是前处理速度快、污染小、色谱运行时间短,可以在20 min内完成检测,适于大批量样品分析。采用分段法选择离子(SIM)扫描,具有更高的灵敏度。该方法均有较低的检出限和较高的回收率,检出限均低于5.0 ng/L,回收率范围78%~110%。     

使用C18固相萃取膜-色质联用定量分析饮用水中痕量多环芳烃的初步研究

参照美国EPA525.1方法,C18-固相萃取膜萃取饮用水中的有机物,利用GC/MS法鉴定多环芳烃(PAHs),使用16种多环芳烃混合标准样绘制标准曲线,以内标法对PAHs进行定量分析.采用本方法研究某水厂经过深度处理后的出厂水中的7种多环芳烃的含量,PAHs的平均回收率为94.0%～97.7%.检测限为0.001μg/L.     

固相萃取-气相色谱法检测血清中有机氯农药残留的研究

建立了血清中DDTs和BHCs共8种有机氯农药残留的固相萃取-气相色谱检测方法。样品经超声酸化沉淀蛋白后,采用正己烷-丙酮(9∶1)经Cleanert ODS C18N固相萃取小柱提取,Florisil固相萃取小柱净化,氮气吹干,以500μL正己烷定容,气相色谱-电子捕获检测器(GC-ECD)进行定量分析。结果表明,方法的线性范围2~200 ng/m L,相关系数(r)为0.996 4~0.999 0,检出限(LOD)为0.1~0.9 ng/m L,定量下限(LOQ)为0.4~3.0 ng/m L。8种农药的回收率为80.5%~112.7%,相对标准偏差(RSD)为2.1%~7.9%。该方法具有较高的准确度和精密度,适用于血清样品中痕量有机氯农药的检测。     

快速溶剂萃取-气相色谱-质谱法同时测定土壤中多环芳烃、六六六和滴滴涕

建立快速溶剂萃取-气相色谱-质谱法同时测定土壤中多环芳烃、六六六和滴滴涕。优化了提取溶剂和洗脱溶剂,采用加速溶剂萃取法处理土壤样品,萃取溶剂为二氯甲烷-正己烷(1∶1)。提取液用氮吹仪浓缩、硅酸镁固相萃取小柱净化,用二氯甲烷-正己烷(3∶7)混合溶剂对固相萃取小柱进行活化和洗脱,流出液净化后氮吹浓缩至1 mL,利用气相色谱-质谱内标法进行分析定量。16种多环芳烃、8种有机氯农药及3种替代物在5.0～500μg/L范围内线性良好,方法检出限为0.000 55～0.000 77 mg/kg,加标回收率为68.2%～112.7%,相对标准偏差为4.3%～10.1%(n=5)。该方法可用于同时测定土壤中多环芳烃、六六六、滴滴涕的含量。     

全二维气相色谱-飞行时间质谱测定地下水中低环多环芳烃及其衍生物

建立了地下水中低环多环芳烃及其衍生物的全二维气相色谱-飞行时间质谱(GC×GC-TOF MS)检测方法。对比研究了液液萃取(LLE)和固相萃取(SPE)对地下水中低环多环芳烃及其衍生物的提取效率,优选液液萃取为前处理方法。在优化条件下,除1,2,3,4-四氢萘(r=0.987 2)和联苯(r=0.989 9)外,其它目标物在0.1~1 000μg/L范围内具有良好的线性关系,相关系数(r)均大于0.99。地下水的平均加标回收率为63.3%~111%,除喹啉的相对标准偏差(RSD,n=6)为24.9%外,其余目标物的RSD均小于9.5%,方法检出限在1.63~14.7 ng/L之间。该方法用于河北地区6个地下水样中低环多环芳烃及其衍生物的检测,4个样品有检出,最高浓度达353 ng/L。     

应用搅拌棒吸附萃取-热脱附-气相色谱/质谱法快速测定滇池水系中的16种多环芳烃

应用搅拌棒吸附萃取(SBSE)-热脱附(TDS)-气相色谱/质谱联用(GC/MS)方法测定了滇池水系(滇池和盘龙江上、中、下游)中16种多环芳烃(PAHs)的含量。方法快速简便,无有机溶剂污染,PAHs的最低检出限为1.0~468.8 pg,理论回收率在90%以上,加标回收率为83.1%~109.4%,相对标准偏差小于10%。测定结果表明,这16种多环芳烃在滇池水样中的含量为89.16 ng/L,在盘龙江上游水样中的含量为65.41 ng/L,在盘龙江中游水样中的含量为339.22 ng/L,而在盘龙江下游水样中的含量为62.25 ng/L,说明滇池水系已经受到一定的PAHs污染,加强对滇池、盘龙江中PAHs有机污染的控制势在必行。     

A reactive analytical approach for the estimation of olefinic content in gasoline-range hydrocarbons by gas chromatography

The estimation of olefinic content in conversion processes such as the etherification of olefins in fluid catalytic cracking (FCC) gasoline is essentially required. Gas chromatography (GC) is the well-established method for the quantitative analysis of olefins in etherification processes. The current state-of-the-art GC methods employing highly specific long single capillary columns such as Petrocol-DH are being used for the analysis of gasoline-range hydrocarbons. However, the method needs many standard reference samples of respective components in a complex mixture of hydrocarbons, which limits the scope of the analytical method. The alternative approach followed by this investigation is based on the reactive method of the analysis of olefins in FCC light gasoline by subjecting them to hydrogenation and estimating the olefinic content by GC comparing the gas chromatograms of the original feed and hydrogenated product using a Petrocol-DH column. A decrease in the quantity and disappearances of the peaks are assumed as olefins, and their number and total composition is calculated. In this study the bromine number method is used to estimate the olefinic content for a comparison of results with the adopted proposed methodology. The adopted methodology quantitates olefinic content in FCC light gasoline, which is comparable with reported literature values and the bromine number method. With the availability of standard reference samples of some important major reactive olefins, the adopted methodology can also give component-wise analysis as well as total olefinic content in a single step in processes such as etherification. The methodology can be also useful in reactions in which the conversion of total olefinic content is needed such as hydration, esterification, and alkylation of olefins in a complex mixture of hydrocarbons apart from the etherification of olefins in FCC gasoline.     

正相液相色谱-蒸发光散射法测定食品中的石蜡

采用液相色谱(HPLC)结合蒸发光散射检测器(ELSD)对食品中的石蜡残留物进行了分析和检测.利用正相色谱柱对石蜡和非石蜡组分进行了分离,而无需对石蜡组分进行逐一分离.利用t检验,对构成石蜡的烷烃组分在ELSD检测器上的线性响应进行了显著性误差分析,结果显示,石蜡中烷烃组分具有相似的线性响应.以此为定量依据,实现了食品中石蜡含量的快速定量分析.并对HPLC-ELSD的检测和确证结果与GC-MS法进行了对比.方法的线性范围为10～500 mg/L,相关系数为0.9988;检出限为1 mg/L.以10, 50和100 mg/kg浓度水平添加石蜡时,其回收率在84.6%～105.4%之间,相对标准偏差为5.4%～7.2%.     

用紫外分光光度法和电位滴定法测定几种植物激素的电离常数

分别采用紫外分光光度法和电位滴定法测定了脱落酸、3-吲哚乙酸、赤霉素、水杨酸等几种植物激素的电离常数,对比分析了两种测试方法的原理、测试步骤和数据处理方法.结果表明,采用两种方法测定的四种样品的电离常数与文献报道值一致,且测量结果的重现性较好;这表明紫外分光光度法和电位滴定法可方便地用于测定有机化合物的电离常数.     

Using RGB filters and a circularly polarized system to measure the deflection radius of optically anisotropic-polymeric substrates with a sub-grayscale resolution

Transparent optically anisotropic substrates (TOASs) are a crucial component in flexible electronics. Moreover, knowing the deflection radii of TOASs is essential to estimate the residual stresses of the thin films deposited on them. This paper proposes a novel measurement method to measure the deflection radii of polyimide (PI) substrates. Red, green, and blue filters and a circularly polarized system were used in the proposed method to investigate the influence of measurement precision on the wavelength of light adopted. Moreover, the image averaging technique was adopted to significantly reduce the noise in the fringe. Thus, the proposed method could be performed using only one set of image information and the measurement resolution could be improved to the sub-grayscale order. The experimental results reveal that red light can be adopted to precisely measure the deflection radii of PI substrates (error of 2.90%) However, large errors are caused when green light is used (22.35%). The experimental results reveal that blue light cannot be used to obtain any interferometric fringe patterns to calculate the deflection radius.     

Derivation from coupled channel equations of the resonance raman scattering amplitude for a diatomic molecule

The coupled equations of molecular collision theory can be formulated in such a way as to yield the amplitude for resonance Raman scattering of light by a diatomic molecule. Two variants of the method can be adopted, characterized by different choices for the potential matrices. All molecular potentials, either analytical or numerical, are treated on the same footing. Tests of accuracy are presented for the case of harmonic potentials intersected by linear potentials, for which an exact analytical solution can be given.     

用手性高效液相色谱法拆分并测定氯苄哌醚联苯酰苯甲酸盐(英文)

氯苄哌醚联苯酰苯酸盐主要用于止咳,L-氯苄哌醚联苯酰苯酸盐具有更高活性.采用手性色谱柱,建立了氯苄哌醚联苯酰苯酸盐光学异构体的拆分方法,并将其用于氯苄哌醚联苯酰苯酸盐的检测.结果表明,采用Chiralcel OD-H柱,在流动相V(正己烷)∶V(异丙醇)∶V(二乙胺)=98∶2∶0.1的条件下,2个异构体能同时达到基线分离,检测波长为254nm,氯苄哌醚联苯酰苯酸盐检测极限为10ng.这表明所建立的分离分析方法可方便可靠地用于该化合物的光学纯度检测.     

A prototype industrial sensing system for phosphorus based on micro system technology

Progress in the development of a miniaturised microfluidic instrument for monitoring phosphorus in natural waters and wastewater is presented. The yellow colorimetric method for phosphate analysis has been transferred to a microfluidic chip configuration This simple method employs one reagent mixed in a 1:1 ratio with a sample to produce a yellow colour absorbing strongly below 400 nm. A stopped flow approach is used which, together with the very rapid kinetics and simple reagent stream, enables a very uncomplicated microfluidic manifold design to be adopted. The working wavelength is 380 nm to coincide with the peak output of a recently developed UV-LED narrow bandwidth light source. The limit of detection for the yellow method is 0.2 ppm with a dynamic linear range from 0-50 ppm possible. The reaction time at room temperature is less than 3 min, which means that up to 20 samples per hour can be analysed.     

One-shot screen-printed thylakoid membrane-based biosensor for the detection of photosynthetic inhibitors in discrete samples

A method is developed to determine the optimal profile of zeta potential around U turns such that the turn-induced spreading of a solute band is minimized. After proposing a velocity profile that eliminates the racetrack effect, a conjugate gradient method is adopted to find the zeta potential profile to induce the required velocity. The optimal profiles of zeta potential seem to be insensitive to the relevant parameters of electroosmotic flows. It is shown that a reduction of variance two orders of magnitude below that of a comparable turn with uniform zeta potential is easily attained by adopting the optimal profile of zeta potential, which can be realized using a UV excimer laser or external voltage control.     

The use of stabilizers in the UV assay of ascorbic acid

Sodium thiosulphate (0.04%w/v) has been used to stabilize ascorbic acid in aqueous medium. The method has been used to assay ascorbic acid in commercial tablet preparations. It is very accurate, precise and reproducible. It compares favourably with official titrimetric method. The method is simple and can be adopted for the routine assay of ascorbic acid in single component tablet formulations.     

毛细管气相色谱法测定二乙基二硫的含量

采用毛细管气相色谱法(GC)测定了二乙基二硫的含量.结果表明,二乙基二硫含量在0.01⁰.4g/L范围内具有良好的线性关系,平均回收率为99.91%;该方法简便、准确、重复性好,可方便地用于二乙基二硫含量的测定.